|
| 1 | Safe carriage of following materials from Store centre or any other place to the respective site of work through the Kachha/Pacca road including loading, unloading at the respective ends and erection of same including the work of dragging as per site requirement, jumphering, Cost of labour, T&P carrier etc. required for proper completion of work as per RESPO Norms is included in the work. |
| 2 | 11 Mtr ST Pole (for Double/Single/Section) |
| 3 | Earthing of pole |
| 4 | 11 kv RMU 3 Way (Motorized) |
| 5 | 11 kv XLPE Cable 3x185Sqmm |
| 6 | 11 kv XLPE Cable 3x120Sqmm |
| 7 | 11 kv I/C Jointing kit 3x185Sqmm |
| 8 | 11 kv O/G Jointing kit 3x185Sqmm |
| 9 | 11 kv O/G Jointing kit 3x120Sqmm |
| 10 | 11Kv Pin Insulator with Pin & Nut |
| 11 | 11KV V-type Cross Arm |
| 12 | Disc Insulator with fitting T&C type 45KN |
| 13 | Stay Set Complete |
| 14 | Supply, fixing and erection of following materials as per site requirement as per RESPO Norms:- |
| 15 | T Off channel 125x65x1300mm |
| 16 | MS Top channel 100x50x2240 mm |
| 17 | MS ANGLE IRON 65x65x6 mm, 2700 mm long bracing with 4 clamp |
| 18 | MS Dropper Channel for support of GI pipe and 11KV XLPE Cable 100x50x2240mm. |
| 19 | Clamp for Tee-Off channel |
| 20 | Clamp for pole |
| 21 | Clamp for Cross Arm holding with Nut & Bolt |
| 22 | PG Clamp for Dog to Dog |
| 23 | wooden bushes with Nut & Bolt |
| 24 | MS CHANNEL (Dropper) FOR SUPPORT OF GI PIPE AND 11 KV XLPE CABLE 100X50X2240 MM |
| 25 | G.I. Pipe 6\\" dia |
| 26 | HDPE PIPE 140/160 MM (LAYING OF HDPE PIPE WITH HT XLPE CABLE BY DIGGING/DRILLING PROPERLY WITH COMPLETE JOB) |
| 27 | CABLE ROUTE MARKER |
| 28 | Stone Pad 300x300x75mm. |
| 29 | F-Bracket for fitting Top Insulator with nut& bolt |
| 30 | Al. Winding Wire (6SWG) |
| 31 | Danger Board with Nut & Bolt |
| 32 | Barbed Wire (GI) |
| 33 | Number Plate with nut & bolt |
| 34 | ALLUMINIUM PAINT |
| 35 | RED OXIDE PAINT |
| 36 | GI Wire 6SWG for supporting of Cable |
| 37 | Concreting of the Stay |
| 38 | Concreting of the support by a mixture of 1:4:8 (by volume). The size of the pole plinth is kept as 450x450 mm and height 300 mm above ground level as per drawing. The top 100 mm is kept tapered so that no rainwater gets accumulated on the top. The underground portion of the concreting shall be 450 mm x 450 mm x depth of plantation of support. |
| 39 | Errection, Grouting, Plinth of 11 KV RMU |
| 40 | Neutral & Body earthing at 11KV RMU by drilling/boring a hole of size 200 mm dia and 3000mm long in depth and then inserting the Gel earthing electrodes of size 50mm dia and 3000 mm long inside the pit then mix the back fill compound nicely with the soil and re-filling the empty space around the earthing electrode including making of chamber at the top of the earthing as per direction of supervising engineer. It includes the cost of all material labour, T&P, carrier etc. required for proper completion of work. The aforesaid work shall be carried out as per RESSPO norms. Max neutral to earth voltage should be less than 3 volts and earth resistance should be less than 1 ohm. |
| 41 | Providing and fixing of welded wire mesh fencing around 11KV RMU with M.S. Angle of size 35X35X6 mm. length and 1.20 Meters height, such panels shall be supported on M.S. Angle from of size 40X40X6 mm. having 04 Nos. corner supports of height 1.65 Meters including extended legs for grouting which will be used as a door for entry of the personnel or removal/shifting of transformer with welded hinges, sliding belt etc. for locking the arrangement as per drawing and specifications the fencing will be painted one coat of red oxide primer and then two coats of bus green synthetic enamel paint. The rates should be inclusive of all materials required for proper completion of above work (length of each fencing approx. 11 Meters) Please Enable Macros to View BoQ information |
