|
| 1 | Dismantling the Existing damaged Brick work in Cement morter including all labour charges etc., complete |
| 2 | Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel,stoney earth and earth mixed with small size boulders SS.20B and Sand,silt or other loose soil, wet sand,or silt not under water, light black cotton soil, sandy loam ordinary soil and to full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering, ,and baling out water and cleaning and levelling the site etc.,complete 10 m3 |
| 3 | Plain Cement Concrete 1:4:8 (one cement four fine aggregates and Eight coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying water carrying with all leads of good water compacting and labour charges and all incidential charges such as water providing etc., complete as per standard specification |
| 4 | Brick work in cement mortar 1:5 mix using Fly Ash bricks of 230x110x70mm (8 3/4\\" x 41/4\\" x 23/4\\") including cost of materials and labour charges etc. as per std. specification - 1m3 |
| 5 | Plastering with cement mortar (1:5),12 mm ,thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications (S.I.306) |
| 6 | White washing two coats with freshly burnt shell lime white in colour in all floors including cost of lime and other materials brushes scaffolding charges etc.complete complying with standard specification and as directed. -100Sqm S.I.333 |
| 7 | Painting two coats for Exterior surface with approved Exterior Plastic Emulsion paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification. |
| 8 | Providing and fixing casement doors fabricated from un-plasticized polyvinyl chloride (uPVC) sections Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm. The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals.Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside.Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam. Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug |
| 9 | Supplying, fabricating and fixing in position of Alumi.Anod.natural colour matt finish door half glazed and half PLB board using 12 mm thick PLB board and 5.5 mm thick glazed door using rectangular Alu.Box section of following sizes for frame and shutter with necessary accessories such as rubber beading, Al. Clips, Best double action floor springs, Aluminium Handles on both sides,floor stopper,Tower bolt, Locks and glass including all materials, Labour, power consemption charges required for fabrication if necessary chipping, dismantling making necessary holes in RCC Coloums, Beams or Masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing etc.,complete. The Alumi. surface must be anodised with matt finish under electrically controlled condition in accordance with IS specification 1868 / 1962 of Anodic filthickness of not less than 15 Microns (Fifteen) for all sections. |
| 10 | Supplying and fixing in positon European Water Closet (Oriya type) of size 580 x 440mm colour glazed earthern ware of approved quality and brand with \\"P\\" or \\"S\\" trap conforming to BIS with crushed stone sandcushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two crushed stone sandand Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to CI soil pipes (including the cost of 100mm dia CI pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works). |
| 11 | Supplying and fixing in position Indian water closet of size 580 X 440mm, white glazed earthen ware of approved quality with 'P' trap or 'S' trap confirming to IS:2556 - Part XII with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 ( one part of lime, two parts of sand and five parts of brick jelly) 100mm thick and finishing the top to required slope and including giving necessary connection to cast iron soil pipes/ PVC pipes by dismandling brick masonry, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers. |
| 12 | Paving the floor with design Antiskirt ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured cement |
| 13 | Dadooing the Wall with Cement based hydrualically pressed Anti-Skid tiles (pattern design) 20 mm thick in cement mortar 1:2 - 20 mm thick & pointed with same colour of cement etc., complete as per standard specification |
| 14 | Plain Cement Concrete 1:2:4 (one cement, two Crushed Stone Sand (M- Sand) and four coarse aggregates) using 20mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges etc., complete as per standard specification |
| 15 | Wiring with 2 x 1.5 Sqmm. (22 / 0.3) PVC insulated SC unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with TW switch box inflush with wall with 5A FT switch covered with hylum sheet of 3mm thick with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC light point / fan point (for electronic regulator) (SD-19) |
| 16 | Supplyandfixingof4FeetLED18WFittingwithLED18Wtube(HigherEnd)completewithTWroundblockson wall or ceiling with PVC unsheathed FRLS Copper leads from terminals to the fitting SD 441 |
| 17 | Supply and Fixing of 1200 mm Ceiling fan includingn cost and conveyance of all materials and labour cherges etc complete.(SD-106) |
| 18 | Supply and fixing of 18W LED 3000K Square Type Recessed Fitting with LED M-1285 |
| 19 | Supplying and delivery of following Electrical items |
| 20 | 6Amps Switch |
| 21 | 6Amps Socket |
| 22 | 20Amps Switch |
| 23 | 20Amps Socket |
| 24 | 2 Pole MCP |
| 25 | Single Pole MCP |
| 26 | Supply and fixing of PVC Pipe and specials including cost and conveyance of standard specification |
| 27 | 25mm PVC pipe |
| 28 | 25mm PVC Elbow |
| 29 | 20mm Tap |
| 30 | 110mm PVC Pipe |
| 31 | 110mm PVC Tee |
| 32 | Supplying and fixing in position of RCC Pre cast slab 50mm thick including all cost and conveyance of all labour etc., complete |
| 33 | Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia \\"B\\" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works). |
| 34 | Supplying and fixing in position of steel iron grill work including all cost and conveyance etc., complete |
| 35 | Supplying and delivery of FRP transparent sheets 4mm Thickness M-2949 |
| 36 | Painting two coats for Exterior surface with approved Exterior Plastic Emulsion paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification. |
| 37 | Painting Old iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with Two coats of best approved first quality and colour of synthetic enamel paint in all floors etc., complete complying with standard specification and as directed by the departmental officers.(The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.) |
| 38 | Supplying and painting the walls with two coats of wall putty as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications and as directed by the departmental officers. (The wall putty shall be got approved by the Executive Engineer before use of work). |
| 39 | Supplying and laying Rubberised interlocking Paver block M40 grade Providing and laying of 63mm thick high strength type conforming IS 15658-2006 of rubberized interlocking paver lock in size of minimum compressive strength of 40N/mm2 in uniform shape of approved make to be laid in flurring bone pattern with sand cushion below the uniform shap of approved non skitting surface in the top and the rate including levelling the base preparation of pavers as sub base, sand cushion 150mm thick laying out of pavement cut the pieces to fix the edge vibring the pavers,sweeping tranporting loading unloading of laying paver block as per standard specification,. |
| 40 | Supplying and fixing in position of Kitchen Vessells including all cost of loading and unloading charges etc., complete |
| 41 | Silver bucket - No.8 |
| 42 | Silver bucket - No.10 |
| 43 | SS Water Drum |
| 44 | Water Mug |
| 45 | No.40 SS Spoon |
| 46 | SS 'D' mug for rise |
| 47 | Tumbler |
| 48 | SS Plate |
| 49 | 5Kg Silver Kunda |
| 50 | Basin Plate |
| 51 | Rise Thuduppu |
| 52 | Knife |
| 53 | Silver Muram |
| 54 | D' Kunda |
| 55 | Mini Plate |
| 56 | Silver Tray Small size |
| 57 | Silver Cup |
| 58 | Spoon |
| 59 | 25Kg Big size Aluminium Kunda |
| 60 | 10Kg Aluminium Kunda |
| 61 | 5Kg Aluminium Kunda |
| 62 | Aluminium Milk Kunda |
| 63 | 6 Lit Aluminium Kunda |
| 64 | Big size Basin |
| 65 | Small size Basin |
| 66 | Aluminium Plate |
| 67 | Vada satty |
| 68 | Aruval manai |
| 69 | Chinese Spoon1 |
| 70 | 20 Lit Dimond Cooker |
| 71 | Mixer Grinder |
| 72 | 105 Nos. Idly Pan |
| 73 | 25 Lit R.O. System |
| 74 | Double burner Stove |
| 75 | Repairs to the Old Stove (2Burner) set including all labour charges etc., Please Enable Macros to View BoQ information |
