|
| 1 | Dismantling/removal of existing water proofing membrane of any description and removal of material out of MOD land/sites etc complete all as specified and directed. |
| 2 | M&L 30mm average thickness PCC 1:2:4 type B0 using 12.5mm graded aggregate as in padding and (roof levelling course) on roof surfaces complete all as specified and directed. Note- Water proofing compound to be used @ 3% by weight of cement content for concrete padding work. |
| 3 | M&L for rendering in CM (1:3) 10mm thick over RCC roof, chajja/ brick wall mixed with water proofing compound @ 3% by weight of cement finished even and fair without using extra cement complete all as specified and directed. . Note - WPC shall be measured and paid separately. |
| 4 | Supply only liquid water proofing compound complete all as specified and directed. |
| 5 | M&L for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sqm including cleaning surfaces, complete all as specified and directed. . |
| 6 | M&L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and directed. |
| 7 | Demolition Cement Concrete (un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level) and removing debris, etc. to Outside MD/AF Land, complete all as specified and as directed. |
| 8 | M&L Cement Concrete 1:4:8 (40mm Graded Stone Aggregate) 100mm thick in Sub-bases, complete all as specified and as directed. |
| 9 | M&L Cement Concrete 1:2:4 (20mm Graded Stone Aggregate) 100mm thick as in flooring , complete all as specified and as directed. |
| 10 | M&L for Cement concrete type B-1, 1:2:4 (20mm graded aggregate) 40mm thick as in paths/Hardstanding finishing cement concrete surfaces even and smooth without using extra cement, complete all as specified and as directed. |
| 11 | M&L Cement Concrete 1:3:6 (40mm Graded Stone Aggregate) 75mm thick in plinth protection finishing cement concrete surfaces even and fair, complete all as specified and as directed. |
| 12 | M&L for Chequered cement concrete tiles 30 cm x 30 cm x 25 mm thick , set , jointed and pointed in neat cement slurry over and including 15 mm thick screed bed or bedding layers in CM 1:6 for laying floor finishes in floors , path / hard standing etc with grey cement and pigment (Coloured Tiles) complete all as specified and directed. |
| 13 | Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc, complete all as specified and as directed. |
| 14 | M&L for laying pre-polished 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath parks, lawn drive ways or light traffic parkings etc of required sterngth, thickness & sizeocompaction by using plate vibrator, filling the joints with sand and cutting of paer blocks as per required size and pattern, finishin and sweeping extra sand, including taking out existing odl pace rblokks and removing from site complete all as specified and as directed. |
| 15 | M&L sand filling under floors or in foundation incl watering and consolidation complete all as specified and directed. |
| 16 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed. |
| 17 | Taking down Cement Plaster including raking out Joints, hacking for Key, scrubbing down with Water and removing Debris, etc. to Outside MD/AF Land, complete all as specified and as directed. |
| 18 | M&L Rendering (External) 15mm thick in Cement Mortar 1:4 on Brick Walls/Concrete Surfaces mixing with WPC as per Manufactures instruction, plastered surfaces finished Even and Smooth without using Extra Cement, complete all as specified and as directed.NOTE : WPC shall be Measured and Paid for as ‘Supply only’ separately under appropriate Item. |
| 19 | M&L for rendering 10mm thick plaster in CM 1:6 on fair faces of brick work or concrete surfaces of walls finished even & smooth with out using extra cement complete all as specified and as directed. |
| 20 | M & L for 10 mm thick cement plaster in CM 1:3 as in ceiling finished even and smooth without using extra cement complete all as specified and directed. |
| 21 | Supply only Integral Water Proofing Compound, conforming to IS and/or as approved, complete all as specified and directed. |
| 22 | Material & Labour for preparing new Plastered Surfaces of Walls and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Camouflage pattern) with silicon additives @ 1.43 litre/ 10 sqm, over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed. |
| 23 | M&L for preparing new surfaces of wall and applying two coats of cement base paint over a coat of chalk whitening complete all as specified and as diected. |
| 24 | M&L for preparing of old surfaces of walls and applying one coat of cement based paint complete all as specified and directed. |
| 25 | M&L for preparing of new surfaces of walls and applying two coats of distemper oil emulsion over 1mm wall care putty complete all as specified and directed. |
| 26 | M&L for preparation of old wood surfaces of any description, not otherwise descri-bed, over 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed. |
| 27 | M&L for preparation of old painted steel and iron surfaces of any description over 10cm width or girth not otherwise described and applying one coats of synthetic enamel paint complete all as specified and directed. |
| 28 | M&L for preparing of old surfaces of wall/chequered tiles floor and applying one coat of Apex ultima weather proof emulsion paint complete all as specified and directed. |
| 29 | M & L preparing old surface of ceiling and applying one coat of distemper oil emulsion over and including one coat of putty complete all as specified and directed. |
| 30 | M&L for preparing of old surfaces of walls incl complete removal of existing treatment and applying two coats of distemper oil emulsion over 1mm wall care putty complete all as specified and directed. |
| 31 | M&L for preparing of old surfaces of walls and applying two coats of distemper oil emulsion complete all as specified and directed. |
| 32 | M&L for preparing of old surfaces of walls and applying one coat of distemper oil emulsion complete all as specified and directed. |
| 33 | M&L for preparation of old surfaces of wall and applying one coat of white wash complete all as specified and directed. |
| 34 | M&L for preparation of old surfaces of ceiling and applying one coat of white wash complete all as specified and directed. |
| 35 | M & L preparing new surface of ceiling and applying two coat of oil emulsion distemper over a coat of chalk whiting complete all as specified and directed. |
| 36 | M&L for preparation of new surface of ceiling and applying three coat of white wash complete all as specified and as directed. |
| 37 | Demolition Brick work built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc., complete all as specified and as directed. |
| 38 | M&L Brick Work with Sub-Class ‘B’ Bricks (Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and as directed. |
| 39 | M&L Brick work with Sub-Class ‘B’ Bricks but except Bricks (Serviceable Bricks obtained from Item here-in-before) including removing old Mortar, Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and as directed. |
| 40 | Dismantling of Asbestos cement/Translucent (corrugated, semicorrugated, plain, etc.) sheets in roof/wall coverings, complete all as specified and as directed. |
| 41 | S&F for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 42 | S&F for Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 43 | Dismantling structural steel or Mild steel work of any discription not otherwise provided for, complete all as specified and directed. |
| 44 | S&F for Steel work in tubular/angular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240, complete all as specified and directed. |
| 45 | M&L preparing New or previously untreated Steel and Iron Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a Red Oxide Zinc Chrome Primer, complete all as specified and as directed. |
| 46 | Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets, complete all as specified and as directed. |
| 47 | Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles With Semi perforated 12mm thick micro tegular edged GRG false ceiling tilesof Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS8225:1987, Noncombustible as per BS 4 76 (part 4 )-1970 and light reflectance of4 76 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of s1ze 600x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1 OOOmm length and Lshape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in- Charge. |
| 48 | Providing and fixing Gypsum Board 605x605x 12mm thick in ceiling fixed with screw as per manufacturer's instructions, complete all as specified and directed. |
| 49 | S&F GI Powder Coated Snap Grid Frame Work of size 600x600mm for False Ceiling with Supported and Hanging of Mild Steel Rod of ‘J’ Bolt including Provision for ceiling Board 12mm thick in Ceiling, fixed on Snap Grid, complete all as specified and as directed.Note: Ceiling board will measured and paid seprately under appropriate item. |
| 50 | M&L hangers 6 mm dia. G.I. (upto 1200mm length) (size of grid 605x605mm ) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed. |
| 51 | S&F in repairs Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at to wall complete all as specified and directed. |
| 52 | S&F in repair 5 mm thick PVC sheet fillets of width 35 mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and drawing complete all as specified and directed. |
| 53 | Dismantling Floor, Paver Tiles, Hearth or Wall Tiling, etc. including Cement Mortar Bedding (but not backing) and removing debris, etc. to Outside MD/AF Land, complete all as specified and as directed. |
| 54 | M&L Non-skid Glazed Ceramic Coloured/Printed Tiles 400x400x6.0 to 7.0mm thick in Flooring, set and jointed in Neat Cement Slurry and pointed in White/Coloured Cement, laid over and including 15mm thick Screed or Screed Bed in Cement Mortar 1:4, complete all as specified and as directed.NOTE : Cost of Cement Screed Bed shall deem to be include in the Quoted Unit Rate. |
| 55 | M&L Coloured Glazed Ceramic coloured Tiles in vertical surface 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the Tiles, complete all as specified and as directed. |
| 56 | Providng and laying Vitirified Coloured Tiles 9 to 10mm thick (Square/ Rectangular), Double Charge, Light shade, Polished, area of each Tile not exc. 0.36 Square Metre in Floors, etc with 3mm spacers, set and Jointed in Neat Cement Slurry, laid over and including 15mm thick Screed or Screed Bed in Cement Mortar 1:4, including grouting of joints, complete all as specified and as directed. NOTE : (a) Cost of Cement Screed Bed shall deem to be include in the Quoted Unit Rate.(b) Payment of grouting of joints to be made separately under appropriate items. |
| 57 | M&L Vtirified Coloured Tiles 9 to 10mm thick (Square/ Rectangular) Double Charge, Light shade, Polished, area of each Tile not exc. 0.36 Square Metre in Vertical Surface i.e. Dado, Skirting,etc., set and jointed in Neat Cement Slurry and pointed in White or Colour Cement to match the Tiles, complete all as specified and as directed. |
| 58 | M&L for Rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:4 to receive tiles etc on vertical surfaces of walls complete all as specified and directed. |
| 59 | M&L Machine Cut Kota Stone Slab 20-25mm thick in Flooring over and including Cement Screed 15mm thick in Cement Mortar 1:6, laid and jointed with Grey Cement Slurry mixed with Pigment to match the Shade of the Slab including Rubbing and Polishing, complete all as specified and as directed. |
| 60 | Demolition of cement concrete (reinforced) in ground floors and pavings n.exc 15cm thick, including removing rubbish off the premises complete all as specified and directed. |
| 61 | M & L for RCC 1:2:4 (type B1) using 20mm graded aggregate as counter/platform supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. |
| 62 | M & L for Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or complete all as specified and directed. |
| 63 | M & L for 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like including screed bed 15mm thick in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. |
| 64 | M&L Providing edge moulding to 18-20mm thick Granite stone any description of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and directed. |
| 65 | Dismantling water tanks exc 250 but n.exc 500 Litres capacity complete all as specified and directed. |
| 66 | Dismantling water tanks exc 500 but n.exc 1000 Litres capacity.1000 Litres capacity complete all as specified and directed. |
| 67 | S&F Rotational moulded polye thylene water storage tanks of 500 ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed. |
| 68 | S&F Rotational moulded polye thylene water storage tanks of 1000 ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed. |
| 69 | S&F 25 mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 20mm-210gms./ 25mm-455gms/ 40mm- 690 gms) complete all as specified and as directed. |
| 70 | S&F in repair 25 mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 20mm-210gms./ 25mm-455gms/ 40mm- 690 gms) complete all as specified and as directed. |
| 71 | Disconnecting existing tanks exc 250 and n. exc 500 ltr , setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc complete all as specified and directed. Note :- Bleeching powder to be spread in the bottom of tank before fixing / installing in position. |
| 72 | Disconnecting existing tanks exc 500 and n. exc 1000 ltr setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc complete all as specified and directed. Note :- Bleeching powder to be spread in the bottom of tank before fixing / installing in position. |
| 73 | Disconnecting existing tanks exc 1000 and n. exc 2000 ltr (including UG sumps) , setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc complete all as specified and directed. Note :- Bleeching powder to be spread in the bottom of tank before fixing / installing in position. |
| 74 | S&F in repair Looking Mirror 5.0mm thick of size 600x600mm, fixed with Chromium Plated Brass Spacers 25mm to 30mm in size (One Each Corner) including rounding the edges of the Mirror and Fixed-in-repairs, complete all as specified and as directed. |
| 75 | S&F in repair Brass Chromium Plated Tubular Towel Rail 20mm dia ‘D’ type 60 Cm long with Brackets and Fixed-in-repairs, complete all as specified and as directed. |
| 76 | S&F in repair stainless steel Grating Round 100mm dia with waste hole jointing with Solvent Cement and Fixed-in-repairs, complete all as specified and as directed. |
| 77 | S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed. |
| 78 | S & F in repair Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and as directed. |
| 79 | S & F in repair brass chromium plated Urinal spreader for fixing with 15 mm dia pipe complete all as specified and as directed. |
| 80 | S & F in repair 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed. |
| 81 | S & F in repair 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed. |
| 82 | S & F in repair PVC (SWR) bends any 75mm bore complete all as specified and as directed |
| 83 | S & F in repair PVC (SWR) bends any 110mm bore complete all as specified and as directed |
| 84 | S&F in repair 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. |
| 85 | S&F in repair 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed. |
| 86 | S&F in repair Stack clamps for 100 mm dia pipes , out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed. |
| 87 | S&F in repair PVC (SWR) bends any radius 110mm dia complete all as specified and directed. |
| 88 | S&F in repair PVC (SWR) branch piece, single (single Y) equal or unequal 75mm dia complete all as specified and directed. |
| 89 | S&F in repair PVC (SWR) branch piece, single (single Y) equal or unequal 110mm dia complete all as specified and directed. |
| 90 | S&F in repair PVC (SWR) gully trap 125/110mm setting and jointing with solvent cement and making good of disturbing gound with PCC 1:2:4 complete all as specified and directed. |
| 91 | S&F in repair Stainless steel sink with drainage board made out of 1 mm thick sheet of overall size 915x460mm with bowl size 410x330 x160mm with plugs washers, CP waste coupling and 40mm dia GI light grade waste pipe upto chamber fixed on and including cantilever angle iron 25x25x6mm (2 Nos) brackets complete including making good the disturbed surface using PCC 1:2:4 type B-I using 20 mm graded stone aggregate complete all as specified and directed. |
| 92 | S & F in repair 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed. |
| 93 | Taking up or down Steel/UPVC water tubing 15mm bore (dia) and Connections, segregating the Serviceable Pipes and Connections, stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and as directed. |
| 94 | Taking up or down Steel/UPVC water tubing 20mm bore (dia) and Connections, segregating the Serviceable Pipes and Connections, stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and as directed. |
| 95 | S&F 15 mm bore Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and directed. |
| 96 | S&F 20 mm bore Unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., any type of pipe complete all as specified and directed. |
| 97 | Refixing Old Steel Tubing 15mm bore (dia) and Connections (Serviceable Pipes and Connections obtained from Item No 95 here-in-before) in new or old position (Walls, Ceiling, Floors, etc.) including cleaning both inner and outer surfaces of Pipes by using Wire Brush including provision of new GI Connections (as required ordered at Sites), complete all as specified and as directed. |
| 98 | Refixing Old Steel Tubing 20mm bore (dia) and Connections (Serviceable Pipes and Connections obtained from Item No. 96 here-in-before) in new or old position (Walls, Ceiling, Floors, etc.) including cleaning both inner and outer surfaces of Pipes by using Wire Brush including provision of new GI Connections (as required ordered at Sites), complete all as specified and as directed. |
| 99 | S&F 16 mm Brass elbow for PVC/ iron pipe complete all as specified and directed. |
| 100 | S&F 20 mm Brass elbow for PVC/ iron pipe complete all as specified and directed. |
| 101 | S&F 16 mm Brass Tee for PVC/ iron pipe complete all as specified and directed. |
| 102 | S&F 20 mm Brass Tee for PVC/ iron pipe complete all as specified and directed. |
| 103 | S&F 20 mm Brass union for PVC/ iron pipe complete all as specified and directed. |
| 104 | S&F in repairs Gun-metal, globe or gate valves 20 mm bore, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 105 | S&F in repairs Gun-metal, globe or gate valves 25mm bore, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 106 | S & F in repair vitreous china wash down water closet pan (pedestal pattern ) p or s type (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed. |
| 107 | S&F Vitreous China White Squatting Pan of size 580x440mm, Orissa Pattern with Integral Foot Rests, ‘P’ or ‘S’ Trap, providing Joints between Flush Pipe and Socket of WC Pan, Cones, India Rubber (nozzles of WC Pan) incluiding provision of Lime Concrete Bedding and Making Good to Floor/distrubed surfaces and Fixed-in-repairs, complete all as specified and as directed. |
| 108 | S&F in repair ceramic floor mounted, one piece water closet (wesern toilet), white (including seat cover, inlet and outlet rubber gasket, 'S' trap of size 67cmx36cmx75cm including fixing complete as per manufacturer instruction complete all as specified and as directed by Engr-in-charge. |
| 109 | S & F in repair PVC Flushing Cistern 10 Litre capacity White, Low Level, Valve less, Syphonic action type with Inlet, Ball Valve, Float and Handle, PVC Waste Pipe 32mm bore (dia) of suitable Length, a pair of Cast Iron Bracket/ Erecting Stand duly painted including cutting and pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 and Fixed-in-repairs, complete all as specified and as directed. |
| 110 | S&F in repair Vitreous China wash basin, white, flat back, size 550x400mm excluding taps,waste, chain and plug and porcelain stopper but including brackets cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and as directed. |
| 111 | S&F in repair plastic water closet seat cover, white or black colour closed pattern with flat bottom including taking down old seat cover complete all as specified and as directed. |
| 112 | S&F in repair Bib Tap 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type, Long Body with Capstan Head, screwed down, screwed for Iron Pipe or for Brass Ferrule, complete all as specified and as directed. |
| 113 | S & F in rapair Pillar taps, cast copper alloy, with capstan heads, chromium plated, facny type screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed. |
| 114 | S&F in repair Stop Cock 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type with long Shank and Cup (Concealed type), screwed down, high pressure, with Crutch or Butter-fly Handle, screwed Both Ends for Iron Pipe or for Unions and Fixed-in-repairs, complete all as specified and as directed. |
| 115 | S&F in repair Angle Valve 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type, screwed down, high pressure, screwed both Ends for Iron Pipe and Fixed-in-repairs, complete all as specified and as directed. |
| 116 | S&F in repairs Swan neck pillar cock, brass chromium plated for wash basin 360 degree moving spout fixed to 15mm bore pipe complete all as specified and as directed. |
| 117 | S&F in repairs 15 mm CP Bib cock 2 way with wall flange and single knobs complete with all fittings complete all as specified and as directed. |
| 118 | S&F in repair PVC Waste Pipe 32mm dia (bore) having 600mm long and fixed complete to Walls, Ceilings or in Floors, etc.and Fixed-in-repairs, complete all as specified and as directed. |
| 119 | S&F in repair PVC Connection Pipe 15mm size and 60 Cm in length with Adopter Nuts of PVC and Fixed-in-repairs, complete all as specified and as directed. |
| 120 | S & F in repair Soap dish SS, fixed to plugs with chromium plated brass screws complete all as specified and directed. |
| 121 | S & F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and as directed. |
| 122 | S&F in repair Brass CP wall mixer with telephonic shower for mixing hot & cold water screwed down for iron pipe and fixed to 15mm bore pipe complete all as specified and as directed. |
| 123 | S&F in repair CP Overhead rain shower - ABS type Square 180x180mm complete with all fittings complete all as specified and as directed. |
| 124 | Taking down Wooden Chowkat or Frame with Shutter (without taking off Shutter from the Frame), n.exc. 1.5 Square Metre Each, complete all as specified and as directed. |
| 125 | Taking down Wooden Chowkat or Frame with Shutter (without taking off Shutter from the Frame), exc. 1.5 Square Metre but not exc. 4.0 Square metre each, complete all as specified and as directed. |
| 126 | Taking down and refixing of Shutters of any description in same opening n exc 1 sq.m each complete all as specified and as directed. |
| 127 | Taking down Shutters of any description n exc 1sq. m each complete all as specified and as directed. |
| 128 | Taking down Shutters of any description exc 1Sqm, n exc 2sq. m each complete all as specified and as directed. |
| 129 | S&F factory made single extruded WPC (wood polymer Composite) solid door/window/ceosetory windows & other frames/chowkhat of size 50x110mm comprising of virgin PVC polymer of K value 58-60 (suspension grade), calcium carbonet and natural fibre (wood powder/rick husk wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed screw SS crews having minimum frame density of 750kg/Cum, screw withdrawl strength of 2200N (Face) & 1100 N (Edge), minimum compressive strength of 58N/mm2, modules of elasticity 900N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in postion with MS hold fast/lugs /SS dash fasterners of required dia and length complete as per direction of Engineer-in-Charge. (MS hold fast/lugsof SS dash fastenrers shall be paid for seprartely). |
| 130 | Providing and fixing factory made single extruded WPC (wood polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K valure 58-60 (Suspension grade), calcium carbonate and natural fibre (wood powder/rice husk/wheat husk) and non toxic additives (mximum toxicity index of 12 for 100gms) having minimum density of 650kg/cum and screw withdrawl strength of 1800N (Face) & 900 N (Edge), minimum compressive strength of 50N/mm2, modules of elasticity 850N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be lamindated with PVC foil of minimum 14 micron thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, complete all as per direction of Engnieer-in-Charge. |
| 131 | S&F powder coated aluminium frame for partitions,doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed. |
| 132 | S&F Anodised aluminium powder coated of any colour (Thickness or powder coating not less than 50 micron) door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed. |
| 133 | S&F aluminium powder coated (Three track) sliding windows with frame of size 92x31.75x1.50mm and shutters of size 42 x 18x 1.50 mm with rubber gasket, beading and locking arrangement including making good to the disturbed portion complete and stainless steel wire mesh 0.36 mm nominal dia of wire with 1.40 mm average width of aperture and fixed with stainless steel wire staples and fixing 5 mm thick glass with necessary rubber beading, gasket etc complete all as specified and as directed by Engr-in-charge. Note - Glazing/ wire mesh shall be included in the unit rate. |
| 134 | S&F aluminium windows ( Double track) / ventilator powder coated of section 85.00mm x 31.75 mm x 1.50 mm thick shutter of section 19 x 40 x 1.5 mm with rubber gasket beading and locking arrangement etc completeand stainless steel wire mesh 0.36 mm nominal dia of wire with 1.40 mm average width of aperture and fixed with stainless steel wire staples and fixing 5 mm thick glass with necessary rubber beading, gasket etc complete all as specified and as directed by Engr-in-Charge . Note - Glazing/ wire mesh shall be included in the unit rate. |
| 135 | S&F aluminium powder coated grill 6 mm thick fixed to walls with and including 'H' of 'F' aluminium channel of size 38 mm x 12 mm x 1.50 mm complete all as specified and directed. |
| 136 | S&F Sheet Glass 4.0mm thick, Ordinary quality and glazing with Oil Putty in Square exc. 0.50 Sqm in Each Pane of Windows, complete all as specified and as directed. |
| 137 | M&L for 12mm thick Particle board, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work complete all as specified and as directed. |
| 138 | S&F 2nd class hard wood plain solid strength chowkats frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joint complete all as specified and directed. |
| 139 | S&F 30mm thick flush door shutter, solid core construction with block board core and both face is covered with decorative face veneer with lipping/frame to match complete all as specified and as directed. |
| 140 | M&L for 35mm thick second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed. |
| 141 | S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC Sheet rainforced with MS square tube complete all as specified and directed. |
| 142 | S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed. |
| 143 | S&F Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified and directed. |
| 144 | S & F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed with MS screw & bolts in repairs complete all as specified and directed. |
| 145 | S & F in repair stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm fixed with MS screw & bolts in repairs complete all as specified and as directed. |
| 146 | S&F Aluminium Handle 150mm long (weight not less than 120 Gram), Extruded Section, Fabricated type, anodised, complete all as specified and as directed. |
| 147 | S&F Aluminium Barrel Tower Bolt 200mm long (weight not less than 210 Gram), Extruded Section, complete all as specified and as directed. |
| 148 | S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specifed and as directed. |
| 149 | S & F 100mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed. |
| 150 | S&F 100mm size Butt hinges, heavy weight, cold rolled mild steel, and fixed complete all as specified and directed. |
| 151 | S & F in repair floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor 140mm length. complete all as specified and directed. |
| 152 | S&F in repair aluminum alloy, anodized, sliding door bolt of length 250mm with hasp & staple (bolt type) & fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy complete all as specified and directed. |
| 153 | S&F in repair 150mm size aluminum handles, cast type anodised complete all as specified and directed. |
| 154 | S&F in repair aluminum anodized barrel tower bolt of extruded section, length of bolt 150mm complete all as specified and directed. |
| 155 | S&F in repair 100mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and directed. |
| 156 | S&F in repair Butt hinges 100mm, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed. |
| 157 | Hacking out old broken Glass (any thickness, size, quality or description) from Wooden or Metal Frames, glazed with putty or fixed with beads, complete all as specified and as directed. |
| 158 | S&F Sheet Glass 4.0mm thick, Ordinary quality and glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane of Steel Windows, complete all as specified and as directed. |
| 159 | S&F in repair for mild steel, chromium plated Curtain Rod 25mm dia (as approved) , complete all as specified and as directed. |
| 160 | S&F in repair for mild steel, chromium plated Side Dome and to be fitted/tightened for Curtain Rod 25mm dia with Screws, complete all as specified and as directed. |
| 161 | S&F in repair for mild steel, chromium plated Bracket (Shaped), for holding for mild steel, chromium plated Curtain Rod 25mm dia , complete all as specified and as directed. |
| 162 | S&F in repair Door Closer Aluminium (Die cast) body, hydraulically regulated, Designation No. 3, Universal type, suitable for Door Shutters of 851mm to 1000mm in width and of weight between 61.00 to 80.00 Kilogram , complete all as specified and as directed. |
| 163 | S & F mild steel 2 lever Mortice lock, vertical type, size 100 mm complete all as specified and directed. |
| 164 | S & F in repair mild steel 2 lever Mortice lock, vertical type, size 100 mm complete all as specified and directed. |
| 165 | S&F in repair Zebra roller Blinds (horizontal) alongwith necessary fitting and fixtures for window for light filtering, privacy, UV protection Corded rolled up curtain window of any shade complete all as specified and as directed by Engr-in-Charge |
| 166 | M&L ATT Along the external/internal wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed. |
| 167 | M&L Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed. |
| 168 | Repairs of rolling shutter door any size and incl taking down, refixing in same opening after alingment & greasing as required complete all as specified and directed. Please Enable Macros to View BoQ information |
