|
| 1 | Civil work |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. All kinds of soilDSR 2023/2.6.1 |
| 3 | Earth work in filling in cartage upto 8 KmSR |
| 4 | Proving and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to planth leve: 1:4:8 (1 cement:4 coarse sand (zone-II) derivedfrom natural source : 8 graded stone aggregate 40 mm nominal size derivedd from natural sources) DSR 2023/4.1.8 |
| 5 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cumDSR 2023/5.33.1.1 |
| 6 | Centering and shuttering including strutting, propping etc. And removal of form for :Foundations, footings, bases of columns, etc. for mass concreteDSR 2023/5.9.1 |
| 7 | Steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. thermo-mechanically treated bars of grade fe-500D or more.DSR 2023/5.22.6 |
| 8 | Brick work with common burnt clay machine moulded modular bricks of class designation 12.5 in exposed brick work including making horizontal and vertical grooves 10 mm wide 12 mm deep complete in cement mortar 1:6 (1 cement : 6 coarse sand). From ground level upto plinth level DSR 2023/6.28.1 |
| 9 | 12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand) DSR 2023/13.1.1 |
| 10 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth Complete.DSR 2023/13.80 |
| 11 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)DSR 2023/13.47.1 |
| 12 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar worksDSR 2023/10.25.2 |
| 13 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new workDSR 2023/13.61.1 |
| 14 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured to calculate volume for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).DSR 2023/16.69 |
| 15 | Providing and laying factory made cobble shape paver block 80 mm thick, compressive strength >= M 30 steel mould compressive technology.SR |
| 16 | Providing and fixing of Sandstone Garden Bench (3 Seater, without armrest & backrest), in rectangular shape sitting platform of size 1500mm (Length) x 400mm (Width) with two legs of size 350mm (height) x 450mm (width) x150mm thickness with sitting height of 450mm, fabricated from natural sandstone, machine cut with smoothened edges, fine dressed finish, suitable for outdoor use in gardens/parks/government premises, bench is to be treated with special epoxy resign for waterproof coating so as to make surface glossy and whether proof, complete in all respects as per direction of Engineer-in-Charge.MR |
| 17 | Supply and installation of Steel bottom Loading Water dispenser with 02 taps capacity 80 litresMR |
| 18 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall20 mm nominal dia PipesDSR2023/18.7.2 |
| 19 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameterDSR 2023/12.41.2 |
| 20 | Electrical Work |
| 21 | Supply and fixing of 12 mtr High mast Pole of approved make with rising system, hot dip Galvanized inside & outside , having pole sheet thickness 4mm, top dia minimum150mm, bottom dia minimum 360mm, base plate 32mm thick, suitable for wind velocity as per IS 875 part 3 &.having no circumferential weld, with accessories for high mast such as head frame suitable for 6 luminaries & its control gear boxes,1 HP Power tool motor, 3 point suspension system with steel wire rope 6mm dia , double drum winch. Including making suitable Foundation as per manufacture drawing & site requirement along with foundation bolts, nuts, washers, anchor plates etc. Complete in all respect as per direction and satisfaction to the Engineer-in-charge. SOR2022/651 |
| 22 | Supply and fixing of factory wired integral LED flood lightluminaires with die cast aluminium housing built with dirver setsuitable for 170 to 180 Watt. Confirming to IP 66 protectioncomplete in all respect.CAT-AAASOR2022/1455 |
| 23 | Supply and burring of Safe Earthing Electrode T-19, (Hot Dip Galvanized), Length up to 3000mm, outer Dia 50 mm inner Dia 25 mm, terminal Dia 12mm, outer GI pipe of 16 swg and inner GI pipe of 12 swg with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity and one earthing lead of 25mm x3mm G.I. strip, upto switch board (from apron to switch board, the cost of G.I. strip will be extra) along with 30 cm square C.I. frame with hinged cover & masonry housing. Make: As approved in U.P. P.W.D., & C.P.R.I. CertifiedSOR2018/725B |
| 24 | Supply and Fixing Following capacity of automatic street light cubical control panel painted with anticorrosive alkali and acid proof paint consisting of time switch Tso 100 series with contactors, HRC fuses, isolating switch metering instrument & intrument box with CTs etc. in case of TPN, complete in all respect. SOR-2022 SI. No. 807 (f) (I) 40 A TPNSOR2022/807 |
| 25 | Supply and laying of aluminium conductor PVC insulated armoured served sheathed 4x16 sqmm cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc.SOR2022/501(i) |
| 26 | Supply, installation, testing and commissioning of factory-wired integral LED street light luminaire suitable for 30W to 36W, with-die-cast-aluminium housing, IP65 protection, controlled by solar system.-Backup: Minimum 12 hours autonomy per day. Warranty: 3 years comprehensive warranty on complete system including LED, battery, solar panel and controller.Components included: 3 meter MS pole with base plate & foundation bolts, solar PV panel of suitable rating, LiFePO4/Lithium battery with weatherproof enclosure, MPPT/PWM charge controller, interconnecting cables, junction box, earthing, and all accessories required for complete installation for Solar System. (excluding Foundation)MR |
| 27 | Supply and fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. The armouring of the cable shall be properly connected with the earth as per direction of Engineer-Incharge.16 sq. mm 4 coreSOR2022/503(i) |
| 28 | Supply and fixing of plain or pin type copper/Alluminium tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer16 sqmmSOR2022/504(D) |
| 29 | Horticulture |
| 30 | Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately)Holes 45 cm dia, and 45 cm deepDSR2025(H&L)/2.14.4 |
| 31 | Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 20 mmDSR2025(H&L)/2.4.1 |
| 32 | Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately)DSR2025(H&L)/2.8 |
| 33 | Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-chargeDSR2025(H&L)/2.9 |
| 34 | Filling mixture of earth and sludge or manure in the desired proportion in trenches, flooding with water and leveling (cost of supplying earth and sludge or manure and mixing excluded).DSR2025(H&L) |
| 35 | Providing and stacking Duranta Golden, having ht. 15 cm to 20 cm bushy shape with fresh and healthy leaves in 15 cm size of Earthen Pot / Plastic Pot and as per direction of the officer-in-charge.DSR2025(H&L)/2.20 |
| 36 | Providing, stacking and Displaying Travellers palm well developed with fresh & healthy foliage 210 cm to 240 cm ht specimen plant in 40 cm Cement Pot/ Plastic Pot and as per direction of the officer-in-charge.DSR2025(H&L)/6.12 |
| 37 | Providing, stacking and Displaying Areca Palm having ht. 1.80 m to 2.10 m with 8 to 10 suckers, well developed, fresh and healthy with lush green foliage in 30 cm size of Earthen pot / Plastic pot and as per direction of the officer-in-chargeDSR2025(H&L)/5.43 |
| 38 | Grassing with selection No. 1 Doob grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn, free from weeds and fit for mowing including supplying good earth, if needed (the grass and good earth shall be paid for separately). 2.10.1 In rows 5 cm apart in both directionsDSR2025(H&L)/3.17 |
| 39 | Plantation and reffilingDSR2025(H&L)/2.57.1 |
| 40 | Borewell |
| 41 | Boring/ drilling bore well of required dia for casing/ strainerpipe, by suitable method prescribed in IS : 2800 part I,including collecting sample from different starta, preparing and submitting equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer In charge, up to 90 meter depth below ground level. All type of soil Sanction Rate0-15 m BGL |
| 42 | Boring/ drilling bore well of required dia for casing/ strainerpipe, by suitable method prescribed in IS : 2800 part I,including collecting sample from different starta, preparing and submitting equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer In charge, up to 90 meter depth below ground level. All type of soil Sanction Rate15-30 m BGL |
| 43 | Boring/ drilling bore well of required dia for casing/ strainerpipe, by suitable method prescribed in IS : 2800 part I,including collecting sample from different starta, preparing and submitting equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer In charge, up to 90 meter depth below ground level. All type of soil Sanction Rate30-65 m BGL |
| 44 | Supply, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well casing (CM) pipe of required dia conforming to IS: 12818 including required hire and labour charges, fittings & accessories etc. all complete for all depths as per direction of Engineer in charge.100 mm nominal size dia |
| 45 | Supply, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818 including required hire and labour charges, fittings & accessories etc. all complete for all depths as per direction of Engineer in charge.100 mm nominal size dia |
| 46 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/casing pipe,removable as per requirement, all complete for bore well of: 100 mm dia. |
| 47 | Providing and fixing chlorinated Polyvinyl Chloride (CPVC) pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings this includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in charge. 40 mm nominal outer dia pipes. |
| 48 | Providing & Fixing M.S. clamp of required dia to the top of casing/ housing pipe of tube well as per IS 2800 part - 1 including necessary bolts & nuts of required size complete. 100 mm clamp. |
| 49 | Gravel packing in tube well construction in accordance with IS:4097 including providing gravel fine/ medium/ coarse in required grading & sizes as per actual requirement all complete as per direction of Engineer-in-charge. |
| 50 | Supply/ erection of 5 HP KSB/ Crompton or equalent submersible pump with motor including 15 sqm 3 core cable, (approx 45 meter length) including cost of steel rope& panel.=43081.8x15%=49544.07 |
| 51 | Children Play Apparatus |
| 52 | Roto Wave Slide 7 FT HT |
| 53 | Double Arc Swing |
| 54 | Animal MGR |
| 55 | Spring rider Duck |
| 56 | Spring rider Hopper |
| 57 | Multi Seater See Saw |
| 58 | Four seater MGR |
| 59 | Platform MGR |
| 60 | Bridge ladder Please Enable Macros to View BoQ information |
