|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m All kinds of soil. |
| 2 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:3:6 (1 Cement : 3 coarse sand(zone III) : 6 graded stone aggregate 40 mm nominal size) |
| 3 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 4 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars |
| 5 | Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete . |
| 6 | Brick work with clay fly ash F.P.S. (non modular) brick of class designation 3.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand). |
| 7 | Brick work with clay fly ash F.P.S. (non modular) brick of class designation 3.5 in superstructure above plinth level up to floor one level in: Cement mortar 1:6 (1 cement : 6 coarse sand). |
| 8 | 12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand) |
| 9 | 6 mm cement plaster of mix 1:3 (1 cement : 3 fine sand) |
| 10 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 11 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :New work (two or more coats) over and including water |
| 12 | Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm |
| 13 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bar etc.including priming coat with approved steel primer all complete.Fixed to steel window by welding. |
| 14 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 15 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 16 | Providing and laying Vitrified tiles in floor in different sizes(thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet forplacing the tiles gently and easily. Size of Tile 600 x 1200 mm . |
| 17 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 18 | Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. Made of G.I. wire of dia 4 mm |
| 19 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 20 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer- in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 21 | Providing and fixing ACP in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With ACP panes of 4.0 mm thickness ( For DooR ) |
| 22 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections ……………...all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :Powder coated aluminium (minimum thickness of powdercoating 50 micron) |
| 23 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws. 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 24 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :125 mm |
| 25 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 300x16 mm. |
| 26 | Providing and fixing bright finished brass door latch with necessary screws etc. complete : 300x16x5 mm |
| 27 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 300x10 mm |
| 28 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work |
| 29 | Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid |
| 30 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 31 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively. |
| 32 | White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap |
| 33 | Providing and fixing brass bib cock of approved quality : 15 mm nominal bore |
| 34 | Providing and fixing brass stop cock of approved quality : 15 mm nominal bore |
| 35 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 25 mm nominal dia Pipes |
| 36 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 15 mm nominal dia Pipes |
| 37 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter |
| 38 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 75 mm diameter |
| 39 | Providing and fixing 100 mm sand cast Iron grating for gully trap. |
| 40 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore |
| 41 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 42 | Constructing soak pit 1.20x1.20x1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. |
| 43 | Providing and fixing uplasticised PVC connection pipe with brass unions : 30 cm length |
| 44 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 45 | Providing and fixing PVC false ceiling at all height including providing and fixing of frame work made of special sections, required angle cleats, flanges, dash fasteners, angle hangers of required length with nuts & bolts of required size and G.I. channels running at the spacing of 1200 mm centre to centre, G.I. wire at every junction, including fixing perimeter channels to wall/partition with the help of rawl plugs, dry wall screws including fixing of PVC Ceiling to ceiling section and perimeter channel with the help of dry wall screws including jointing and finishing to a flush finish of tapered and square edges of the board and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge with : 5 mm thick PVC Ceiling |
| 46 | Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, filling the joints with fine sand etc. allcomplete as per the direction of Engineer-incharge. |
| 47 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 48 | Carriage of materials by mechanical transport …... building rubbish. Lead 1Km |
| 49 | Providing and fixing 2 SEATER ARC SWING Specification Main structurePipe- structure made of MS Pipe OF 60 od and 25 od pipe OF 3 to 4 mm thickness Seats- structure made of Bucket seat and FRP pata OF 3 TO 4 mm Thickness. Paint – Powder Coated (Thickness 90 micron) The aforementioned item should be having a minimum of 01 years of warranaty and should be implemented all complete as per the direction of engineer in charge, |
| 50 | Providing and fixing Straight FRP Slide (8 Feet) Specification Main structurePipe- structure made of ms. Pipe OF 48 od, 32 od and 25 od pipe and box pipe are ½” x 2”pipe. Slide- structure made of FRP Paint – Powder Coated (Thickness 90 micron) The aforementioned item should be having a minimum of 01 years of warranaty and should be implemented all complete as per the direction of engineer in charge, |
| 51 | Providing and fixing WAVE Slide (8 Feet) Specification Main structurePipe- structure made of ms. Pipe OF 48 od, 32 od and 25 od pipe and box pipe are ½” x 2”pipe. Slide- structure made of FRP Paint – Powder Coated (Thickness 90 micron) The aforementioned item should be having a minimum of 01 years of warranaty and should be implemented all complete as per the direction of engineer in charge, |
| 52 | Providing and fixing DOUBLE SEE SAW/DOUBLE BAR FOUR SEATER SEE SAW Main structurePipe- structure made of M.S. Pipe OF 60 OD, 48od and 42od pipe OF 2 to 3 mm thickness Seats - structure made of LLDP Handrails - structure made of M.S. 1” Pipe Round Pipe. Paint – POWDER COATING The aforementioned item should be having a minimum of 01 years of warranaty and should be implemented all complete as per the direction of engineer in charge, |
| 53 | Providing and fixing DOME CLIMBER Main structureMain Pipe- structure made of M.S. Pipe OF 50 OD OF 2 TO 3 mm thickness Stairs- structure made of heavy duty M.S. Pipe of 32 OD of 2 to 3 mm thickness.Handrails - structure made of M.S. 1” Round Pipe. Paint – POWDER COATING. The aforementioned item should be having a minimum of 01 years of warranaty and should be implemented all complete as per the direction of engineer in charge, |
| 54 | Providing and fixing Rainbow Climer Main structure Main Pipe- structure made of M.S. Pipe OF 50 OD OF 2 TO 3 mm thicknessStairs- structure made of heavy duty M.S. Pipe of 32 OD of 2 to 3 mm thickness.Handrails - structure made of M.S. 1” Round Pipe.Paint – POWDER COATING . The aforementioned item should be having a minimum of 01 years of warranaty and should be implemented all complete as per the direction of engineer in charge, |
| 55 | Providing and fixing FABRO NET CLIMBER Main structureMain Pipe- structure made of M.S. Pipe OF 50 OD OF 2 TO 3 mm thickness Climbing Sheet- structure made of FRP(4 TO 5 MM THICKNESS) Rope – Made of Nylon of 16 mm Thickness Handrails - structure made of M.S. 1” Round Pipe. Paint – POWDER COATING. The aforementioned item should be having a minimum of 01 years of warranaty and should be implemented all complete as per the direction of engineer in charge, |
| 56 | Providing and fixing S CLIMBER Main structureMain Pipe- structure made of M.S. Pipe OF 50 OD OF 2 TO 3 mm thickness Stairs- structure made of heavy duty M.S. Pipe of 32 OD of 2 to 3 mm thickness. Handrails - structure made of M.S. 1” Round Pipe. Paint – POWDER COATING.The aforementioned item should be having a minimum of 01 years of warranaty and should be implemented all complete as per the direction of engineer in charge, |
| 57 | Providing and fixing S CLIMBER Main structureMain Pipe- structure made of M.S. Pipe OF 50 OD OF 2 TO 3 mm thickness Stairs- structure made of heavy duty M.S. Pipe of 32 OD of 2 to 3 mm thickness. Handrails - structure made of M.S. 1” Round Pipe. Paint – POWDER COATING.The aforementioned item should be having a minimum of 01 years of warranaty and should be implemented all complete as per the direction of engineer in charge, |
| 58 | Providing and fixing at site inclusive of all the charges of material transportation and placing/fixing, with premium finishing of equipments all complete as per the direction of engineer in charge Chest Press And Shoulder Press Specification Main structure- Pipe- structure made of GI Pipe OF 4” OD , 42 OD AND 32 OD OF 3 to 4 mm thickness Arm – structure made of GI Pipe 32 OD 4 mm thickness. Bearing Ball bearing (6205) Bearing Caps - Made up of HDPE Material. Seats structure made of M.S. SEAT OF 2 mm Thickness. Pole Caps Made up of HDPE Material. Paint Powder Coated (Thickness 90 micron). |
| 59 | Providing and fixing at site inclusive of all the charges of material transportation and placing/fixing, with premium finishing of equipments all complete as per the direction of engineer in charge Leg Extension Specification Main structure- Pipe structure made of GI Pipe OF 60od 42 OD AND 32 OD OF 3 to 4 mm thickness Bearing Ball bearing (6205) Bearing Caps Made up of HDPE Material. Seats- structure made of GI SHEET OF 2 mm Thickness. Pole Caps Made up of HDPE Material. Paint Powder Coated (Thickness 90 micron) |
| 60 | Providing and fixing at site inclusive of all the charges of material transportation and placing/fixing, with premium finishing of equipments all complete as per the direction of engineer in charge Leg Press Double Specification Main structure Pipe structure made of GI Pipe OF 4” OD and 42 OD OF 3 to 4 mm thickness Bearing Ball bearing (6205) Bearing Caps Made up of HDPE Material. Seats- structure made of M.S. SEAT OF 2 mm Thickness. Pole Caps Made up of HDPE Material. Paint Powder Coated (Thickness 90 micron). |
| 61 | Providing and fixing at site inclusive of all the charges of material transportation and placing/fixing, with premium finishing of equipments all complete as per the direction of engineer in charge Double Shoulder Wheel Specification Main structure Pipe structure made of GI Pipe OF 4” OD AND 32 OD OF 3 to 4 mm thickness Pole Caps Made up of HDPE Material. Paint Powder Coated (Thickness 90 micron). |
| 62 | Providing and fixing at site inclusive of all the charges of material transportation and placing/fixing, with premium finishing of equipments all complete as per the direction of engineer in charge Double Standing And Seating Twister Specification Main structure Pipe structure made of GI Pipe OF 4” OD, 42 OD AND 32 OD pipe OF 3 to 4 mm thickness Twister Plate structure made of M.S. SEAT OF 5 mm Thickness with LLDPE PLATE/SHEET. Seats- structure made of GI SHEET OF 2 mm Thickness. Pole Caps – Made up of HDPE Material. Paint Powder Coated (Thickness 90 micron) |
| 63 | Providing and fixing at site inclusive of all the charges of material transportation and placing/fixing, with premium finishing of equipments all complete as per the direction of engineer in charge PARALLEL BAR Specification Main structure Pipe structure made of GI Pipe OF 3” and 32 OD OF 3 to 4 mm thickness Paint Powder Coated (Thickness 90 micron). |
| 64 | Providing and fixing at site inclusive of all the charges of material transportation and placing/fixing, with premium finishing of equipments all complete as per the direction of engineer in charge Air Walker Double Specification Main structure Pipe structure made of GI Pipe OF 4” od and 42 OD OF 3 to 4 mm thickness Arm structure made of GI Pipe 32 OD 4 mm thickness. Bearing Ball bearing (6205) Foot Rest - structure made of GI SHEET OF 2 mm Thickness. Bearing Caps - Made up of HDPE Material. Pole Caps Made up of HDPE Material. Paint Powder Coated (Thickness 90 micron). |
| 65 | Providing and fixing at site inclusive of all the charges of material transportation and placing/fixing, with premium finishing of equipments all complete as per the direction of engineer in charge Double Surfboard Specification Main structure Pipe- structure made of GI Pipe OF 4” OD and 42 OD OF 3 to 4 mm thickness Arm structure made of GI Pipe 32 OD 4 mm thickness. Bearing Ball bearing (6205) Foot Rest structure made of GI SHEET OF 2 mm Thickness. Bearing Caps - Made up of HDPE Material. Pole Caps Made up of HDPE Material. Paint Powder Coated (Thickness 90 micron). |
| 66 | Levelling of ground by Tractor Mounted grader for making good surface including disposal of excess earth within a lead of 50 m etc. complete as per direction of Engg-in-charge |
| 67 | Total impact of GST for the purpose of CTC Please Enable Macros to View BoQ information |
