|
| 1 | SUB-STATION PART:- 33 KV Pin Insulator |
| 2 | 33 KV Pin with nuts |
| 3 | A.C.S.R. Panther conductor for swichyard |
| 4 | PG Clamp Panther to Panther Conductor |
| 5 | 33 KV Disc Fitting for Panther conductor |
| 6 | 33 KV Disc Insulator for Panther conductor |
| 7 | 33 KV Line Isolator. |
| 8 | 33 KV Bus Isolator. |
| 9 | Structure for Line & Bus Isolator. with Plinth & Foundation |
| 10 | 33 KV Post Insulator |
| 11 | Structure for Post Insulator with Plinth & Foundation |
| 12 | 33 KV Lightening Arrestors |
| 13 | Structure for Lightening Arrestors with Plinth & Foundation |
| 14 | 33/11 KV Transformer 5 MVA |
| 15 | Plinth and foundation of Power T/F as per approved drawing |
| 16 | 90 Lbs. Rail pieces for T/F Wt. 44.6 Kg/Mtr.@Rs. 22.10 Per Kg. |
| 17 | 33 KV VCB 1250A, 750 MVA with Structure |
| 18 | Control panel I/C for 33 KV single T/F |
| 19 | Control panel I/C for 33 KV double T/F |
| 20 | CT 400/200/1-1A |
| 21 | CT 200/100/1-1A |
| 22 | CT Steel structure with Plinth & Foundation |
| 23 | 33 KV PT, 33 KV/110V-1 Phase |
| 24 | Structure for above PTs with Plinth & Foundation |
| 25 | Plinth & Foundation of 33 KV VCB |
| 26 | 33 KV Fuse Set |
| 27 | Structure for Fuse Set with Plinth & Foundation |
| 28 | M.S. Angle (50x50x6) mm for Stair of Fuse set |
| 29 | 11 KV SWITCH GEARS VCB:- (i) Incoming VCB 600/300/5A, 350MVA, I /C |
| 30 | (ii) Outgoing VCB 200/100/5A, 350MVA |
| 31 | (iii) Bus coupler 350 MVA |
| 32 | 11KV 3 Core XLPE Cable:- (i) 3 × 300 Sq.mm |
| 33 | (ii) 3 × 185 Sq.mm |
| 34 | Fabrication and erection of cable support made of two pieces of G.I. 65x65x6 mm. 4.0 mtr. Long 1.0 m grouted in depth, joined to each other by means of 5 Nos. M.S. flat 50x6 mm. pieces of size 150 mm. long each by welding at equal intervals as per drawing and grouting in a block of size 300x300x700 mm. complete with two coats of Aluminium paint. This includes providing of four nos. G.I. clamp made of G.I. flat for holding the cable including Nuts & Bolts. |
| 35 | Laying of 11KV Cable Including cost of sand and Bricks. |
| 36 | 11KV Cable jointing kit. Heat Shrinkable:- 300 Sq.mm Indoor |
| 37 | 300 Sq.mm Outdoor |
| 38 | 185 Sq.mm. Indoor |
| 39 | 185 Sq.mm. Outdoor |
| 40 | Making of 11 KV Cable Box and mounting on Switch Gear and Transformer |
| 41 | 24 V Battery with Battery Charger and Cabinet. |
| 42 | Armoured Copper Control cable:- 4 × 2.5 Sq.mm. |
| 43 | 2 × 2.5 Sq.mm. |
| 44 | Earthing of Sub-Station:-(As per RESSPO Schedule) (i) Outdoor Equipment (Earth Mat) |
| 45 | (ii) Indoor Equipment (Earth Mat) |
| 46 | Pipe Earthing of Power Transformer by way of boring and lowering of \\"B\\" class G.I. pipe 50 mm. dia. Into the ground up to the water lever to the lower end of which a solid copper con approx 9 inches long and 750 gram in weight provided and screwed in connecting and bringing out continuous copper wire 8 SWG from the cone to the ground surface where it will be bolted to the G.I. Earth strip for transformer neutral connection. The earth strip will be welded to the G.I. pipe. The work also includes cap and clamp for pouring water, the cost of all material with all labour and T&P etc. complete in all respect. |
| 47 | Chemical Pipe Earthing as per DVVNL approved G.T.P. |
| 48 | Fabrication and grouting of G.I. Channel 100x50x6 mm. in L shape & in proper size and alignment to provide support for the two separate Earthing strips for power transformer neutral including supply & fixing of two nos. flexible copper bonds for neutral Earthing. The work also includes painting of G.I. Channel with two coats of aluminium paint. |
| 49 | 11/0.4 KV, 63 KVA Transformer. |
| 50 | L.T. PVC Cable Al. 3.5 × 70 Sq.mm . |
| 51 | SWITCH YARD LIGHTING ARRANGMENT:- Stone Pad -6 NoPVC Cable 2×10 mm2 armor for switch Lighting -200 Mtr PVC conduct pipe for PVC cable- 150 Mtr Change Over Main Switch 63 Amp. for three phase supply -01 No. Concreting of supports - 6 No. Sun mica Board Including (MCB Box - 1 no., three phase four wire- 2 No., Red yellow Blue Bulb including Holder and wiring)- 1 Job LED Light 100 W (ISI Mark) -8 No. 15 Amp. LED Light Control Switch Button - 8 No. |
| 52 | Painting of Sub-Station structure & Equipment |
| 53 | Exhaust Fan Complete in every respect for Power T/F |
| 54 | T&P of Substation of switchgears ( Magger 5 KVA Digital type - 1 Nos., Screw Driver Set., Rinch Paana Set., Nut Boult Opener Complete Tool Kit, 33 KV Hand Gloves- 2Nos., Plier, Conductor Cutter, LED Charge able Tourch, Earth Tester, Earthing Chain, Discharge Rod for Earth of line - 2 No., Hygrow Meter for Check Gravity of Battery Water, Continuity Tester, Tong Tester etc. |
| 55 | Cost of Misc. Items i.e. Rubber Matting 4 No, Single Line Diagram Board of SS, S/S Name Board made by MS Angle 50x5 mm. 3 Mtr. Long with 8 SWG gaze sheet 1.5 Mtr. Length and width and painting of SS Name at control room wall etc. |
| 56 | Fire Fighting equipments including 02 Nos. 4.5 Kg. Co2 Fire Extinguisher potable type and 02 Nos. Foam type Fire Extinguisher potable type |
| 57 | Fire Bucket stand size 1500x1200mm. having M.S. Channel 100x50 mm base with cross triangular bracing of M.S. Angle 50x50x6 mm and base of 100x50 mm. Channel 600 mm long having pipe 25 mm and boxing pipe of size 32 mm. including welded with M.S. hooks rigidly and nicely painted with one coat of red oxide primer & two coat of red enamel paint of best quality. |
| 58 | Fire bucket made of B.P. sheet 20 gage ( conical shape ) having capacity 10 Ltr.- 10” dia with bar handle for hanging of bucket including nicely painted in inner portion with one coat of red oxide primer & two coat of channel white paint & outer side with one coat of red oxide primer & two coat of post office red colour & written work “AAG” in Hindi. |
| 59 | Substation Furniture (4–Chairs,2-Office chair, 2–Table, 1–Steel Bench, 1–Steel Rack Long size) |
| 60 | Survey and lay out of Sub-station |
| 61 | Sundries Charges |
| 62 | Testing & commissioning charges of Substation. |
| 63 | Dismental of existings structures and scraps in premises of Sub-Stations & Dump to Store Mathura. |
| 64 | Paint of 5 MVA Power T/F by compressor machine (2 no. cotting) |
| 65 | 33 KV LINE PART:- PCC Pole 9.0 Mtr. Long |
| 66 | 11M, ST Pole - SP - 55 Galvanised |
| 67 | 13.0 M long, STP Pole |
| 68 | Stone Pad (300x300x75 mm) |
| 69 | 33KV \\"V\\" type Cross arm 100 x 50 x 6 mm, M.s Chaneel |
| 70 | Top-bracket for 33 KV |
| 71 | Clamp for 33 KV \\"V\\" type Cross arm with bolts and nuts |
| 72 | 33KV Pin Insulator |
| 73 | 33KV Pin with nuts |
| 74 | G I Barbed Wire |
| 75 | Aluminium winding wire |
| 76 | Number Plate with clamp and Nut & Bolt |
| 77 | Danger Plate with clamp and Nut & Bolt |
| 78 | Nut Bolt and washer all sizes |
| 79 | The Grouting and making of plinth of the support (1/6 of the full length of the supports) will be done as per norms in the CC 1:4:8 with cement, course sand and brick ballast including back filling and proper ramming.fixing of all clamps and other accessories as per relevant drawing. (i) 9.0 Mtr. Long PCC poles |
| 80 | (iii) 11 Mtr. Long S.T. poles |
| 81 | (iv) 13 Mtr. Long S.T. poles |
| 82 | Connecting Clamp for Stud pole |
| 83 | Armour rod with ferrules |
| 84 | Earthing of Pole by M S Earthing Rod 20 x 2500 mm and 6 SWG earthing wire etc |
| 85 | X- Arm Holding Angle with clam 65x65x6 x 1600 mm. |
| 86 | E-bracket for 33 KV |
| 87 | Aluminium Paint |
| 88 | Red Oxide Paint |
| 89 | Earth wire Clamp |
| 90 | Top Channel 125x65 mm, 3200 mm long |
| 91 | Dropper Channel 100x50mm, 3000 mm long |
| 92 | Holding Clamp for top & dropper channel |
| 93 | M.S. Angle 65x65x6x4300 mm x2 Nos. Bracing set with 4 Nos. Clamps. |
| 94 | Complete Stay (GI Stay Rod 20x1800 mm, stay wire 7/8 SWG, Stay Clamp, Bolt, nut and washer with concrete grouting) |
| 95 | Grouting of Stay Rods 20x1800 mm. including all works of excavation, fixing, tightening & nozzling of stay with the poles and of required tension as per relevant drawing including back filling of earth and proper ramming. |
| 96 | 33 KV Disc Insolator 70 KN B&S type |
| 97 | 33 KV Disc Fitting for dog Conductor 70 KN B&S type |
| 98 | PG Clamp Dog to Dog |
| 99 | ACSR Dog Conductor |
| 100 | Tee off channel 125x65x1600 mm |
| 101 | Holding clamp for Tee off Channel |
| 102 | M.S. Guarding Angle 65x65x6x2300 mm. |
| 103 | M.S. Guarding Angle Holding clamp with nuts and bolts |
| 104 | Eye Bolts |
| 105 | G.I. wire 6 SWG |
| 106 | G.I. wire 8 SWG |
| 107 | Binding wire |
| 108 | Turn Buckle |
| 109 | M+6 Tower 19 Mtr. Long (2500 KG Weight) |
| 110 | Grouting of M+6 Tower with Plingth |
| 111 | HDPE Pipe PE-100 PN-6 dia 160 mm |
| 112 | 33 KV 3x300 sqmm XLPE cable. |
| 113 | 33 KV H/S Jointing Kit 3x300 sqmm |
| 114 | Cable route Marker |
| 115 | G.I. Pipe 160 mm dia |
| 116 | G.I. Pipe Hoding Clamp |
| 117 | Cable Fixing Clamp |
| 118 | Laying of 33 KV Cable in Air |
| 119 | Laying of HDPE Pipe PE-80, PN-6, DN-200mm dia Pipe for laying of 33KV, 3x300Sq.mm, XLPE Cable with HDD (trenchless) method including cable laying. |
| 120 | Digging & laying of 33 KV Cable in tranch with sand & brick |
| 121 | Making of 33 KV J/kit |
| 122 | Chopping of branches of tree |
| 123 | 11 KV LINE PART:- 8.5 Mtr PCC Pole |
| 124 | 11 Mtr STP SP-55 Pole |
| 125 | 13 Mtr STP SP-72 Pole |
| 126 | Stone Pad (300x300x75 mm) |
| 127 | 11 KV \\"V\\" type cross arm 65x65x6 mm, M S Angle |
| 128 | Clamp for 11 KV \\"V\\" type Cross arm with bolts and nuts |
| 129 | F-bracket for 11 KV |
| 130 | 11KV Pin Insulator |
| 131 | 11KV Pin with N&B |
| 132 | G I Barbed Wire |
| 133 | Alluminium Binding wire (5 mm dia) |
| 134 | Number Plate with clamp and Nut & Bolt |
| 135 | Danger Board with clamp and Nut & Bolt |
| 136 | The Grouting and making of plinth of the support (1/6 of the full length of the supports) will be done as per norms in the CC 1:4:8 with cement, course sand and brick ballast including back filling and proper ramming.fixing of all clamps and other accessories as per relevant drawing. (i) 8.5 Mtr. Long PCC poles |
| 137 | (ii) 11 Mtr. Long S.T. poles |
| 138 | (iii) 13 Mtr. Long S.T. poles |
| 139 | Earthing of Pole by M S Earthing Rod 20 x 2500 mm and 6 SWG earthing wire etc |
| 140 | M.S. Nut Bolt and washer |
| 141 | Al Paint |
| 142 | Red Oxide Paint |
| 143 | M.S. Angle 65x65x6x2700 mm Bracing Set with 4 Nos. Clamps. |
| 144 | Top Channel 100x50x6 mm, 2240 mm long |
| 145 | Dropper Channel 100x50mm, 2022 mm long |
| 146 | Holding Clamp |
| 147 | Complete Stay |
| 148 | 11 KV Disc Insulator T&C 45 KN |
| 149 | 11 KV Disc Fitting for T&C 45 KN |
| 150 | PG Clamp for weasel Conductor |
| 151 | 11 KV E- Bracket |
| 152 | MS Angle 65x65x6 mm, 2028 mm. long for G.I. Pipe supporting @5.8 Kg/M |
| 153 | T-off M.S. Channel 125x65x1300 mm. |
| 154 | T-off Channel Holding Clamp with nut & Bolts For PCC Pole |
| 155 | ACSR Raccon Conductor |
| 156 | G.I. Pipe 160 mm Dia. |
| 157 | 11KV TPMO with fixing clamp complete |
| 158 | 11 KV Fuse Set with fixing clamp |
| 159 | 11 KV DO Fuse Set with fixing clamp |
| 160 | Clamp with nut & bolts for (Top channel - 2 + Droper channel - 2 + TPMO - 2 + Fuse set - 2 Nos. + G.I. Pipe support - 2 Nos. ) |
| 161 | 11 KV Lightning arrestor |
| 162 | SMC MCCB Distribution board for 63 KV Transformer |
| 163 | M.S. Gaurding Angle 65x65x6x2300 mm. |
| 164 | M.S. Gaurding Angle holding clamp with nuts and bolts |
| 165 | Eye Bolts |
| 166 | G.I. Wire 6 SWG |
| 167 | G.I. Wire 8 SWG |
| 168 | Binding wire |
| 169 | Turn Buckle |
| 170 | Lug 300 sqmm. |
| 171 | Insultated single lead cable 300 sqmm. |
| 172 | Connecting Clamps |
| 173 | HDPE Pipe PE-100 PN-6 dia 160 mm |
| 174 | 11 KV 3x185 sqmm XLPE cable. |
| 175 | 11 KV H/S Jointing Kit 3x185 sqmm |
| 176 | Cable route Marker |
| 177 | G.I. Pipe 160 mm dia |
| 178 | G.I. Pipe Hoding Clamp |
| 179 | Cable Fixing Clamp |
| 180 | Laying of 11 KV Cable in Air |
| 181 | Laying of HDPE Pipe PE-100, PN-6, DN-160mm dia Pipe for laying of 11KV, 3x185Sq.mm, XLPE Cable with HDD (trenchless) method including cable laying. |
| 182 | Digging & laying of 11 KV Cable in loop trench with sand & brick |
| 183 | Making of 11 KV J/kit |
| 184 | Chopping of branches of tree |
| 185 | Processing and documentation fees for Railway Department |
| 186 | Carriage of following material from Center Store to Site SUB-STATION PART:- 33 KV VCB 1250A, 750MVA with Steel structure |
| 187 | Control panel I/C for 33 KV single T/F |
| 188 | Control panel I/C for 33 KV double T/F |
| 189 | 33 KV CT 400/200/1-1A |
| 190 | 33 KV CT 200/100/1-1A |
| 191 | 33 KV 1 Ph PT 33 KV/110 V |
| 192 | 11 KV SWITCH GEARS VCB:- (i) Incoming VCB 600/300/5A, 350MVA, I /C |
| 193 | (ii) Outgoing VCB 200/100/5A, 350MVA |
| 194 | (iii) Bus coupler 350 MVA |
| 195 | 11KV 3 Core XLPE Cable:- (i) 3 × 300 Sq.mm |
| 196 | (ii) 3 × 185 Sq.mm |
| 197 | 11/0.4 KV, 63 KVA Transformer. |
| 198 | 33 KV LINE PART:- PCC Pole 9.0 Mtr. Long |
| 199 | 11 Mtr. long S.T. Pole |
| 200 | 13 Mtr. long S.T. Pole |
| 201 | A.C.S.R. DOG CONDUCTOR |
| 202 | 33 KV 3x300 sqmm. XLPE Cable |
| 203 | 11 KV LINE PART:- 8.5 Mtr. long PCC Pole. |
| 204 | 11 Mtr. long S.T.P., SP-55 Pole. |
| 205 | 13 Mtr. long S.T.P., SP-72 Pole. |
| 206 | ACSR Raccon Conductor |
| 207 | 11 KV 3x185 sqmm. XLPE Cable Please Enable Macros to View BoQ information |
