|
| 1 | M&L for scraping of old paint/rust etc with wire brush from rolling shutter and painting one coat of red oxide primer and two coats of synethic enamel paint all as specified and directed by Engineer-in-Charge. |
| 2 | S&F in repair MCCB AC 415 volts, 63 Amp rating, breaking capacity of 25 KA, adjustable thermal and fixed magnetic with two side spreader thermal kit, 4 Pole complete all as specified and directed |
| 3 | S&F in repair MCCB AC 415 volts, 100 Amp rating, breaking capacity of 16 KA, adjustable thermal and fixed magnetic, with two side spreader thermal kit, 4 Pole complete all as specified and directed. |
| 4 | S&F in repair MCCB AC 415 volts, 125 Amp rating, breaking capacity of 16 KA, adjustable thermal and fixed magnetic, with two side spreader thermal kit, 4 Pole complete all as specified and directed. |
| 5 | S&F in repair MCCB AC 415 volts, 160 Amp rating, breaking capacity of 36 KA, 4 Pole complete all as specified and directed. |
| 6 | S&F in repair MCCB AC 415 volts, 200 Amp rating, breaking capacity of 36 KA, adjustable thermal and fixed magnetic, with two side spreader thermal kit, 4 Pole complete all as specified and directed. |
| 7 | S&F in repair MCCB AC 415 volts, 250 Amp rating, breaking capacity of 36 KA, 4 Pole complete all as specified and directed. |
| 8 | S&F in repair MCCB AC 415 volts, 315 Amp rating, breaking capacity of 36 KA, 4 Pole complete all as specified and directed. |
| 9 | S&F in repair MCCB AC 415 volts, 350 Amp rating, breaking capacity of 36 KA, 4 Pole complete all as specified and directed. |
| 10 | S&F in repair MCCB AC 415 volts, 400 Amp rating, breaking capacity of 36 KA, 4 Pole complete all as specified and directed. |
| 11 | S&F in repair of ACB 4 Pole, 415 V, with microprocessor release IPR3+ (LSIG +LCD Display+Thermal Memory+ zone Selectivity+Current & voltage Measurment+Advance Protection+over tempeture protection) capacity 630 Amps 50 KA , Manual Drawout type in existing panel complete all as specified and directed. |
| 12 | M&L for earthing complete with galvanised steel earth plate electrode 60×60cm×6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron strip 25x4mm earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 connected to earthing test point including testing on completion including watering GI pipe 20mm bore medium grade, 15mm bore light grade GI pipe for protection of earth lead including provision of concrete pit in PCC (1:3:6) type C1 (using 20mm graded crushed stone aggregate), pre-cast RCC (1:2:4) type B1 (using 20mm graded crushed stone aggregate) cover slab 54cm x 54cm x 5cm including 8mm dia TMT bars both ways @ 15cm centre to centre with one handle for lifting made out of 8mm dia MS bar, funnel & wire mesh, excavation and earth work in any type of soil complete including dismantling existing all as specified and directed by Engineer-in-Charge. |
| 13 | S&F earth continuity conductor or main earthing lead fixed to wall/on batten or reces or chases or buried in ground or drawn in condit/pipe or fixed to poles or any other indicated situation for loop earhing etc as required galvanised iron strip of size 25 x 4mm all as dircted by Engineer-in-Charge |
| 14 | Supplying, installing, testing of LT control Bus Bar chamber out door type with neoprene rubber gasket and locking arrangement vermin/dust / weather proof, self ventilation with wire mesh at suitable interval totally enclosed, busbar chamber, fullly comparted type, front openable hinged with locking arrangement and Rear and front door with L drop Locking arrangement made out of 3.15 mm thick CRCA sheet duly powder coated paint, properly welded and connecting the incoming / out going feeders by providing cable glands and cable lugs complete all as specified and directed comprising of following accessories.(i) MCCB 250 Amp 4 pole, 36KA 415 volt AC with adjustable thermal and adjustable magnetic setting including spreader. (ii) Bus Bars : 320 Amp TPN aluminium busbars (iii) Volt meter 0 to 500 volts digital type with slector switch - 1 No(iv) Ampere meter 0 to 200 Amp digital type slector swtich - 1 No (v) LED Phase indicator lamp Set of three. (vi) All connections from MCCBs to bus bar & bus bar to MCCB shall be made with suitable size of aluminium strip thimble lugs. (vii) All acessories prewired with copper conductor cable single strand PVC insulated with copper thimbe lugs etc all as specified and directed(viii) Above all complete in all respect including installation of panel and frame pedestal legs made 50x50x6mm of length 900 mm x 450mm below the ground and 450 mm above the gound level grouted in PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) . Please Enable Macros to View BoQ information |
| 15 | Supplying, installing, testing of LT control Bus Bar chamber out door type with neoprene rubber gasket and locking arrangement vermin/dust / weather proof, self ventilation with wire mesh at suitable interval totally enclosed, busbar chamber, fullly comparted type, front openable hinged with locking arrangement and Rear and front door with L drop Locking arrangement made out of 3.15 mm thick CRCA sheet duly powder coated paint, properly welded and connecting the incoming / out going feeders by providing cable glands and cable lugs complete all as specified and directed comprising of following accessories.(i) MCCB 250 Amp 4 pole, 36KA 415 volt AC with adjustable thermal and adjustable magnetic setting including spreader. (ii) Bus Bars : 320 Amp TPN aluminium busbars (iii) Volt meter 0 to 500 volts digital type with slector switch - 1 No(iv) Ampere meter 0 to 200 Amp digital type slector swtich - 1 No (v) LED Phase indicator lamp Set of three. (vi) All connections from MCCBs to bus bar & bus bar to MCCB shall be made with suitable size of aluminium strip thimble lugs. (vii) All acessories prewired with copper conductor cable single strand PVC insulated with copper thimbe lugs etc all as specified and directed(viii) Above all complete in all respect including installation of panel and frame pedestal legs made 50x50x6mm of length 900 mm x 450mm below the ground and 450 mm above the gound level grouted in PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) . Please Enable Macros to View BoQ information |
