|
| 1 | Supply, Erection, Testing and commissioning of 9.0 mtr Long GI (65 micron DFT single dip) Octogonal poles uniformally tappered with thickness of 3mm with bottom/top Dia of 175 mm x 70mm & base plate of 275x275x16mm/pcd 250 mm provided with proper door opened gear box for connections on the bottom side with G.I. Foundation Bolts (J Type) M24x750 mm long (Set of 4 no.’s per pole) ,(standard make) including providing and fixing of suitable sign board, mentioning DOS, DOC, Estimated Cost,etc. |
| 2 | Supply, Erection, Testing and commissioning of 7.0 mtr Long GI (65 micron DFT single dip) Octogonal poles uniformally tappered with thickness of 3mm with bottom/top Dia of 135 mm x 70mm & base plate of 225x225x12mm/pcd 250 mm provided with proper door opened gear box for connections on the bottom side with G.I. Foundation Bolts (J Type) M25x750 mm long (Set of 4 no.’s per pole) ,(standard make) including providing and fixing of suitable sign board, mentioning DOS, DOC, Estimated Cost,etc. |
| 3 | Laying of RCC foundation for 9.0 mtr. Long Octagonal poles including proper curing. 0.6mX0.6mX1.2m (RCC with concrete ratio 1:1.5:3 with minimum 8 Nos. of 12 mm dia longitudinal MS reinforcement rods with rings of 8 mm dia not more than 200 mm C.C for fixing the pole). |
| 4 | Laying of RCC foundation for 7.0 mtr. Long Octagonal poles including proper curing. 0.55mX0.55mX0.8m (RCC with concrete ratio 1:1.5:3 with minimum 8 Nos. of 12 mm dia longitudinal MS reinforcement rods with rings of 8 mm dia not more than 200 mm C.C for fixing the pole). |
| 5 | Supplying and fixing of Earthing of Octagonal Pole Complete by GI Pipe 40 mm or GI Rod 20mm 3 mtr long through GI Strip (25x3)mm |
| 6 | Pre fabricated galvanized four way ring type top bracket (700 mm radius with 48.3 OD GI Pipe) to be fitted on top of octogonal pole for hodling lights. |
| 7 | Providing and fiixing of prefebricated galvanised single way top bracket(1000 mm long with 48.3 OD GI Pipe) to be fitted on top of octagonal pole for holding llighting luminaries |
| 8 | Providing and fixing of Cable Termination & Luminary connections using 4-way terminal block/ connectors & four no. of 1 amp MCB with strip (Legrand/Havells make or equivalent) including copper lugs, nuts& bolts,washers etc for poles with two way type bracket to be fitted properly inside the door opened gear box provided on the bottom side of the pole. (Complete Job) |
| 9 | Providing and fixing of Cable Termination & Luminary connections using terminal block/ connectors & one no. of 1 amp MCB with strip (Legrand/Havells make or equivalent) including copper lugs, nuts& bolts,washers etc for poles with two way type bracket to be fitted properly inside the door opened gear box provided on the bottom side of the pole. (Complete Job) |
| 10 | Supply ,installation ,testing and commissioning of outdoor type 100 watt LED Flood light(10000 lumens), IP66 of BAJAJ/GE/HPL/ HAVELLS/WIPRO/ PHILLIPS/ CROMPTON or any approved vendor by KPDCL make suitable for above high mast application complete with minimum (DLP) two years of onsite replacement warranty.This also includes Auto ON/OFF Day Night Sensor. |
| 11 | 3x1.5 sq.mm PVC insulated flexible copper wire for service connections from connection plate to the LED luminary individual circuit including loop & earthings laid properly including bunching (Havells/polycab/KEI/Anchor/Plaza make or equivalent) |
| 12 | 10 mm²Cable (2C) or higher size from LT Line to meter ,1.1k V Grade, Armoured, XLPE FRLS type to be carried through conduit/pipe underground (A/G only in case of site constrains). The cable shall include end termination lugs with its crimping /taping. (Havels/polycab or equivalent make) |
| 13 | Provinding and fixing of Miscellaneous items like Alumunium cable thimbles/lugs at termination points, insulation tape , binding wire, screws, etc as required for commissioning of the HM lights. |
| 14 | Providing and fixing of Surge Protector for the 100 Watt LED type lighting fixture complete. Please Enable Macros to View BoQ information |
