Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Items: |
| 2 | Providing, Supplying & Fixing of T.W boarding 25 mm thick well seasoned CP teak wood without knots or cracks, in design plank. work done by Laying in Roof with Required All Loading,Unloading, Necessary Labour, Tools, Scaffolding, staging, Hardware Etc Complete As per Directed by Engineer - In -Charge. |
| 3 | Providing, Supplying & Fixing of Dungry cloth over the entire surface of wooden boarding having the hot bitumen coating below to stick the dungry cloth & then spread the cloth. Post spreading the cloth the hot bitumen to be applied using a long brush with a long stick. Application to be done uniformly over the entire surface of TW Boarding Area with Required All Loading,Unloading,Necessary Labour, Tools, Scaffolding, staging, Hardware Etc Complete As per Directed by Engineer - In -Charge. |
| 4 | Providing, Supplying & Fixing of Wacker on Mangalore Tiles : Application of high quality wacker SMK 1311 Solvent free silicone water repellent coating impregnating on the Mangaloretiles by spray. The dilution with water should be done in a ratio of 1:14 ie I part od solution & 14 parts of wacker 1311 solution. The dilution should be applied in 2 or 3coats, wet on wet surface. The dilution should be applied either with brush or by spry. The application should be done after surface is prepared for it. The contractor is to adhere to manufacturer’s specification.with Required ,Scaffolding, staging, Hardware, Labour Tools,Loading,Unloading etc Complete As per Directed by Engineer - In -Charge. |
| 5 | Providing, Supplying & Fixing of Zero Puncture Aluminium sheet of 24 Gauge, & bent in such a way that Plain Sheet comes at bolts, nuts, screw, nails etc. Aluminium sheet fixed between horizontal battens & vertical battens ,As per Drawing including SS screws, SS coils streakers with joining overlapping sheets. including All Loading,Unloading,Necessary Labour, Tools,Scaffolding, staging, Hardware Etc Complete As per Directed by Engineer - In -Charge. |
| 6 | Providing, Supplying & Fixing of C P. Teak wood battens of size 40mm x 25mm for Fixing of Aluminium Sheet Roof Work including 1 coat of Black Japan on all sides, fixing with SS screws (304) or brass screws as per directed by the Engineer In-charge including All Loading,Unloading,Necessary Labour, Tools, Scaffolding, staging, Hardware Etc. |
| 7 | Providing, Supplying & Fixing of C P. Teak wood battens of size 50mm x 25min for Man galore tile roof work including providing 1 coat of Black Japan on all sides, fixing with SS screws (304) or brass screws as per directed by the Engineer In-charge. cost including for All Loading,Unloading,Necessary Labour, Tools, Scaffolding, staging, Hardware Etc |
| 8 | Providing, Supplying & Fixing of Roof pressed clay tile (Man galore tile with class \\"AA\\" tiles) of 20 mm nominal thickness & of approved size & as per approved pattern on wooden batten frame work complete including ridge batten etc. all complete.Cost Including for Scaffolding, staging, etc. |
| 9 | Providing, Supplying & Fixing of Ridge Tiles & hip tiles of class 'AA' painting with coloured cement mortar & curing etc Complete with Required Hardware, Labour Tools, Scaffolding, staging, etc etc Complete As per Directed by Engineer - In -Charge. |
| 10 | Providing, Supplying & Fixing of Design eves boards 250-300 mm wide & 25 mm thick well seasoned CP teak wood without knots or cracks ,in design boards as directed by architect ,etc .Complete with Required Hardware, Labour Tools, Scaffolding, staging, etc etc Complete As per Directed by Engineer - In -Charge. |
| 11 | Providing, Supplying & Fixing of Plain eves boards 250-300 mm wide & 25 mm thick well seasoned CP teak wood without knots or cracks ,in design As per Directed by Engineer - In -Charge.Cost Including for Scaffolding, staging, Labour , tools etc. |
| 12 | Rebaring : Providing material and labour for Drilling/ Cleaning hole and injecting grouting chemical with the help of dispenser, in to Stone masonry/RCC wall , Column, beam, Slab etc (Any Height , Any floor) (with Hilti RE500 V3 injection system or Fischer FIS EM injection system or Equivalent) as per manufacturer's specification and structural consultant's specification and fixing rebar of the required diameter subsequently up to 10 mm dia. drill hole and 300mm anchoring depth. Fixing methodology shall be followed as per manufacturer’s guidelines. Steel will be paid under relevant item. Manufacture to submit Rebar Depth Calculation based on design loads & other parameters as provided by consultant and in accordance with EOTA-TR-023/029 “guidelines for post installed rebar connections” for approval. Rate shall be inclusive of all material, labour, necessary scaffolding etc complete for all floors, all height as directed by engineer in charge. |
| 13 | Providing and fixing Double scaffolding system on the exterior side of building/structure, up to 8metre height, above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracing, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. Note:- (1) The elevation area of the scaffolding shall be measured for payment purpose. (2) The payment will be made once only for execution of all items for such works. |
| 14 | Water proofing Treatment, Water Proof Plaster: Providing Material Labour & laying of Water proofing treatment in Swimming Pool (Internal Surfaces) by Cleaning the surface area to be treated with high pressure water jet ,removal of loose particles by wire brush, cutting cold joints (floor to wall-horizontal / wall to wall-vertical and construction) junctions by 1”x 1” groove by means of electric breaker and pack it with Non Shrink Mortar(Micro Concrete). & Applying of Acrylic cementation self curing waterproofing system - Brush coat in three layers with Glass Fiber cloth of 10 x 10 mm aperture size in 3-4 mm thickness after proper cleaning of surface (Consumption of Brush coat material i.e. 5 Ltr Liquid + 10 kg. Powder in Pack covers 4 Sq M) etc.Complete as per direction of Engineer-in-charge. The rate includes preparation of surface, Treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.Complete with All Material,Labour, tools, Scaffolding etc. |
| 15 | Providing Material and labour for15 mm thick water proof cement plaster using water proofing powder 1Kg/1bag of cement for all floors on brick / concrete wall work using water proofing materials in CM 1:3 (1-cement : 3-coasrse sand) including finishing with a floating coat of neat cement slurry etc complete for Above Plinth to All Floor |
| 16 | Providing material and labour for Grouting the joints of any type of flooring tiles up to 4mm wide joints and in full depth, using Epoxy grout mix of 0.70 kg of organic coated filler of desired shade and approved make (0.10 kg of hardener and 0.20 kg of resin per kg), including filling/ grouting and finishing complete as per direction of Engineer-in-charge. |
| 17 | Swimming Pool Filtration System & Equipment : Providing, Supplying & Installation of Filtration System as per Bellow Specification Consisting of Tank diameter: 1400 mm (1.4 m) Filter area: approx. 1.53 m² Design / maximum flow: approx. 68 m³/hr Sand media required: approx. 1700 kg (for 0.5-0.8 mm sand) Maximum working pressure: around 2.5 bar (= ~36 psi) for TM series filters. Suitable sand size: ~0.4-0.8 mm (or similar) for this style of filter. Construction: Fibreglass-reinforced polyester resin (bobbin wound), UV & corrosion resistant. Complete Proper installation & Backfill as per Directed By Engineer in -Charge (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 18 | Providing, Supplying & Installation of Commercial Multi port Valve as per Below Specification Valve port size: 2.5″ (≈ 65 mm nominal)Valve functions: 6-way multi-port (Filter / Backwash / Rinse / Waste / Recirculate / Closed) Max operating pressure: approximately 2.5 bar (≈ 36 psi) common in similar filters. Material: heavy-duty ABS / GFPP (glass-fibre reinforced polypropylene) body + stainless steel internals for durability.Suitable for use with sand-bed filtration systems in pool or water-treatment applications. Complete installation as per Directed By Engineer in -Charge (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 19 | Providing, Supplying & Installation of Heavy Commercial Filtration System Pump as per Below Specification Consisting of required Power: 4 HP Application: Pool circulation / filtration (medium to commercial swimming pools). Material: Pump body, pump foot and diffuser in glass-fibre-loaded polypropylene; motor housing in aluminium (AL-2521); stainless steel (AISI 420) shaft; impeller and seal mounting in PPO (polyphenylene oxide) plastic. Motor class: Insulation Class F, asynchronous two-pole motor, continuous operation, IP55 protection. Typical flow rate: ~ 60,000 litres per hour (for the 4 HP model) as listed under “Flow Rate | 60k per / Hr” for BWFP0400 Voltage / Frequency: 220 V, 50 Hz complete installation as per Directed By Engineer in -Charge (Make & Model as Per Selection of Consultant as per listing for similar models or Selection of Higher Authority) |
| 20 | Providing, Supplying & Installation of Commercial Vacuum Fitting as per Bellow Specification Consisting of Internal diameter: 50 mm (Approx), External joint size: 2 inch, Material: ABS plastic Usage: Suction inlet for concrete pool (vacuuming) with complete installation as per Directed By Engineer in -Charge (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 21 | Providing, Supplying & Installation of Gutter Drain as per Bellow Specification Consisting of Gutter Drain Made From ABS plastic, heavy-flow design for handling larger volumes of water Flow rate 850Ltr/Hr Complete installation as per Directed By Engineer in -Charge (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 22 | Providing, Supplying & Installation of High Grade Floor Inlet as per Bellow Specification Consisting of Floor Inlet Made From ABS material with Bottom inlet for concrete pool with 50 mm internal & 2″ external fitting (after tiling) Flow rate: 10k (approx.) with complete installation as per Directed By Engineer in -Charge (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 23 | Providing, Supplying & Installation of High Grade Main Drain as per Bellow Specification Consisting of Main Drain Cover 12'' x 12''Made From ABS material , Flow Performance guideline : Max recommended velocity through drain pipe is 1.5 m/s with complete installation as per Directed By Engineer in -Charge (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 24 | Providing, Supplying & Installation of Commercial Chlorine Feeder as per Below Specification Consisting of Chlorine Cartridge FilterInlet/outlet connection: 1.5″ union , 11.4M³/H Chlorine Capacity 11 Kg complete installation as per Directed By Engineer in -Charge (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 25 | Providing & Supplying of Maintenance Kit as per Bellow Specification Consisting of Basic PH & CL Test Kit Purpose: Measures pH and free chlorine (Cl) in pool water Includes: Reagent bottles (typically indicator for pH + indicator for chlorine) Format: Manual drop test with color comparison Usage: Ideal for routine pool water monitoring Typical contents/volume: ~ 20 mL of pH reagent + ~ 20 mL of chlorine reagent (based on similar kits) Reading range: For free chlorine: ~ 0.1-2.0 mg/L Cl₂ (common for pool kits) Reading range: For pH: ~ 6.8-8.4 (typical pool pH range for indicator kits) with complete Stored at Located Storage as per Directed By Engineer in -Charge (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 26 | Providing & Supplying of Maintenance Kit as per Bellow Specification Consisting of High Quality Leaf Net Deep W/Gold Type: Deep-bag style leaf net for pools Net material: Polypropylene or woven mesh (designed to trap deeper sediment/debris) Frame & connection: Made to attach to a telescopic pole (via butterfly nut/clip) according to similar spec sheets Weight (for comparable “Leaf Net Deep” model): ~ 0.30 kg complete as per Directed By Engineer in -Charge. |
| 27 | Providing & Supplying of Maintenance Kit as per Bellow Specification Consisting of High Quality Telescopic Pole Length Range: approx. 12 ft to 24 ft (i.e., about 3.7 m to 7.3 m) Material: Aluminium alloy (likely anodised or corrosion-resistant) Extension mechanism: Two-section or multi-section with locking cam or twist lock device (for pool cleaning uses) Intended Use: For pool cleaning accessories (nets, brushes, skimmers, vacuum heads) — designed to reach deeper / larger pools Connection end: Universal size to attach standard pool tools (brushes, nets, vac heads) with complete Stored at Located Storage as per Directed By Engineer in -Charge (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 28 | Providing & Supplying of Maintenance Kit as per Bellow Specification Consisting of High Quality Flexible Vacuum Hose Length: 15 m (approx.) (≈ 50 ft) Internal diameter: 38 mm Material: EVA (extruded & poly-welded EVA cuffs) — spiral-wound construction for flexibility, strength & crush resistance Ends/cuffs: Standard cuff link on one end, swivel cuff for kink-free manoeuvre on the other, UV & chemical resistant Weight & dimensions (approx): Listed as ~ 4.52 kg, box size ~ 50.8 × 50.8 × 20.3 cm with complete Stored at Located Storage as per Directed By Engineer in -Charge (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 29 | Providing & Supplying of Maintenance Kit as per Bellow Specification Consisting of Heavy Quality Brush Algae 10\\" SS Size: 10″ head width (≈ 25 cm) Bristles: Stainless steel bristles for aggressive algae removal from pool walls/floor Back/frame: Hard plastic or aluminum-reinforced back compatible with pool poles Connection: Fits standard telescopic pool cleaning poles (pole sold separately) with complete Stored at Located Storage as per Directed By Engineer in -Charge (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 30 | Providing & Supplying of Maintenance Kit as per Bellow Specification Consisting of Vacuum Head Professional Grade 22'' 2''/1.5'' Head width: 22 inches (~56 cm) (as described for “22 Inch Vacuum Head Professional Grade”) Vacuum port options: Accepts both 2-inch and 1.5-inch hose ports (2″ / 1.5″) — hence dual-port compatibility. Design: Professional-grade pool vacuum head for floor & wall cleaning of pools, compatible with standard pool hoses and telescopic poles. Material & body: While exact material specs for this model aren’t found, typical heads of this size from the brand use durable aluminium or heavy-duty plastic bodies suited for commercial use. with complete Stored at Located Storage as per Directed By Engineer in -Charge (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 31 | Providing & Supplying of Maintenance Kit as per Bellow Specification Consisting of 18'' Poly wall Brush Head size: 18 inches (≈ 45.7 cm) width — coverage for pool walls/floors. Bristles: Poly (polypropylene/polyester) bristles designed for general surface scrubbing — safe for vinyl, plaster, tile.Back/frame: Aluminium (“Alu”) back / frame for strength and light weight — good durability and corrosion resistance.Connector: Fits standard telescopic pool poles (pole sold separately) so it attaches to cleaning handles for pool walls. Intended use: Wall & floor cleaning of swimming pools - scrubs away grime, algae, debris from surfaces. with complete Stored at Located Storage as per Directed By Engineer in -Charge (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 32 | Providing, Supplying & Installation of Heat Pump as per Bellow Specification Consisting of Heat Pump Heating capacity: ~ 115 kW (as indicated by model “115 kW”) Application: Pool / swimming-pool heating (commercial / large-scale). (India market) Probably 3-phase power supply (given very large capacity) with complete installation as per Directed By Engineer in -Charge (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 33 | Providing, Supplying & Installation of Pool Control Panel as per Below Specification Consisting of Pool Control Panel 12 KW ,1 Phase, Main supply voltage: e.g., 230 V AC or 400 V AC, single-phase or three-phase depending on system size. Control functions: Timers, surge protection, digital timer for pump/aux switching. For Swimming Pool including all fittings & Accessory with complete installation as per Directed By Engineer in -Charge (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 34 | Providing, Supplying & Installation of Heat Pump Control Panel as per Bellow Specification Consisting of Heat Pump Control Panel, 230KW, 3 Phase Supply voltage: 380 415 V AC, 3 phase, 50 Hz (common for large commercial equipment). Main power rating: Sized to handle the 230 kW load + motor/pump starters + safety margin. Control circuits: Includes PLC/microcontroller or timer logic for sequences (e.g., pump start, compressor start, defrost, alarms) Safety interlocks: Flow switch sensor, high/low pressure sensors, high/low temperature sensors on water side, freeze protection.Wiring & cable sizing: Cables sized to handle full load current (FLA) of the 230 kW system + start inrush; adequate cable cross‑section, proper terminations. Cooling or ventilation of the panel: For large loads the control panel may need forced ventilation or internal air circulation. with complete installation as per Directed By Engineer in -Charge (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 35 | Providing, Supplying & Installation of Double Pin Grating as per Below Specification Consisting of Double Pin Over Flow Grating 300mm x25mm White Width: 12 inches (~300 mm) — this is the channel cover width. For example one manufacturer lists a 12″ width version. Pin style: Double pin (also called “two pin”) meaning two rows of load bearing pins in the design for support and interlocking with channel. Multiple manufacturers reference two pin models for 12″ width. Material: Generally outdoor-grade PVC, ABS or Polypropylene copolymer with UV stabilisation and chemical resistance (pool chemicals). E.g., listing mentions “highest quality outdoor grade PVC … UV-stabilised” for white 12″ grating. Colour: White (often with optional bone, grey). White helps visual uniformity with pool edge and avoids heat absorption. Height/Thickness: Typical thickness/heights around 25 mm or 35 mm for injection moulded pool grating. Example: size 300/12″ has height 25mm. Chemicals & UV Resistance: UV tested (>750 hours) and chemical resistant in pool environments (chlorine etc). Modularity / Compatibility: Often available in straight and radius sections, connectable plug in designwith complete installation as per Directed By Engineer in -Charge (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 36 | Providing, Supplying & Installation of Quantum as per Below Specification Consisting of 110 watt ,Model Q-130-UK & Material High Quality Plastic Material & Electric Supply with complete installation Lamp Output / Power: 110 W.Suitable Pool Volume (maximum): ~ 130 m³. Flow Range / Max Flow: Up to ~ 28 m³/h (given reference “Double 110W” series) Technology: Combines UV + photocatalytic / hydroxyl radical oxidation (TiO₂/Mo) for sterilisation of pool water. Compatible with salt & sea water systems. Lamp life: Approx ~ 2 years average service life. Electrical supply: 1 phase power (for this model) at ~100 240 V range. Water connections: 2″ (63 mm) ABS unions + reducers for 1½″ (50 mm). Max working pressure ~3 bars. Meticulously designed, Elecro have developed the rst coste ective, photocatalytic oxidiser speci cally for the swimmingpool industry, for a toxin free swimming sensation. Not only doesit eliminate undesirable side-e ects such as sore eyes, itchy dryskin, discoloured hair and strong odours, but it also makes watercrystal clear, and most importantly it creates no risk to the lungsor health of bathers and swimming pool attendants.(Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 37 | Providing, Supplying of Chlorine Tablets Consisting of TCCA 90 Chlorine Tablets (200 G x 5 Nos = 1 Kg pkt) “Trichloroisocyanuric Acid (TCCA) 90 % Chlorine Tablet – 200 g (pack of 5 = 1 kg total)” used in pool water treatment:Chemical name: Trichloroisocyanuric Acid (TCCA) — CAS No. 87 90 1. Available (active) chlorine content: ≥ 90 %. Tablet weight: approx 200 g per tablet. pH of a 1% aqueous solution: about 2.6 – 3.3. Moisture content: ≤ 0.5 %. Solubility: ~ 1.2 g per 100 g water at 25°C (for tablet/powder form) for some specs. Appearance: White solid tablet form. Packaging example: Tablets weighing 200 g, packaged e.g. plastic drums or tubes (for bulk supply).Common uses: Swimming pool disinfection, algae/bacteria control, water treatment. & Storage in Drum with Closed Cover as per Directed By Engineer in -Charge |
| 38 | Providing, Supplying of Chlorine Granules Consisting of TCCA 90 Chlorine Granules Trichloroisocyanuric Acid (TCCA) 90% Granules – 5 8 mesh (also called “TCCA 90 Chlorine Granular 5 8 mesh”)Chemical name / formula: C₃N₃O₃Cl₃ CAS number: 87 90 1 Available (active) chlorine content: ≥ 90% Moisture content: ≤ 0.5% pH of a 1% aqueous solution: ~ 2.6 3.3 Solubility in water (approx): ~ 1.2 g per 100 g water at 25 °C Granule size / mesh size: 5 8 mesh for this version; (Other mesh options also available) Appearance: White granules (or crystalline granules) Typical packaging: e.g., 50 kg drums or carboys in some markets. Uses: Swimming pool / water treatment disinfectant, algicide & bactericide, especially for pool water sanitisation.50kg Drum with Cover & Store as per Directed By Engineer in -Charge. |
| 39 | Providing, Supplying of Swim ring Consisting of Swim ring Big size Size: Large diameter for adults / “big” sizeMaterial: Durable PVC or vinyl (inflatable pool‑ring standard)Intended use: One‑person float ring for pool leisure/floating Inflation: Standard valve; portable and inflatable/deflatable Colour/Finish: design as per Directed By Engineer in -Charge. |
| 40 | Providing, Supplying & Installation of Wall Mount LED Light 7 W/12V Consisting of Warm White Under water LED Light Wall Mount 7W/12V Supply voltage: 12 V (likely low‑voltage DC/AC) Mounting type: Wall‑mounted fixture Intended use: Likely for outdoor/architectural lighting (pool area, facade) Body & optics: Typical low‑voltage wall fixture would have corrosion‑resistant body (aluminium or powder‑coated), suitable for wet/humid environment Colour / finish: Likely white finish (or white housing) Goal: To provide low‑voltage illumination with modest wattage, safe for pool surrounds with complete installation as per Directed By Engineer in -Charge (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 41 | Providing, Supplying & Installation of Transformer as per Bellow Specification Consisting of Astral T1302 Transformer 300W/12V Power Supply Power rating: 300 VA / 300 W (for example the 300 VA version of Astral’s transformer range) Primary (input) voltage: 230 V AC (single-phase mains) Secondary (output) voltage: 12 V AC (for pool lighting / underwater lights) Protection / standards: Conforms to safety standard EN 61558 (or UNE EN 61558 2 6) for “safety transformers” (for pool lighting) Installation environment: Versions exist in IP20 rated housing for general use. There are also protective housings rated IP65 for more exposed or wet locations. Max distance from transformer to light: Up to ~ 40 m between transformer and underwater lamp (in the IP20 version) Use case: Designed for underwater pool lighting systems (12 V lighting) with one or more lights whose total power ≤ 300 W complete installation as per Directed By Engineer in -Charge (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 42 | Providing, Supplying & Installation of Connection Box as per Bellow Specification Consisting of Connection Box Type : Pool equipment connection/junction box (for wiring lights, pumps, or sensors) Enclosure Material: Likely durable plastic or fibreglass (pool area rated) with corrosion & moisture resistance Cable Entries: Multiple knock outs or gland ports for supply cables and equipment leads Voltage Rating: Suitable for standard pool lighting/control voltages (e.g., 230 V AC or 12 V/24 V low voltage, depending on usage) Protection: Should be rated IP55 or higher for wet pool equipment; offers protection against water spray/splash Mounting: Wall mountable enclosure with removable lid and gasket seal for wiring access Terminals: Internal screw type connection terminals for equipment wiring and grounding/earthing Cover: Transparent or opaque locking cover for visual check without opening, providing safety & access control complete installation as per Directed By Engineer in -Charge (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 43 | Providing, Supplying & Installation of Maintenance Trolley Kit as per Bellow Specification Consisting of Platform Trolley Plastic 300kg Platform Fold able With Mobile Filtration Unit Load capacity: 300 kg (safe working load) Platform material: Durable impact resistant plastic (e.g., high impact moulded plastic or polypropylene copolymer) with anti slip textured surface. Platform size: Typical approx 900 mm × 600 mm (L × W) for 300kg models. Overall height: Commonly around ~875 900 mm including handle. Ground clearance: Example ~145 mm clearance under platform for ease of movement. Wheel configuration: 4 wheels total — typically 2 fixed (front) + 2 swivel (under handle) for manoeuvrability. Wheel material: Often TPR (thermoplastic rubber) or PU (polyurethane) wheels for smooth & quiet movement. Example: 127 mm diameter TPR wheels. Weight of trolley: Example models around 11 13 kg (for plastic platform) when empty. Use environment: Indoor/warehouse, retail, commercial material handling; resistant to rust/corrosion given plastic platform. with complete installation as per Directed By Engineer in -Charge (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 44 | Providing, Supplying & Installation of Filtration Pump as per Bellow Specification Consisting of Filtration Pump 0.75 HP/0.55KW, Motor power: 0.75 HP (≈ 0.55 kW) — single phase version. Voltage: ~ 220 240 V, 50 Hz (for Indian market version) Maximum flow: ~ 15.9 m³/h (≈ 265 L/min) for this size in this brand range. • Intended for: Swimming pool circulation/filtering applications.Typical build: Pool pump housing, with pre filter basket, thermal protection motor. complete installation as per Directed By Engineer in -Charge (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 45 | Providing, Supplying & Installation of Sand Filter as per Below Specification Consisting of Sand Filter Tank diameter: 525 mm (≈ 21″) (as listed for “525 mm Swimming Pool Sand Filter – BlueWave 525 mm Dia” in India) Type: Laminated (fibreglass reinforced / bobbin wound FRP) sand filter for swimming pool application (non corrosive) Maximum working pressure: ~ 2.5 bar / 36 psi (common for this style of laminated sand filter) Maximum water temperature: ~ 50 °C (typical for FRP laminated pool filters) Filtration media size required: Silica sand around 0.5 0.8 mm suggested in comparable product specs Valve type: Top mounted multiport valve (6 way) typical for this size of pool filter. Material: Fibreglass reinforced polyester tank / FRP construction — ensures corrosion resistance. Application: Designed for swimming pool, spa, jacuzzi, artificial water bodies.with complete installation as per Directed By Engineer in -Charge (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 46 | Providing, Supplying & Installation of Vac Hose Sec Eva as per Below Specification Consisting of Vac Hose Sec Eva 1 Mtr Size / Diameter: 38 mm (≈ 1½″) internal diameter Length: 1 metre per section (sectional hose) Material: EVA (Ethylene Vinyl Acetate) with spiral helix reinforcement — gives good flexibility, is crush resistant and designed for pool vacuum/suction applications. Couplings: Comes with male and female cuff link ends to connect hose segments and interface with vacuum head/skimmer. Typical features: UV resistant, chemical (chlorine) resistant, flexible for pool usage, good flow characteristics. (General EVA hose spec) Application: Used for swimming pool vacuuming / suction cleaning, particularly manual vacuum heads attached to telescopic poles, connecting to the skimmer or suction point. complete installation as per Directed By Engineer in -Charge (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 47 | Providing, Supplying & Installation of Hose Adapter as per Below Specification Consisting of Hose Adapter Type: Hose adapter / connector (pool cleaning equipment) Material: Plastic (as listed) Colour: White Dimensions (approx): Width ~ 5 cm, Length ~ 10 cm, Weight ~ 40 g Purpose: Allows adaptation/connect of hoses to other fittings (pool vacuum or suction systems) Compatibility: Appears designed for use with pool cleaning hoses and accessories complete installation as per Directed By Engineer in -Charge (Make & Model as Per Selection of Consultant or Selection of Higher Authority) |
| 48 | Providing, Supplying of White Silica Sand Size - 0.5mm-0.8mm and gravel, Grain size: 0.5 mm to 0.8 mm (some specifications allow ~0.4–0.8 mm) for pool sand filters. Chemical composition: High purity silica (SiO₂) typically ≥ 95 99% purity. • Specific gravity: ~ 2.65 (for pure silica sand) Bulk density (approx): ~ 1.6 kg/L (or ~1600 kg/m³) for washed, graded sand.Hardness / wear resistance: Mohs hardness ~6 7; low acid solubility for durability in filter use.Properly graded sand ensures good flow/filtration and minimal channelling.with complete Stored in Bags as per Directed. |
| 49 | Sauna Bath & Steam Room Providing, Supplying & Installation of Sauna Cabin Consisting of One Side Wooden Paneling on a Concrete wall with Fully Insulated with Glass wool Stacked in Aluminium Foil Supported By Iron Mesh with complete installation, as per Directed By Engineer in -Charge (Sauna Cabin Size As Per Drawing) Also including Wooden Door, Wooden Floor etc with Loading,Unloading,Necessary Labour, Tools, Hardware Etc |
| 50 | Providing, Supplying & Installation of Sauna Cabin Consisting of Two Side Wooden Paneling on Concrete wall with Fully Insulated with Glass wool Stacked in Aluminium Foil Supported By Iron Mesh with complete installation as per Directed By Engineer in -Charge (Sauna Cabin Size As Per Drawing) Also including 12mm thk Tempered Glass Door. with Loading,Unloading,Necessary Labour, Tools, Hardware Etc |
| 51 | Providing, Supplying of Sauna Cabins Accessories For All Sauna Cabin Like Bulb,Hover,Glass,Sand Meter, Sauna Prevention Lamp, Wooden Bucket,with Laddle, Sauna Temperature meter etc with complete installation as per Directed By Engineer in -Charge including All Necessary Labour, Tools, Hardware Etc |
| 52 | Providing, Supplying of Sauna Cabins Benches made of wood with rounded edges for comfort and may include contoured backrests. as per Directed By Engineer in -Charge including All Necessary Labour, Tools, Hardware Etc |
| 53 | Providing, Supplying & Installation of Sauna Heater With Digital Touch Pad - Black 27KW with complete installation with required All Necessary Hardware, Electrical Wiring, Control Switches etc as per Directed By Engineer in -Charge including All Loading,Unloading, Labour, Tools,Etc. |
| 54 | Providing, Supplying & Installation of Steam Room as per Bellow Specification Consisting of 27KW Steam Generator, also Including 1.2mm Thk. SS 304 Stainless Steel Tank with Magnetic Filter, 1mm thk SS 316 Heating Elements Scale, Resistant Water level Controller, Auto Steam Drain, Safety Valve, Over Heating Temperature Protection, Light Provision with complete installation with required All Necessary Hardware, Electrical Wiring, Control Switches etc as per Directed By Engineer in -Charge including All Loading,Unloading, Labour, Tools,Etc. |
| 55 | Providing, Supplying & Installation of Steam Digital Touch Pad (Black) with complete installation & required All Necessary Hardware, Electrical Wiring, Control Switches etc as per Directed By Engineer in -Charge including All Loading,Unloading, Labour, Tools,Etc. |
| 56 | Bedminton & Squash Court Floor Providing, Supplying & Installation of Badminton court Wooden Sport Flooring System for indoor Badminton court as per Bellow Specification. Sports wooden Flooring : Wood Sport Flooring With 21mm Mix Grade Teak 55 to 85mm Wide & in Random length in tongue & groove shape. The Edge of the Boards will have a Finger lock groove and the bottom side with air pass groove and treated with Special anti termite and water resistant lacquer.The Under Frame: Pine wood sleeper sub floor of 70mm to 45mm treated with anti termite solution & Fixed on the Bottom with 19mm the EPDM Rubber Pad / 10mm EPDM Rubber Pads Stapled through the Two Wings at 350mm x350mm Installation : IPS Sub floor Treated With a vapour barrier to be placed on the leveled Existing IPS sub- floor Before Laying the under frame.The Runners having air cushion pads to be placed on the vapour barrier in perfect Level at 350mm in 1 direction. The surface board to be screwed to the runner through the tongue only and will lock the screwed tongue by the groove of adjoining board. Ends of the boards will be locked by inserting the wooden fingers through the edge grooves and fixed with suitable adhesive. The expansion of 12-15 mm will be left open between the wooden flooring and the surrounding tiled area/ walls. Finishing : After Installation the floor will be machine sanded in uniform level & Finished with Imported, Primer & Imported Polish,Rate including for Game line Marking to be Carried Out in required Colour before applying The Finish Coat.complete installation with required All Necessary Accessory Hardware,Loading Unloading,Transportation, Labour, Tools etc. Complete as per Directed By Engineer in -Charge |
| 57 | Providing, Supplying & Installation of Squash Court Flooring Consisting of Wooden Flooring System for indoor Squash Court as per Bellow Specification. wooden Flooring : Wood Sport Flooring With 21mm Mix Grade Teak The Edge of the Boards will have a Finger lock groove and the bottom side with air pass groove and treated with Special anti termite and water resistant lacquer.The Under Frame: Pine wood sleeper sub floor of 70mm to 45mm treated with anti termite solution & Fixed on the Bottom with 19mm the EPDM Rubber Pad Stapled through the Two Wings Installation : IPS Sub floor Treated With a vapour barrier to be placed on the leveled Existing IPS sub- floor Before Laying the under frame.The Runners having air cushion pads to be placed on the vapour barrier in perfect Level at 350mm in 1 direction. The surface board to be screwed to the runner through the tongue only and will lock the screwed tongue by the groove of adjoining board. Ends of the boards will be locked by inserting the wooden fingers through the edge grooves and fixed with suitable adhesive. The expansion of 12-15 mm will be left open between the wooden flooring and the surrounding tiled area/ walls. Finishing : After Installation the floor will be machine sanded in uniform level & Finished with Imported, Primer & Imported Polish,Rate including for Game line Marking to be Carried Out in required Colour before applying The Finish Coat.complete installation with required All Necessary Accessory Hardware,Loading Unloading,Transportation, Labour, Tools etc. Complete as per Directed By Engineer in -Charge |
| 58 | Providing, Supplying & Applying of Hard Plaster 3 to 4mm Thick on playing area (Squash Court) of all 3 walls to ensure it doesn't break and the ball bounce is as per WSF requirement, Work done with Cleaning the surface area to be treated with high pressure water jet ,removal of loose particles by wire brush, & Applying of Hard Plaster slurry self curing system - Brush coat in three layers with in 3-4 mm thickness after proper cleaning of surface Complete as per direction of Engineer-in-charge The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions etc complete with required All Necessary Loading Unloading,Transportation, Labour, Tools etc. Complete as per Directed By Engineer in -Charge |
| 59 | Providing, Supplying & Fixing of Sound Board for a squash court. Work include a material of galvanized iron (GI) for a metal sound board & Top wood Patti for soundproofing applications. The material must not deflect the ball and is typically at least 200 mm deep. The rate includes with complete All Necessary Labour, Material,Hardware Loading Unloading,Transportation, Tools etc. Complete as per Directed By Engineer in -Charge |
| 60 | Providing, Supplying & Fixing of Glass Back wall for Squash Court ( indoor) consist of specializing in premium-quality glass wall systems for squash courts. glass back wall systems are designed to provide a seamless combination of strength, transparency, and modern aesthetics. Made from high-impact toughened glass, these walls ensure superior durability, allowing them to withstand powerful shots while maintaining excellent visibility for players and spectators. squash court back wall glass system is engineered to match international standards, The tempered glass panels are carefully installed using advanced fittings, ensuring stability, safety, and long-lasting performance. With a smooth surface and precision alignment, glass back walls provide accurate ball rebound, maintaining the integrity of the game. & Easy to maintain and resistant to scratches, moisture, and impact.The rate includes with complete with Glass wall fittings, Labour, Material,Hardware Loading Unloading,Transportation, etc. Complete as per Directed By Engineer in -Charge |
| 61 | Interior Furnishing work Providing and fixing Armstrong (CLASSIC LITE RH 99 White) (Silhautte grid) 16mm false ceiling system manufactured by Armstrong using hot dipped galvanized steel section, rotary stitched main tee of size 15mm x 45 mm web height, having 0.36 mm gauge at every 600 mm centre to centre maximum and rotary stitched cross tee of size 15 mm x 45 mm, having 0.33 mm gauge at every 600 mm. c/c. and wall angle of size 19 x 19 mm., having 0.35 mm gauge fixed to the periphery of the wall. The above grid is suspended at every 600mm c/c. in both directions using Aluminium Squre Pipe/ Cleat Hanging from Roof Truss Member(any length) laying CLASSIC LITE RH 99 ceiling tiles with Silhautte grid manufactured by Armstrong , having Humidity Resistance of 99%, RH and size 600mmx600mmx16mm over the formed grid complete. including Light fixtures cutting gala in ceiling. & also including Scaffolding & Working Platform for any height) |
| 62 | Providing and fixing Armstrong (CLASSIC LITE RH 99 Black) (Silhautte grid) 16mm false ceiling system manufactured by Armstrong using hot dipped galvanized steel section, rotary stitched main tee of size 15mm x 45 mm web height, having 0.36 mm gauge at every 600 mm centre to centre maximum and rotary stitched cross tee of size 15 mm x 45 mm, having 0.33 mm gauge at every 600 mm. c/c. and wall angle of size 19 x 19 mm., having 0.35 mm gauge fixed to the periphery of the wall. The above grid is suspended at every 600mm c/c. in both directions using Aluminium Squre Pipe/ Cleat Hanging from Roof Truss Member(any length) laying CLASSIC LITE RH 99 ceiling tiles with Silhautte grid manufactured by Armstrong , having Humidity Resistance of 99%, RH and size 600mmx600mmx16mm over the formed grid complete. including Light fixtures cutting gala in ceiling. & also including Scaffolding & Working Platform for any height) |
| 63 | Providing & Fixing of Veneer Finished Wooden Ceiling Making from 12 mm thick plywood (IS 710) & Teak wood frame work as per drawing & instruction of EIC/architect & approved sample .Ceiling finish with 12mm Plywood with 4mm MDF board and 4mm thk veneer with melamine polish finish. Plywood shall be fixed with required Frame work and ply frame work with all necessary accessories & Hardware , Labour, tools , scafollding etc. Rate shall include cost of making of all cutouts for light fixtures, gadgets,pelmets, grooves,and also provide support/template where ever required The rate shall be in sq.mt for all floors and at all heights including all costs the sample mock of 5 Sqm minimum of the frame work and ceiling) shall be approved from client/architect.5mm Groove shall be provided at the junction of the false ceiling & the wall. The rate shall be in sq m for all floors and at all heights ,Off sets whether hollow or solid in the ceilings including all costs. etc. completed as per as per drawing & instruction of Architect and Engineer-In-charge. |
| 64 | Providing & Fixing of Laminate Finished Wooden Ceiling Making from 12 mm thick plywood (IS 710) & Teak wood frame work as per drawing & instruction of EIC/architect & approved sample .Ceiling finish with 12mm Plywood with 4mm MDF board and 1mm thk Laminate As per Approved Shade. Plywood shall be fixed with required Frame work and ply frame work with all necessary accessories & Hardware, & Hardware , Labour, tools , scafollding etc. Rate shall include cost of making of all cutouts for light fixtures, gadgets,pelmets, grooves,and also provide support/template where ever required The rate shall be in sq.mt for all floors and at all heights including all costs the sample mock of 5 Sqm minimum of the frame work and ceiling) shall be approved from client/architect.5mm Groove shall be provided at the junction of the false ceiling & the wall. The rate shall be in sq m for all floors and at all heights ,Off sets whether hollow or solid in the ceilings including all costs. etc. completed as per as per drawing & instruction of Architect and Engineer-In-charge. |
| 65 | Providing, Fixing,and Commissioning de mountable Stretch Fabric Ceiling PVC Base with White / or Coloured Translucent fabric on self Supporting PVC Frame Profile , Fabric translucent ratio is 75% , Fabric Thickness is 0.18mm to 0.20mm , A proprietary semi rigid PVC harpoon is welded on the periphery of the PVC ceiling membrane and light box should be sealed in a way it should be dust free. Ensure all services viz painting including other interior finishing works should have been completed before its installation. with led aluminium base bar led light of osaram led lens 24 watt system with installation including scaffolding and staging complete in all respects and to the entire satisfaction of Architects and Engineer-in-Charge. |
| 66 | Providing & fixing of Fluted Panel Cladding to consist of 26mm thk Fluted Panel (WPC) or Teak wood Pattern fixed on Backing of 12mm Plywood with required ply wood frame work with Melamine Polished as per Sujested by Engineer -in charge & border seal to teak wood beading patty with polishing on edge at wall surfaces,as per required & suggested Area. Cost including for All necessary hardware & polishing work complete as per Directed by Engg- in - charge. |
| 67 | Providing & fixing of Glass Brick wall consist of 190mm x 190mm x 80mm thk Glass Brick with required Leveled surfaces & It shall have the required flat surfaces and suitable size of wall, column etc Making sure that no fasteners stick out. Fixing the glass brick frame to the bottom center and sides with a generous bead of silicone adhesive at the top of the first block level, apply silicone to the exposed vertical side of the block,Place a vertical strip against the exposed silicone, repeating this process for the first layer. Place a continuous bead of silicone along the weld of each glass block. Place a horizontal separate strip in the slot provided in the side frame and lock the glass blocks in place.work Complete with neat & clean Surfaces on both side of wall including all Labour Material, tools, Scafolding etc.The rate shall be in Sq.Mt. for all floors and at all heights ,completed as per as per drawing & instruction of Architect and Engineer-In-charge. |
| 68 | Providing & fixing of Full height Storage Cabinet with Profile Glass Shutter (2600 mm ht. & depth 425 or as required) Cabinet made from 18mm th. Marine ply finished with 1mm th Approved Laminate from out side & inside of storage 18mm th. ply with 1mm thk Laminate & Shutter Making with Aluminium Profile Frame With 6mm Clear Glass with Required Frame work as per drawing & shutter operated on auto closing hinges, The storage shall have suitable size edge teak wood beading or The bottom of the storage unit to be provided above 18 mm Plywood skirting of skirting height. The cost shall be inclusive of all locks, SS tower bolts, handles, SS hinges, magnetic catchers and all hardware as per direction /schedule of interiors, furniture finishes. The storage shall be inside finished with 1 mm thk laminate of approved shade and All exposed edges to be finished withLaminate & Cabinets will have individual locking arrangement, & with necessary hardware etc Complete as shown in the drawing & design or as directed by Egg-in-charge |
| 69 | Providing and fixing of 8mm thick AC-4( average 4550 cycles) Domestic Extra series Laminate wooden flooring with Titan X Coating, impact resistance 9N, and resistance to cigarette burn with a rating of 4 (EN 438-2.05) material should be installed on Pergo combi foam and polythene,complete in all respects and the entire satisfaction of Architect and Engineer-in-charge.(Make Pergo , Welspun or Equalant Make as per instruction of Architect and Engineer-In-charge. |
| 70 | Providing and fixing of Laminate Wooden Flooring Skirting and beeding patti as per manufacturer's specificatons with ,complete in all respects and the entire satisfaction of Architect and Engineer-in-charge.(Make Pergo ,Welspun or Equalant Make as per instruction of Architect and Engineer-In-charge. |
| 71 | Loose Furniture Providing ,Supplying and fixing of Factory made Modular furniture as per below specification including erection at site. Linear Sharing Workstation System 1200mm 600mm x 1100mm Ht Sharing Cluster (Library) : Table Top : 25mm thk. Pre laminated Particle Board with 2mm PVC Edge lipping on all exposed edges, Table top at 750mm height from floor level. Support: End Legs: MS powder coated legs Intermediate Legs: MS powder coated 60X40mm legs and supporting MS cross beams Wire Management : 250mm Ht Raceway with 65mm Dia Wire Manager Grommet,Vertical Raceway with built in separator for power and data of size 250H X 70mm thick with provision to mount switches and sockets on laminate facia with Vertical Wire Entry cover for wire uptake from floor to raceway with 65mm Dia Wire Manager Grommet. Main Screen : 8mm thic Glass Screen Mounted on stud 1050X350Ht Passage Side Modesty : Plb Modesty 450 Ht (Make & System is as Per Selection of Architect Or Selection Of Higher Authority) |
| 72 | Providing,Supplying and fixing of Factory made Modular furniture as per below specification including erection at site. Linear Non Sharing Workstation System 1200mm 600mm x 1100mm Ht : Table Top : 25mm thk. Pre laminated Particle Board with 2mm PVC Edge lipping on all exposed edges, Table top at 750mm height from floor level. Support: End Legs: MS powder coated legs Intermediate Legs: MS powder coated 60 x 40mm legs and supporting MS cross beams Wire Management : 250mm Ht Raceway with 65mm Dia Wire Manager Grommet,Vertical Raceway with built in separator for power and data of size 250H x 70mm thick with provision to mount switches and sockets on laminate facia with Vertical Wire Entry cover for wire uptake from floor to raceway with 65mm Dia Wire Manager Grommet. (Make & System is as Per Selection of Architect Or Selection Of Higher Authority) |
| 73 | Providing,Supplying and fixing of Factory made Chair as per below specification including erection at site. Library Table Chair Consist of Medium PP (Black) Mesh chair with fixed Arm,powder Coated 4 Legs,Fabric Upholstered Cushion Seat Seat : Fabric (Black, Grey, Red, Blue) as per Directed (Make is as Per Selection of Architect Or Selection Of Higher Authority) |
| 74 | Providing ,Supplying and fixing of Factory made Single seater sofa as per below specification including Installed at site.Consist of Lounge single Seater sofa with powder Coated 4 Legs,Fabric /Leatherette Upholstered Cushion Fabric (Black, Grey, Red, Blue) as per Directed (Make is as Per Selection of Architect Or Selection Of Higher Authority) |
| 75 | Providing ,Supplying and fixing of Factory made Center Table as per below specification including erection at site. Size 600 x 600 x 450 mm HT. Solid wood structure as per Directed (Make is as Per Selection of Architect Or Selection Of Higher Authority) |
| 76 | Providing ,Supplying and fixing of Factory made Modular furniture as per below specification including erection at site. Library Rack Open Book shelf Consist of Double Side Stand-Alone-1095 W X 700D X 1950H 1050+900+900+900+900 =4695 Upright - MS 40 x 40 x 1.6 Tube.Side Profile - MS Powder coated metal profile of 1.6mm with Acrylic pouch. Band : Made of MS Powder coated metal 1.6mm,Shelves - Made of MS powder coated metal 1.2mm, supported with brackets. Back Panel - Made of MS Powder coated metal 0.8mm.Top panel , Side Panel & Bottom Panel - Made of 18mm thk PLT. (Make & System is as Per Selection of Architect Or Selection Of Higher Authority) |
| 77 | Providing ,Supplying and fixing of Factory made Modular furniture as per below specification including erection at site. Magazine Rack Size 760w x 430D x1000mm ht Complete Boady Make from 18mm Thick Particle Board with 2 mm PVC Edge band.(Make & System is as Per Selection of Architect Or Selection Of Higher Authority) |
| 78 | Providing ,Supplying and fixing of Factory made Moduler furniture as per below specification including erection at site. Cafe Table Four Seater (1050mm Dia x 750mm) Table Top : 25 mm thk. Prelaminated Particle Board with 2mm PVC Edge band on all side. Table top at 750 MM height from floor level. MS Powdercoated understructure.(Make is as Per Selection of Architect Or Selection Of Higher Authority) |
| 79 | Providing ,Supplying and fixing of Factory made Chair as per below specification including erection at site. Cafe Chair PP Shell with Metal Powder Coated Legs.(Make is as Per Selection of Architect Or Selection Of Higher Authority) |
| 80 | Providing ,Supplying of Out Door Lounger with cushion with Adjustable Back Rest Size 78'' x 27'' x 12'' (Total length 78’’ x width 27’’ x Maximum Height 31’’, Length,of backrest 30’’ ,Seat Length 45’’ , seat width 24’’ Seat Height 15”) or As per Directed Lounger Made From Solid Teak wood water & weather resistant,Elegant & Modern Look As per Image with Adjustable back rest with Upholstered Cushion Seat, 100% polyester Cover Foam Cotton fabric Material ,Without Arms,All Wood Members are Smooth polishing with Melamine Polish. Polish Shade as per Selection of Consultant or Selection of Higher Authority) |
| 81 | Providing ,Supplying of Lounger Side Table 15'' x15'' x18'' Fold able As per Directed by Engineer Incharge. Side table Made from Teak wood Batten with Folding system as per Image all Teak member smooth with Melamine polish Selection of Consultant or Selection of Higher Authority) |
| 82 | Providing Supplying of Folding Outdoor Decorative Umbrella with Chairs & Table set (4 chairs set) include 4-piece patio set is composed of a glass-top table, four folding chairs, and an umbrella All chairs have a powder-coated steel frame and sling fabric high backrest, as well as easy-fold capability for quick storage and transportation ,Table also features a durable powder-coated steel frame and an easy-to-clean water wave glass top tabletop, pre-cut for the umbrella to slot in The steel and polyester fabric construction provides great protection against outdoor weather (Colour as per Selection of Consultant or Selection of Higher Authority) |
| 83 | Providing and Fixing GRC Screens having compressive strength of 35-55 MPA and Flexural Strength of 6-16 MPA as per approved design, colour, Finish by Architect and Engineer in-Charge including Packing, Transporting, Unloading, fixing at Site etc. complet |
| 84 | Providing and Fixing GRC Base Ring as per approved design, colour, Finish by Architect and Engineer in-Charge including Packing, Transporting, Unloading, fixing at Site etc. complet |
| 85 | Providing and Fixing GRC Cornice as per approved design, colour, Finish by Architect and Engineer in-Charge including Packing, Transporting, Unloading, fixing at Site etc. complet |
| 86 | Providing, Fabricating and fixing Structural Steel in required pattern/ design using necessary Structural Steel Sections as per detailed design/ drawings/ instructions including cutting, bending, jointing, connecting, welding and / bolting and / riveting, fabricating and erecting in position etc. complete using required Lifting arrangements including Cranes, etc. for all levels as directed including all necessary fixtures, fastening and one coat of primer and two coats of mat finished oil painting etc. complete. |
| 87 | Providing, Supplying and Installing False Ceiling of make Aluminium linear 84C Plain Panels with Wooden Finish Powder Coated having Square edge panels, 84 mm wide x 15 mm deep x length up to 5 mtr. With 25mm recess flange formed out of 0.50 mm thick (TCT) aluminium alloy (AA) 8011-H3 fixed on carriers having 28 mm wide at the bottom x 43 mm deep formed out of 0.91mm thick alumnium sheet stove enameled black with protruding ears to hold the panels in a module of 100 mm.and supporting structure painted with Spray Paint.The carrier shall be suspended from slab by 4 mm dial galvanized rod with special height adjustment powder coated clips made out of spring steel at maximum 1.2 to 1.5 mtr. Centre to centre. The 4mm dia galvanized rod shall be fixed to slab by forming one end “J” shape with roll inserts. The edge profile formed out of Aluminium Sheet of the size 18 mm x 20 mm shall be fixed on the perimeter of the walls |
| 88 | Providing, laying, testing & commissioning of 25 mm diameter 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : |
| 89 | Providing, laying, testing & commissioning of 32 mm diameter 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : |
| 90 | Providing, laying, testing & commissioning of 40 mm diameter 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : |
| 91 | Providing, laying, testing & commissioning of 50 mm diameter 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : |
| 92 | Providing, laying, testing & commissioning of 65 mm diameter 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : |
| 93 | Providing, laying, testing & commissioning of 80 mm diameter 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : |
| 94 | Providing, laying, testing & commissioning of 100 mm diameter 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required |
| 95 | Providing and fixing 80 mm dia cast iron butterfly valve complete with epoxy coated disc, carbon steel shaft and lever actuator including flanges and nut bolts etc complete as per I.S 13095 of PN16 rating. for isolation |
| 96 | Providing and fixing 100 mm dia cast iron butterfly valve complete with epoxy coated disc, carbon steel shaft and lever actuator including flanges and nut bolts etc complete as per I.S 13095 of PN16 rating. for isolation |
| 97 | Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : |
| 98 | Supplying and fixing first-aid 30 meter long Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585. 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. |
| 99 | Supplying and fixing first-aid 40 meter long Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585. 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. |
| 100 | Supplying and fixing Gun Metal 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : |
| 101 | Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required as per approved make. |
| 102 | Supplying and fixing of 2-way fire brigade connection to static tank (Draw out connection) of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : |
| 103 | Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent Sprinkler |
| 104 | Supplying and fixing of Upright Sprinkler |
| 105 | SITC of Electrical driven main pump suitable for automatic operation and consisting of following ,completed in all aspects 2850lpmat 88m of head |
| 106 | SITC of Diesel engine driven main fire pump for automatic operation and consisting of following in all respects as required (Diesel Driven pump) |
| 107 | SITC of electrical driven pressurization pump suitable for automatic operations & Consisting of following compelete in all aspects as required Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
