|
| 1 | Excavation in trenches laying of cables, poles and stay and type of hard/dence soil not exceeding 1.5 Mtr wide and not exceeding 1.5 Mtr deep and getting out. |
| 2 | Returning, filling in including spreading, leveling and well ramming in layers not exceeding 25 cm as in soil. |
| 3 | Removing excavated soil of any type not exc 50 m and depositing where directed at a level n. exc 1.5 m above the starting point. |
| 4 | Supply, installation, testing and commissioning of manufacture's factory assembled and tested electric driven vertical openwell submersible pump set of capacity 20 HP capable of delivering minimum 120 LPM and maximum 840 LPM at 147 meter head , 2900 RPM, 3 phase, 415V, 50Hz ,install in SMC panel tank vertically with all compete accosories complete all as specified and directed. |
| 5 | S & F in repair Fully automatic star delta starter in sheet steel enclosure for 20 HP motor of relay range 13 - 25 Amp, complete all as specified and as per the directions of Engineer-in-charge. |
| 6 | M& L of UPVC Schedue 80 pipe of size 80 mm including all fittings complete all as specified and directed by engr-in-charge. |
| 7 | Supply & Fix PVC insulated & PVC sheathed industrial copper cable for submersible pump motors, flat three core of nominal area of conductor 10 sqmm,1100 Volts, conforming to IS: 694 complete all as specified and directed. |
| 8 | M& L of UPVC high pressure Ball valve of size 80 mm including all fittings complete all as specified and directed by engr-in-charge. |
| 9 | M& L of UPVC high pressure Non return valve of size 80 mm including all fittings complete all as specified and directed by engr-in-charge. |
| 10 | Supply and lay Double walled corrugated pipe (DWC ), heavy duty 77/63 mm bore for cable protection as a guard pipe including required accessories etc. complete as specified and directed. |
| 11 | Supply and laying under ground LT Cable XLPE insulated heavy duty armoured sheathed 1100 volts grade of cross sectional area 25 Sq mm, 4 core, with aluminium conductor, ISI marked as per IS : 7098( Part-1) along with suitable size aluminium cable lugs, gland if required and jointed in any description complete all as specified and directed by Engr-in-charge. |
| 12 | M & L for earthing complete with GI earth plate 60cm x 60cm x 6mm thick buried directly in ground/ earth pit not less than 2.25M below ground level with top edge of the plate not less than 1.5M below ground level connected to 32x6mm GI Strip by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electric plate No.5 of MES SSR Part I connected to earthing test point, testing complete including necessary earth pit PCC 1: 3: 6 chamber with CI cover refilling of soil etc complete all as directed by Engineer-in-Charge. |
| 13 | Supplying and laying heavy duty high pressure spring loaded Automatic pop up sprinklers (part/full circle)32/40mm BSP male threaded connection,operating pressure 3.0 to 5.0 bar discharge capacity of 87.5 litre per minute radius of coverage 25 meters Nozzle 0 to 360 degree adjustable,complete with brass swing arm and nozzle assembly ,install on riser pipe with all accesories and PCC work complete install in each sprinkler as per directed of Emgr-in-charge. |
| 14 | Supply & fixing of sintex SMC panel tank capacity 50000Ltr square type, made out of HOT PRESS MOULDED SHEET MOULDING COMPOUND panels of size 1005mm x 1005mm x 75mm (flange), 1005mm x 2010mm x 75mm (flange) and 1005mm x 502mm x (flange) the flange should be perpendicular to the main surface. The shape should be Trunked type for extra strength and 90 degree flanges pre drilled for bolting. All the Flanges of the 1 mt Panel should have 13 Nos. holes per side for fastening/joining the panels to one another. Hot Pressed Moulded SMC Pre Drilled Corner Pieces with built-in ribs of the size 75mm x 75mm should be provided for 90 degree joints of tanks wall to roof joints complete with olive green nuts, bolts and washers. Special sealent having excellent UV Resistance as well as suitable for portable water, complete with top covered construction having man hole with cover dia 600mm and internal FRP Ladder. CONTD TO 14.01 |
| 15 | The SMC Panel must be ISI marked meeteing BIS 14399(part 1 & 2). Tank inlet and outlet size 80mm dia and including RCC foundation wok completed all as directed of Engr-in-charge. Please Enable Macros to View BoQ information |
