|
| 1 | Item Wise BoQ BoQ_Ver3.0 Item Wise Normal INR Only INR Select, Excess (+), Less (-) Tender Inviting Authority: Superintending Engineer, Electricity Construction & Work Circle-I, P.V.V.N.L., Meerut Bought Out Name of Work: Work for Increasing Capacity (1) 33/11 KV Substation BSR-1, Ghaziabad from 5+8 MVA to 2×10 MVA (2) 33/11 KV Substation PAC, Ghaziabad from 5+10 MVA to 2×10 MVA (3) 33/11 KV Substation Sector 6 New Vaishali from 5+5 MVA to 10+5 MVA) (4) 33/11 KV Substation Patel Nagar-II from 10+5 MVA to 2×10 MVA (5) 33/11 KV Substation Atore from 10+5 MVA to 2×10 MVA (6) 33/11 KV Substation Sector-62A New Khoda from 2×10 MVA to 3×10 MVA (7) 33/11 KV Substation Ahinsha Khand-2 , from 2×10+5 MVA to 3×10MVA Direct Tender Reference No : 13/ECWC-I/MRT/2026-27 Quote for Supply Portion only Bidder Name : Quote for Erection Portion only PRICE BID1. This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns after validating the sheet, else the bidder is liable to be rejected for this tender.2. Bidders are allowed to enter the Bidder Name and Unit Ex-Works Price and GST in %age only.3. All the material and erection practices shall be as per tender specification.5. Above Schedule Structure and quantities is provisional and may vary as per site requirement with due approval.6. Indicative scope of works and quantity of Items/Materials required for above work shall be as per the Price Bid. Any other material if required to complete the job and not mentioned above, shall have to be provided by the bidder without additional cost.7. Financial evaluation and selection of 'L1 Bidder' shall be done on the basis of total amount. The rates received in the tender will be final after the approval of the Competent Authority/Committee and the competent Authority/committee will have the right to negotiate in tender rate/amount.8. The work (i.e. shifting and erection/installation etc.) of new 10/20 MVA transformer(s) is under the scope of manufacturing/supplier firm as per the L.No. 2040/PVVNL-MT/MM/22-23, Dated 10.06.2022 of S.E. (MM-1), PVVNL, Meerut. The quoted rates by bidder for this item will be applicable only if this work is not carried out by the manufacturing/supplier firm for any reason.9. Tenderer must be fill-up the enclosed terms & conditions sheet and attached with 1st Part of Tender as well as scanned copy of same will be uploaded on NIC Website alongwith other documents.10. Bidders must be filled up the GST in %age, Otherwise it is assumed G.S.T. rates are included in the given ex-works price (Rs./Unit). NUMBER # TEXT # TEXT # NUMBER # TEXT # NUMBER NUMBER TEXT TEXT # NUMBER # TEXT# TEXT # NUMBER # NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER NUMBER TEXT TEXT NUMBER NUMBER NUMBER # NUMBER # TEXT TEXT NUMBER # NUMBER # DATE NUMBER # NUMBER # TEXT # Sl.No. Description of Works Item Code Tender Qty. Unit Estimated Rate Bought-out/Direct Specify Bought-out/Direct Addition / Deduction Addition / Deduction Values Currency Convertion against each Item Quoted Currency in INR / Other Currency Unit Ex-Works Price(Rs./unit) Excise Duty(Rs/Unit) CST/VAT(Rs/Unit) Other Taxes & Duties(Rs/Unit) Freight & Insurance Charges(in Rs./Unit) Unit FOR Dest. Supply Price incl. all Taxes and Duties(in Rs./Unit)(F+G+H+I+J) Total Value for Supply or Erection (In Rs.)(C x F) GST (in Rs.) in %age Total Value for GST (in Rs.) (F*M/100) Total Unit Price incl. GST (in Rs.) Total Amount excl. GST (in Rs.) (4×13) Total Amount incl. GST (in Rs.) (4×26) TOTAL AMOUNT In Words |
| 2 | Supply of following Material Neutral link L type Structurei) M.S.Channel (100x50x6)mm |
| 3 | ii) M.S.Angle (50x50x6)mm |
| 4 | Cable support Structurei) M.S.Channel (100x50x6)mm |
| 5 | ii) M.S.Angle (50x50x6)mm |
| 6 | Copper bus bar support T-type Structurei) M.S.Channel (100x50x6)mm |
| 7 | ii) M.S.Angle (50x50x6)mm |
| 8 | M.S.Structure for 33 KV Post Insulator with Plinth & Foundation as per specification in RESPO ( Channel-100*50*6mm) |
| 9 | M.S.Structure for 33 KV Lightening arrester with Plinth & Foundation as per specification in RESPO ( Channel-100*50*6mm) |
| 10 | 90 lbs rail pieces for T/F (44.64Kg/Mtrs.) |
| 11 | M.S.Round 32mm Dia for earthing. |
| 12 | Supply for Water level earthingi) G.I. pipe size 40 mm inner dia & thickness 2mm |
| 13 | ii) Solid copper cone Approx 225 mm long and 750 gm in weight |
| 14 | iii) Copper wire 6 SWG |
| 15 | iv) Copper flexible earthing strip of size 50x6mm for neutral |
| 16 | Ready mixed primer & ISI mark Aluminium Paint & ISI mark synthetic enaimel green paint for painting of installed all Structure & G.I.Strip. |
| 17 | M.S.Structure for 33 KV Line/Bus Isolator with Plinth & Foundation as per specification (01 No.)i) M.S.Channel (125x65x6)mm 3.5Mtr long for Vertical Structure. |
| 18 | ii) M.S.Angle (75x75x6)mm 2.6Mtr long for Horizental Structure. |
| 19 | iii) M.S.Angle (50x50x6)mm 0.81Mtr long for Bracing. |
| 20 | M.S.Structure for 33 KV Fuse set/ CT as per specification (01 No.)i) M.S.Channel (125x65x6)mm 3.5Mtr long for Vertical Structure. |
| 21 | ii) M.S.Angle (75x75x6)mm 2.8Mtr long for Horizental Structure. |
| 22 | Top Channel (G.I.100x50x2240mm long) |
| 23 | Dropper Channel (G.I.100x50x2028mm long) |
| 24 | G.I.Pipe 150mm Dia 2mm thick 2Mtr long |
| 25 | G.I.Pipe 150mm Dia 2mm thick 3Mtr long |
| 26 | Armoured Control Cable 2x2.5Sq.mm |
| 27 | Armoured Control Cable 4x2.5Sq.mm |
| 28 | PG Clamp |
| 29 | Copper bus bar of size (2400x50x6)mm |
| 30 | Carriage of following material from PVVNL Store 33KV Lightening arrester |
| 31 | 33KV Bus isolator 800A, |
| 32 | 33KV Post insulator |
| 33 | 33KV VCB 1250Amp. |
| 34 | 33KV CT 400/200/1-1-1A |
| 35 | 33KV Control Panel for double Transformer |
| 36 | 11KV VCB for I/C CTR 600/300/5A, 350MVA |
| 37 | 11KV Outgoing CTR 200/100/5A 350 MVA |
| 38 | 11KV XLPE cable 3x185mm² |
| 39 | 11KV XLPE cable 3x300mm² |
| 40 | 11KV Cable J/kit outdoor type for 3x300mm / 3x185mm |
| 41 | 11KV Cable J/kit indoor type for 3x300mm / 3x185mm |
| 42 | PCC Pole 11.0Mtr long. |
| 43 | Disc insulator Polymeric type 70KN |
| 44 | Disc fitting B&S type 70KN |
| 45 | 11KV composite Polymeric Pin insulator. |
| 46 | 11KV Fuse Set |
| 47 | 11KV TPMO |
| 48 | 11 KV Lightning arrestor |
| 49 | Cable H.T.XLPE 33KV 3x300SQ.M.M |
| 50 | Cable Box O/D 33KV 3x300 XLPE |
| 51 | 33KV Fuse set |
| 52 | ACSR Dog Conductor |
| 53 | G.I.Wire 6SWG |
| 54 | Erection of following Material & Miscellaneous Electrical Works.Removal of existing 5/8MVA Transformer and other accessories equipments.Disconnecting HT cable connection from 33KV side & 11KV side of 05/08MVA Power transformer for removing power transformer from plinth after proper shutdown. Dismantling of 11KV cable support structure, copper bus bar structure, M.S.Frame, Neutral structure, earthing strip etc. |
| 55 | Draining of transformer oil from conservator, radiators of existing 05/08 MVA T/F in to the dry & clean drum (Empty drums shall be provided by contractor) & Removal of conservator, radiators and other accessories from existing 5/8 MVA Power transformer |
| 56 | Safe Shifting of 05/08MVA Power transformer main body and other accessories from the substation switchyard to outside the switchyard at suitable place assigned by concern J.E/S.D.O (Distribution). |
| 57 | Re-assembling of conservator, radiators and other accessories to existing 05/08 MVA Power transformer & Re-filling the transformer oil (old & used in existing 5/8MVA T/F) |
| 58 | Erection of following Material & Miscellaneous Electrical Works.LINE/BUS ISOLATOR STRUCTURE: (i) Fabrication and erection of Isolator structure (Bus / Line) each by using 3.5 m long 04 Nos. of G.I.Channel of size (125×65×6)mm with bracing by G.I.Angle (50×50×6)mm size and 02 Nos. G.I.Angle (75×75×8)mm of size and 2.6m long on the top of Channel at both side of Isolator. The work also includes cutting, drilling, welding and proper alignment of the same for completion of work. |
| 59 | Excavation of earth-2x(1.10x0.60x1.0)x1 & Grouting of structure in C.C. ratio 1:3:6 in size 2x(1.10x0.60x1.00)x1 All civil material supply by the Contractor by fixing 02 no stone Pad. |
| 60 | Making plinth by C.C. ratio 1:3:6, in size 2x(1.10x0.60x0.30)x1 All civil material supply by the Contractor |
| 61 | 12mm thick plastering on plinth in ratio 1:4 of size- 4x(1.10x0.30)x1+4x(0.60x0.30)x1+2x(1.10x0.60)x1 All civil material supply by the Contractor |
| 62 | L.A.’s P.I.’s, C.T’s, and Fuse Set structure:-Febrication & Erection of Lightening Arrestors, Post Insulators/Fuse Set, C.T.’s, P.T's structure and Plinth for the same as per drawing No. RES-39 details:-Excavation of earth (0.30x0.30x1.0)m for 24 Nos. Pits of above structures. |
| 63 | Fabrication of L.A.’s, P.I.’s, C.T.’s, P.T and Fuse Set structure by using G.I. Channel (125x65x6) mm size and 3.5 m minimum height with 2 Nos. G.I. Angle (50x50x6)mm size on top of structure for installation L.A.’s, P.I.’s & Fuse Set. |
| 64 | C.C. work in ratio of 1:3:6 (cement, fine sand and brick ballast) of size (0.30×0.30×0.15)m for 24 Nos. pits for making bed for each structure. Work including proper ramming etc & C.C. work of ratio 1:3:6 (cement, coarse sand and 25 mm size stone grit) for the above plinths for structure of L.A.’s, P.I.’s, C.T.’s & Fuse Set 24 Nos. after ramming of earth of size (0.3x0.3x1.5)m. Over stone pad. |
| 65 | 12mm thick plaster with cement mortar ratio 1:4 (cement & fine sand) of plinth of 0.4m upper side. |
| 66 | Plinth for 10 MVA TransformerConstruction of plinth for 10 MVA, 33/11 KV Transformer of (3.46x3.46x1.0)m (0.50m below ground level and 0.5 m above ground level) as per details & drawing attached (All required matrials provided/Supply by the contractor own his cost):-Excavation of earth (3.7x4.7x0.75)m |
| 67 | Flooring of plinth in C.C. 1:4:8 (cement, sand & brick ballast) for making foundation bed. Size (3.7x4.7x0.15)m. |
| 68 | 1st Class brick work for side walls size 0.345 m wide upto 0.3m height and 0.23 m wide upto 0.35 m height cm C.C. ratio of 1:4 (cement & fine sand) |
| 69 | Filling of brick ballast in plinth in ratio 1:4:8 (cement, coarse sand & brick ballast) with proper ramming. Size (4.0x3.0x0.65)m. |
| 70 | R.C.C. work on the top of plinth in ratio 1:2:4 in (4.46x3.46)m size and 0.20m in thickness by using M.S.Tor of 12 mm dia. around 240Kgs making jal in two layers for reinforcement of plinth. The work also includes cutting, bending of M.S.Tor etc. Quantity of M.S.Tor of size 12 mm dia required for reinforcement of plinth in R.C.C. work for making jal in two layers. Work also includes cutting, bending and laying etc. in the T/F plinth. |
| 71 | Grouting of 02 Nos. 90/105 lb. Rail pieces of 3.46m long and (50x50x6)mm M.S.Angle in R.C.C. work at the top of plinth work and also for making groove along rail piece & confining the edges of plinth which includes cutting of rail and angles pieces etc. |
| 72 | 12mm thick plaster with cement mortar ratio 1:4 (cement & fine sand) of plinth of 0.5m upper side (Top & side walls). |
| 73 | Installation for 33/11KV 10MVA T/F Safe Shifting of 10MVA, 33/11 KV, Power transformer from out side of switchyard to near Power transformer plinth in Switchyard. |
| 74 | Erection & Installation of 10MVA Power transformer on Power Transformer plinth by fixing all accessories like radiators, conservator tank, filling the transformer oil to desired level and ensuring that there is no leakage, complete job in all respect. Reconnecting 2 Nos. earthing strip to transformer body. |
| 75 | Plinth for 33 KV V.C.B. (01 Nos.)Construction of plinth for the structure of 33 KV VCB & C.T.’s as per details for 03 No. (All required materials provided / Supply by the contractor own his cost) :-Excavation of earth of size (2.4x1.5x1.0)m pits for construction of plinth. |
| 76 | Brick Ballast ratio (1:3:6) (cement, sand & brick ballast) for foundation work (2.4x1.5x0.15)m plinth. All civil material provided by the Contractor on his own cost. |
| 77 | R.C.C. work in ratio 1:2:4 (cement, coarse sand & stone grit) of 20m size for making plinth of size (2.4x1.5x1.0)m and grouting of foundation bolts 04 Nos. for 33 KV VCB. All civil material provided by the Contractor on his own cost. |
| 78 | 12mm thick plaster with cement mortar in ratio 1:4 (cement & fine sand) of plinth. All civil material provided by the Contractor on his own cost. |
| 79 | Earthing of outdoor equipment, details as given below:-Cutting of 32mm.dia M.S. Bar-3Mtr.long and making one end in conical shape by forging process and driving it into the earth at each corner of bridge and Delta proper welding with M.S.Bars. |
| 80 | Digging of Pits & making of Bridge on L.A. & T/F neutral earthing by laying 32mm. dia M.S.Round. Electric welding on cross joints by providing “U” Clamp in size 25x6mm. of M.S.Flat and inter connecting both by M.S.Round 32mm.dia with over lap joint by providing M.S.Round-12mm dia, on both sides of over lap joints of M.S.Round, by electric welding. All joints shall be painted with black bituminious paint. |
| 81 | Digging of Trench of size-0.50x0.75x86M.,for laying of Earth mat throughout in switchyard and re-filling &ramming of the same earth in the to the trenches after completion of earth mat work. |
| 82 | Laying of 32mm.dia M.S.Bar in Trench, properly in alignment along the length and width in switchyard. |
| 83 | Cutting of 32mm.dia M.S.Bar-3M.long and making one end in conical shape, by forging process and driving it into the earth, in trench at fixed distance as per drawing and properly welding with M.S.Bar Earthmat. |
| 84 | Proper continuous electric welding of overlap joints of M.S.Bar upto a length of 150mm. On both sides,along the length of M.S.Bar and an extra piece of 12mm M.S.Round-150mm.long, providing on both sides of Overlap Joints and continuous electric welding on both side, along the length of M.S.Bar. All joints shall be painted with black bituminous paint. |
| 85 | Proper electric welding at X-joints of M.S.Bar and welding by providing 25x6mm.”U” type Clamp of M.S.Flat, and proper continuous electric welding with M.S.Electrode and M.S.Bar at each X-joints. All joints shall be painted with black bituminous paint. |
| 86 | Making earthing of all 11KV Switchgears, Control Panel and other equipments on both earth terminal inside the control room by providing G.I.Strip (10Mtr) in size 40x6mm. with 32mm. dia M.S.Round laid in trench with proper electric welding. |
| 87 | Providing & laying of G.I.Strip of size 50x6mm for connecting the earthmat with each equipment (Terminal Gantry, Bus Gantry, Bus Isolators, Line Isolator, 33KV C.T., 33KV V.C.B., L.As., Fuse Set, Post Insulators, T/F Body & its neutral and M.S.Frame of Cable Supporting Structure), various steel structures. The work also includes cutting, bendidng, straightening, over-laping and welding the earth strip with earth mat and by using high quality arc welding in already digged trenches. |
| 88 | Painting of Earth Strip of size (50x6) mm with one coat of ready mixed primer with two coats of ISI mark synthetic channel green paint. |
| 89 | Water level earthing by Boring and lowering of G.I.Pipe size 40mm dia of 2mm thickness, into the ground upto water level or minimum 50Mtr, which ever is more, with the lower end of solid copper cone Approx 224mm long and 750gm in weight shall be provided and screwed in pipe as well as bringing out a continuous 6SWG copper wire, from the cone upto the ground surface where it will be bolted to the G.I. Strip for Transformer neutral connection, the G.I.Strip will be connected to star point through providing Copper Bond Strip of size-50x6mm. |
| 90 | Construction of Control cable trench as per detailsExcavation of earth in size 0.650x0.40m. |
| 91 | C.C. work in foundation in ratio 1:3:6 (cement, sand & brick ballast) with proper ramming in size 0.65x0.15 mtr.) & First Class Brick work in cement mortar in ratio 1:4 in size 0.23x0.32 Mtr. Along with 25mm thick C.C. in floor of Cable Trench in ratio 1:2:4 (cement, coarse sand and stone ballast) 20mm gauge in size 0.3 mtr. Width. |
| 92 | Supply & Grouting of G.I. Strip of size 450x25x6mm in cable trench 100mm above floor level and at equal space distance 300mm. |
| 93 | Supply & Grouting of M.S.Angle Iron of size 50x50x6mm in upper edge of trench. |
| 94 | Plastering of Trench in Cement, Mortar in ratio 1:4, 12mm thick in cable trench. |
| 95 | Fabrication and fixing cable trench cover of M.S. Angle size 50x50x6mm of size 0.3m wide 1.0 mtr. Length with proper welding of 8 mm size of bar 2 Nos. in length and 6 Nos. in width including cost of CC casting & RCC in Ratio 1:2:4 (cement, coarse sand and stone ballast) (i) 1.0Mtr long . |
| 96 | Fabrication and erection of neutral earthing L Type support made of M.S.Channel size 100x50mm including supply of neutral bond. Structure shall be 4 Mtr. Long with 1 Mtr. Arms & 1.0Mtr M.S.Angle support from 50x50x6mm. Structure shall be grouted in ratio 1:3:6 in block size 300x300x700mm and painted of welding joint with one coat of Ready Mixed primer and Two coat of enamel Aluminium paint work includes connecting neutral bushing rod of power Transformer and G.I. Earthing strip with the help of flexible copper bond, G.I. Bolt and washer. |
| 97 | Fabrication and erection of cable support made of two pieces of M.S.Channel (100x50x6)mm, 4.0 meter long, joined to each other by means of 5 Nos. M.S.Angle (50x6) mm pieces of size 750 mm long each by welding at equal intervals and grouting in a block of size (300x300x700)mm in C.C. 1:3:6 (cement, coarse sand and stone ballast) complete and painted of welding joint with one coat of Ready Mixed primer and Two coat of enamel Aluminium paint. Work includes providing of three Nos. G.I. clamps made of (50x6)mm G.I. Flat for holding the cable including nuts and bolts. |
| 98 | Fixing 150mm dia 2mm thick 2M long G.I.Pipe over 33KV/11KV XLPE Cable before mounting the 2No. Cable on double pole / Cable support structure. The work includes fixing of Clamp, sealing of top and bottom end of the G.I.Pipe. One end of G.I.Pipe is to be buried under earth about 500mm. |
| 99 | Fabrication and grouting of G.I. Frames 3.60 mt. long for support of copper Bus Bar. Bus Bar will be provided in L.V. side of Power transformer. The M.S.frame shall be made of M.S.Channel (100x50)mm in ‘T’ shape. Providing 2 Nos. support of M.S.Angle iron (50x50x6)mm, 0.60mt. long below the top channel, drilling of 3 Nos. hole on the top channel for fixing of 11 KV pin insulator and painted of welding joint with one coat of Ready Mixed primer and Two coat of enamel Aluminium paint and grouting the frame in C.C. ratio 1:3:6 (cement, coarse sand and stone ballast) in a block of size (300x300x700) mm. The work also includes the fixing of 3 Nos. 11 KV pin insulator with pin and binding the copper Bus Bar with the pin insulator by Aluminium binding wire in complete. |
| 100 | Fabrication of copper bus bar of size (2500x50x6)mm in L.V. side of 5MVA/10MVA 33/11 KV, power transformer, Work includes connection of outside bus bar in L.V. side busing rod of Power Transformer and other side with outdoor 11 KV cable box as well as providing empire tape and H.T. tape etc. for proper insulation work. |
| 101 | Installation of 11 KV Switchgears in Control Room Carefully & safely shifting of 11 KV switchgear panels from outside to inside the switch gear room grouting foundation of bolts in C.C. ratio of 1:2:4 (including cutting of RCC floor and finishing of RCC floor) as per requirement placing, aligning and fixing of 11 KV anchor GI bolts and nuts of proper size for completion of work in all respect. |
| 102 | Proper fixing and making bus bar connection in between two switch gears after proper cleaning. Work also include proper insulation, taping by empire, PVC and H.T. tape etc. |
| 103 | Earthing of 11 KV Switch Gears:Earthing of 11KV switchgears by means of G.I. earth strips (50x6) mm connecting to 4 Nos. earthing electrodes of 32 mm dia. (including fabrications of earthing electrodes) 3m long on either side (as per RESPO drg. RES-40). welding of G.I.Earth strips (50x6)mm and also laying of the G.I.Round 32mm dia in trench of control room and connecting to sides squares including cost of G.I. earth strip (50x6)mm and earthing of all indoor equipment by laying and providing G.I.earth strip (50x6)mm including cutting & welding etc. |
| 104 | H.T. Power Cable Laying:Laying 11 KV, (3x300) mm2 XLPE, Cable from power transformer to 11 KV incoming switch gear in the cable trench 0.50 m wide, 0.90m depth. Providing 150 mm local sand for cushion beneath and 150 mm above the cable (quality of local sand required 0.375 cum/m in length). The cable shall be dully protected by brick. On both side of cable by laying brick vertically and bricks would also be laid bricks along the single cable (minimum 18 Nos. of bricks are to be laid top and outer side along the single cable. The work includes digging of trenches, laying of cable in under ground trenches, joining of terminal’s, back filling of earth and testing and commissioning of power cable etc. Spare cable shall be left over and laid in the trenches in shape of 6 m ring at both ends. |
| 105 | Laying and dressing of 11 KV 3x300 mm2 power cable in air/Trench. |
| 106 | Laying 11 KV, 3x185mm2 XLPE, Power cable from outgoing switch gear to 11 KV double poles in the cable trench 0.50m wide, 0.90m depth. Providing 150 thickness mm local sand for cushion beneath and 150mm above the cable (quantity of local sand required 0.375 cubm/m in length). The cable shall be duly protected by brick. On both side of cable by laying bricks vertically and bricks would also be laid horizontally on top of vertically laid bricks along the single cable (minimum 18 Nos. of bricks are to be laid top and outer side along the single cable. The work includes digging of trenches, laying of cable in under ground trenches, joining of terminal’s, back filling of earth and testing and commissioning of power cables etc. Spare cable shall be left over and laid in the trenches in shape of 6m rings at both ends. At the end of feeder cables, where the cable is to be laid across pucca/main road, 100 mm dia G.I. pipe will be weared over the cable in the cable trench for the protection of cable. |
| 107 | Laying and Dressing of 11KV 3x185mm² Power Cable in Air. |
| 108 | Preparation of 11 KV Power Cable ends:Making of 11 KV XLPE Heat shrinkable outdoor jointing kits 3x185Sq.mm/3x300Sq.mm after duly plumbing and taping of cable, providing, fixing and crimping of proper size good quality lugs |
| 109 | Making of 11 KV XLPE heat shrinkable indoor jointing kits 3x185Sq.mm/3x300Sq.mm in switch gears after carefully removing the insulation of cable, providing and crimping of proper size of lugs, plumbing and taping of cable with good quality available insulation tape with J/Kit boxes, Fixing and insulating of lugs on cable with switch gear complete in all respect. |
| 110 | Laying of different size of 2x2.5mm2 Armoured copper control cables i.e. from Buchholz realy to Marshalling box Marshalling box to indication protection board in switch gear room, 33 KV CT’s to CT’s Junction Box, 33 KV CT, 33 KV PT, V.C.B. Control Panel Junction Box to 33 KV VCB control panel and control panel to 33 KV VCB outdoor operating mechanism panel from T/F etc. in the cable trench including making proper connection at Buchholz Relay, Marshalling box and indication board as per required for installed equipment. |
| 111 | Laying of different size of 4x2.5mm2 Armoured copper control cables i.e. from Buchholz realy to Marshalling box Marshalling box to indication protection board in switch gear room, 33 KV CT’s to CT’s Junction Box, 33 KV CT, 33 KV PT, V.C.B. Control Panel Junction Box to 33 KV VCB control panel and control panel to 33 KV VCB outdoor operating mechanism panel from T/F etc. in the cable trench including making proper connection at Buchholz Relay, Marshalling box and indication board as per required for installed equipment. |
| 112 | Construction of 11 KV Feeder Double Poles:Erection and grouting of 2 Nos. PCC Pole 11.0Mtr long for making DP Structure including fabrication fixing of M.S.Channel, M.S.Angle, TPMO, Fuse Set, disc, insulators, pin insulators No. Plate, Danger board, barbed Wire (02 Kg per Pole), Stone Pad etc. the work includes supply and fixing of necessary clamps size 75x10mm with G.I.Nuts bolt & washer, bolts and washers. The work also includes grouting of Double pole support in C.C. 1:3:6 (cement, Core sand & stone ballast) in block of size (0.45m x 0.45 x 1/6 length of the pole) including earthing of Double pole with G.I. earthing rod complete in all respect. |
| 113 | Wearing of 110 mm dia 3 m long G.I pipe in the feeder cable of size of (3x185/3x300)mm2 XLPE 11KV power cable before making the outdoor cable boxes. The work includes the sealing of G.I.Pipe, top end and lower end of the pipe is to be buried in to the ground about ½ m and proper dressing of cable etc. The work includes lifting, mounting and clamping of 11 KV feeder cable boxes on the feeder with double pole structure and making connections including supply of cable mounting clamps etc. |
| 114 | Painting of StructuresPainting of the following structure with one coat of ready mixed primer and two coats of ISI Mark Aluminium paint after rubbing with sand paper to the surface of the structure including labour and T&P complete in all respect.Painting of Substation Structures |
| 115 | Installation of 33 KV Isolators:Assembling and installation of line/Bus Isolator on the isolator structure. Adjusting of operating mechanism in proper alignment so as to ensure smooth operation of the same. In case of Line Isolator proper operation of earth links shall also be ensured. The work includes fabrication for proper fixing if required. |
| 116 | Installation of 33 KV Lightning Arrestors: Assembling and installation/mounting of 3 Nos. lighting arrestors on the L.A.’s structure/terminal gentry, complete with earthing and line connections. The work includes fabrication for proper fixing, if required. |
| 117 | Installation of 33 KV Fuse Set:Assembling and installation of fuse set on the fuse set structure. The work includes fabrication for proper fixing, if required. |
| 118 | Installation of 33 KV Post Insulators:Installation of 3 Nos. PI on structure. The work includes fabrication for proper fixing, if required. |
| 119 | Installation of 33 KV VCBAssembling and installation of 33 KV VCB on the VCB out door structure on the plinth. Adjustment of operating mechanism in proper alignment for smooth operation of the same. The work also includes fabrication of addition arrangement for proper fixing, if required. |
| 120 | Installation of 33 KV VCB Control Panel for Double T/F Control Panel/ 33 KV VCB Control Panel Single T/F .Carefully and safely shifting of 33 KV VCB control panel from outside of the switch gear room to inside of the switch gear room, grouting with anchor bolts in the floor, work also includes cutting & proper finishing of floor if necessary for completion of work. Placing and fixing of panel on foundation, bolts of proper size in proper position and alignment. |
| 121 | Installation of 33 KV C.T.’s:Installation of 3 Nos. C.T.’s on the C.T’s structure. The work includes fabrication for proper fixing, and also clamps for C.T Connection if required to complete the work. |
| 122 | 33 KV CT’s Junction Box:Providing & fixing of junction box of size (400x400x150) mm made of G.I. sheet of 16 SWG in between 33 KV CT’s & control panel. The work also include making proper connection on the junction box and making all connection in between CT’s and control panel complete as per manufacture’s panel drawing including testing and commissioning of work etc. complete the work. |
| 123 | 33 KV Bus Bar Jumpering:Jumpering, including clamping/binding with ACSR Panther conductor/33KV 3x300mm2 XLPE cable with providing P.G.Clamp & other accessories.33 KV Bus Bar to 33 KV P.I |
| 124 | 33 KV Post insulator to Bus isolator. |
| 125 | 33KV Bus isolator to 33KV VCB |
| 126 | 33KV VCB to 33KV CT |
| 127 | 33KV C.T to 33KV Fuse set. |
| 128 | 33KV Fuse set to LA |
| 129 | 33KV LA to 33/11KV 5/10MVA T/F |
| 130 | Testing & Commissioning (To provide required No. of technicians to work on power T/f, HT/LT panels & 33KV line during testing as assisting technical hands of test team during commissioning & energisation). |
| 131 | Construction of SSO’s approached road 1.2 Mt wide in switch yard by laying dry brick ballast in 15 cm layer, 115 mm thick brick work 1:4 in both side of edge, providing 10 cm thick CC in ratio 1:2:4. The work include proper plastering top & side of road and making groove, leveling & dressing of earth beneath the brick work on edge. All required materials provived / supply by the contractor own his cost. |
| 132 | Construction of fire protection wall size 5Mtrx4.5Mtr above ground level (as per approved Drawing). Providing required Civil Material by the Contractor. |
| 133 | Hiring of D/G Set including carriage, loading, unloading & operating charges (With fuel) at 33/11KV Substation under construction in case L.T. Supply is not available near S/s within prescribed accessible limit.63KVA, Three phase, D/G Set for fabrication of different structure at Substation. |
| 134 | Disconnecting & Reconnecting of Fencing Boundary |
| 135 | Installation of PG Clamp |
| 136 | Chemical Pipe Earthing |
| 137 | Laying of 33KV, 3x300Sq.mm XLPE Cable in the Pucca trench / air on cable Riser Double Pole, existing cable trench, |
| 138 | Making of 33KV Outdoor type cable end termination by heat shrinkable XLPE Cable Jointing Kits and crimping with proper size aluminium lugs. Work includes providing Aluminum lugs, insulating tapes etc as per specifications. |
| 139 | Received Back Materila from site to any PVVNL Store Total in Figures 0.0 0.0 4.0 Construction of chamber for 100mm sluice plates item5 10.0 Nos Quoted Rate in Figures Select % 0.0 0.0 Zero Only Quoted Rate in Words Zero Only Please Enable Macros to View BoQ information |
