|
| 1 | Total amount of Sch 'A' Part-I (Building Works) lump sum price worked out by the contractor for \\"Building Works\\" as listed in Schedule 'A' Part-I |
| 2 | Total amount of Sch 'A' Part-II (Site Clearance and Earth Work Works) lump sum price worked out by the contractor for \\"Site Clearance and Earth Work Works\\" as listed in Schedule 'A' Part-II. |
| 3 | Total amount of Sch 'A' Part-III (Internal Water Supply Works) lump sum price worked out by the contractor for \\"Internal Water Supply Works\\" as listed in Schedule 'A' Part-III. |
| 4 | Total amount of Sch 'A' Part-IV (Internal Electrification Works) lump sum price worked out by the contractor for \\"Internal Electrification Works\\" as listed in Schedule 'A' Part-IV. |
| 5 | Total amount of Sch 'A' Part-V (Sewage Disposal Works) lump sum price worked out by the contractor for \\"Sewage Disposal Works\\" as listed in Schedule 'A' Part-V. |
| 6 | Total amount of Sch 'A' Part-VI (Road, Path, Culverts Works) lump sum price worked out by the contractor for \\"Road, Path, Culverts Works\\" as listed in Schedule 'A' Part-VI. |
| 7 | Total amount of Sch 'A' Part-VII (Area Drainage Works) lump sum price worked out by the contractor for \\"Area Drainage Works\\" as listed in Schedule 'A' Part-VII. |
| 8 | Total amount of Sch 'A' Part-VIII (External Electrification Works) lump sum price worked out by the contractor for \\"External Electrification Works\\" as listed in Schedule 'A' Part-VIII. |
| 9 | Total amount of Sch 'A' Part-IX (External Water Supply Works) lump sum price worked out by the contractor for \\"External Water Supply Works\\" as listed in Schedule 'A' Part-IX. |
| 10 | Schedule 'A' Part- X (Misc Items of Works) Note : This schedule is not pre priced by MES and the pre-priced rate indicated as \\"Rs 0.00\\" under Col 5 signifies this fact only |
| 11 | INTERNAL WATER SUPPLY WORKSS&F CP Wall mounted basin spout and operating lever quarter turn consisting of exposed part and concealed part complete all as specified. Make: Cera (F1015653/F4055101) or equivalents from Hindware/Jaguar as approved |
| 12 | INTERNAL ELECTRIFICATION WORKSSupply, installation, testing and commissioning of OEM make 8-way, Double Door type structure/wall mounted indoor panel having encapsulated copper bus bar (PAN assembly) to avoid any lose connection / heat loss. The complete panel shall be modular in construction and suitable for indoor application having provision for floor mounting as well as wall mounting arrangement. Panel shall be 11 tank powder coating for better environment protection, CRCA sheet steel / 1.6 mm. The complete panel shall be manufactured by OEM only. Panel & MCCB shall be manufactured by same company.Panel should be rigid & weld free construction to reduce distortion. Removable door with easy align hinge to aid installation. Chrome plated hinges shall be provided. Door barrel lock accessory for increased security. Powder coated paint for better environment protection.Cable holder provision in cable alley. Ingress protection, IP 30 for single door and double door. Door opening to 180 deg for easy access. The panel shall also have a provision for to install changeover module for any future requirement.The panel shall have digital metering (Voltage and current) along with indication lamps.. Panel shall have provision of Cable Alleys on both the sides for ease of termination. Makes Approved – ABB, Havells, L&T, SiemensINCOMING:-(a) MCCB 320 Amps, Adjustable thermal and fixed magnetic type 4 pole, 415 Volts, 36 KA, having Ics=100%Icu - 01 NosOUT GOING:-(a) MCCB 40A,415V 4Pole,25KA, having Ics=100%Icu----03 Nos(b) MCCB 100A,415V 4Pole,25 KA,having Ics=100%Icu---- 01 Nos(c) MCCB 16 A;415V 4 Pole, 18 KA,having Ics=100%Icu---- 2Nos |
| 13 | SEWAGE DISPOSAL WORKSConstruction of Septic tank for 50 Users with excavation, foundation PCC 1:2:4, brick work in CM 1:4, RCC slab covers including RCC precast manhole cover having 6mm thick MS plate embeded all around fibre reinforced cover with angle iron frame Vent shaft and sludge chambers etc complete all directed and as shown in drawings no. STD 1320(C) dt 25 Jun 2018 (Sheet No 1/3 to 3/3). |
| 14 | Construction of Soakage Well of Size 3.0 mtr dia and 4.5 mtr deep with excavation, foundation in PCC 1:3:6 walls in honey combed brick masonry in CM 1:4 with top ring of M-25 RCC including intercepting chamber and screen chamber made of brick masonry in CM, RCC cover slab in RCC M-25, SFRC cover, interconnecting pipes of RCC/DWC, filled with brick bats complete all directed and as shown in drawing no. STD 1173 (C) dt 25 Jun 2018 (Sheet No 1R/2 to 2R/2). |
| 15 | AREA DRAINAGE WORKSSupply and Fixing 70mm thick SFRC Factory made drain covers with perforations and with MS frame of flat iron minimum 1.25mm thick complete all as specified |
| 16 | EXTERNAL ELECTRIFICATION WORKSSupply and fixing cable jointing kit 11 KV (earthed) grade cable for Outdoor Termination (heat shrinkable) type joint complete with jointing material and all accessories for 3 core XLPE armoured aluminium conductor cable of size 120 Sqmm complete all as specified and directed. |
| 17 | Supply and fixing cable jointing kit 11 KV (earthed) grade cable for indoor Termination (heat shrinkable) type joint complete with jointing material and all accessories for 3 core XLPE armoured aluminium conductor cable of size 120 Sqmm complete all as specified and directed. |
| 18 | Material and labour for earthing complete with galvanized steel plate electrode 600 mm x 600 mm x 6.0 mm thick, burried directly in ground vertically in pit of size 900 x 900cm depth not less than 4.0 meter below normal ground level with top edge of the earth plate at a depth not less than 3.4 meter below normal ground level and covered surrounded from all sides with mixture of charcoal and common salt in alternate layers (each layer of 0.23 cu. m) upto 15cm above top of plate and electrode connected to galvanized iron strip 32 x 6 mm size by means of GI bolts, nuts, check nuts and washers, earth strip protected by galvanized steel pipe 40 mm bore (light grade) connected to main switch board or any other electrical equipment all as shown in electrical plate No. 3 of SSR-2009 Part I and including necessary excavation and earth work in any type of soil, 20 mm bore medium grade GI pipe for watering, funnel with wire mesh, PCC (1:3:6), type C-1 chamber, RCC (1:2:4), type B-1, reinforced with 6 mm dia MS round bars @ 15 cm c/c both way for cover and MS frame etc., complete all as specified. NOTE: 1. The unit rate includes earth strip and protection pipe upto (maximum 7.5 meter from earth plate) earth point/test point. 2. Earth test will be carried out and resistance should be less than 3.0 Ohm. |
| 19 | M&L for earthing complete with galvanized steel plate electrode 600 mm x 600 mm x 6 mm thick, burried directly in ground vertically in pit of size 900 x 900cm depth not less than 4.0 meter below normal ground level with top edge of the earth plate at a depth not less than 3.4 meter below normal ground level and covered surrounded from all sides with mixture of charcoal and common salt in alternate layers (each layer of 0.23 cu. m) upto 15cm above top of plate and electrode connected to galvanized wire 4 mm size by means of GI bolts, nuts, check nuts and washers, earth strip protected by galvanized steel pipe 40 mm bore (light grade) connected to main switch board or any other electrical equipment all as shown in electrical plate No. 3 of SSR-2009 Part I and including necessary excavation and earth work in any type of soil, 20 mm bore medium grade GI pipe for watering, funnel with wire mesh, PCC (1:3:6), type C-1 chamber, RCC (1:2:4), type B-1, reinforced with 6 mm dia MS round bars @ 15 cm c/c both way for cover and MS frame etc., complete all as specified. NOTE:- The unit rate includes earth strip and protection pipe upto maximum 7.5 meter from earth plate, earth point/test point |
| 20 | Supply and fixing security light fittings LED 45 watt with lens luminaire IP 66 including bracket of 43 mm dia complete with all fitting clamp nut bolt accessories as directed by Engineer-in-Charge |
| 21 | Supply and fix time switches astro type (Having longitude and latitude of Indian cities in memory) 250 V single phase of c on actor rating 32 Amp TP, 6 KW, MCB rating 40 A TPN fitted inside steel enclosure complete all as specified and directed by Engr-in-Charge |
| 22 | Supply, installation, design, fabrication, testing and commissioning of reputed factory made, outdoor type LT feeder pillar box mounted working on 415V, 3-phase, 50 Hz, AC supply, including PCC platform (300mm above from ground level and 450mm depth of foundation), with double door shutters (front and rear side openable) made out of 3.15mm CRCA sheet (incoming and outgoing), with aluminium busbar (duly insulated PVC sleeves as per colour code) on suitable insulators, mechanical supports, common earth bus at bottom, earth terminals on both sides of the panel for connecting earth stations, mechanical interlocking system for individual MCCB, ammeter, voltmeter, indicating lamps LED type for RYB and including insulators for 11 KV working pressure fixed to and including MS channel with nuts, bolts, and washer etc. synthetic bounded fuse carring tube complete with line fap suitable for current carry capacity 200 Amps complete as secified and as directed. Note: Panel size and depth of panel not less than 50CM and comprising the following items are as under:- company manufacturer only and depth of panel not less than 50CM and comprising the following items are as under:-(a) Incomer: ACB 4 Pole, 415 V, with Thermal Magnetic Release (Manual Draw out type) of capacity 600 Amps(b) Outgoing feeders: (i) 4 Pole MCCB 200A, 36kA-01Nos, Including rotary handle and one additional DPX spreader 3 links set Make : Legrand/Siemens/ABB(a) Incomer: ACB 4 Pole, 415 V, with Thermal Magnetic Release (Manual Draw out type) of capacity 600 Amps(b) Outgoing feeders:(i) 4 Pole MCCB 160A, 25kA - 2 Nos, Thermal magnetic O/L and S/C protection, including rotary handle, indicator set.(ii) 4 Pole MCCB 200A, 36kA-01Nos, Including rotary handle and one additional DPX spreader 3 links set Make: Legrand/Siemens/ABB(iii) MCCB TP 63 Amp, 16kA - 3Nos including rotary handle and one additional DPX spreader 3 links set Make: Legrand/Siemens/ABB(C) Panel Fabrication and TPN copper bus bar of capacity 900 Amp, multifactional meter for incoming MCCB, indicator (RYB) and selector switches complete all as specified and directed and as directed by Engr-in-charge. |
| 23 | Supply and fixing drop out fuse unit explusion type for 11 KV working pressure fixed to and including MS channel with nuts, bolts, and washer etc. synthetic bounded fuse carning tube complete with line fap suitable for current carry capacity 200 Amps complete as specified and as directed. |
| 24 | Material and labour for post insulator, porcelain, vitreous 150 mm high and 255 mm dia ball and socket type, white, brown or green, working pressure 11000 volts, complete all as specified and as directed |
| 25 | Disconnecting 100 KVA transformer from main 11 KV main power supply by GOD switch carefully and disconnecting LT side cable Earthings and taking down carefully and shifting to location and mounting it on proper structured foundation as directed by ENGR-IN-CHARGE |
| 26 | Disconnecting existing 11 kv four pole structure from main power supply carefully and dismantling this four pole structure inc. complete cross arms, GOD, insulator, lightening arrestor etc. and deposit to MES Store Please Enable Macros to View BoQ information |
