|
| 1 | Demolition of RCC of any description and in any position not other wise specially provided for (reinforcement cut as required to facilitate demolition ) complete all as specified & directed. |
| 2 | Material and labour for reinforced cement concerete 1:2:4, type B-1 (nominal mix) using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams, columns, shelves and like complete all as specified and directed. Note:- Reinforcement shall be measured and paid for separately |
| 3 | Use and waste of Formwork to soffits of suspended slab such as roof slab, floor slab, landing and similar work; flat rough finished surfaces of concrete complete all as specified & directed. |
| 4 | Use and waste of Formwork to edges of concrete flats, treads, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide, complete all as specified and directed. |
| 5 | Material and labour for mild steel TMT Bars 6 to 8 mm and above cut to length bend to shape required including cranking bending spirally for column, hooking ends & binding with and including mild steel mild steel wire (annealed) not less that 0.90 mm dia or securing with chips complete all as specified and directed. |
| 6 | Demolition of cement concrete (unreinforced) of any description and in any position not other wise specially provided for and including floor finishes and removing the rubbish outside MoD land complete all as specified & directed. |
| 7 | Material and labour for 75mm thick PCC 1:3:6 type C-2 ( using 40mm graded aggregate) as in plinth protection laid in alternate bays, surface finished even & smooth without using extra cement including making joints complete all as specified and directed. |
| 8 | Material and labour for 25mm thick PCC (1:2:4) type B-0 ( using 12.5mm graded aggregate) as in sub base of floor surface finished even & rough to receive floor topping complete all as specified and directed. |
| 9 | M & L for 15mm thick plastering/screed bed or bedding layer in CM 1:4 on brick/concrete surfaces as in sunken floor mixed with water proofing compound as per manufacturers instruction even and smooth without using extra cement complete all as specified and directed. Note:-WPC shall be measured and paid separately |
| 10 | Applying a tack coats of industrial bitumen 85/25 grade at the at the rate of 1.2kg per sqm as in sunken floor portion including preparation of plaster on concerte surface complete all as specified and directed. |
| 11 | Supply only integral water proofing compound complete all as specified and directed |
| 12 | M & L for APP based polymeric membrane minimum weight 3 Kg/Sqm and minimum 3 mm thick, reinforced with polyester non wove fabric (wt. not less than 150 gms/Sqm ) laid by torch forced application over and including a priming coat using bituminous primer @ 0.40litre/ sqm as per manufactures instruction on concrete surface complete all as specified and directed by Engineer- in charge. |
| 13 | Supply and fixing in repairs 40 mm bore 600mm long GI spout for draining the surplus water from the sunken portion including cutting hole and making good the disturbed surface in cement mortar 1:3 or PCC 1:2:4 complete all as specified and directed. |
| 14 | M & L for PCC 1:2:4 Type B-2 (using 20mm graded stone aggregate) as in flooring incl finishing the cement concrete surface even and smooth with using extra cement , rubbish off the premises and incl demolition of PCC complete all as specified and directed . |
| 15 | Material and labour for PCC 1:4:8 Type D2 (using 40 mm graded stone aggregate), as in mass concrete in sunken floor, complete all as specified and directed. |
| 16 | Material and labour for 40mm thick PCC 1: 2: 4 type B-1, (using 20mm graded stone aggregate) as in floor & finishing the surface even & smooth using extra cement complete all as specified and directed. |
| 17 | Dismantling floor, hearth wall tiling including cement mortar bedding removing serviceable tiles to store & rubbish off the premises. Note :- The demolished material shall be disposed off outside MoD land. The contractor shall quote his rates considering the above element, no extra paid on this. |
| 18 | M&L for glazed ceramic coloured wall tiles 450x300x7mm thick on vertical surfaces such as dados set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick backing coat in CM 1:4 complete all as specified and directed by Engineer-in-Charge. |
| 19 | Material and labour for non-skid, ceramic, coloured tiles 7 to 8mm thick (Square/rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors, set and jointed in cement slurry and pointed in white or coloured cement to match with the shade of tiles laid over and including 15mm thick screed bed or bedding layer in CM 1:6 complete as specified and directed. |
| 20 | Material and labour for non-skid, ceramic, coloured tiles 7 to 8mm thick (Square/rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in skirting, set and jointed in cement slurry and pointed in white or coloured cement to match with the shade of tiles laid over and including 10mm thick backing coat on fair faces of brick work or concrete surface in CM 1:4 complete all as specified and directed. |
| 21 | M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0. 06 sqm but not exceeding 0.11 sqm, in floors etc. laid over 15mm thick screed bed in cement mortar 1:6 and jointed in neat cement slurry and pointed in white or coloured cement to match incl dismantling / demolition and rubbish off the premises etc complete all as specified and directed. |
| 22 | M&L for vitrified light shade ceramic tiles 8 to 9 mm thick polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles and laid over & including 15 mm thick screed bed in CM 1:6 complete all as directed by Engineer-in-Charge. |
| 23 | M&L for vitrified light shade ceramic tiles 8 to 9 mm thick polished, area of each tiles not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles and laid over including 10mm cement backing coat in CM 1:4 complete all as directed by Engineer-in-Charge. |
| 24 | Dismantling of stone slab and tiles of any description or thickness in floors aprons etc, laid bedded and pointed in any mortar complete all as specified and directed. |
| 25 | Material and labour for 18 to 20 mm thick granite (of any type) work (table rubbed and polished) in steps, landings, window cills cooking plate form and like in cement moryar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over and including 15mm thick screed bed or bedding layer in cm 1:6, and including rounding of edges of granite slabs 10 to 20 mm thick by grinding and rubbing and finished smooth, coloured etc complete all as specified and directed.Note: Front facia edges of granite slabs shall be rounding and finished smooth. The contractor shall quote his rates considering the above element, no extra paid on this. |
| 26 | All as per description of serial Item No. 25.00 here in before but as on vertical surfaces and laid over and including 10 mm thick rendering in CM 1:4 complete all as specified and directed. |
| 27 | M & L for machine cut Kota Stone slab as in flooring / landing/treads of stairs , 20-25 mm thick over and including 15mm thick cement screed bed in CM 1:4 , laid and jointed with grey cement slurry mixed with pigments to match the shade of the slab and including rubbing and polishing and making grooves in treads ( as required ) complete all as specified and directed. |
| 28 | M & L for machine cut Kota Stone slab as in skirting/ Risers of stairs , 20-25 mm thick laid over and including 10 mm thick rendering in CM 1:4 , laid and jointed with grey cement slurry mixed with pigments to match the shade of the slab and including rubbing and polishing complete all as specified. |
| 29 | M & L for providing 75 mm thick PCC 1:4:8 type D-2 (using 40 mm graded stone agg.) in sub base of flooring and complete all as specified and directed. |
| 30 | M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658 -2006 of 60mm thickness, M 30 grade with grey cement, pigment with 25mm thick sand filling incl dismantling old paver block and rubbish off the premises complete all as specified and directed. |
| 31 | M & L for chequered tiles of size 300 x 300 x 25 mm thick (colour and glazed approved by EIC) with grey cement and pigments laid over nad including 15 mm thick screed bed in CM 1:6 bedded and jointed in neat cement slurry, incl dismantling old unservicable tiles complete all as specified and directed. |
| 32 | Taking down cement plaster on brick or stone walls/ceiling etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified & directed. Note :- The demolished material shall be disposed off outside MoD land. The contractor shall quote his rates considering the above element, no extra paid on this. |
| 33 | Demolition of brick or stone masonary built in cement mortar incl all quions, arches, pillar etc. complete all as specified & directed. |
| 34 | Material and labour for brick work with sub class -B bricks old size, straight or curved on planexc 6m mean radius built in CM 1:6. complete all as specified & directed. |
| 35 | All as per description of serial Item no. 34.00 (here in before) but as in half brick thick wall built in CM 1:4 complete all as specified & directed. |
| 36 | Material and labour for 15mm thick rendering on other than faces of brick work or concrete surface in cm 1:6 to be finished even and smooth without using extra cement complete all as specified and directed. |
| 37 | Material and labour for 10mm thick rendering on concrete surface in cm 1:3 as in ceiling surface to be finished even and smooth without using extra cement complete all as specified and directed. |
| 38 | Material and labour for 15mm thick rendering on fair faces of brick work or concrete surface in cm 1:4 to be finished even and smooth without using extra cement complete all as specified and directed. |
| 39 | Material and labour for applying three coats of white wash on newly plastered surfaces of wall including preparation of surfacs complete all as specified and directed. |
| 40 | Perparation of newly surface plastered surface and applying two coats of oil bound distemper emulsion over one coat of primer and over two coat of cement based wall care putty complete all as specified and directed. |
| 41 | Material and labour for three coats of white wash on newly plastered surfaces of ceiling including preparation of surfaces complete all as specified and directed. |
| 42 | Perparation of newly plastered surface and applying two coats of acrylic emulsion exterior paint over coat of primer, tint as approved by Garrison Engineer in camouflage pattern to match existing surface over two coat of cement based wall care putty complete all as specified and directed. |
| 43 | Material and labour for preparation of plastered or unplastered old decorated surfaces of walls including brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots as required, and applying one coat of white lime wash complete all as specified. |
| 44 | Material and labour for preparation of old plastered or unplastered old decorated ceiling including brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots as required, and applying one coat of white lime wash complete all as specified. |
| 45 | Material and labour for preparation of old plastered or unplastered old decorated surfaces of walls including brooming down with steel wire brushing scrapping down smoke soot moulds moss and efflorescence salts and trading oil and greasy spot including washing, rubbing down and stopping the connected previously treated surfaces and applying one coat of oil bound distemper emulsion complete all as specified and directed. |
| 46 | Taking down chowkats or frames but with shutters (with out taking off shutter from the frames) not exc 1.5 sqm each complete all as specified and directed. |
| 47 | Taking down chowkats or frames but with shutters (with out taking off shutter from the frames) Exc 1.5 sqm but n. exc 4 sqm each complete all as specified and directed. |
| 48 | Taking down shutters of any description exc 1sqm but n. exc 2 sqm each complete all as specified and directed. |
| 49 | Taking down shutters exc 1 sq. M and n exc 2 sq. M each of any description including resecuring, easing ,adjusting, welding etc and refixing in same or different opening of similar nature complete all as specified and directed. |
| 50 | Supplying & fixing (MS 1.25 mm thick Pressed Steel door frames size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including filling back hollow with PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate complete all as specified and directed. |
| 51 | Supplying & fixing (MS 1.25 mm thick) Pressed Steel door frames size 125x60mm for double doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including filling back hollow with PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate complete all as specified and directed. |
| 52 | S&F Mild steel framed work as in door / cup board frames etc including necessary cutting, welding, drillings holes and fixed in position,complete all as specified and directed. |
| 53 | Supplying & fixing solid PVC door frames of sizes 50mm x 47mm made out of 5mm single side prelam PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with prelam sheet reinforced with MS Square tube complete all specified and as directed. |
| 54 | S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded prelam PVC \\"C\\" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam colour PVC sheets for top rail , lock rail and bottom rail on either side and as gap insert for top rail and bottom rail , both side prelam PVC sheet used instead of plain colour PVC sheet. Stile and rail feathered at edges paneling of prelam solid sheets 10 mm thick to be fitted in the MS framewelded, sealed to the stiles and rails with suitable PVC sheet beading , and jointed together with solvent cement complete all as specified in SSR Part -II. |
| 55 | S & F factory made Glazed & Skeleton shutters 35mm thick open rebated & prepare to received glass, gauge etc edges of framing plain chamfered or rounded in window, ventilator etc are provided with stiles and rails in 2nd class hard wood all as specified in SSR part-I, section 8 clause 8.20(b). |
| 56 | S&F 35 mm thick factory made 2nd class hardwood, Plain, framed, panelled shutters (any number of panels), in with panels of timber flat on both sides (feather edged), of 12 mm BWP commercial ply with commercial veneering on both faces; supplied and fitted to chowkhats complete all as specified and directed. |
| 57 | Dismantling boarding, any description any size , fixed in any position with screws complete all as specified and directed. |
| 58 | S&F 18 mm thick Celuka Ply of density 600kg/cum of plain colour Sheet for kitchen cabinets sides, top, bottoms and shelves inside the cabinet complete all as specified and directed.. |
| 59 | M & L for providing cupboard shutter in repair in required size at site made out of 18 mm thk PVC colour sheet and provision of shutters one side decorative pre laminated PVC sheet and all required brackets SS screws etc. The panels shall be fabricated using adhesive and screws where required. All the edges shall be covered with 2 mm thk edge bonding tape or 90 degree edge bent finish as per make and specification mentioned complete all as specified and directed by Engineer-in-charge. |
| 60 | S & F Continuous (piano) hinges, 40mm width of flaps when open brass, bright finish or electro galvanised complete all as specified and directed. |
| 61 | Supply and fixing Stainless Steel (SS 304) handles 100 mm size for Kitchen Cabinet Shutters complete all as specified and directed. |
| 62 | S&F factory made box type steel window 1.25mm thick ERW hollow P section of each frame size 60mmx25mm including grill using 10 sqmm bar double rebated both guage and glass shutter comprised gaused glazed & Skelton shutter ERW section 50mmx20mm & 1mm thick with two openable leaf consisting of two number sash bars of T-Section 20mmx3mm complete welded to frame with one vertical mullion of ERW box type T-Section of size 60mmx25mm and 1.25mm thick with following fittings welded to the frame shutter :-(i) Hold fast 150mm long mild steel flat iron 12x3 mm made to shape- 04 Nos per window. (ii) Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf.(iii) MS tower bolt 150mm long 2 No per leaf. (iv) Z section 20mmx25mm, 100mm long stopper – 01 Nos per leaf. (v) Cleat 55 mm long of solid square 15x20x.63mm square - 01 Nos per leaf (vi) MS pintal hinges 12 x 75 mm - 2 Nos each leaf (vii) 10 mm squre guard bar @ 10 cm c/c (viii) 25 x 3 mm flat iron for joint of both frame wiremesh & Glazed welded inner side and outer side of frame (ix) 0.36 mm nominal dia of stainless steel wire mesh and average width of aperture 1.40 mm fixed in glazed/gazed skelton shutter of window(x) 3mm thick sheet glass ordinary quality and with oil putty in squre n exc 0.50 sqm in each pane fixed in glazed /guage skelton shutter of window (xi) Fabrication and fixing arrangements as per specification including taking down, cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 /cement plaster 1:4 as require and make finish good to the existing surface complete all as specified and directed.(xii) Two coat of synthetic enamel paint over one shop coat of red oxide primer.Note: (i) Windows shall be provided as per the TD of Chief Engineer Chandigarh Zone, TD-219 i.e typical details of Box window (Steel) with fly proof shutter.(ii) The mode of measurement shall be only one for the set of two i.e wire mesh window and glass window at one location and nothing extra shall be measured on this account. |
| 63 | S & F mild steel box type ventilator fixed type with glazing bar with mesh & glass complete all as specified and directed all as per item ser No 62.00 (here in above) |
| 64 | Material and labour for surfaces of any description otherwise describe ver 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer, including preparation of new wooden surface complete all as specified and directed. |
| 65 | Preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.. |
| 66 | Taking down shutters of any description exc 1sqm but n. exc 2 sqm from chowkhat and re-fixing in same or different opeing after re-securing or easening and adjusting including repair complete all as specified and directed. |
| 67 | Supply and fixing butt hinges extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, 100mm, ISI marked, fixed with stainless steel screws complete all as specified and directed. |
| 68 | S&F in repairs butt hinges extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, 100mm, ISI marked, fixed with stainless steel screws complete all as specified and directed. |
| 69 | Supply and fixing 200mm long aluminium anodised barrel tower bolt, extruded section,fixed with stainless steel screws complete all as specified and directed. |
| 70 | S&F in repairs Mild steel handle for Steel window of size 150mm length fixed with nut and bolts or screw suitable for existing provisions complete all as specified and directed. |
| 71 | Supply and fixing in repairs Mild steel peg stay size 250mm length fixed to Steel window with nut and bolts or screw suitable for existing provisions complete all as specified and directed. |
| 72 | Supply and fixing 150 mm size extruded aluminium aluminium alloy handels fabricated type, anodised fixed with stainless steel screws complete all as specified and directed. |
| 73 | Supply and fixing 300mm aluminium alloy, anodised sliding door bolt with hasp staple (bolt type) fixing clips of sheet, cast or extruded setions and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed with stainless steel screws complete all as specified and directed. |
| 74 | S&F Ball magnetic catcher with 8mm dia steel ball, brass body and striking plate fixed with brass screws or with adhesive complete all as specified and directed. |
| 75 | Supply and fixing in repair 150mm long Hasp and staple stainless steel sefty type bright including bolt to hinge plate and fixed with fixed with stainless steel screws complete all as specified and directed. |
| 76 | Supply and fixing stainless steel wirecloth 0.36 mm nominal dia of wire and average width aperature 1.40mm and fixed with stainless wire staples complete all as specified and directed. |
| 77 | Supply and fixing in repair stainless steel wirecloth 0.36 mm nominal dia of wire and average width aperature 1.40mm and fixed with stainless wire staples complete all as specified and directed. |
| 78 | S&F in repair Beads, staff beads, flutes, reeds, ditto fixed with stainless wire staples complete all as specified and directed.. |
| 79 | Supply and fixing 140mm long floor door stopper of aluminium alloy body and toungue, anodised wirh hard drawn steel spring,fixed to door shutter fixed with stainless steel screws complete all as specified and directed. |
| 80 | S&F in repair 140mm long floor door stopper of aluminium alloy body and toungue, anodised wirh hard drawn steel spring,fixed to door shutter fixed with stainless steel screws complete all as specified and directed. |
| 81 | S&F 3.0mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.50 Sqm in each panes and Hacking out old broken glass (any thickness size quality or description) from wooden frames or stone, concrete or brick surrounds glazing with putty or fixed with beads complete all as specified and directed. |
| 82 | S&F in repairs heavy duty Stainless steel (Grade 304) curtain rods 20 to 25mm dia complete all as specified and directed. |
| 83 | S&F in repairs Stainless steel (Grade 304) brackets (Open ends) suitable for curtain rods of 20 to 25mm dia complete all as specified and directed. |
| 84 | S&F in repairs Stainless steel (Grade 304) brackets (Dead ends) suitable for curtain rods of 20 to 25mm dia complete all as specified and directed. |
| 85 | S&F mild steel 300mm, ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and directed. |
| 86 | S&F in repairs mild steel 300mm, ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and directed. |
| 87 | Taking up or down 15 mm dia steel tubing & connections including and removal to store complete all as specified and directed. |
| 88 | Taking up or down 20 mm bore tubes & connections including and removal to store complete all as specified and directed. |
| 89 | S & F 15mm bore of tube medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors complete all as specified and directed. |
| 90 | Refixing only 15mm bore of tube medium grade galvanized with all new fittings & fixed complete to walls & ceiling or laid in floors including clearing complete all as specified and directed. |
| 91 | S & F 20mm bore of tube medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors complete all as specified and directed. |
| 92 | Refixing only 20mm bore of tube medium grade galvanized with all new fittings & fixed complete to walls & ceiling or laid in floors including clearing complete all as specified and directed. |
| 93 | Dismantling water tanks any type of capacity complete all as specified and directed. |
| 94 | S&F 500 litre capacity Rotational moulded polyethylene water storage tanks (cylin-drical vertical with closed top) tripple layered white, hoisted and fixed in position, including 20 mm bore Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and directed. |
| 95 | S&F 1000 litre capacity Rotational moulded polyethylene water storage tanks (cylin-drical vertical with closed top) tripple layered white, hoisted and fixed in position, including 20 mm bore Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and directed. |
| 96 | S&F 20mm PTMT nipple suitable for HDPE water tank (minimum weight 45gms) complete all as specified and directed. |
| 97 | S&F in repair PVC (PTMT) float valve, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed suitable for 20mm bore pipe, complete all as specified and directed. |
| 98 | S&F in repair 15mm bore long body Angle cock/stop cock quarter turn fancy type chromium plated screwed down high pressure complete all as specified and directed. |
| 99 | S & F in repair long body stop valve quarter turn 15mm bore fancy type chromium plated with long shank and cup(concealed type) screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 100 | S&F in repair 15mm long body bib taps quarter turn long shank cast copper alloy with crutch or butterfly hadle secrwed for iron piper or for brass ferrule complete all as specified and directed. |
| 101 | S&F in repair Pillar taps quarter turn long body fancy type with capasten head chromium plated screwed down high pressure with without lettered 'Hot' or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed. |
| 102 | S&F for in repair 15 mm swan neck pillar cock chromium plated fancy type screw with iron pipe including all fittings complete all as specified and directed. |
| 103 | S&F in repair, central hole basin mixer with extended spout 350mm long braided connection pipe (without popup) for iron pipe or for unions and fixed to 15mm bore pipe complete all as specified and directed. |
| 104 | Supplying and fixing in repairs cast copper alloy chromium plated wall mixer 3-in-1 system with complete provision and fixing for Overhead Shower with 115 mm Long Bend pipe, CP screwed down high pressure with long screwed both ends for 15mm dia bore GI pipe complete of approved make as per sample all as specified and directed. |
| 105 | Supply & Fixing in repairs vitreous china urinal half stall type with CP spreader white with grating and union for discharge pipe, including providing and fixing plug, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement fixing with brackets, flush pipe, grating and union for discharge pipe complete all as specified and directed. |
| 106 | S&F in repairs chromium plated Urinal spreader for fixing with 15 mm dia bore pipe complete all as specified and directed by Engineer-in-charge. |
| 107 | S&F in repairs 15mm bore PVC connection pipe 450/600mm long with PTMT nuts at both ends complete all as specified and directed. |
| 108 | S &F in repair chromium pated shower rose 125mm size with or without swivel joints, any size including fixing to 15 mm bore steel pipe or union complete all as specified and directed. |
| 109 | S & F in repair towel rail 20mm dia chromium plated including 600mm long including brackets, screws and wooden/plastic cleats complete all as specified and directed |
| 110 | S&F in repairs 600mm x 450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC plain building board or commercial ply wood and fixed to wooden plug with chromium plated brass screw and cup washers complete all as specified and directed |
| 111 | S&F in repairs 100 mm dia Stainless steel grating complete all as specified and directed |
| 112 | S&F in repairs 75 mm dia Stainless steel with hole gratingcomplete all as specified and directed |
| 113 | S&F in repairs waste down pipe 32/40mm bore for wash basin/sink complete all as specified and directed |
| 114 | S& F in repair vitreous china squatting pan orissa pattern size 580 x 440mm white, with integral foot rests excluding flushing cistern and flush pipe but including traps as required complete all as specified and directed |
| 115 | S & F in repair vitreous china white wash down water closet pan (pedestal pattern) including white plastic seat cover with CP hinging device and PVC P type trap, including connection to trap, drain pipe, flushing cistern & anti syphonage pipe complete all as specified and directedNote : The cost of traps and plastic seat cover are included in this item. |
| 116 | S & F in repair 10 Ltr capacity PVC valveless syphonic action type flushing cistern low level white with inlet ball valve and brackets, float and handle, L-Bend complete all as specified and directed |
| 117 | S&F in repairs vitreous china wash basin, white, flat back, size 580x450mm excluding taps waste, chain and plug and porcelain stopper but including bracket complete all as specified and directed |
| 118 | Demolition up to 100/75mm bore and breaking up drain pipes (AC/reinforced concrete/salt glazed ) complete all as specified and directed |
| 119 | S & F 110mm bore PVC SWR Pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed |
| 120 | S & F 75mm bore PVC SWR Pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed |
| 121 | S & F 110mm bore PVC SWR Junction single (Single T) equal or unequal complete all as specified and directed |
| 122 | S&F PVC (SWR) bends of 110 mm bore complete all as specified and directed |
| 123 | S&F PVC (SWR) bends of 110 mm bore with access door complete all as specified and directed |
| 124 | S&F PVC (SWR) 110mm bore Junction (single T) equal or unequal complete all as specified and directed |
| 125 | S&F PVC (SWR) bends of 75 mm bore complete all as specified and directed |
| 126 | S&F PVC (SWR) bends of 75 mm bore with access door complete all as specified and directed |
| 127 | S&F PVC (SWR) 110 mm reducers complete all as specified and directed |
| 128 | S&F PVC (SWR) 75 mm vent cowl complete all as specified and directed |
| 129 | S & F in repair 75mm bore PVC (SWR) floor trap,with grating plain/ whole including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed. |
| 130 | S&F as in repair stainless steel plate rack, made out of 0.80mm thick of size 31\\"x36\\"x10\\" complete all as specified and directed. |
| 131 | S&F as in repair sinks with drain board made of stainless steel sink of 1mm thick sheet, kitchen or laboratory with plug washer and waste pipe incl bedding in cement mortar 1:6 on to dwarf wall of including fixing cantilever brackets and connecting unions overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified. |
| 132 | S&F in repair stainless steel 32mm waste coupling suitable for stainless steel sink along with grating complete all as specified and directed by Engineer-In-Charge. |
| 133 | M&L for white cementing to joints WC and floor traps,in bath room or Kitchen and floor traps including removing of grating & re-fixing after application of white cement on inner surface etc, complete all as specified and directerd. |
| 134 | S&F in repair MS framed work such as grills, gratings,guardbar with ends of bars shouldered and or riveted or forged into spikes, framed guard bars and similar work confirming to Fe 410 or Fe 310-0 including dismantling old complete all as specified and directerd. |
| 135 | M & L for repair to RCC Chajjas, roof projection edges ,hanging part of chajjas, edges of chajjas, RCC parapets under the roof / floor slabs with PCC 1:2:4 (using 12.5mm crushed graded agg) incl necessay renforcement 8mm to 12mm TMT bars , form work , MS wire mesh for bounding the concrete on ground required and plaster work in CM 1:3 & periodical services to match with the existing surfaces finishing at any height of buildings etc completed all as specified and directed by Engineer-in-Charge. |
| 136 | Taking down aluminium shutter / sliding door for necessary repair work and re-fixing in position after adjusting or re securing with steel strip if required with replacement of steel screw re threading and fixing on existing devices, resetting or replacing top pivots bottom steel plates etc and resetting or replacing glazing etc for proper function of aluminum door of size n exc 1.5 sqm eachcomplete all as specified and directerd.Note :- Supply only glazing and top pivots etc shall be measured and paid separately. Please Enable Macros to View BoQ information |
| 137 | Taking down aluminium shutter / sliding door for necessary repair work and re-fixing in position after adjusting or re securing with steel strip if required with replacement of steel screw re threading and fixing on existing devices, resetting or replacing top pivots bottom steel plates etc and resetting or replacing glazing etc for proper function of aluminum door of size n exc 1.5 sqm eachcomplete all as specified and directerd.Note :- Supply only glazing and top pivots etc shall be measured and paid separately. Please Enable Macros to View BoQ information |
