|
| 1 | Providing & Installation of Hockey Goal Post, Techinical Table, Dugout , 9 Nos 7mtr high flag post, Cleaning and maintenance of Turf |
| 2 | Providing & Installation of Hockey Goal Post, Techinical Table, Dugout & 9 Nos 7mtr high flag postProviding & Installation of Made of Aluminium Rectangular pipe as per FIH Specifications with New Aluminium back boards for rubber flooring 4mm, Special steel rod made of 6mm SS for easily hanging the net. Size of Goal Post 12’ x 7’ (Movable) Easy moving on 2 double Co Polymer Wheels which are non-marking branded wheels to help protect floors. Use of high quality branded MRF Epoxy paint with Garware Tournament Net complete in all respects and as desired by Engineer-in-Charge. (Similar to Recently used in Junior Hockey World cup at chennai in 2025-26) |
| 3 | Providing & Installation of Bajaj – Size: Length-129 x Width- 89 x Height 8.59, Base made of 40mm x 40mm square MS pipe, Roof made of 50mm x 50mm heavy synthetic surfaces. 2.5mm polycarbonate sheet made by 100% virgin LEXAN material UV stabilized. Height of Tech Platform from Table Size :129 x 39, width 20=, Table covering three side with ACP sheet, Colour as per customer complete in all respects and as desired by Engineer-in-Charge. (Similar to Recently used in Junior Hockey World cup at chennai in 2025-26) |
| 4 | Providing & Installation of 20 seater Dugout top made of 2= x 2= square pipe and base made of 100mm x 50mm square heavy MS pipe with non-marking wheels for synthetic surfaces. 2.5mm polycarbonate sheet made by 100% virgin LEXAN material UV stabilized. Length: 249, Height: 79 complete in all respects and as desired by Engineer-in-Charge. (Similar to Recently used in Junior Hockey World cup at chennai in 2025-26) |
| 5 | Providing & Installation of 7mtr high flag post made of 75mm dia GI Pipe 3mm thick with pulley mechanism bolted on floor without cost of flag complete as per specification and as desired by Engineer-in-Charge |
| 6 | Construction of 2 Nos Camera Tower Plateform |
| 7 | Earth work in excavation in foundations, trenches etc. in all kinds of soil where pick jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation and subsequent filling around masonry in 15 cm. layers with compaction including disposal of all surplus soil as directed within a lead of 30 metres. |
| 8 | Cement Concrete 1:4:8 With stone aggregate 40mm gauge. mixing by mechanical means using concrete mixer volumetric type |
| 9 | Reinforced cement concrete M-25 mechanicaly batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centring and shuttering in foundation and plinth |
| 10 | Shuttering for faces of concrete foundations and foundation beam & plinth beam (vertical or battering) |
| 11 | Cold twisted deformed (Ribbed/ Tor Steel Bar/TMT) Bars Fe 500 grade as per IS 1786-2008, for R.C.C works, where not including in the complete rate of RCC including bending and placing in position complete |
| 12 | First class burnt brick work laid in cement sand mortar 1:6 in foundation and plinth. |
| 13 | Structural steel work in compound girders or Stanchions built up from two or more R.S. joists or channel section or plates & angles etc. including cutting and fixing all lattice bars, stiffeners, gusset plates, bolts, nuts, rivets, welding rod, etc. complete with flange plates, heads, sole plates, angle connections, etc. with hoisting and erecting in position |
| 14 | Applying priming coat with metal primer on new steel or iron work including preparation of surface. |
| 15 | Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade. |
| 16 | Providing and fixing polycarbonate sheet sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws with EPDM seal, and the joints shall be provided with aluminium strips at top and bottom as a seal complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. Pollycarbonate sheet Multiwalled 10mm thick |
| 17 | Providing and laying resilient vinyl sheet floor covering 2 mm thick, having a vinyl plastic wear layer with backing intended for use in light commercial and residential Players changing rooms |
| 18 | Dismantling of floor tiles at any floor of the building, laid in cement mortar including dismantling of cement concrete base and disposal of malba at a suitable place within a distance of 100 Mtrs of the complex complete in all respect. dismantling of broken granite stone tiles dismantling of broken kota stone tiles |
| 19 | Black Granite stone tiles 15mm to 20mm thick in skirting, risers of steps, dado walls and pillars laid in 12.5mm thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with neat cement slurry mixed with pigment to match the shade of stone, including rubbing and polishing including labour for fixing dowel pins and cramps. |
| 20 | Kota stone slab 20-25 mm thick flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : |
| 21 | Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular ctions/ appropriate z sections and other sections conforming to Is: 733 and IS : 1285 of Jindal, Hindalco, Mahavir or equivalent make approved by Engineer in Charge , fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC Plug/neoprene felt etc. aluminum sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, aluminum snap beading for glazing/paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-In- Charge. (Glazing and paneling to be paid for separately) : (b) For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and labour for fixing of fittings wherever required including the cost of PVC Plug / neoprene gasket required |
| 22 | Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in paneling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer-In-Charge. Prelaminated particle board with decorative lamination on Both side. |
| 23 | Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with PVC Plug/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminum snap beading shall be paid in basic item) (i) Float glass panes of 5 mm thickness |
| 24 | Providing Polyester Powder coating 50 micron any coloured specified to alumnum section of various sizes including carriage of material from market to workshop & workshop to site of work. |
| 25 | Cost of aluminum fittings complete for doors, windows such as tower bolts, handles,Stoppers and screw etc. for these fittings (Excluding sliding bolt) (ii) For shutter area above 0.50 sqm |
| 26 | Providing & fixing 9\\" stainless steel handles ISI marked on door & window frames complete in all respect as per the directions of Engineer-in-charge. |
| 27 | Providing & fixing 4\\" stainless steel handles ISI marked on door & window frames complete in all respect as per the directions of Engineer-in-charge. |
| 28 | Providing & fixing 4\\" stainless steel tower bolts ISI marked on door & window frames complete in all respect as per the directions of Engineer-in-charge. |
| 29 | Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : (A) 300mm x 16mm |
| 30 | Providing and fixing hydraulic door closer ISI mark with necessary screw etc. complete © I.S.I Designation Each III (size of door 851mm to 1000mm) |
| 31 | Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with PVC Plug/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminum snap beading shall be paid in basic item) |
| 32 | Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two or more coats to get required finish |
| 33 | Applying priming coat with cement primer in all shade on newly plastered or concrete exterior surface |
| 34 | Wall painting with plastic emulsion paint of approved brand and manufacturer to give an even shade (two or more coats) |
| 35 | Finishing walls with acrylic smooth exterior paint of required shade with two or more coats applied @ 1.67 litre/10Sqm over and including base coat of water proofing Cement Paint applied @ 2.20 Kg/10 Sqm |
| 36 | Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade. |
| 37 | Earth work in excavation in foundations trenches etc. in all kinds of soil where Pick-Jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil clear from the edge of excavation and subsequent filling around masonry in 15 cm, layers with compaction including disposal of all surplus soil as directed within lead of 30 metres. |
| 38 | Cement concrete 1:4:8 With stone aggregate 40mm gauge mixing by mechanical means using concrete mixer volumetric type |
| 39 | Precast Cement Concrete Kerb Providing and laying factory made rubber moulded smooth finish cement concrete Kerb M-20 grade 250mm high with bottom width 165mm and top width 115mm made over strong vibratory table and fixing with cement mortar 1:2 as per MORT&H specifications |
| 40 | Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade. |
| 41 | First class burnt brick laid in cement sand mortar 1:6 in foundation and plinth |
| 42 | 12.5mm thick cement plaster 1:4. |
| 43 | Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead. |
| 44 | Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceablematerial within 50 meters lead as directed by Engineer-in-charge |
| 45 | Providing and fixing mineral fibre false ceiling tiles at height upto 4 Mtr. of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflection > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main T. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of0.40 mm thick sheet, to be fixed to the wall with help ofplastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge. With 16 mm thick beveled tegular mineral fibre Anti-microbial false ceiling tile confirming to ISO 5 (class 100) specifications |
| 46 | Design supply & installation of suspended Spider Glazing system designed to withstand the wind pressure as per IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS-316 Grade Stainless steel Spider.& bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using fastener & anchor bolts, non star bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. |
| 47 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge |
| 48 | P/F of ACP Sheet 4 mm thick |
| 49 | Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes,M.S. tube challies, M.S.clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after .The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineerin- charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding.Note: - This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done. |
| 50 | Providing & Laying 60 mm thick factory made cement concrete interlocking Paving blocks of M-40 grade |
| 51 | Excavation in Soil (any type) using Hydraulic Excavator CK 90 with hydraulic excavator of 0.9 cum bucket capacity including cutting, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, including all lifts and combined lead upto 30m. |
| 52 | Cement concrete 1:4:8 with stone ballast 40 mm gauge in foundation |
| 53 | Providing and laying 60 mm thick factory made cement concrete interlocking Paving blocks of M-35 grade machine made rubber moulded smooth finish with strong vibratory process and approved size and design/ shape laid in Ordinary Grey Colour and pattern over and including 40 mm thick compacted bed of coarse sand, filling the joints with fine sand etc, all complete as per directions of Engineer-in- Charge. |
| 54 | Providing & Installation of Informatory, Safety Sinage & Emergency Exit as per Guidelines for Universal Accessibility |
| 55 | Providing & fixing of Informatory sign board single legged double sided Size 600x600mm non glared with retro reflective high intensity Microprismatic grade sheeting type-iv as per ASTM D4956-09 fixed over 4mm thick ACP sheeting having aluminium skin thickness of 0.25 to 0.3 mm on both sided and fixing the same with suitable epoxy base adhesive on back support frame of M.S hollow section 60x40x3.2 mm supported on a square M.S hollow steel section post 60x60x3.2mm conforming to IS code firmly fixed to ground in foundation concrete M-20 of size 0.45 x 0.45 x 0.60 M for vertical postcomplete in all respects, as per specification & as desired by Engineer-in-Charge (Confirming to Harmonised guidelines & standards for Universal accessiblity in India-2021 issued by Ministry of Housing and Urban Affairs Government of India) |
| 56 | Providing & fixing of Informatory sign board double sided hanging from ceiling Size 1371 x 952mm non glared with retro reflective high intensity Microprismatic grade sheeting type-iv as per ASTM D4956-09 fixed over 4mm thick ACP sheeting having aluminium skin thickness of 0.25 to 0.3 mm on both sided and fixing the same with suitable epoxy base adhesive on back support frame of 40x20x3.2 Stainless Steel supported on a square M.S hollow steel section post 40x40x3.2mm conforming to IS code firmly hanged from ceiling/beam by fixing with expandable fastners complete in all respects, as per specification & as desired by Engineer-in-Charge (Confirming to Harmonised guidelines & standards forUniversal accessiblity in India-2021 issued by Ministry of Housing and Urban Affairs Government of India) |
| 57 | Providing & fixing of Informatory sign board double sided hanging from ceiling Size 1371 x 634mm non glared with retro reflective high intensity Microprismatic grade sheeting type-iv as per ASTM D4956-09 fixed over 4mm thick ACP sheeting having aluminium skin thickness of 0.25 to 0.3 mm on both sided and fixing the same with suitable epoxy base adhesive on back support frame of 40x20x3.2 Stainless Steel supported on a square M.S hollow steel section post 40x40x3.2mm conforming to IS code firmly hanged from ceiling/beam by fixing with expandable fastners complete in all respects, as per specification & as desired by Engineer-in-Charge (Confirming to Harmonised guidelines & standards for Universal accessiblity in India-2021 issued by Ministry of Housing and Urban Affairs Government of India) |
| 58 | Providing & fixing of Single Side Signage with provision of Multilingual text integral with minimum 3.8mm thick blue/white or combine Acrylic base plate with upper case san serif words made of white acrylic non glare cut out letter of height not less than 20mm, raised above base plate by not less than 0.8mm and the equivalent workd/s written in Multilanguage i.e Regional, devnagri, English language as required with same specifications with Grade 1 Braille to be integral with the sign face and should be raised not less than 0.5mm above Acrylic base Plate complete in all respects, as per specification & as desired by Engineer-in-Charge (Confirming to Harmonised guidelines & standards for Universal accessiblity in India-2021 issued by Ministry of Housing and Urban Affairs Government of India) |
| 59 | \\"Providing & fixing of 50 mm wide antiskid tape made of slip resistant material colour contrast, edge strip/tape\\" 25mm to 50mm width self adhesive to be fixed on front edge of Stair treads to help people with visual disabliity and elderly even in dim light conditions & reduce the risk of slipping Make 3M or equivalent brand complete in all respects, as per specification & as desired by Engineer-in-Charge (Confirming to Harmonised guidelines & standards for Universal accessiblity in India-2021 issued by Ministry of Housing and Urban Affairs Government of India) |
| 60 | \\"Providing & fixing of 50mm wide high intensitiy reflective, conspicuity tape colour contrast, self\\" adhesive to be fixed on tread of stair case to help people with visual disabliity and elderly even in dim light conditions & reduce the risk of slipping Make 3M or equivalent brand complete in all respects, as per specification & as desired by Engineer-in-Charge (Confirming to Harmonised guidelines & standards for Universal accessiblity in India-2021 issued by Ministry of Housing and Urban Affairs Government of India) |
| 61 | \\"Providing & fixing of Braille labels made of Stainless Steel (Grade-304) Size 170mm x 30mm x 4mm having\\" Braille Dots raised 0.5mm above base plate complete in all respects, as per specification & as desired by Engineer-in-Charge (Confirming to Harmonised guidelines & standards for Universal accessiblity in India-2021 issued by Ministry of Housing and Urban Affairs Government of ndia) |
| 62 | \\"Providing & fixing of Single sided Tactile Map consisting of visual information and acoustic\\" information including Emergency Evacuation Layout with Provision of Multilingual text integral with minimum3.8mm thick blue/white or Combine Acrylic base plate with upper case san serif workds made of white acrylic non glare cut our letters of height not less than 0.8mm and he equivalent work/s writtenin Multilanguage i.e Regional, devnagri, English language as required with same specification with Grade 1 Braille to be integral with the sign face and should be raised not less than 0.5mm above Acrylic base Plate complete in all respects, as per specification & as desired by Engineer-in-Charge (Confirming to Harmonised guidelines & standards for Universal accessiblity in India-2021 issued by Ministry of Housing and Urban Affairs Government of India) |
| 63 | Providing and fixing of two stages of size (48 sqm each) at the existing pavilion . Construction of 2 Nos Stages one for VIP and other for Federation |
| 64 | Structural steel work in compound girders or Stanchions built up from two or more R.S. joists or channel section or plates & angles etc. including cutting and fixing all lattice bars, stiffeners, gusset plates, bolts, nuts, rivets, welding rod, etc. complete with flange plates, heads, sole plates, angle connections, etc. with hoisting and erecting in position |
| 65 | Applying priming coat with metal primer on new steel or iron work including preparation of surface. |
| 66 | Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade. |
| 67 | Providing and fixing commercial plywood 25mm thick |
| 68 | Constructin of new fencing, and Increase 2 m heigh of existing fencing by providing providing fishnet etc. |
| 69 | Dismentling/removing of damaged Existing Chain Link fencing fixed on 80mm dia GI Pipe duly by Removing welding tasks, MS Strip and Rolling it in roll to be used else where & placing in position complete as desired by Engineer-in-Charge |
| 70 | Earth work in excavation in foundations, trenches etc. in all kinds of soil where pick jumper work is not involved and not exceeding 2.0 metres depth including dressing of bottom and sides of renches, stacking the excavated soil clear from the edge of excavation and subsequent filling around masonry in 15 cm. layers with compaction including disposal of all surplus soil as directed within a lead of 30 metres. |
| 71 | Cement Concrete 1:4:8 with stone ballast or shingle.using concrete mixing volumetric type |
| 72 | Shuttering for faces of concrete foundations and foundation beam & plinth beam (vertical or battering) |
| 73 | Providing & Fixing 80mm dia GI Pipe for extension of existing fencing frame with same height and welding each together complete in all respects and as desired by Engineer-in-Charge |
| 74 | Providing and fixing GI Chainlink fencing (Jali) 10 gauge mesh size 2\\" x 2\\" fixed with GI Pipe frame with MS flat welding to pipe for proper placing and anchoring With new material complete in all respects and as desired by Engineer-in-Charge |
| 75 | Providing and fixing high quality Fish Net made of Nylon wire thickness 2mm mess size 50mm, highly UV-Stabilized for outdoor use, nylon is favored for its strength and impact to with stand high velocity puck impacted, protecting spectators scoreboards and surrounding structures to be tied with nylon string to the existing GI Pipe frame complete in all respects and as desired by Engineer-in-Charge |
| 76 | Structural steel work in compound girders or Stanchions built up from two or more R.S. joists or channel section or plates & angles etc. including cutting and fixing all lattice bars, stiffeners, gusset plates, bolts, nuts, rivets, welding rod, etc. complete with flange plates, heads, sole plates, angle connections, etc. with hoisting and erecting in position |
| 77 | Painting two or more coats excluding priming coat with synthetic enamel paint in all shades on wood work, metallic or plastered, concrete surface to give an even shade. |
| 78 | Building Eletrical E.I Works |
| 79 | REPLACEMENT OF WIRES, COVER FRAMES, MODULAR SWITCHES, CONCEALED METAL BOXES AND OTHER ACCESSORIES IN THE EXISTING RECESSED CONDUIT PIPE WIRING SYSTEM (WITH MODULAR TYPE ACCESSORIES) Derived from 34.01:conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in existing heavy gauge welded conduit pipe 20 mm/25 mm dia (1.6mm thick) ISI Marked, recessed in wall etc., complete with powder coated/anodized concealed metal boxes (1.6mm thick with Brass lugs) required for suitable number of modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10Amp. Switches, 16/20Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (For Fan Box and Call Bell), PVC Bush, bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm, 1100volts grade (For 6Amp. wall socket & plug control point) and other petty material etc. including the cost of above material, cutting and filling up of chases (with finishing the surface):- (Derived From CSR 34.01) Wiring fan point (without fan box ) |
| 80 | REPLACEMENT OF WIRES, COVER FRAMES, MODULAR SWITCHES, CONCEALED METAL BOXES AND OTHER ACCESSORIES IN THE EXISTING RECESSED CONDUIT PIPE WIRING SYSTEM (WITH MODULAR TYPE ACCESSORIES) Derived from 34.01:conductor single core FR cable (ISI marked) overall 1.5sq. mm, 1100volts grade to be laid in existing heavy gauge welded conduit pipe 20 mm/25 mm dia (1.6mm thick) ISI Marked, recessed in wall etc., complete with powder coated/anodized concealed metal boxes (1.6mm thick with Brass lugs) required for suitable number of modules (Modular accessories) for having Step type electronic fan regulators (two module) 100watts, bell push, 6Amp. 2/3 universal socket (shuttered), 16/20Amp. combined/ universal Socket (shuttered), 6/10Amp. Switches, 16/20Amp. switches with indicator etc. and covered with Frame Plate etc., PVC connector (For Fan Box and Call Bell), PVC Bush, bonding to earth with PVC insulated copper conductor single core FR cable (ISI marked) 1sq. mm, 1100volts grade (For 6Amp. wall socket & plug control point) and other petty material etc. including the cost of above material, cutting and filling up of chases (with finishing the surface):- (Derived From CSR 34.01) Wiring light point |
| 81 | RECESSED PVC CONDUIT PIPE WIRING SYSTEM WITH MODULAR SWITCHES: Wiring fan point (without fan box ) |
| 82 | RECESSED PVC CONDUIT PIPE WIRING SYSTEM WITH MODULAR SWITCHES: Wiring light point |
| 83 | RECESSED PVC CONDUIT PIPE WIRING SYSTEM WITH MODULAR SWITCHES: Wiring call-bell point |
| 84 | RECESSED PVC CONDUIT PIPE WIRING SYSTEM WITH MODULAR SWITCHES: Wiring 6Amp. Plug control comprising wall socket point |
| 85 | RECESSED PVC CONDUIT PIPE WIRING SYSTEM WITH MODULAR SWITCHES: Wiring 6 Amp. wall socket point |
| 86 | RECESSED PVC CONDUIT PIPE WIRING SYSTEM WITH MODULAR SWITCHES: Wiring 16/20 amp. power plug control point |
| 87 | RECESSED AIR CONDITIONER SUPPLY TERMINAL POINT (USED FOR HGW, PVC CONDUIT & HDPE PIPE WIRING SYSTEM WITH MODULAR ACCESSORIES): Wiring air conditioner supply terminal point recessed in wall etc., complete with powder coated/anodized concealed metal boxes required for suitable number of modules (Modular accessories) for having 25Amp. combined/ universal Socket (shuttered) and modular motor starter 25Amp. (2Module), covered with Frame Plate and other petty material etc. including the cost of above material, cutting and filling up of chases (with finishing the surface):-Wiring AC supply terminal point having 1Each 25Amp. universal Socket (shuttered) erected at AC height and 1Each Motor starter 25Amp. erected at switchboard height. |
| 88 | RECESSED COMPUTER SUPPLY TERMINAL POINTS (USED FOR HGW, PVC CONDUIT & HDPE PIPE WIRING SYSTEM WITH MODULAR ACCESSORIES) Wiring Computer terminal point having 3 Each 6Amp. 2/3 universal socket (shuttered), 1Each 16 Amp. switch with indicator and 1Each blanking plate (Modular accessories). |
| 89 | RECESSED TV, TELEPHONE & NETWORKING SOCKETS OUTLET POINTS (USED FOR HGW, PVC CONDUIT & HDPE PIPE WIRING SYSTEM WITH MODULAR ACCESSORIES): Wiring Telephone socket point RJ11 (one module) |
| 90 | RECESSED TV, TELEPHONE & NETWORKING SOCKETS OUTLET POINTS (USED FOR HGW, PVC CONDUIT & HDPE PIPE WIRING SYSTEM WITH MODULAR ACCESSORIES): Wiring Networking socket point RJ45 (one module) |
| 91 | PVC INSULATED SINGLE CORE FR COPPER CONDUCTOR CABLE: Overall size 1.5sq.mm (Un-sheathed) |
| 92 | PVC INSULATED SINGLE CORE FR COPPER CONDUCTOR CABLE: Overall size 2.5sq.mm (Un-sheathed) |
| 93 | PVC INSULATED SINGLE CORE FR COPPER CONDUCTOR CABLE:Overall size 4sq.mm (Un-sheathed) |
| 94 | PVC INSULATED SINGLE CORE FR COPPER CONDUCTOR CABLE: Overall size 6sq.mm (Un-sheathed) |
| 95 | PVC INSULATED SINGLE CORE FR COPPER CONDUCTOR CABLE: Overall size 10sq.mm (Un-sheathed) |
| 96 | PVC, HDPE PIPES & PVC FLEXIBLE PIPES:Heavy Gauge PVC Conduit Pipe 25mm dia. (Flushed) |
| 97 | PVC, HDPE PIPES & PVC FLEXIBLE PIPES:Heavy Gauge PVC Conduit Pipe 40mm dia. (Flushed) |
| 98 | PVC, HDPE PIPES & PVC FLEXIBLE PIPES:PVC flexible pipe 25mm dia. |
| 99 | MINIATURE CIRCUIT BREAKERS: MCB Single Pole 6-32amp. (10kA, Curve-C) |
| 100 | MINIATURE CIRCUIT BREAKERS: MCB Four Pole 50, 63amp. (10kA, Curve-C) |
| 101 | SHEET METAL DOUBLE DOOR DISTRIBUTION BOARD FOR MCB/ RCBO/ RCCB's: TP&N Horizontal Double Door Distribution Board 4 way each |
| 102 | SHEET METAL DOUBLE DOOR DISTRIBUTION BOARD FOR MCB/ RCBO/ RCCB's:TP&N Horizontal Double Door Distribution Board 12 way each |
| 103 | SHEET METAL DOUBLE DOOR DISTRIBUTION BOARD FOR MCB/ RCBO/ RCCB's:COPPER EARTHING STRIP (As Additional Length): Fixing additional Length of earthing with Copper Tape (On Surface/Flushed) with petty Additional Length 25mm x 3mm thick Copper Tape |
| 104 | Cable Tray:- Supply and erection of MS perforated cable tray (MS Sheet thickness 2mm) with DA gray paint on the existing surface with the help of MS angle iron supportCable Tray Size 150mm x 50mm x 50mm (2mm thick) |
| 105 | Supply and Erection of 3 Star Rating Ceiling fan Suitable size 48” (1200mm) Full Aluminium Body, 3 Each of Blades, white in colour. The mounting type is down rod mount. The product should possess a minimum air delevery of 218 CMM. The rated speed of the product must be minimum of 350 revolutions per minute and 5 Each of speed. The approximate weight of the product should be 4kg and 180gms (without packing) or higher. The product should have a manufacturer's guarantee/ warranty of minimum 2 years. The product should be complete in all respects with fan motor, bladeset, down rod, conopy set, shackle kit, twisted wire etc., including erection & testing of ceiling fans having connection with PVC insulated PVC sheathed tow single core copper conductor (FR) cable 0.75 SQ MM. Complete in all respects as desired by the Engineer in charge of work at site. |
| 106 | Supply and Erection of Heavy Duty Exhaust Fan Suitable size 12” (300mm) including Louver shutter, connection & testing complete in all respects as desired by the Engineer in charge of work at site. Exhaust Fan, Blade Sweep : 300 mm (12”), Type of motor : Permanent capacitor induction motor, C75 Rated Voltage : 230 volts, 50 Hz, AC. single Phase, Test voltage : 230 volts, 50 Hz, .AC. I Phase, Frequency : 50 Hz., Capacitor rating : 1.0 F, 400V, 50 Hz, AC., Rated watts at full (load) speed & at 230V. : 27 watts., Current in amps at full speed & at 230 V. : 0.12 Amps., Power factor : 0.9 min., Rated full speed & at 230 V : 1310 rpm., Rated air delivery at 230 V : 800 M3/hr, Rated Service value : 30 m3/hr/watt, Each of blades leaves : Five, Type of blade leaf : Plastic (PP), No of running positions : One position, Class of Insulation : Class “E”, Type of bearings : Oil impregnated self aligned bush bearings. |
| 107 | Supply and Erection of Fresh Air Exhaust Fan Suitable size 10” (250mm) including Louver shutter, connection & testing complete in all respects as desired by the Engineer in charge of work at site. Fresh Air Exhaust Fan, Blade Sweep : 250 mm (10”), Type of motor : Normal Speed, Voltage : 230 volts, 50 Hz, AC. single Phase, Test voltage : 230 volts, 50 Hz, .AC. I Phase, Frequency : 50 Hz., Capacitor rating : 1.0 F, 400V, 50 Hz, AC., Rated watts at full (load) speed & at 230V. : 40 -45 watts., Current in amps at full speed & at 230 V. : 0.12 Amps., Power factor : 0.9 min., Rated Speed : 1250 revolution per minute, Each of blades leaves : Three, Blade design : Aerodynamically designed & Blanced Blade, Weight of fan : 2.057 kg., Noise level : (40 - 45) dB, Air Displacement In M3/Hour : 780, No of running positions : One position, Class of Insulation : Class “E”, Type of bearings : Oil impregnated self aligned bush bearings. |
| 108 | Supply and Erection of 27/28 Watt Recessed/Surface mounted LED edge lit slim downlight with a durable PDC aluminum body and frosted diffuser IP 65 , it ensures uniform illumination and asleek, modern aesthetic for various applications.. Efficacy:130 lm/W. Complete in all respects as approved and desired by the Engineer in-charge at site. Besides this the Lighting Fixture manufacturer should have inhouse NABL accredited LAB. |
| 109 | Supply and erection of 24 watt recessed/ Surface mount LED Downlighter with functional range of Aesthetically designed low- depth downlighter with flushed diffuser. A Deep recessed downlighter for comfort on eye suitable for versatile applications such as offices, retail etc. complete along with erection of the same with connections testing etc. complete in all respects as approved and desired by the Engineer in charge at site. The certification and Specifications of the LED Fitting's should be as approved by O/o Advisor (Technical), Govt of Punjab vide Letter EachAT/2021/GL/1410-1422 Dated 06/05/2021.Beside this the lighting manufacturer should have inhouse NABL accreted Lab. |
| 110 | Supply and Erection of 40 Watt Polycarbonate Housing LED Batten fitting. (including LED driver) with High quality extruded aluminium with efficacy of LED fixture minimum 100 lumens per watt and operating voltage between 140 to 270 volt, input AC frequency 50 Hz ± 3 % complete along with erection of the same with connections, testing etc. complete in all respects as approved and desired by the Engineer-in-charge at site.The certification and Specifications of the LED Fitting's should be as approved by O/o Advisor (Technical), Govt of Punjab vide Letter EachAT/2021/GL/1410-1422 Dated 06/05/2021. Besides this the Lighting Fixture manufacturer should have inhouse auredited LAB. |
| 111 | Supply and Erection of 36/40 Watt (1X4) LED Recessed Mounted Light suitable for direct ceiling mounting, with its super bright LED, is a delight in modern office environment with a soft soothing light. complete along with erection of the same with connections, testing etc. complete in all respects as approved and desired by the Engineer-in-charge at site.The certification and Specifications of the LED Fitting's should be as approved by O/o Advisor (Technical), Govt of Punjab vide Letter EachAT/2021/GL/1410-1422 Dated 06/05/2021. Besides this the Lighting Fixture manufacturer should have inhouse auredited LAB. |
| 112 | Less cost of old Dismantaled material Rs. |
| 113 | Add 1% Culture Cess Please Enable Macros to View BoQ information |
