|
| 1 | BT RoadClearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, up to a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150 mm in thickness as per MORD technical specification cluase 201.1. & direction of Engineer-in-charge (by manual means). |
| 2 | Dismantling of existing structures like culverts, bridges, rataining walls and other structures comprising of cement concrete including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000m as per technical specification clause 202 and as per direction of the Engineer-in-Charge. |
| 3 | Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5 and as per the direction of the Engineer in charge. |
| 4 | Construction of embankment with approved material obtained from borrow pits with all leads and lifts, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 by mechanical means as per Technical Specification Clause 301.5 and as per the direction of the Engineer in charge. |
| 5 | Providing laying spreading & compacting graded stone aggregate to Wet Mix Macadam(WMM) specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on well prepared sub-base and compacting with smooth wheel roller of 80 to 100kn weight to achieve the desired density including lighting, barricading and maintainance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification Clause 406 . |
| 6 | Construction of granular sub-baseGrading III Material (As per IRCSP:77-2008) Well Graded Granular Sub-Base Material by providing well graded material, spreading in uniform layers with tractor with ordinary grader on prepared surface mixing by mix in place method with rotavator at OMC and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401 of MoRD and as per direction of Engineer-In-Charge. |
| 7 | Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502 of MoRD for low porosity surface. and as per direction of Engineer-In-Charge. |
| 8 | Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503 of MoRD. and as per direction of Engineer-In-Charge. |
| 9 | Providing ,laying and rolling of Mix Seal Surfacing (MSS) close-graded premix surfacing materials of 20mm thickness composed of 11.2mm to 0.9mm (Type-A) or 13.2 mm to 0.9 mm (Typa-B) aggregates using penetration grade bitumen to required line ,grade and level to serve as wearing course on a previously prepared base ,including mixing in a suitable plant ,laying and rolling with as three wheel 8-10KN static roller and finishing to required level and grades as per Techinical specification Clause 509. |
| 10 | Providing,supplying,fitting and fixing of 80mm thick interlocking concrete paver block on compacted river coarse sand free from all organic materials and filling the joints with sand including cutting,corbelling, splays whereever necessary to proper size with cost,conveyance,royalities of all materials and as directed by Engineer-in-chief. |
| 11 | Fine dressing &Turfing including transportation of turfs by mechanical means with all leads & lifts and placing of turfs in position and ramming with thapies including watering and cost of labour & all materials etc. complete as per direction of Engineer - in - charge. |
| 12 | CD WORKS : Earthwork in excavation for foundation of structures upto 3 m depth as per drawing and technical specification Clause 1104 of MoRD including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material and as pr the direction of the Engineer in charge |
| 13 | Fillling sand in foundation trenches as per drawing and technical specification Clause 305.3.9 & as per direction of Engineer in charge |
| 14 | Providing and laying of Type-B(first class) bedding for laying of Hume Pipe on well compacted moorum or approved granular material as per MORD Technical Specification clause 1105(ii) and as per direction of the engineer-in-charge. |
| 15 | Providing and laying reinforced cement concrete pipe NP3 for culverts on cement concrete bedding including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. and as per the direction of the Engineer in charge |
| 16 | 600 mm dia HPC (Single row) |
| 17 | 1000 mm dia HPC (Single row) |
| 18 | 1000 mm dia HPC (Double row) |
| 19 | Prividing & laying Plain Cement Concrete M-15 Nominal Mix (1:2.5:5)in open foundation as per drawings & Technical Specification clauses 802,803,1202 & 1203 of MORD and as per direction of Engineer-In-Charge. |
| 20 | Prividing & laying Plain Cement Concrete M-15 Nominal Mix (1:2.5:5) in substructure as per drawings & Technical Specification clauses 802,804, 805,806, 807,1202 & 1204 of MORD and as per direction of Engineer-In-Charge. |
| 21 | Providing and laying reinforced cement concrete of M-25 grade in Super structure complete as per drawings and technical specifications Clause 800 & 1200 of MoRD and as per the direction of the Engineer-in-charge |
| 22 | Deck slab Dirt wall & Parapet |
| 23 | Supplying, fitting and placing HYSD bar reinforcement in substructure complete as per drawings and technical specification Clauses 1002, 1010 & 1202 and as per the direction of the Engineer in charge |
| 24 | Supplying, fitting and placing HYSD bar reinforcement in superstructure complete as per drawings and technical specification Clauses 1000 and 1200 of MoRD and as per direction of the Engineer-in-Charge. |
| 25 | Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7 and as per the direction of the Engineer in charge |
| 26 | Providing and laying pitching with stone boulders on slopes laid over prepared filter media as per drawing and MORD technical specifications Clause 1300 and as per direction of the Engineer in charge |
| 27 | Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and technical specification Clause 1204.3.8 and as per the direction of the Engineer in charge |
| 28 | Providing and fixing 20mm thick compressible fiber board in expansion joint complete as per drawing and technical specifications including cost convyance taxes of all materials, cost of all labours, T & P required for the work etc.complete and as per direction of the Engineer -in- charge. |
| 29 | ROAD APPURTENANCESProviding and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 and as per the direction of the Engineer in charge |
| 30 | Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing as per Clause 1701.2.2 of MoRD and as per direction of Engineer-In-charge600 mm Equilateral Triangle |
| 31 | Supplying and installing of measurement stones including painting, lettering in accordance with the specifications and as approved by the engineer and as per direction of Engineer-In-Charge and as per clause 1703 of MoRD. |
| 32 | i) Ordinary kilometer stone |
| 33 | ii) 200 mtr Stone |
| 34 | iii) Guard Post (M-20) |
| 35 | Providing and erecting direction and place identification of semi reflective sign boards as per IRC-67 made of 2 mm thick M.S. Sheet duly stove enameled paint white colour in front and grey colour on back with reflective border of 70 mm width and required message, letters, figures with reflective tape of engineering grade as per MORD specifications of required shade and colour. Supported and welded on two nos. 47 mm x 47 mm of 12 SWG square tube of 3050 mm height duly strengthened by 25 mm x 5 mm MS flat iron on edges on back firmly fixed to the ground by means of properly designed foundations with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification Clause 1701 of MoRD. and as per the direction of the Engineer in charge |
| 36 | Providing and fixing of typical PMGSY logos made of 1.6mm thick MS sheet duly stove enameled on both side with lettering and printing arrows, border etc.will be painted with ready mixed synthetic enamel paint of superior quality in required shade & colour fixed & supported on 75mmx75mmx6mmM.S.angle 3500mm long firmly fixed to the ground by means of properly foundation with M15 grade c.c. 450x450x600mm ,600mmbelow ground level as per drawings & tech. specification clause 1701 and as per direction of the Engineer -in- charge. |
| 37 | Providing and fixing of typical PMGSY Citizens information board as per MORD specifications and drawing. Three MS Plates of 50 X 5 cm thick, back plate duly welded with 75mm dia steel tubes back on edges as per drawings. The lower & upper plate will be welded with MS flat iron frame of 50mm x 5mm. The steel tubes duly embeded in cement concrete M-15 grade blocks of 600mm x 600mm x 750mm below ground level. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per Clause 1701 and Annexure 1700.1 of MORD Specification for Rural roads including cost,conveyance,royalty, taxes, labour and T&P required for the work and as per direction of Engineer-in-charge. |
| 38 | Maintenance Routine Maintenance after completion of construction works 1st Year |
| 39 | 2nd Year |
| 40 | 3rd Year |
| 41 | 4th Year |
| 42 | 5th Year Please Enable Macros to View BoQ information |
