|
| 1 | Clean removal of cement plaster from walls and clear it away from the site with required labours ete..complete as per standared specification |
| 2 | Plastering the surface of walls with Cement Mortar 1:3 (One cement and Three plastering sand), 12mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc., complete complying with standard specification and as directed by the departmental officers. |
| 3 | Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc. complete complying with standard specification and as directed by the departmental officers. |
| 4 | Supply and fixing of 450mm(18\\") sweep (lightduty) AC exhaust fan complete with necessary wall opening and making good of the wall (SD 118) |
| 5 | Supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550 X 400 mm with a pair of cast iron brackets, including cost of 15mm diametre brass chromium plated piller tape,32 mm diametre C.P. Waste union, 32 mm diametre P.V.C. waste pipe with rubber plug and chain, 15mm diametre G.M.wheel valve, 15mm dia brass nipple, 15mm dia nylon connections etc., including fixing the wash hand basin in the wall in position with a pair of C.I. brackets with teak wood plugs and screws and giving necessary water supply connection and paintiung the brackets with two coats of paint over a primimg coat of anticorrosive paint including testing for leackage etc., complete complying with standard specifications |
| 6 | Supply and Fixing of 20W 4 Feet LED Fitting with LED |
| 7 | Paving the floor with best quality vitrified Tiles of following size and variety conforming IS 15622 with water absorbtion less than 0.08% of approved colour and shade laid over cement mortar bed of 20mm thick in cement mortar 1:3 (one cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer in all floors and the top pointed with Water Resistant Tile Epoxy Grout etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works) |
| 8 | Supply and fixing of 1200mm (48\\") sweep AC ceiling fan complete with stepped electronic 300W regulator with 1metre down rod with fan clamp with side plates and cross arm of size 450mm (18\\") |
| 9 | Supplying, fabricating and fixing in position of Alumi.Anod.natural colour matt finish door half glazed and half PLB board using 12 mm thick PLB board and 5.5 mm thick glazed door using rectangular Alu.Box section of following sizes for frame and shutter with necessary accessories such as rubber beading, Al. Clips, Best double action floor springs, Aluminium Handles on both sides,floor stopper,Tower bolt, Locks and glass including all materials, Labour, power consemption charges required for fabrication if necessary chipping, dismantling making necessary holes in RCC Coloums, Beams or Masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing etc.,complete. The Alumi. surface must be anodised with matt finish under electrically controlled condition in accordance with IS specification 1868 / 1962 of Anodic filthickness of not less than 15 Microns (Fifteen) for all sections. |
| 10 | Supplying and fabrication and fixing in position of anodised natural colour matt finish sliding window in two track in all floors with following sizes. All the three shutters with slinding arrangements, the bottom section should have Gutter arrangements so as to drain the water entering and made with extruded aluminium section for outer frames as shown below with necessary accessories such rubber beading. Aluminium clips, rubber beading,handle and fixing 4mm thick clear sheet glass including all required for fabrication etc., complete.Necessary dismantling making holes in RCC columns, beams, masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing as directed by the departmental officers.The Al.Surfaces is to be anodised with matt finish under electrically condition in accordance with ISI 1868/1962 specification for an average anodic film thick of not less than 15 microns. |
| 11 | Painting Old Plastered Wall Surface with One finishing coats of ready mixed (Emulsion) of approved quality and colour over the existing wall in all floors etc., complete complying with standard specification and as directed by the departmental officers.(The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.) |
| 12 | Painting Old iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with One coats of best approved first quality and colour of synthetic enamel paint in all floors etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.) |
| 13 | Wiring with 2x4sq.mm .PVC insulated SCunsheathed FRLS copper cable conducto cable of 1100V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with 150mmx100mmx75mm MS switch box for 15A 3 pin non interlocking CS plug with painting of suitable colour with continuous earth wire connection by 4sq.mm copper wire for open power plug point |
| 14 | Wiring with 2x1.5 sq.mm .PVC insulated SCunsheathed FRLS copper cable conducto cable of 1100V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with 150mmx100mmx75mm MS switch box for 15A 3 pin non interlocking CS plug with painting of suitable colour with continuous earth wire connection by 4sq.mm copper wire for open plug point |
| 15 | 1. SS Rice Plate -Not Less than 30cm Dia |
| 16 | 2. SS Tumbler Not Less than 4inch |
| 17 | 3. Thalippu Karandi Not Less than 50cm |
| 18 | 4. SS Deep Karandi No:4 Not Less than 27cm |
| 19 | 5. SS Deep Karandi No:5 Not Less than 32cm |
| 20 | 6. SS Sambar Bucket – Not Less than 25cm, 6.500 kg |
| 21 | 7. SS Water Drum – Not Less than 35cm ,3.140 kg |
| 22 | 8. SS Sambar Mug Not Less than 2.65 ltr |
| 23 | 9. Plastic Kudam Not Less than 14 ltr |
| 24 | 10. Aluminium Texi – 8.780 kg Not Less than 75cm L |
| 25 | 11. Aluminium Texi Not Less than 75cm L |
| 26 | 12. Aluminium Texi Lid – 1.080 kg Not Less than 70cm L |
| 27 | 14. SS Adukku – 1.300 kg Not Less than 30cm Dia |
| 28 | 15. Office Table ASI 3004 Not Less than 0.90m H |
| 29 | 16. Office Chair Not Less than 19 inch S type Wire Chair |
| 30 | 17. SS Oil Thookuvalli Not Less than 2.25 Ltr, 20cm H |
| 31 | 18. Aluminium Karandi – 1.590 kg Not Less than 1.2m L |
| 32 | 19. SS Hot Box Not less than50Ltr |
| 33 | 20. Wooden Arivalmanai |
| 34 | 21. SS Stool Not Less than 54x30x30 cm |
| 35 | 22. SS Knife Not Less than 20cm |
| 36 | 23. Plastic Tray Not Less than 24cmx20cmx5cm |
| 37 | 25. Steel Bero Not Less than 2 door 5.5 ft |
| 38 | 26. Plastic Toilet Brush |
| 39 | 27. SS Karandi Sattuvam – 1.080 kg |
| 40 | 28. Thread Mat Not Less than 50x40cm |
| 41 | 31. SS Water Jug No:5 Not Less than 1 ltr |
| 42 | 32. SS Adukku – 2.400 kg Not Less than 28cm dia |
| 43 | 33. Hollow Mat Not Less than 60x40 cm |
| 44 | 34. Mop Heavy Duty 555 |
| 45 | 35. Roof Cleaner |
| 46 | 36. SS Tope Cover – 0.920 kg Not Less than 0.32m L |
| 47 | 37. SS Half Adukku – 0.900 kg Not Less than 30cm H |
| 48 | 39. Plastic Moram – 50cm L |
| 49 | 40. Plastic Mug –Not Less than 1.5 Ltr |
| 50 | 41. Plastic Dustbin – Not Less than 9Litr |
| 51 | 42. Aluminium Dub – 3.600 kg Not Less than 56cm Dia |
| 52 | 43. Plastic Bucket Not Less than 10Ltr |
| 53 | 44. Aluminium Anna Koodai – Not Less than 38cm Dia |
| 54 | 45. Aluminium Lid – Not Less than 65cm Dia |
| 55 | 10 padi aluminium vattai with lid |
| 56 | 5 padi aluminium vattai with lid |
| 57 | 2 padi aluminium vattai with lid |
| 58 | Ms fry pan of standard size Not Less than 45Cm Dia |
| 59 | Silver vessels for butter Not Less than 40cm Dia & 60cm H |
| 60 | Steam boiler service of gasket,bolt nut replacing and servicing of all rice vessels including cost of labour charges as per standared specification |
| 61 | Gas line alteration and burner service work including cost of labour charges as per standared specification |
| 62 | Supply and Delivery of Tilting grinder of 15 lts capacity including fixing and transporting charges as per standared specification |
| 63 | Supply and Delivery of Chest cooler of 380 lts (Double door chest cooler) including fixing and transporting charges as per standared specification |
| 64 | Supply and Delivery of High speed mixie of 9 lite commercial mixe make with complete accessories including fixing and transporting charges as per standared specification |
| 65 | Supply and Delivery of Weight machine to weigh 100kg with complete accessories including fixing and transporting charges as per standared specification |
| 66 | Grinder service ( motor checkup,belt replacing ,wiring checkup and others) including cost of labour charges as per standared specification |
| 67 | Ro plant general service (replacing main filter and mandatorycheckups) including cost of labour charges as per standared specification |
| 68 | Provision for GST 18% Please Enable Macros to View BoQ information |
