|
| 1 | Cleaning jungle including up rooting of rank, vegetations grass, push, wood trees and samplings of grith upto 30cms. measured at a height of 1 M. above ground level and removal of rubbish up to a distance of 50M. Out side periphery of area cleared. (SOR-20/259(i)) |
| 2 | Construction of sub-grade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads. Transporting to site, spreading, grading to required slope and compacted to meet requirement of Table No 300-2: lead upto of 5.00KM (MORTH--20/305/3.18) |
| 3 | Granular sub-base with graded material, plant mix method Construction of granular sub-base by providing close graded material, mixing in a mechanical mix plant at OMC, carriage of mixed material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401. MORTH/4.01/401(A) |
| 4 | Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mix plant carriage of mixed material by tipper to site, laying in uniform layers with grader in sub-base/base course on well prepared surface and compacting with vibratory roller to achieve the desired density (MORTH/4.14/406(B)) |
| 5 | Brick edging in full brick width and half brick depth including excavation, refilling and disposal of surplus earth lead upto 50 metres. |
| 6 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (DSR-18/16.7.1) |
| 7 | Cement concrete with 4cm gaugeApproved stone ballast coarse sand & cement in the proportion of 8:4:1 including supply of all materials labour tools & Plants etc required for proper completion of the work |
| 8 | 8:4:1 (1 Cement 4: Coarse sand :8 graded stone aggregate 40mm nominal size) (SOR-20/281/5.08) |
| 9 | M-150 brick work in 1:6 cement & fine sand 1.25 FM mortar in foundation and plinth including supply of all material labour and T&P etc required for proper completion of the work. (SOR-20/303) same as item no 303 but in 1:4 one cement & four fine sand of 1.25 F.M. mortar. (SOR-20/305)Same as item no 305 but in 1:4 one cement & four coarse sand of 2.20 F.M. mortar. (SOR-20/305(A)) |
| 10 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). (DSR-18/16.69) |
| 11 | Providing and applying primer coat with SS1 grade bitumen VG-10 on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.75 kg/sqm using mechanical means. (MORTH 5.01/502) |
| 12 | Providing and applying tack coat with bitumen grade VG-10 using emulsion pressure distributor at the rate of 0.25 kg per Sqm on the prepared bituminous surface cleaned with mechnical broom. (MORTH-503(II)/502) |
| 13 | Providing and applying tack coat with bitumen grade VG-10 using emulsion pressure distributor at the rate of 0.25 kg per Sqm on the prepared bituminous surface cleaned with mechnical broom. (MORTH-503(II)/502) |
| 14 | Providing and laying dense graded bituminous macadam with Higher capacity batch type HMP using crushed aggregates of specified grading Premixed with bituminous binder VG-30 @4.5% by weight of total mix and filler, transporting the hot mix to work site, laying with hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve to desired compaction as per MORTH Specification CLAUSE No 505 complete in all respects (Morth/5.04/505(B)) |
| 15 | 50mm compacted thickness with bitumen perpetration of [email protected]% by weight of total mix. (MORTH-/5.05/505(B)) |
| 16 | Providing and laying bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder [email protected]% of mix and filler transporting the hot mix to work site laying with hydrostatic paver finsher with sensor control to the required grade, level and alignment rolling with smooth, wheeled, vibrator and tendom roller to achieve the desired compaction as per MORTH specification clause 507 complete in all respect (MORTH/507(B)/5.05) |
| 17 | 40mm compacted thickness with bitumen peretration of [email protected]% by weight of total mix |
| 18 | Providing and laying of hot applied thermoplastic compound 2.5mm thick including reflectorising glass beads @250gms per sqm area, thickness of 2.5mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes, Rates are inclusive of all taxes, royalty etc. all T&P/machine material and labour required for proper completion of work. (SOR-2020/New item/Sr.No.19.01) |
| 19 | Road Delineator. Providing and fixing of standard metal Delineator as per IRC 79-2019 consisting old minimum retro reflective unit exposed area of 330 square cm in while color, full cube corner micro prismatic non-metallic retro reflective shieling on each side conforming wilt IRC 67-2012 and meeting the coefficient of retro reflection values as per ASTMO 4956 Type XI table specification. The delineator shall be painted with powder coat of minimum 40 microns thickness, on top of which retro reflective sheeting shall be pasted on both side. The structure shall be manufactured in roll forming process and shall have height not less than B00mm above the ground, width not less than 100mm and shall extend nil more than 300mm below the ground while being installed. |
| 20 | The front and back faces of the delineator should be curved with a radius of not more than 200mm and with delta angle (or central angle of curve)lying between 20 degree and 30 degree, to increase the visibility of the delineator for vehicles moving in continuous curves. The delineator shall have grooves across the length to make the reflective sheets vandal-proof) The retro reflective sheeting shall be tested for 3 year outdoor weathering lest in Indian conditions as per IRC 67:2012 & proof of the same in form of government report shall be uploaded which quoting tender. If somehow tender pre qualification condition do not ask for government report then the report shall be submitted to Engineer-in-Charge before finalization of bill, The delineator is meant for application on gaps in median, traffic islands, dangerous bends, roundabouts, narrow bridges etc., or as desired by site engineer. CHAPTER-26 Traffic Sign S.No. 1 |
| 21 | Reflective Raised Pavement Markers (Road Studs/Cat Eye) Supply and fixing of reflective raised pavement marker with its body surface made of tough ASA (Acrylic styrene Acrylonitrile) or HIPS (Hi-impact Polystyrene) or aa acrylonitrile butadiene styrene (ABS). The marker shall supported a load of 1335 Kg tested in accordance with ASTMD 4280 and its reflective panels shall consist of number of lenses containing single or dual prismatic cubes of providing total internal reflection of the light entering the lens face. Retro reflecting surface shall preferably by 351 5 ̊ to base and area of each retro-reflecting surface shall not be less than 13.0Sacm road studs shall be legibly marked with name trade mark or other means of densification of the manufacture. Dimensions of road studs should not be less than 100mmX100mmX10mm. RPM (with shank) as per ASTM. Chapter-26 Traffic sign S.N.5 |
| 22 | Labour cess and GST will be paid extra as per Govt. orders. Please Enable Macros to View BoQ information |
