|
| 1 | SITC of new Automatic Lift ( as per manufacturer design & as per detailed specification below conforming to relevant IS ) and putting into operation after final testing in the existing lift shaft complete with all accessories and repairing the damage wall / floor if any etc to complete as reqd. Before installation of new Lift, the existing old Lift installation is to be dismantled and kept in safe/proper place as per direction of E.I.C/Authority |
| 2 | Make : Lift manufacturers approved under category-I (as per Memorandum of PWD/Govt. of W.B vide memo no. 75-W(C)/1M-20/15 dt. 03/03/2015) |
| 3 | Type: Passanger Lift . |
| 4 | Load : 15 Passenger / 1020 Kg |
| 5 | Control: Microprocessor based with AC variable voltage & variable frequency ( VVVF) |
| 6 | Machine:- Energy efficient machine, Gearless, without Machine Room |
| 7 | Position of Machine Room: MRL |
| 8 | Speed: 1.75 Mtrs./ Sec |
| 9 | Floor served: G +10 |
| 10 | Landing: 11, all on same side |
| 11 | Total Rise : 34 Mtr(approx.) [subject to actual site verification] |
| 12 | Operation: Microprocessor based simplex full collective with or without attendant. |
| 13 | Signals: Digital car position indicator,car travels direction indicator in car & at all landing with call registration indicator.COP & LOP must have stainless steel face plate silver brushed with surface mounted button.Button : All buttons on car & landing shall be luminous, on/off switch for Lift, fan, light, toggle switch or key switch for automatic/attendent mode of operation. Display type :Colour LCD / Segmented LCD/LED.Operation Push Button for lift maintenance & service should be on top of the car. |
| 14 | Leveling accuracy:± 5 mm(Micro levelling arrangement ) |
| 15 | Car inside : 1600mm wide x 1500mm deep x 2200 mm height and & depth suitable for 15-Passenger Lift as per relvant NBC code or OEM standard. |
| 16 | Car Entrance:Clear Opening:- 1000 mm (W) x 2000 mm (H ) protected with car door or as per OEM standard. |
| 17 | Car Finish & Enclosure: Stainless Steel sheet (20 SWG) with Hairline finish with hand rail. |
| 18 | a) Rear Mid Panel ---- Stainless Steel sheet (20 SWG) with Hairline finish (#4) |
| 19 | b) Rare corner Panel--- Stainless Steel sheet (20 SWG) with Hairline finish (#4) |
| 20 | c) Side Mid Panel--- Stainless Steel sheet (20 SWG) with Hairline finish (#4) |
| 21 | d) Side corner Panel--- Stainless Steel sheet (20 SWG) with Hairline finish (#4) |
| 22 | e) Front Panel--- Stainless Steel sheet (20 SWG) with Hairline finish (#4) |
| 23 | Car Ceiling & Lighting: Stainless Steel with hairline finish (#4) with LED lighting and Fan |
| 24 | Car Ventilation: Cross flow Pressure fan with anodised aluminium grill. |
| 25 | Car Flooring : Decorative granite flooring (As per direcion of EIC and according to this Department's Order). |
| 26 | Car Door: Stainless Steel centre opening automatic door provided with V3F controlled door drive system with 2D infrared curtain of light and mechanical force limiting device,with fire rating of minimum 120 minutes. |
| 27 | Landing Door: Stainless steel centre opening automatic door provided with V3F controlled door drive system, with fire rating of minimum 120 minutes. |
| 28 | Door Opening: Automatic power oprated door with full length Photocell assembly light curtain sensor |
| 29 | PROTECTIVE DEVICES & OTHER ACESSORIES |
| 30 | ARD: Automatic rescue device complete with dry maintenance free batteries as required.for automatic evacuation to the nearest floor in case of power failure / single phasing/others. |
| 31 | Overload Protection:Fully loaded with overload protection.On overloading the lift car will not start with door remaining open and give audio display indication |
| 32 | Emergency lighting in car: Battery operated emergency lighting in the lift car. |
| 33 | Intercom system: Battery operated intercom system in Lift Car, Machine Room & Control Room |
| 34 | Emergency Alarm: Battery operated alarm bell system in lift car and control room |
| 35 | Fireman switch: Fireman switch at main landing terminal. |
| 36 | Voice Synthesizer: Voice announcement system (Voice Synthesizer) in the car to announce the position of the elevator in the hoist way as the car passes or stops at a floor served by the elevator. |
| 37 | Main rope - As per manufacturer's standard conforming to respective applicable IS |
| 38 | Hand Rail:-Stainless Steel Mirror Finish Handrails on rear car panels |
| 39 | Auto fan cut-off |
| 40 | DIMENSION OF SHAFT & POWER SUPPLY |
| 41 | Available Shaft Dimension: 2567 mm width X 1958 mm or as per actual site condition [the Bidder should visit the site] |
| 42 | Available Pit Depth :1600 mm or as per actual site condition [the Bidder should visit the site] |
| 43 | Available Overhead : 5100 mm or as per actual site condition [the Bidder should visit the site] |
| 44 | Electric power supply: AC 415 Volt 3phase, 50 Hz, terminated in machine room as per IS |
| 45 | N.B. Rates should be quoted with minor civil works, wall cutting and mending good the damages to the original finish. |
| 46 | Less(-) Cost for dismantled unserviceable materials (incl. D.C. Motor) . Please Enable Macros to View BoQ information |
