|
| 1 | Clearing compound premises of shurbs, plants, jungles etc. by cutting and removing as directed (Specific permission of Engineer-in-Charge prior to execution will be necessary). (Payment to be made on area cleared) |
| 2 | Surface Dressing of the ground in any kind of soil including removing vegetation inequalities not exceeding 15cm depth and disposal of the rubbish within a lead upto 75 m as directed. |
| 3 | Earthwork in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sand stone) including removing, spreading or stacking the spoils within a lead of 75 Mtr. As directed. The item includes necessary trimming the side of trenches, leveling, dressing and ramming the bottom, bailing out water etc. as required complete.a) Depth of excavation not exceeding 1500 mm. |
| 4 | Earthwork in filling in foundation trenches or plinth with good earth in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete.i) With earth obtained from excavation of foundation.(Payment to be made on the basis of measurement of finished quantity of work.) |
| 5 | Filling in foundation or plinth by silver sand in layers not exceeding 150 mm. as directed and consolidating the same by thorough saturation with water ramming complete, including the cost of supply of sand. (Payment to be made in measurement of finished quantity.) |
| 6 | Single brick flat soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with powdered earth or local sand. |
| 7 | Cement concrete with graded stone ballast (40 mm. size) excluding shuttering in ground floor. (Pakur Variety).a) 6 : 3 : 1 proportion. |
| 8 | Ordinary Cement Concrete M 15 (mix 4:2:1) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement, if any, in ground floor, as per IS 456 – 2000.i) Pakur variety. |
| 9 | Ordinary Cement Concrete (mix 3:1.5:1) M-20 with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement, if any, in ground floor, as per IS 456 – 2000.i) Pakur variety. |
| 10 | Hire and labour charges for shuttering with centering and necessary staging up to 4mtr. using approved stout, props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams, columns, lintels, curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor).a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge. |
| 11 | f) 25 mm to 30 mm shuttering without staging in foundation. |
| 12 | Supplying and laying Polythene Sheet (150gm./ sqm.) over damp proof course or below flooring or roof terracing or in foundation trenches. |
| 13 | Reinforcement for reinforced concrete work in the all sorts of structures including distribution bars, stirrups, binders etc. including supply of rods, initial straightening & removal of loose rust (if necessary),cutting to requsite length, hooking & bending to correct shape, placing in proper position & binding with 16 gauge black annealed wire at every intersection,complete as per drawing & direction. For works in foundation, basement and upto roof of ground floor / upto4 m. i) Tor steel (JSW/JSPL/SHYAM/SRMB/BMASL/ELECTROSTEEL/SSL)For work in foundation and upto to ground floor roof. |
| 14 | Brick work with 1st. class bricks in cement mortar. (6:1)a) In foundation and plinth. |
| 15 | 125mm. thick brick work with 1st. class bricks in cement mortar (4:1)a) In ground floor. |
| 16 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints or roughening of concrete surface, including throating nosing and drip course where necessary.i) With (1:6) cement mortar.a) 20 mm thick plaster. (Ground floor). |
| 17 | 15 mm. thick plaster . In ground floor. |
| 18 | 10 mm thick plaster. (Ground floor). |
| 19 | ii) M.S. integrated grill as per approved design integrated with steel window or ventilator, joints continuously welded with M.S. flats and bars. |
| 20 | Supplying best Indian sheet glass panes set in .. with nails and putty complete. (In all floors for internal wall.. for external wall).(i) 4 mm thick (weighing 7.4 kg/Sq.m) |
| 21 | Supplying solid flush type doors of commercial quality, the timber frame consisting of top and bottom rails and side styles of well seasoned timber 65mm wide EACH and the entire frame fitted with 37.5mm wide battens places both ways in order to make the door of solid core and internal lipping with Garjan or similar wood vveneers using phenol formaldehyde as glue etc. complete, including fitting, fixing shutters in position but excluding the cost of hinges and other fittings . 35 mm thick shutters (single leaf)--(i) In Ground Floor |
| 22 | Supplying, fitting and fixing fibre reinforced polymer (FRP) Composite door frame as per approved section with glass fibre reinforced plastic moulded skins and a special sandwich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science and Technology (DST) to safisfy IS: 4020 door testing performance criteria..--(ii) 66mm x 70mm I) In Gropund Floor |
| 23 | Supplying, fitting & fixing fibre reinforced polymer (FRP) Composite door shutters as per approved design with glass fibre reinforced plastic moulded skins and a special sandwich core, so as to impart monolitaheic composite structure as per approved technology of Department of Science and Technology (DST) to satisfy IS:4020 door testing performance criteria.----(i) 32 mm thicki)In ground floor. |
| 24 | Supplying, Fitting & Fixing Factory made P.V.C. door frame of size 50 mmx47 mm with a wall thickness of 5 mm, made out of extruded 5 mm, PVC sheet miter cut at two corners and joined with two nos of 1.5 mm long brackets of 15 mm x15 mm M.S. square tube. The two vertical door profiles are to be reinforced with 19 mmx 19 mm M.S. Square tube of 19 gauge, weather seal to be provided through out the frame. The door frame shall be fixed with the wall using 65/100 mm long M.S. Screws through the frame by using P.V.C fasteners. A minimum of 4 Nos ofscrews to be provided for EACH vertical member and minimum 2 Nos for horizontal member etc. complete as per Manufacturer‟s specification and direction of Engineer-in-Charge. |
| 25 | Supplying, Fitting & Fixing 30 mm thick Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19 mmx19 mm for styles, top and bottom rails, M.S. frame shall have cost of steel primers of approved make and manufacture, M.S. frame covered with 5 mm th. heat moulded PVC “C” channel of size 30 mm th, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on either sides forming styles; and 5 mm th. 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm tapered in 45 degree on the inner side to form top & bottom rail and 115 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of the panel with 10 mm (5 mmx2) th.,20 mm wide cross PVC sheet as gap insert for top rail and bottom rail. Paneling of 5 mm th. both side PVC sheet to be fitted in the M.S. frame welded/sealed to the styles &rails with 7 mm (5 mm+2 mm) th.x15 mm wide PVC sheet beading on inner side and joined together with solvent cement adhesive. An additional 5 mm th. PVC strip of 20 mm which is to be stuck on the interior side of the “C” channel using PVC solvent adhesive etc. complete excluding all necessary hardwares as per direction of Engineer-in-charge |
| 26 | Labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium sections for the following units:- (A) Partly glazed and partly panelled partition or fixed glazing made of extruded and anodised alloy aluminium sections, fabrications after cutting to proper shape and size, drilling and aligning fitted with inbuilt locking arrangement cutting the glass / board (prelaminated / particle / block) to requisite shape and size moulding the edges fitted and fixed glazing clips and dry set neoprine /EPDM gasket, along with all other necessary arrangements for fixing the partition to walls, floors, beams,columns polysulphide sealant for water proofing if necessary complete in all respect as per drawing and specifications and direction of the Engineer in charge.The rate includes the hire charge of all tools and plants, adhesive,joineries such as screw, fastener but excluding the cost of extruded aluminium sections, EPDM gasket, glass, board, glazing clips, locking arrangement, etc.I) For partitions using section of size:a) 63.50 mm x 38.10 mm. i) in Gr floor |
| 27 | Hydraulic door closer of approved quality as per I.S.I. standard fitted and fixed complete. (b) Medium (I.S.I. size 2) |
| 28 | Supplying, fitting and fixing PVC pipes of approved makeof (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket reducing tee, short piece etc. fitted with holder bats clamps, including, cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) PVC Pipes(Dia)( I )20 mm Dia |
| 29 | 25 mm Dia |
| 30 | 40 mm Dia |
| 31 | Supplying, fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg per sq. cm. (for water lines only)a) 40 mm. dia. |
| 32 | b) 25 mm. dia. |
| 33 | Supplying, fitting and fixing bib cock or stop cock (i) Chromium plated Stop Cock (Equivalent to Code No. 513(A) & 513(B) & Model - Tropical / Sumthing Special of ESSCO or similar brand |
| 34 | Chromium plated Bib Cock with wall flange (Equivalent to Code No. 5047 & Model - Florentine of Jaquar or similar brand). |
| 35 | Supplying, fitting and fixing pillar cock of aooroved make.a) (i) CP Pillar Cock - 15mm dia(Equivalent to Code No. 507 & Model - Tropical / Sumthinhg Special of EESCOor similar brand). |
| 36 | Wash basin white vitreous china of approvedmake (without fittings) supplied, fitted and fixed in position on 75mm X 75mm X 75mm. Wood blocks and C.I. brackets including two coats of painting of C.I.brackets.(ii) 550 mm X 400 mm. |
| 37 | Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75 mm. x 75 mm. X 75 mm. wooden blocks complete..(ii) 470 mm X 280 mm X 340 mm |
| 38 | Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specificatioons with P.V.C. fittings completre, C.i. brackets including two coats of painting to bracket etc. |
| 39 | Supplying,fitting and fixing 32 mm dia. Flush Pipe of approved make with necessary fixing materials and clamps complete i) Polythene Flush Pipe |
| 40 | Supplying, fitting and fixing best quality Indian make mirror 5.5 mm. thick with silvering as per I.S.I specifications supported on fiber glass frame of any colour, frame size 550mm x 400mm. |
| 41 | Supplying fitting & fixing UPVC Pipes A type and fitttings conforming to IS 13592-1992 with all necessary clamps, nails including making holes in walls, floors etc cutting trenches in any soil through masonary concrete structures etc, if necessary, and mending good damages including joining with jointing materials.(for rain water draining) A.) UPVC Pipes of 110 mm dia. |
| 42 | B) Plain Tee (UPVC), 110mm dia. |
| 43 | C) UPVC Shoe, 110mm dia. |
| 44 | D) Bend 87.5 degree of 110mm dia. |
| 45 | Stripping off worn out plaster and raking out joints of walls, ceillings etc. upto any height and in any floor including removing rubbish and stacking anywhere within the compound as directed. |
| 46 | Uprooting and removing plants from the surface of walls parapet etc and making good damages. (Repairing of damages to be paid separately). (a) Small plant of girth of exposed stem upto 75 mm. lift upto 6 mtr. |
| 47 | Cleaning the exposed reinforcement preferably upto full diameter by wire brush, applying two coats of polymer based rust removing compound left for 24 hours, removing the coating and then applying two (2) coats of polymer modified anti corrosive protective coating formulated to inhibit the corrosion of reinforcement as per manufacturer's specification] |
| 48 | Removing old paint from blistered painted surface of steel or other metal by chipping including scraping and cleaning and exposing the original surface. |
| 49 | Cleaning and removing paint mark from glass pane with spirit and removing strains etc. |
| 50 | Repairing crack in wall by cement grouting (1 : 2) including widening the crack on the surface (into V section) cleaning and packing the same with cement mortar (1 : 2) and finishing off to match with adjacent surface. (Cement-69 Kg/100 m) |
| 51 | Removal of rubbish,earth etc. from the workingsite and disposal of the same beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge |
| 52 | Removing sludge from septic tank, soak well etc. by methor labour including disposal of the same outside the compound as directed. c) Upto 50 users:-ii) Beyond a lead of 150 metre and outside the Municipal limit |
| 53 | Cleaning silt of inspection pit. |
| 54 | Reparing collapsible gate by cutting out all rivets as necessary reassambling all members including welding pieces of channels, sraightening bent bars and rivetting with new rivets and fitting in position and painting two coats. |
| 55 | Easing and oiling, cleaning collapsible gate and repairing to locking arrangements. |
| 56 | Labour for taking out rolling shutter (only shutter portion) dismantling by parts for repair or (replacement of damaged parts only), rehanging and refitting the same in position after necessary repairs |
| 57 | Easing and oiling, cleaning rolling shutters excluding repair toinside locks. |
| 58 | Neat cement punning above 1.5mm. thick in wall, dado, window sills, floor etc.(Note : Cement 0.152 cum. per 100 sqm.) |
| 59 | M.S. structural works in columns, beams etc. with simple rolled structural members (e.g. joists, angles, channel sections) conforming to IS : 226, IS : 808 & SP (6) : 1964 connected to one another with bracket, gusset, cleats as per design, direction of Engineer-in-Charge complete including cutting to requisite shape and length, fabrication with necessary bolting, metal arc welding conforming to IS : 816 1956 & IS : 1995 using electrodes of approved make and brand conforming to IS : 814 – 1957, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hires charges of all tools and plants and labour required for the work including all incidental charges such as electricity charges, labour insurance charges etc.i) For structural members of specified sections weighing less than 22.5 Kg./m |
| 60 | Priming one coat on steel surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 61 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface if necessary. a) On steel or other metal surface. With other than hi-gloss of approved quality.i) Two coats (with any shade except white). |
| 62 | Applying Exterior grade Acrylic primer of approved quality and brand on plastered or concrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface thoroughly, complete as per manufacturer’s specification and as per direction of the EIC.a) One coat.i) In ground floor. |
| 63 | Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer’s specification and as per direction of EIC to be applied over acrylic primer as required. The rates includes cost of materials, labour, scaffolding and all incidental charges but excluding the cost of primer.a) Premium 100 % Acrylic Emulsion i) Ground floor (Two coats) |
| 64 | Applying Interior grade Acrylic Primer of approved quality and brand on plastered or concrete surface old or new surface to receive distemper / acrylic emulsion paint including scrapping and preparing the surface thoroughly, complete as per manufacturer's specification and as per direction of E.I.C One coat. i) Water based interior grade acrylic primer. |
| 65 | Applying Acrylic emulsion paint of approved make and brand on walls and ceiling including sand papering in intermidiate course including putty (two coats). Standard Quality. |
| 66 | Dismantling all types of masonry excepting cement concrete plain or reinforced, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m. In ground floor including roof. |
| 67 | Dismantling R.C floor, roof, beams etc including cutting rods and removing rubbish as directed within a lead of 75 m including stacking of steel bars. In ground floor. |
| 68 | Supplying Crushed stone ( Trap stone ) shall be of 40 mm ( Ungraded ) nominal size. (40 mm size). Pakur Variety.(Payment will be made on basis of measurement after deduction of shrinkage, shinkage). (Washing should be done before spreading of gravels over base). |
| 69 | Labour for picking up existing gravels / stone metals,surface to average depth including screning and stacking the gravels/ stone metals depth upto 100 mm by mannual means. |
| 70 | Labour for spreading gravels/ stone metals in layer upto 100mm.thick as per direction. Please Enable Macros to View BoQ information |
