|
| 1 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m soft /loose soil in depth and getting out complete all as specified and directed. |
| 2 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and exc 1.5 m but n. exc. 3.00 m in depth and getting out soft/loose soil complete all as specified and directed. |
| 3 | Demolition of Concrete of any description an in any position not otherwise specifically provided for complete all as specified and directed. |
| 4 | Returning, filling, in soil including spreading, levelling, watering and well ramming in layers n.exc. 25cm thick complete all as specified and as directed. |
| 5 | Removing excavated material (soils) n. exe 50 m and depositing where directed at a level not exc. 1.5 m above the starting point complete all as specified and as directed. |
| 6 | M&L for cement concrete Type D2,1:4:8 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and as directed. |
| 7 | M&L for Reinfoced Cement Concrete (design Mix) M-30 (using 20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc. basement slabs, under-reamed piles and mass concrete etc. complete all as specified and as directed. |
| 8 | M&L for Reinforced Cement Concrete (design mix) M-30 (using 20mm graded stone aggregate) as in Columns, pillars, piers, podts and struts etc complete all as specified and as directed. |
| 9 | Use & waste of form work to sides of concrete foundation, footing, bases of columns, raft and raft beams, sides and soffits of foundation and plinth beams and similar work vertical or to batter, flat, rough finish surface of concrete complete all as specified and directed. |
| 10 | Use & waste of formwork torough finished surfaces of concrete, squar, rectangular or polygonal, sides of pillars, posts, struts, piers, columns and stanchion, etc complete all as as specified and directed. |
| 11 | M&L for mild steel CRS bars 10 mm dia and over cut to length, bent to shape as required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire(annealed) not less than 0.9mm dia or securing with clips, TMT bar etc complete all as specified and directed. |
| 12 | M&L mild steel CRS bars 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders cut to length, bent to shape required, and binding with MS wire not less than 0.9mm dia complete all as specified and directed. |
| 13 | M&L for precast cement concrete block masonary with solid blocks type C1 1:3:6 (20mm graded stone aggregate) exc 10cm in width and setting in cement mortar 1:6 complete all as specified and directed . |
| 14 | M&L for 15mm thick rendering in cement mortar 1:4 on fair faces of brick or concrete/PCC solid block masonary finished even and smooth without using extra cement complete all as specified and directed. |
| 15 | Material & Labour for applying Two coats of 100% Premium acrylic Emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives@ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces complete all as specified and directed. |
| 16 | M&L for Granite(of any type) work (table rubbed and polished) 20 mm thick in steps, jams, pillars, windows cills, cooking platforms and the like incement mortar (1:4) in including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite etc complete all as specified and directed. |
| 17 | Material & Labour for providing and fixing stainless steel (Grade 304) railing/ sliding gate/ folding gates made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts, bearing, wheel, SS Pin, SS handle and hinges complete, including fixing the railing/gate with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified. |
| 18 | S&F for 75mm dia stainless steel Heavy duty revolving wheel 360 degree suitable for turning, sliding gate, revolving gate, folding gate double bearing roller complete all as specified. |
| 19 | S&F in barbed razor type concertina coil hot galvanized spring tensile wire fixed on 'Y' shape angle iron post and barbed wire over compound wall/ gate, coil of 3 to 4 RM per coil of 300 mm dia, minimum weight of coil shall be 6 kg/coil complete all as specified and directed. |
| 20 | S&F for Galvanised 2 strand steel barbed wire 2.24mm dia barbed with 2 mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts including securing or tying at crossing with and provision of galvanised mild steel wire, staples or steel pins etc as directed. Note: Each line wire to be measured. Please Enable Macros to View BoQ information |
