|
| 1 | Dismantling of Bricks (laid flat or on edge) or brick tiles in floors, channels, kerbs, aprons etc laid dry or laid dry and pointed complete all as specified and directed by Engineer-in-charge. |
| 2 | Material and labour for excavating over areas , in soft loose soil n exc 1.5 m deep and getting out outside of MD land including any royalty and removing the same from any distance to work site and filling the soil on both side of road berms including watering rolling and consolidating complete all as specified and as directed by Engineer-in-charge. |
| 3 | Material and labour for providing,laying and compacting 150 mm thick (compacted thickness) Granular Sub Base Course (GSB) grading as per Grade I as specified Table 400-1 of MaRTH specifications for Road and Bridge works, 2013, in a single layer over compacted subgrade with natural sand, crushed gravel, crushed stone, crushed slag or combination thereof as per the grading required The materials are mechanically mixed, spread and leveling on the subgrade manually, and rolling with vibratory roller of capacity 80-100 KN static weight for achieving required compaction density of atleast 98% of the Maximum Dry Density. Consolidating to required gradient and camber complete all as specified and directed with finished surface tolerances as per Table 900-1 of MaRTH specifications for Road and Bridge works 2013 complete all as specified and as directed by Engineer-in-charge. Note:- In case of width of road widening is lesser, contractor has to arrange roller of lesser width for compaction. |
| 4 | Material and labour for providing, laying and compacting 150 mm thick (compacted thickness ) WMM laid in two layers of 75 mm each thick (compacted thickness) Wet Mix Macadam (WMM) grading as per table 400-13 of MaRTH specifications for Road and Bridge works 2013 manufactured in WMM plant material comprising of clean, crushed, graded aggregate and granular material premixed with water to a dense mass, spreading manually and rolling with vibratory roller of capacity 80-1OOKN static weight and consolidating to required gradient and camber complete all as specified and directed by Engineer-in-charge Notes:-(i) The finished surface tolerances shall be as per Table 900-1 of MaRTH specifications for Road and Bridge works 2013. (II) In case of width of road widening is lesser, contractor has to arrange roller of lesser width for compaction. |
| 5 | Material and labour for preparing of unsurfaced wet mix macadam by brushing with wire brushed for removing caked mud etc sweeping with brooms and finally fanning to cleaned surface with gunny bags to remove all loose dirt etc from surface and applying evenly a premix /tack coat with bituminous primer (using paving bitumen VG-10) @10.00 Kg per ten Sqm complete all as specified and as directed by Engineer-in-charge. |
| 6 | Material and labour for providing and laying Premix Bituminous macadam of (consolidated thickness 75 mm or less) using paving bitumen binder of grade VG-30 and binder content 4% by weight of total mix, Mixing of aggregates and VG-30 bitumen in electronic operated 100-120 TPH batch type hot mix plant, transporting the hot mix from HMP to work site by tippers and laying with hydrostatic paver finisher (Paver shall not be compulsory in case of patch work using B.M.) and as per approved mix, rolled & compacted to required camber and gradient with 8 to 12 tonne smooth wheeled, vibratory and tandem roller, complete all as per Clause 504 MoRTH (5th Rev) specification complete all as specified and as directed by Engr-in-Charge. Notes : 1.The contractor shall quote the rate against Item considering 4% VG-30 bitumen content. Job Mix Formula as per CI. No. 505.3.3 of MORTH (5th Rev) for BM shall be worked out from Thapar Insti. of Engg & Tech Patiala/ PEC Chandigarh/ Command Test Lab / Maharaja Ranjit Singh Tech University Bathinda for obtaining optimum binder content (OBC) by the Contractor without any financial effect to the Dept and same be submitted to Garrison Engineer for approval. Any variation in binder content on minus side shall be adjusted @ Rs 50/kg of binder and no adjustment shall be made on plus side.2. The BM shall be covered with top layer/wearing course within in a maximum of 48 hours. If ther is to be any delay, by the contractor the course shall be covered by seal coat to the requirement of Clause 512 of MORTH (5th Rev) before opening to the traffic. The seal coat in such cases shall be considered incidental to the work and shall not be paid for separately. |
| 7 | M&L for preparing of black top surface by brushing with wire brushed for removing caked mud etc sweeping with brooms and finally fanning to cleaned surface with gunny bags to remove all loose dirt etc from surface, Applying evenly a premix /tack coat with bituminous primer (using paving bitumen VG-10 )@ 5.0 Kg per ten Sqm complete all as specified and as directed by Engineer-in-charge. |
| 8 | Material and labour for providing and laying Premix Bituminous semi dense asphaltic concrete 30mm consolidated thickness with 5.5% binder (paving bitumen of grade VG-30) content by weight of total mix and mixing the crushed aggregates of grading 2 with VG-30 bitumen in electronic operated 100-120 TPH batch type hot mix plant, transporting the hot mix from HMP to work site by tippers and laying with hyrdostatic paver finisher and as per approved mix and rolled & compacted to required camber and gradient with 8 to 12 tonne smooth wheeled, vibratory and tandem roller, complete all as per Clause 507 MORTH (5th Rev) specification and as specified and as directed by Engineer-in-Charge. |
| 9 | Notes:- (i). The contractor shall quotes the rate against Item considering 5.5% VG-30 bitumen content. Job Mix Formula as per CIause. No. 505.3.3 of MORTH (5th Rev) for BC shall be worked out from Thapar Insti. of Engg & Tech Patiala/ PEC Chandigarh/ Command Test Lab / Maharaja Ranjit Singh Tech University, Bathinda for obtaining Optimum Binder Content (OBC) by the Contractor without any financial effect to the Dept and same be submitted to the Garrison Engineer for approval. Any variation in binder content on minus side shall be adjusted @ Rs 50/kg of binder and no adjustment shall be made on plus side.(ii). Cost of filler i.e. cement (Ordinary portland cement/OPC) is deemed to be included in quoted unit rate.(iii). After spreading of mix as per clause 507.4.7 entire surface during the operation shall be rolled with road roller 8-10 tonne (smooth wheeled) followed with vibratory road roller of 8-10 tonne static weight, followed by finished rolling with 6 to 8 tonne smooth wheel tendom roller as per Clause Nos. 507.4.8 and cost of the same is deemed to be included in quoted unit rate. |
| 10 | (iv) The vintage of the T&P (Hot mix plant/road roller i.e. vibratory roller, static roller, hydraulic roller/paver) should not be more than 10 years except the tippers and shall be approved by GE before date of commencement of the work.(v) The certificate wrt the capacity of the hot mix plant (HMP) shall be 100-120 TPH and the plant shall be electronic operated, batch type and location be intimated and the same shall be approved by GE before date of commencement of the work.(vi) The distance of the HMP shall not be more than 100 KM from the Mil Stn Patiala, Detail of plant to be submitted to GE for approval before date of commencement of the work.(vii) The calibration certificate for HMP shall be submitted by the contractor for approval of GE before date of commencement of the work which should not be more than 6 months old.(viii) The minimum 2 Road roller each (vibrating and static road roller) are required at site before commencement of the work on the ground and the same shall be approved by GE before date of commencement of the work.(ix) Aggregates retrieved from dismantling of existing pavement shall not be used in top carpetting layer. |
| 11 | Supply and fixing Road cat eyes of size 100mm x 100mm x 20 mm meeting with ASTM and MORTH STANDARD WITH YELLOW reflectors, yellow body colour and two saides lens all as specified and directed. The stud shall be fixed to the road surface using adhesive and zinc plated nails conforming to IS as per manufacturer recommendations and as approved by GE complete all as specified and as directed by Engineer-in-charge. |
| 12 | Supply and fixing in repair solar cat eye aluminum alloy shall (light sensor 100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono rystafie solar panel 2.4V/0.3 watt on NI-ed rechargeable battery (1.2V/1600MA) consisting of super bright 3 LED's of colur red/yellow on one side with 10,000 to 18,000 mcd . The stud shall be fixed to the road surface using adhesive and zinc plated nails conforming to IS as per manufacturer recommendations complete as approved by GE complete all as specified and directed by Engineer-in-charge. |
| 13 | Material and labour for Marking strips, straight line, zebra crossing and stop line 100 mm wide and not less than 2mm thick with hot applied thermoplastic road marking paint (white or yellow) mixed with glass beads, using automatic mechanical road painting machine complete all as specified and as directed by Engineer-in-charge. |
| 14 | Material and labour for 75 mm thick cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub-floor, sub-base, flooring, Hardstanding and paving etccomplete all as specified and as directed by Engineer-in-charge. |
| 15 | Material and labour fot providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed by Engineer-in-charge. |
| 16 | Material and labour for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and as directed by Engineer-in-charge. |
| 17 | Material and labour for laying in trenches reinforced concrete pipes 300 mm bore, class NP3, laid and jointed complete with collars including cemenr concrete1:3:6 type C-2, bed to drain pipe and packing under and haunching against the side of pipes after they are laid and tested complete all as specified and directed by Engineer-in-charge |
| 18 | Demolition of Brickwork of stone/boulder masonry, build in cement mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articles complete all as specified and directed by Engineer-in-charge |
| 19 | Material and labour for Brick work using Sub Class \\"B\\" brick straight or curved on plan not exceeding 6 Mtr means radius built in CM 1:4 complete all as specified and directed by Engineer-in-charge |
| 20 | Material and labour for Manufacturing, supplying and fixing retro reflective Mandatory/ Regulatory sign boards of 450/300 mm diameter with support length of 3750 mm and made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM- -4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete all as specified and directed by Engineer-in-charge |
| 21 | Supply and fixing in repair convex mirror of dia 80 cm with complete fixing arrangement as per manufacturer instructions includingembedding of mild steel post in PCC 1:2:4 (150x150x300mm) type B1 complete all as specified and directed by Engineer-in-charge |
| 22 | Supply and fixing metal tubular dealineator made out of ABS round body fitted with 2 Nos 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in PCC 1:2:4 (150x150x300mm) type B1complete all as specified and directed by Engineer-in-charge Please Enable Macros to View BoQ information |
