Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil. 0.00 LVL. TO 1.50 MTR. D.S.R.-2.6.1 |
| 2 | 1.50 LVL. TO 3.00 MTR. D.S.R.-2.6.1+2.26.1 |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth,sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. D.S.R.-2.25 |
| 4 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. D.S.R.-2.25a |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), D.S.R.-4.1.8 |
| 6 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. D.S.R.-2.27 |
| 7 | Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement:2 coarse sand) to match the existing floor. With Chlorpyriphos/ Linadane E.C. 20% with 1% concentration. D.S.R.-2.35.3.1 |
| 8 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.Concrete of M25 grade with minimum cement content of 330 kg /cum (For R.C.C. Lintel) For 362 kg/Cum. Ground Floor (Upto Plinth), D.S.R.-5.33.1.1 |
| 9 | Ground Floor (Above Plinth), D.S.R.-5.33.2.1 |
| 10 | First Floor, D.S.R.-5.33.2.1 |
| 11 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works above plinth level upto floor V level, Concrete of M25 grade with minimum cement content of 330 kg /cum. For 362 kg/Cum (Slab). Ground Floor, D.S.R.-5.33.2.1 |
| 12 | First Floor, D.S.R.-5.33.2.1 |
| 13 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works above plinth level upto floor V level, Concrete of M25 grade with minimum cement content of 330 kg /cum. For 362 kg/Cum [ (beam). Ground Floor (Upto Plinth), D.S.R.-5.33.1.1 |
| 14 | Ground Floor (Above Plinth), D.S.R.-5.33.2.1 |
| 15 | First Floor, D.S.R.-5.33.2.1 |
| 16 | All works up to plinth level, Concrete of M25 grade with minimum cement content of 330 kg /cum. For 362 kg/Cum [For M-25 ] (footing) D.S.R.-5.33.1.1 |
| 17 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works up to plinth level, Concrete of M25 grade with minimum cement content of 330 kg /cum. For 362 kg/Cum [For M-25 ] (column ). Ground Floor (upto plinth), D.S.R.-5.33.1.1 |
| 18 | Ground Floor (above plinth), D.S.R.-5.33.2.1 |
| 19 | First Floor, D.S.R.-5.33.2.1 |
| 20 | Add for using extra cement in the items of design mix over and above the specified cement content therein. D.S.R.-5.35 |
| 21 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand), D.S.R.-6.1.2 |
| 22 | Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size). D.S.R.-4.10 |
| 23 | Painting on D.P.C. with two coats of airblown bitumen 85/50 or 85/25 @ 1.7 kg/sqm approx. including cost of fuel if any. D.S.R.-4.13 |
| 24 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand), Ground Floor. D.S.R.-6.4.2 |
| 25 | First Floor. D.S.R.-6.4.2 |
| 26 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand), Ground Floor. D.S.R.-6.13.2 |
| 27 | First Floor. D.S.R.-6.13.2 |
| 28 | Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. D.S.R.-6.15 |
| 29 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Thermo-Mechanically Treated bars of grade Fe-500D or more. Ground Floor. D.S.R.-5.22.6 |
| 30 | First Floor. D.S.R.-5.22.6 |
| 31 | 15 mm cement plaster on rough side of single or half brick wall of mix : 1:4 (1 cement: 4 coarse sand). D.S.R.-13.5.1 |
| 32 | 15 mm cement plaster on rough side of single or half brick wall of mix:1:6 (1 cement: 6 coarse sand), Ground Floor. D.S.R.-13.5.2 |
| 33 | First Floor. D.S.R.-13.5.2 |
| 34 | 12 mm cement plaster of mix :1:6 (1 cement: 6 coarse sand), Ground Floor. D.S.R.-13.4.2 |
| 35 | First Floor. D.S.R.-13.4.2 |
| 36 | Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. Ground Floor. D.S.R.-5.30 |
| 37 | First Floor. D.S.R.-5.30 |
| 38 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. Polished Granite stone slab of all colour and texture except Black, Cherry/Ruby Red, Ground Floor. D.S.R.-11.56.2 |
| 39 | First Floor. D.S.R.-11.56.2 |
| 40 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red. Area of slab over 0.50 sqm, Ground Floor. D.S.R.-8.2.2.2 |
| 41 | First Floor. D.S.R.-8.2.2.2 |
| 42 | Providing edge double moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Granite work, Ground Floor. D.S.R.-.-8.3.2 |
| 43 | First Floor. D.S.R.-.-8.3.2 |
| 44 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. (Wash basin/ Kitchen sink ), D.S.R.-8.5 |
| 45 | Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set polymer modified quick set tile adhesive (water based) conforming to IS : 15477, ANSI: A 118.4 ET, EN12004/ISO 13007: C2TE in average 6 mm thickness, including grouting of joints Adhesive make: Laticrete 315 plus/Capa/kerakoll, in average 6 mm thickness, including grouting of joints Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-incharge Size of Tile 800x800 mm. Ground Floor. D.S.R.-11.49.3+11.48.3 |
| 46 | First Floor. D.S.R.-11.49.3+11.48.3 |
| 47 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by themanufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set polymer modified quick set tile adhesive (water based) conforming to IS : 15477, ANSI: A 118.4 ET, EN12004/ISO 13007: C2TE in average 6 mm thickness, including grouting of joints Adhesive make: Laticrete 315 plus/Capa/kerakoll, in average 6 mm thickness, including grouting of joints, Ground Floor. D.S.R.-11.47.3+11.43 |
| 48 | First Floor. D.S.R.-11.47.3+11.43 |
| 49 | Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set polymer modified quick set tile adhesive (water based) conforming to IS : 15477, ANSI: A 118.4 ET, EN12004/ISO 13007: C2TE in average 6 mm thickness, including grouting of joints Adhesive make: Laticrete 315 plus/Capa/kerakoll in average 6 mm thickness, including grouting of joints Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-incharge. Size of Tile 600x600 mm, Ground Floor. D.S.R.-11.49.2+11.48.4 |
| 50 | First Floor. D.S.R.-11.49.2+11.48.4 |
| 51 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of jointsFixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, ANSI: A 118.4 ET, EN12004/ISO 13007: C2TE in average 3 mm thickness, including grouting of joints Adhesive make: Laticrete 315 plus/Capa/kerakoll Size of Tile 600x600 mm, Ground Floor. D.S.R.-11.47.2+11.43 |
| 52 | First Floor. D.S.R.-11.47.2+11.43 |
| 53 | Supply & fixing of flexible non directional simpurity/crudlee range pvc sheet flooring in 2 mm thickness in the size of 2 mtr X 20 mtr use area classification 23/34/43 results from independent testing demonstrate that product inherently inhibits the growth of microbial strain MRSA. It shall be Group-T homogeneous in construction. The flooring shall be approx weight of 2.99 kg/m2,dimensional stability EN-434, static electrical charge <2kv, impact sound reduction approx ISO 717-2,Rsistnat to slip, fire ,chemical & does not favour in growth fungi & bacteria, diamond 10 coating for more durability ,easy to clean ,scratch protection ,high abrasion resistant, duly installed on smooth and hard surface with company recommended adhesive and seamless joint. Ground Floor |
| 54 | First Floor |
| 55 | Supply & fixing flexible Wallflex/walldesign PVC sheet wall cladding in 1 mm thickness in the size of 1.5 mtr X 20 mtr with polyurethane surface treatment testing results if inhibits the growth of MRSA in the wall with clean room certificatioin. Homogeneous vinyl wall covering (imported) with polyurethane shield .Classification EN-685 for wall only. Good resistant to chemical & fire ,anti fungi & bacterial growth, ,class A in clean room test and available in various colour shade duly installed on smooth wall with company recommended adhesive and seamless. Ground Floor |
| 56 | First Floor |
| 57 | Providing and applying a multi-layer, jointless self-leveling epoxy flooring system of specified total thickness (e.g., 3mm) over a cured concrete substrate. The process shall begin with rigorous surface preparation via mechanical shot-blasting or diamond grinding to remove laitance and achieve a CSP-3 surface profile for maximum mechanical bond. This is followed by the application of a high-penetration, solvent-free epoxy primer to seal the substrate pores. A build-up/screed coat of epoxy resin mixed with graded silica quartz shall be applied to achieve the required thickness and impact resistance, followed by a final topcoat of 100% solids, self-leveling epoxy resin in the approved color and finish. The resulting floor must be non-porous, chemical-resistant, and completely level, including all necessary materials, surface testing, and specialized application labor as per the technical data sheet of the approved manufacturer. Ground Floor |
| 58 | First Floor |
| 59 | Providing and applying a seamless epoxy mortar cove base to a specified height (e.g., 50mm to 100mm) at all wall-to-floor junctions. The process involves mechanical cleaning of the wall base and floor perimeter to ensure a solid bond, followed by the application of a dedicated epoxy primer. A specialized non-sagging epoxy mortar, consisting of a three-component resin and graded silica sand system, shall be hand-troweled using a radius coving tool to create a smooth, curved transition (typically 25mm to 50mm radius). Once cured, the coved area must be integrated into the main floor system by applying the same self-leveling epoxy topcoat to ensure a uniform, non-porous, and chemical-resistant finish that prevents bacteria or moisture ingress. The scope covers all materials, surface etching, masking for level top-lines, and finishing as per the manufacturer's hygiene standards. Ground Floor |
| 60 | First Floor |
| 61 | Providing & Fixing of Forbo Flotex color series flocked floor covering rolls having a density of 70 million fibres of nylon 6.6 per Sqm , Fire Test EN-13501, Appearance Retention Hexapod ISO 140-8, Friction Slip Resistance Test EN 14041 Class DS, sanitized anti-microbial treatment with resilient waterproof backing ,anti allergic certified by British allergy foundation, anti static, stain resistant, thickness 4.3 mm and approximate weight of 1.8 k.g./sqm of roll form with acoustic sound impact 17dB. Flotex to be installed over cement based smooth level hard flooring( Made in United Kingdom).. The carpet should be laid complete including company recommended adhesive. Ground Floor |
| 62 | First Floor |
| 63 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick, Ground Floor, D.S.R.-11.26.1 |
| 64 | First Floor D.S.R.-11.26.1 |
| 65 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. Ground Floor. D.S.R.-11.27 |
| 66 | First Floor D.S.R.-11.27 |
| 67 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Deduct for not using 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) bedding in laying of floor tiles and jointing with grey cement slurry @ 3.3 kg/ sqm. Fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quickset tile adhesive (Water based) conforming to IS: 15477, in average 3mm thickness. Glazed Vitrified tiles Matt/Antiskid finish of size. Size of Tile 600 x 600 mm. Ground Floor. DSR-11.41A-11.42+11.43 |
| 68 | First Floor. DSR-11.41A-11.42+11.43 |
| 69 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. Ground Floor. D.S.R.-8.31 |
| 70 | First Floor D.S.R.-8.31 |
| 71 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth, D.S.R.-4.17 |
| 72 | Providing & fixing ISI marked flush door shutters conforming IS: 2202 decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters (a) 30mm thick including ISI marked stainless steel butt hinges with necessary screws. Both side laminated. (i) Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. (Part I) 1.5 mm thick (ii)Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). (Total thickness of Door 30+1.5+1.50 mm = 3.30 mm) (DSR-9.21.2+9.23)+(DSR-9.127*2+9.26) |
| 73 | Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured): Rectangular or square, D.S.R.-9.24.1 |
| 74 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Frame size 65 x 100 mm, D.S.R.-26.86.5 |
| 75 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately). 35 mm thick, D.S.R.-26.88.2 |
| 76 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), D.S.R.-10.13.1 |
| 77 | Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Three track three panels sliding window with two glazed & one wire mesh panels with alluminium channel for roller track, wool pile, nylon rollers with s.s. 304 body. Using R2 series with foame (70mm & above)x(40 mm & above) & both glazed and fly screen sash (25 mm & above)x(50mm & above with zinc alloy (zamak) powder coated touch lock with hook (Height up to 1.20 meter). D.S.R.-9.147 A4.1 |
| 78 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). (a) Sal wood (DSR - 9.1.2) |
| 79 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4 mm thick, D.S.R.-10.30.1 |
| 80 | Painting with silicon & acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces :Two coats. Ground Floor. D.S.R.-13.51.2 |
| 81 | First Floor. D.S.R.-13.51.2 |
| 82 | Finishing walls with textured exterior paint of required shade :New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm (Asian Paint or equivalent), Ground Floor. D.S.R.-13.45.1 |
| 83 | First Floor. D.S.R.-13.45.1 |
| 84 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. Ground Floor. D.S.R.-13.80 |
| 85 | First Floor. D.S.R.-13.80 |
| 86 | Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete. D.S.R.-14.34 |
| 87 | Providing and fixing Stainless steel 304 grade sliding door bolts, of 16mmx250mm solid rod with required nuts, screws, keeper, etc. all item to s.s. 304 grade only and supplied along with material test certificate. (OZ-ALD-01(16x250mm) |
| 88 | Providing and fixing Stainless steel 304 grade tower bolts (barrel and plate type) with required nuts, screws, keeper, etc. all item to s.s. 304 grade only and supplied along with material test certificate. (a) 300 mm x 10mm -(OZ-TB-S-12\\" ) |
| 89 | (b) 250 mm x 10mm (OZ-TB-S-10\\" ) |
| 90 | Providing and fixing Stainless steel 304 grade handles with plate fixed with S.S. screws,etc. complete of size 10mm 125mm all item to s.s. 304 grade only and supplied along with material test certificate. (ODG-11-10x125) |
| 91 | Providing & fixing EN:1154 Certified 500000 cycle tested door closer made of Aluminium Diecasted body having UL stamping sutable for 80kg with double speed adjustment with necessary accessories and screws etc. Complete. (NSK-680) |
| 92 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm. D.S.R.-22.7.1 |
| 93 | Foam concrete filling |
| 94 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. D.S.R.-22.5 |
| 95 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. D.S.R.-10.28 |
| 96 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing:1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources), D.S.R.-4.2.3 |
| 97 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).Ordinary cement without any pigment, D.S.R.-11.20.4 |
| 98 | Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991, in true horizontal level suspended on interlocking metal powder coated T-Grid of hot dipped galvanised iron section of 0.40 mm thick on Silhouette profile,rotary stiched double webbed white with 6mm reveal profile (white/black),comprising of main-T runners of size 15x42mm of length 3000 mm, cross - T of size 15x42 mm of length 1200 mm and secondary intermediate cross- T of size 15x42 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 22x19x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. With 15 mm thick integral densified micro edge light weight calcium silicate false ceiling tiles, D.S.R.-26.23.1 |
| 99 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flangen of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks), D.S.R.-12.45.1 |
| 100 | Centering and shuttering including strutting, propping etc. and removal of form for:Foundations, footings, bases of columns, etc. for mass concrete, D.S.R.-5.9.1 |
| 101 | Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick, D.S.R.-5.9.20 |
| 102 | Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick, D.S.R.-5.9.21 |
| 103 | Columns, Pillars, Piers, Abutments, Posts and Struts, D.S.R.-5.9.6 |
| 104 | Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment. D.S.R.-25.1 |
| 105 | Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: (a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: (i) Coloured tinted float glass 6 mm thick substrate with reflective soft coating on face # 2, + 12 mm Airgap + 6 mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement. D.S.R.-25.2 |
| 106 | Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.26.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25-0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement. D.S.R.-25.3 |
| 107 | Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineerin- Charge. D.S.R.-25.4 |
| 108 | Providing, fixing, testing and commissioning of white vitreous china wall mounted type European water closet with C.P. bolts, nuts, C.I. chair (painted with two coats of enamel paint over a coat of primer) or other hanging arrangements, built-in concealed/exposed white vitreous china low volume compatiable dual flush cistern (Flowrate as 4/2 Lit per Flush) with C.P. bolts, nuts, supporting arrangements, bakelite / poly propylene seat & cover with C.P. hinges & rubber buffers, complete with all accessories. Including cutting & making good the walls & floors wherever required complete as per the satisfaction of the Engineer in charge. D.S.R.-17.2 |
| 109 | W.C. pan with ISI marked white solid plastic seat and lid, D.S.R.-17.2.1 |
| 110 | Providing and Fixing Handicap Toilet set including EWC, Cistern, Seat Cover, Fittings, Washbasin,, Hinged Rail, Grab Bar and Faucet with Spatula Lever including Cast Iron chair backed and necessary bolts and nuts complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required as per technical specifications, provided drawings by architect,techincal specification and as directed by the authority EIC. including Toilet Set(Jaquar - CNS-WHT-755SN)+ Cistern Set(CNS-WHT-207)+ Wash Basin(CNS-WHT-811) and Grab Bar(WAC-WHT-BG0800 & WAC-WHC-BR0600 ) as directed by EIC. |
| 111 | Supply, installation , testing & commissioning Health Faucet ABS with double lock 1.2 m long SS flexible hose and wall hook including CP flange. 15mm dia. |
| 112 | Providing and fixing first quality white vitreous china under counter/above counter washbasins, specially fabricated CI / MS brackets, painted with two or three coats of enamel paint of approved shade over a coat of primer, 32 mm CP brass waste fitting , bottle trap , pipe to wall with CP brass flange and rubber adopter for waste connection complete including filling gap between counter and wash basin with approved type poly sulphide sealant, cutting and making good the walls wherever required. White vitrious china wash basin. D.S.R.-17.7A |
| 113 | Supply, installation , testing & commissioning CP Brass sink mixer for kitchen sink with wall flange, extended operating lever, swinging spout and surgical purpose handle complete with all accessories as required and making good the walls wherever required. D.S.R.-17.11 |
| 114 | Supply, installation , testing & commissioning C.P. cast brass bottle trap for kitchen sink with extension piece, rubber adaptor, wall flange, union, C.P. brass chain rubber plug complete as required and as per approval from engineer-in-charge. D.S.R.-17.22 |
| 115 | Providing and fixing of C.P Toilet paper roll holder with all accessories as per approved specifications and making good the walls wherever required. D.S.R.-17.34 |
| 116 | Providing & Fixing of C.P. brass robe hook with all accessories as required and making good the walls wherever required. |
| 117 | Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. D.S.R.-17.80 |
| 118 | Providing and fixing CP 600mm long Brass towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour. D.S.R.-17.73 |
| 119 | Providing and fixing CP 600mm long glass Shelf complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour. D.S.R.-17.33 |
| 120 | Providing and fixing C.P. brass bib cock of approved quality. 15 mm nominal bore. D.S.R.-17.7A |
| 121 | Providing, fixing, testing and commissioning of C.P. brass angle valve with C.P. wall flange, Nut and Washer etc. complete as required. 15 mm nominal bore, D.S.R.-18.18.1 |
| 122 | Supply, installation , testing & commissioning of 15mm CP brass single lever concealed bath and shower wall mixer with divertor with 3 way shower head, spout, OH shower with adjustable type arm with wall flange with slip fit connection & hand shower with flexible pipe with bracket complete as required by the engineer in charge. D.S.R.-17.22B |
| 123 | Supply, installation , testing & commissioning of Soap Dispenser with all accessories as required and making good the walls wherever required. D.S.R.-17.71 |
| 124 | Providing and fixing solid state, no touch operting, fully hygienic hand drier of approved shade with single blower, with time delay, summer & winter control, music while drying, volume ON/OFF controls including providing necessary brackets, cable from drier to Plug, Plug top key and lock etc, complete as required. |
| 125 | Supply, installation , testing & commissioning of C.P Towel ring with all accessories as required and making good the walls wherever required. D.S.R.-17.73 |
| 126 | CHAPTER 2: INTERNAL DRAINAGESupply, installation, testing and commissioning of uPVC SWR Type-B pipes conforming to IS 13592 with fittings to IS 15328, ring-fit (RRJ) joints with EPDM rubber rings conforming to IS 5382, suitable for soil, waste and rainwater discharge. All pipes shall be fixed on surface / on wall using GI/MS band clamps with EPDM lining at required intervals, including making holes in walls/ceilings, sleeves, supports, anchor fasteners, cutting/chamfering, lubrication, alignment, leak testing, cleaning, painting/marking, and making good the surfaces complete in all respects. Internal Toilet (Soil & Waste Pipe). 75 mm |
| 127 | 110 mm, D.S.R.-12.42.1.2 |
| 128 | Exposed on Wall (Soil & Waste Pipe) 110 mm, D.S.R.-12.42.1.2 |
| 129 | 160 mm |
| 130 | Providing, Installing, testing and commisssioning UPVC Multi trap of self cleansing design with or without vent arm with provision for connecting upvc inlet fitttings complete including cost of cutting and making good the walls and floors where ever required complete in all respects with necessary arrangements with proper care at all levels, protecting fittings and floor trap till the final handing over etc as per technical specifications, provided drawings by architect and as directed by the authority EIC. (make:Astral,Ashirvad & supreme) |
| 131 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. |
| 132 | Bend without door (45°) 110mm |
| 133 | 160mm |
| 134 | Bend without door (87.5°) 110mm |
| 135 | 160mm |
| 136 | Y' Fitting without door. 110mm |
| 137 | 160mm |
| 138 | Clean Out Plug (COP). 110 mm, D.S.R.-12.42.1.2 |
| 139 | Reduced 'Y' Fitting without door 110mm x 75mm |
| 140 | 160mm x 110mm |
| 141 | Coupler, 110mm D.S.R.-12.42.1, |
| 142 | 160mm |
| 143 | Vent Cowl 110mm |
| 144 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 15 mm dia pipe, D.S.R.-18.7.1 |
| 145 | 20 mm dia pipe, D.S.R.-18.7.2 |
| 146 | 25 mm dia pipe, D.S.R.-18.7.3 |
| 147 | 32 mm dia pipe, D.S.R.-18.7.4 |
| 148 | 40 mm dia pipe, D.S.R.-18.7.5 |
| 149 | 50 mm dia pipe, D.S.R.-18.7.6 |
| 150 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc. 15 mm dia nominal bore, D.S.R.-18.8.1 |
| 151 | 25 mm dia nominal bore, D.S.R.-18.8.2 |
| 152 | 32 mm dia nominal bore, D.S.R.-18.8.3 |
| 153 | Supply, installation , testing & commissioning of Nytril Rubber Insulation and polyshield outer mechanical protection (comprising of wrapping with poly glass tape helically wound and subsequently applying 2 coats of polyshield material (resin & hardner) as per manufacturers specification) on Hot and chilled water supply lines having thermal conductivity .038 W/mok 0.212 BTU / (Hr-ft2-oF/inch) at an average temperature of 30oC ,temperature range of –40oC to 105oC,Density of material shall not be less than 0.06 gm/cm3, class O type, complete as per manufacturer recommendation. 19 mm, D.S.R.-16.23.1.1 |
| 154 | 25 mm, D.S.R.-16.23.1.2 |
| 155 | Supply, installation , testing & commissioning of male/ female screwed end full way lever operated forged brass ball valve(PN 16) of brass body with brass ball & teflon seat tested to a pressure 24 Kg / sqcm with (threaded joints) complete as required. 15 mm nominal bore, D.S.R.-18.18.1 |
| 156 | 20 mm nominal bore, D.S.R.-18.18.2 |
| 157 | 25 mm nominal bore, D.S.R.-18.18.3 |
| 158 | 32 mm nominal bore. |
| 159 | 40 mm nominal bore |
| 160 | Supply, Installation, Testing and commissioning of slim seal type C.I. Butterfly valve confirming to IS 13592 (Body : Grey Cast Iron, shaft : SS, Disc : SG Iron (Rilson coated), Liner : HT - EPDM) of approved make with PN 16 rating flange dimensions shall be confirming to IS 6392, washer, nuts & bolts. Rated to temperature of 85 Deg C and tested to a pressure not less than 24 Kg/Sq.cm. 50 mm nominal bore, D.S.R.-19.19.1 |
| 161 | 65 mm nominal bore, D.S.R.-19.19.2 |
| 162 | 80 mm nominal bore |
| 163 | Supply, installation , testing & commissioning of gun metal vertical non return valve conforming to IS 778 of approved quality (screwed end) including union, nipple, fixing on pipe complete as required.(PN 16). 50 mm nominal bore, D.S.R.-19.19.1 |
| 164 | 65 mm nominal bore, D.S.R.-19.19.2 |
| 165 | Providing, fixing, testing and commissioning of CI `Y' strainer for pressure of 16 kg / sq.cm with bronze perforated sheet basket including rubber gasket, flanges ( test pressure of 24 kg / sqcm), nuts, bolts and washers, panting of the same complete as required and suitable for system pressure. 50 mm dia |
| 166 | 65 mm dia |
| 167 | Providing and fixing motorized valve including control wiring upto panel & ON/OFF arrangement and all other accessories required to make the system complete including control unit to be made of good quality PVC box, as per IP 65 with cable gland also as per IP 65 and suitable for outdoor installation complete with suitable wiring. This unit should be suitable to operate solenoid valve, float switch and consisting of contactors, control transformer, MCB, Potential free contacts for BMS, indicating lamp for automatic operation of filling OH tank with level to be maintioned between 70% (low) to 100% (full). 50 mm nominal bore, D.S.R.-19.19.1 |
| 168 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group B, D.S.R.-1.10.2 |
| 169 | Group C, D.S.R.-1.10.3 |
| 170 | Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. D.S.R.-1.11 |
| 171 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. D.S.R.-1.12 |
| 172 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire, D.S.R.-1.14.1 |
| 173 | 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire, D.S.R.-1.14.2 |
| 174 | 2 X 6 sq. mm + 1 X 6 sq. mm earth wire, D.S.R.-1.14.4 |
| 175 | 4 X 6 sq. mm + 2 X 6 sq. mm earth wire, D.S.R.-1.14.9 |
| 176 | 4 X 10 sq. mm + 2 X 6 sq. mm earth wire, D.S.R.-1.14.10 |
| 177 | 4 X 16 sq. mm + 2 X 6 sq. mm earth wire, D.S.R.-1.14.11 |
| 178 | Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 Pair, D.S.R.-1.18.2 |
| 179 | Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. D.S.R.-1.19 |
| 180 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm, D.S.R.-1.21.1 |
| 181 | 25 mm, D.S.R.-1.21.2 |
| 182 | 32 mm, D.S.R.-1.21.3 |
| 183 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Telephone socket outlet, D.S.R.-1.24.6 |
| 184 | TV antenna socket outlet, D.S.R.-1.24.7 |
| 185 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. D.S.R.-1.25 |
| 186 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. D.S.R.-1.26 |
| 187 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm), D.S.R.-1.27.1 |
| 188 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. D.S.R.-1.31 |
| 189 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. D.S.R.-1.32 |
| 190 | Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. As required. D.S.R.-1.33 |
| 191 | Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required. D.S.R.-1.38 |
| 192 | Supplying and fixing PVC batten/ angle holder including connections etc. as required. D.S.R.-1.58 |
| 193 | Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as equired. Group B, D.S.R.-1.10.2 |
| 194 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings). D.S.R.-1.56 |
| 195 | Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, \\"C\\" curve including connections, painting etc. as required. D.S.R.-1.57 |
| 196 | Supplying,installation,testing and commissioningof Passive Infrared(PIR) technology based occupancy sensor having high preformance, non regulating programmable type, suitable for connected load upto 10Amp , for mounting height up to 3 mtr and for 5 m diameter coverage area along with necessary fixing arrangements i/c programming at site etc. complete as required. D.S.R.-7.1 |
| 197 | Supply and fixing of max. 18-22 Watt LED Batten fitting with Extruded Aluminum housing, special polycarbonate diffuser for glare free light distribution and suitable mounting for on both surface & suspended, complete in all respect. 2160-2640 system lumens, >120 Lm/W, PF>0.95, THD <10%, CRI>80, >300V over voltage protection, 2.5 KV internal Surge Protection, with 3 year warrantee. CATT-AAA. UPSOR 23.08 |
| 198 | Supplying, fixing, connecting, testing and commissioning of LED mirror light luminaire with 10W watt complete with electronic ballast, lamp including connection etc. complete as required,Including connection with 1.5 sqmm FRLS PVC insulated copper conductor similar to Philips Cat. No. ULTRON, STYLISH LIVING |
| 199 | Supply & fixing of water tight oblong 10 watt LED Bulkhead luminai having pressure die cast housing with driver set confirming to IP65 and above protection, IK 08, High purity transmisivity UV Stabilized Non yellowish diffuser/ for uniform light distribution, detachable driver set, open and short circuit protection suitable for 24 Hr Continuous Operation, Complete in All respect. 1200 sstem lumens, >120 Lm/W, PF>0.95, CRI>70, >300V over voltage protection, 4 KV internal surge Protection, metal housing with 5 years warrantee. |
| 200 | Supply & Fixing of Step Light IP 44 2 W , total 80 system lumes, PF>0.95, THD<10%, CRI>80, > 300V over voltage protection, dimensions: 108 x 108 x 52 mm having power coated die cast al. housing. |
| 201 | Supply & Fixing of Rope Light in cove, IP 65, 120 l/w, 8 watt/ meter |
| 202 | Supplying, erection, connecting, testing and commissioning of 200 mm 900 rpm exhaust fan complete with gravity louver and connection with 3 core flexible wire as required. |
| 203 | Supplying, erection, connecting, testing and commissioning of 300 mm 900 rpm exhaust fan complete with gravity louver and connection with 3 core flexible wire as required. |
| 204 | Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. DSR 19.1 |
| 205 | Providing, supplying, installation, testing and commissioning of LED track mounted spot light, made of die-cast aluminium housing, complete with integrated LED driver, reflector optics with clear glass cover, suitable for mounting on standard single-phase track, including all accessories, wiring from track connector, fixing hardware, and making good the surface, as required. Wattage : 20W, Colour temperature: As specified by Engineer-in-Charge (3000K / 4000K / 5700K). Finish: White / Black |
| 206 | Providing, supplying, installation, testing and commissioning of LED curved linear suspended luminaire made of extruded aluminium profile with powder coated / anodized finish, complete with integrated LED modules, electronic driver, milky diffuser for uniform glare-free illumination, suspension kit with adjustable cables, ceiling fixing accessories, internal wiring, and making good the surface, complete as per approved lighting drawings and as directed by Engineer-in-Charge. Profile size: 100×77 mm (W×H). Wattage: 30W (or as per approved lighting layout), Mounting: Suspended from ceiling. Shape: Curved / custom geometry as per lighting design |
| 207 | Providing, supplying, installation, testing and commissioning of LED linear box type luminaire of width 55 mm, made of extruded aluminium housing with powder coated / anodized finish, complete with high efficacy LED modules, electronic driver, prismatic / PMMA diffuser for uniform light distribution, end caps, suspension kit or surface mounting accessories, internal wiring, fixing hardware, and making good the surface, complete as per specifications and as directed by Engineer-in-Charge. Profile size (W×H): 55 × 73 mm. Length options: 600 mm / 1190 mm / 1780 mm / 2370 mm (linkable for customized length). Wattage options: 10W–72W (as per selected length and lighting design). Mounting: Suspended or Surface mounted. Finish: White / Black / As specified |
| 208 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator). 8 way , Double door, D.S.R.-2.3.3 |
| 209 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator). 6 way (4 + 18), Double door, D.S.R.-2.4.2 |
| 210 | 8 way (4 + 24), Double door, D.S.R.-2.4.3 |
| 211 | Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.). 4 way (4 + 12), Double door, D.S.R.-2.5.1 |
| 212 | 8 way (4 + 24), Double door, D.S.R.-2.4.3 |
| 213 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole, D.S.R.-2.10.1 |
| 214 | Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. D.S.R.-2.11 |
| 215 | Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 Amp. D.S.R.-2.12.1 |
| 216 | 63 Amp. D.S.R.-2.12.2 |
| 217 | Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A, D.S.R.-2.13.1 |
| 218 | 63 A, D.S.R.-2.13.2 |
| 219 | 100 A, D.S.R.-2.13.3 |
| 220 | Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 25 A, D.S.R.-2.14.1 |
| 221 | 40 A, D.S.R.-2.13.1 |
| 222 | Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A \\"C\\" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required. |
| 223 | Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness, D.S.R.-4.1.4 |
| 224 | Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness, D.S.R.-4.1.4 |
| 225 | Supplying and installing following size of perforated painted with powder coating M.S. cable trays Tee with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness, D.S.R.-4.1.4 |
| 226 | Supplying and installing following size of perforated painted with powder coating M.S. cable trays Cross Member with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. 300 mm width X 50 mm depth X 1.6 mm thickness, D.S.R.-4.1.4 |
| 227 | Supply of Roof conductor holder for parapet- Polyamide Conductor holder:With M8 female thread or diameter 7mm, M8 Screw to connect the conductor holder.Weather and temperature resistant from -35 to +90 degree Celsius tested. Conductor holder @ 1 meter distance |
| 228 | Polyamide roof cable holder for flat roof DIN 48829 Form B1. Closed form with bottom. Filling weight 1Kg (frost-resistant concrete). Sleeve from polyethylene, black @ 1 meter distance. |
| 229 | Vertical air terminal with accessories:Providing of Air terminals as per IS-IEC -62305 part-3 Nominal size Ø10/16 mm aluminium rod: 2 Mtr Airterminal: semi-hard ;Suitable for high wind load. |
| 230 | Vertical air terminal with accessories:Providing of Air terminals as per IS-IEC -62305 part-3 Nominal size Ø10/16 mm aluminium rod: 4 Mtr Airterminal: semi-hard ; Suitable for high wind load. |
| 231 | Providing of Stand for Fang Fix system 16 kg made up of frost resistant concrete. |
| 232 | Providing of Stand for Fang Fix system 16 kg with base and clamp ,made up of frost resistant concrete and clamp tested upto 100KA lightning current . |
| 233 | Connector: For T cross and parallel connectors. Quick installation using hexagonal bolt M10X30 high-grade hot dip galvanised. Conforms to the requirements according to DIN VDE 0185-305 (IS-IEC 62305) |
| 234 | Providing of expansion piece with connector: For equalising temperature related length changes. Necessary on conductors length over 20 meters. For round conductor Rd 8/ALU. |
| 235 | Connector: For T cross and parallel connectors. Quick installation using hexagonal bolt M10X30 high-grade hot dip galvanised. Conforms to the requirements according to DIN VDE 0185-305 (IS-IEC 62305)(2nos/expansion piece). |
| 236 | Supply of 8 mm Aluminum Round Conductor complete as specified in drawing & Meets the requirements of VDE 0185-305 (IS/IEC 62305) |
| 237 | Supply of Roof conductor holder for parapet- Polyamide Conductor holder:With M8 female thread or diameter 7mm, M8 Screw to connect the conductor holder.Weather and temperature resistant from -35 to +90 degree Celsius tested. Conductor holder @ 1 meter distance |
| 238 | Supply of Test Joint (Folding Clamp) suitable to connect 8mm round conductor and max by 30x3 mm GI strip as specified in drawing and directed by Engineer |
| 239 | Supply of Galvanised Steel Flat 30X3 mm thickness from earth electrode directly in ground as required. Flat conductor Hot Dipped Galvanized. |
| 240 | Providing of Cross connector for Flat: Suitable for 30mm Galvanised steel strip. Installed with 4 nos of hexagonal plate. |
| 241 | Providing of flat conductor holder suitable for FL 30. Installed with 2 hexagonal bolts. |
| 242 | Providing of Plastic Corrosion Protection strip: Approx 1.1 mm thick. Width 50mm. Made of petrolatum- coated chemical fibre fabric. |
| 243 | Supply of UL Listed & CPRI Tested maintenance free ,Low carbon copper coated earth rod of 3 metre electrode having diameter of 14 mm with copper coating thickness of 250micron tested as per IEC 62561-2 . |
| 244 | Universal clamp made of SS to connect rod with flat conductor |
| 245 | Earth conductivity enhancing compound shall be of 25 kg/pit tested as per IEC 62561-7,TCLP tested. |
| 246 | The above arrangements shall be provided with Heavy duty earth champer of 5000kg load bearing capacity to ensure the safety of earthing system . |
| 247 | Supply, installation, testing and commissioning of Equipotential Bonding Busbar |
| 248 | Providing erecting and testing of 4.0MP IP Vandal Proof Dome Camera, 2.8mm Fix Lens, Four (4) H.265 or Higher Streams, Built-in Mic and Speaker, Storage slot suitable for 1TB SD/SDHC/SDXC memory, IP67, IK10, OEM registered MAC ID. |
| 249 | Providing erecting and testing of 4.0MP IP Metal Casing Bullet Camera, 8.0mm Fix Lens, 50 MTR IR., Four (4) H.265 or Higher Streams, Built-in Mic and Speaker, Storage slot Suitable for 1TB SD/SDHC/SDXC memory, IP67, OEM registered MAC ID. |
| 250 | Providing erecting and testing of 4.0MP IP PTZ Dome Camera, 30X, 4.5mm~135mm Lens, Four (4) H.265 or Higher Streams, Built-in Mic and Speaker, Storage slot suitable for 512 GB SD/SDHC/SDXC memory, IP67, OEM registered MAC ID. |
| 251 | Providing erecting and testing of 32CH NVR, H.265+, VGA, HDMI, 32Ch. *4K (8MP), 10/100/1000 Mbps, 2 x USB2.0, 1 x USB3.0, 4HDD X 10TB, 16 Alarm Input, 4 Alarm Output, FACE DETECTION, VEHICLE DETECTION, HUMAN DETECTION, ACTIVE DETERRENCE, PEOPLE COUNTING, BIS, CE, FCC, RoHS Certification. |
| 252 | Providing erecting and testing 8TB HDD for recording storage |
| 253 | Providing erecting and testing of 24 X 1G Base-T Copper POE+ Ports, 02 X 1G Base-X Fiber SFP. 190W Power Budget IEEE 802.1x, Guest VLAN, RADIUS based VLAN assignment via .1x, MAC-based .1x, RADIUS Accounting, Network Storm Protection, DoS, Dynamic ARP inspection, Broadcast, Unicast, Multicast DoS Protection CE mark, commercial, FCC Part 15 Class A, VCCI Class A, Class A EN 55022 (CISPR 22) Class A, Class A C-Tick, EN 50082-1, EN 55024, CCC Min. 5-year or Higher Hardware Replacement Warranty, Lifetime free latest firmware support, Replacement with New Product Only No repair\refurbished Products. |
| 254 | Providing erecting and testing of Jack Panel, fully loaded with 24 nos. UTP ports for PCB based IO Jacks (RJ45, TIA-568C Category-6, Installation and Termination of all 24 nos. Catergory-6 UTP , unloaded with individually replaceable 24 nos. Category-6 I/O Jacks complying with TIA-568.C.2, as per given jack specification Shall be suitable for loading unshielded & shielded jacks for different category systems (CAT 6 & CAT 6A). |
| 255 | Providing erecting and testing of Cable Manager for racK |
| 256 | Supply, Testing and commissioning of 5 Meter HDMI Cable for display. 4K UHD and HD compatible, 99.999% oxygen free copper conductors, Flexible, durable foil-insulated housing material increases ease of installation and product life Exceptional high speed performance for 4K UHD and HD 1080p displays with 3D, Perfect opaque plug end as well as excellent conductivity and protection against oxidation, Kink protection and strain relief to protect conductor. |
| 257 | Providing erecting and testing of 43\\" Full HD(1920X 1080) resolution LED display with built in 2.4 Ghz Wifi, 1.1 Ghz Built in Quad core processor, 1.5 GB DDR3 RAM, 8 GB Memory, built in Triple Core Mali 600 MHz GPU, with HDR 10, Dolby Audio, Built in Wifi and Cromecast, HDMI CEC, HDMI ARC, Built-in Bluetooth Ver.4, 20W built in speakers, HDMI 2.0 X 3, AV X 1, USB 2.0 X 1, RJ45 X 1(network connectivity only), Headphone Out x 1, SPDIF Out x 1, |
| 258 | Supply Installation Testing & Commissioning of 17U 600 x 600mm Indoor Floor mount Rack with required accessories like 6 socket PDU, 2/4 Fan, 2 Hardware Mounting Packet, 1 Equipment Tray. |
| 259 | Providing erecting and testing of company fabricated patch cords shall conform to Cat- 6 & conductor shall be stranded for better flexibility Shall support network line speeds up to 1 Gbps Shall have RJ-45 jacks. 1Mtr Patch Cord. |
| 260 | Providing erecting and testing of Camera Junction Box |
| 261 | (A) (a) Supplying, installation, testing and commissioning of electric driven terrace pump conforming to IS 12469: 2019 suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump). (b) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal as required. (c) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class- 'F' insulation, conforming to IS-12615: 2018. (d) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (e) Suitable cement concrete foundation duly plastered and with anti vibration pads. 27.4.1 900 lpm at 35 m Head Each 107744.00Supplying Installation , testing and commissioning of , complete in all respects , as required: (TERRACE Pump). 900 lpm at 35 m Head, D.S.R.-27.4.1 |
| 262 | Poviding laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 1239/3589 i/c fitting like elbow, tees, flanges,tapers, nuts bolts , gaskets etc. in ground including welding excavations & providing cement concrete blocks as supports , anticorrosive tratment with coltar / asphalt tape as pr IS 10221, refilling the trench etc. of following sizes complete as required. 150 mm dia, D.S.R.-27.6.2 |
| 263 | Poviding laying , testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including welding ,fitting like elbow, tees, flanges,tapers, nuts bolts , gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint required shade complete as required : 65 mm dia, D.S.R.-27.7.5 |
| 264 | 80 mm dia, D.S.R.-27.7.6 |
| 265 | 100 mm dia, D.S.R.-27.7.7 |
| 266 | 150 mm dia, D.S.R.-27.6.2 |
| 267 | Supplying ,fixing,testing and commissioning of Butterfly valve of PN 1.6 rating ISI marked complete with ns, bolts, washers,gaskets conforming ti IS 13095 of following sizes as required : 65mm dia, D.S.R.-27.11.3 |
| 268 | 80 mm dia, D.S.R.-27.7.6 |
| 269 | 100 mm dia, D.S.R.-27.7.7 |
| 270 | 150 mm dia, D.S.R.-27.6.2 |
| 271 | Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required. D.S.R.-27.13 |
| 272 | Providing, fixing, testing & commissioning of resilient Rubber bellows single arch vibration eliminators suitable for raw water up to 45 deg. C temperature, working pressure 8.5 Kg/cm2 and test pressure 14 Kg/cm2 to provide relief from stresses at pipe flanges. It should be complete as per manufacturer's specifications & as: 150 mm dia, D.S.R.-27.6.2 |
| 273 | Providing , Intalllation, testing and commissioning of Non - Return valve of following sizes complete with rubber gasket, GI bolts, nuts, washers etc. as required:150 mm dia, D.S.R.-27.6.2 |
| 274 | Providing , Intalllation, testing and commissioning of Y-strainer fabricated out of 1.6 mm thick stailnless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 150 mm dia, D.S.R.-27.6.2 |
| 275 | Providing fixing, testing & commissioning of Foot Valve connection 150 mm |
| 276 | Providing, fixing, testing & commissioning of Air release valve with 25mm dia |
| 277 | Providing and fixing of Pressure switch in M.S. pipe line including connection etc. as required :, D.S.R.-27.22 |
| 278 | Providing and fixingin position the industrial type Pressure gauge with brass valve complete as required. |
| 279 | Supplying & fixing single headed External yard hydrant valve with 1 No.63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (Tpe- A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Stainless steel, D.S.R.-27.1 |
| 280 | Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required. Single headed Stainless steel, D.S.R.-27.9.2 |
| 281 | Supplying and fixing 63 mm dia, 30 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets conforming to IS 636 (type-A) as required : Stainless Steel (Grade 304), D.S.R.-27.16.2 |
| 282 | Supplying and fixing first - aid Hose Reel with MS construction spray painted in post office red, conforming ti IS 884 complete with the following as required : (a) 20 mm nominal internal dia water hose thermoplastic (Textile reinforced ) type-2 as per IS: 12585, (b) 20 mm nominal internal dia gun metal globe valve & nozzle. (c ) Drum and brackets for fixing the equipments on wall. (d) Connections from riser with 25 mm dia stop gun metal valve & M.S. pipe and socket.30m, D.S.R.-27.17.1 |
| 283 | Supplying and fixing 63 mm dia, gun metal short branch pipe with 20 mm nominal internal diameter size nozzle confoming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Stainless Steel (Grade 304), D.S.R.-27.16.2 |
| 284 | Supplying and fixing of fire brigade connection of cat iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 3-way -150 mm dia M.S. Pipe, D.S.R.-27.19..3 |
| 285 | Supply, installation, testing and commissioning approved make ball valves with screwed ends confirming to IS 1703 -1977 with unions, etc.including all the necessary fixing materials complete.50mm dia |
| 286 | 40mm dia |
| 287 | Providing and fixing standard fire mans axe with heavy duty insulated rubber handle. |
| 288 | ISI marked Carbon di-oxide type fire extinguisher, Capacity 4.5 kg, Filled with CO2 gas having purity 99.7% complied with IS 15222, manufactured and tested as per IS 15683: 2018, Fire Rating 55B, Wheel Type valve made of brass conforming to IS 3224, In-built Pressure relief device (Fusible plug and Rupture Disc Type), ISI marked CO2 cylinder conforming to IS 7285 Part 1 or Part 2, High glossy PU paint for anticorrosion on external surface, Metal wire braided hose shall have minimum bursting pressure of 250 Kgf/cm2. Horn with metallic thread connection, Body Handle with Rubber Grip, Aluminium siphon tube (Grade as per IS 738), Wall mounting brackets & screws, Cylinder body punched with Year of manufacturing and test pressure as per BIS requirement, UV resistant Vinyl label, QR code for product traceability, Testing and Inspection - As per IS 15683:2018 CE and EN 3-7 & 8 |
| 289 | ISI Marked Dry Powder Agent ABC Type Fire Extinguisher, Capacity 6 Kg MAP 90%, Fire rating 4A 144B, Deep drawn cylinder body, Internal and external surface of cylinder pure polyester powder coated for corrosion resistance, Squeeze Grip Valve with OEM Brand made of forged brass with nickel chromium plating, In built pressure release device & NRV at pressure gauge mounting port, Polyvinyl Chloride Siphon Tube, Stainless Steel safety pin, EPDM hose with Nylon 6 nozzle, Nozzle fitted with brass threaded insert and blow off cap, High Quality Vinyl label, QR code for product traceability, Testing and Inspection - As per IS 15683:2018. CE and EN 3-7 & 8 |
| 290 | Supply, installation, testing and commissioning of outdoor fire hydrant hose cabinet (double door type) fabricated from 16 SWG CRCA mild steel sheet, of size approx. 750 mm (H) × 600 mm (W) × 300 mm (D), suitable to house two numbers of 63 mm dia × 15 m long RRL hose pipes with coupling, one branch pipe and nozzle. The cabinet shall be of double-door construction with stainless steel hinges, locking handle, and stay-arms, provided with 4 mm thick clear acrylic front vision panel, continuous EPDM/neoprene rubber gasket for weatherproofing, ventilation louvers, and finished with epoxy-based powder coating in fire red shade (RAL 3001) over anti-corrosive primer. The cabinet shall be weatherproof, lockable and wall/pedestal mounted on suitable angle iron frame, and supplied with all fixing hardware and accessories. |
| 291 | Supplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop and loop length up to 2 km, network communication card, minimum 320 character graphics/ LCD display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory (EPROM), power supply unit (230 ± 5 % V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall have facility to connect printer to printout log and facility to have seamless integration with analog/digital voice evacuation system (which is part of the schedule of work under SH: PA System) and shall be complete with all accessories . The panel shall be compatible for IBMS system with open protocol BACnet/ Modbus over IP complete as per specifications. Four loop panel |
| 292 | Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required. D.S.R.-28.2.4 |
| 293 | Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required, D.S.R.-28.2.5 |
| 294 | Supplying, installation, testing & commissioning of intelligent address -able programmable sounder complete as required. D.S.R.-28.2.6 |
| 295 | Supplying, installation, testing & commissioning of fault isolator compl-ete with base as required. D.S.R.-28.2.7 |
| 296 | Supplying, installation, testing & commissioning of addressable fire control module complete as required. D.S.R.-28.2.10 |
| 297 | Supplying, installation, testing & commissioning of addressable phone control module complete as required. D.S.R.-28.2.11 |
| 298 | Supplying, installation, testing & commissioning of intelligent addres-sable duct detector including suitable Photo detector complete with base as required, D.S.R.-28.2.13 |
| 299 | Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required. D.S.R.-28.2.15 |
| 300 | Supplying, installation, testing & commissioning of addressable manual call point complete as required. D.S.R.-28.2.14 |
| 301 | Supplying, installation, testing & commissioning of fire fighter tele-phone handset complete as required. D.S.R.-28.2.17 |
| 302 | Supplying, installation, testing & commissioning of of Intelligent Addr-essable, Supervised Monitor Module monitoring Potential-free, Normally Open Dry Contact input. The Monitor Module shall have operating temperature range from 0°C to 70°C and a humidity tolerance of up to 93% RH, Non-Condensing with weatherproof enclosure |
| 303 | Supplying & laying of 2x1.5 sqmm fire survival armoured cable,600 /1000V rated with annealed copper conductorhaving glass mica fire barrier tape covered by an extrudedlayer of Cross Linkable Ethylene Propylene Rubber (EPR)insulation and LSZH inner bedding,steel wire armouring &LSZH outer sheath complete as required.. D.S.R.-28.5.1 |
| 304 | Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required. D.S.R.-28.3.1 |
| 305 | Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required. D.S.R.-28.3.2 |
| 306 | Supplying, installation, testing & commissioning of ceiling/wall mounted loud speaker, 3/1.5 Watt in ABS enclosure complete as required. D.S.R.-28.3.4 |
| 307 | Supplying, installation, testing & commissioning of digital audio amplifier 50 Watt, 25V rms operating at 240 volt AC supply complete as required. D.S.R.-28.3.6 |
| 308 | Supplying, installation, testing & commissioning of Voice command key-pad 6 zone, with microphone assembly complete as required. D.S.R.-28.3.9 |
| 309 | Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. speaker cable Two pair, 2-core, 1.5 sqmm, D.S.R.-28.5.3.2 |
| 310 | Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as required. D.S.R.-28.5.4 |
| 311 | Supplying, Installation, Testing & Commissioning of Modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling/heating having 100% hermetically sealed inverter type twin Rotary/Scroll Compressor(s),minimum two compressors (with individual separate PCB) for above 14HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R-410-A Refrigerant or equivalent, vibration Isolators with suitable foundation etc. complete as required. To have better efficiency condenser fan shall be capable to operate at different speed with respect to load.The unit shall deliver the rated capacity and in confirmation as per IS18728:2024 and CPWD Specifications and work even at 50°C ambient temperature without tripping. The system shall be able to deliver 100% of the rated capacity upto 39°C. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply and BMS compatible. The unit shall be filled with first charge of the refrigerant and ready for use as required. The condenser should be coated with a hydrophilic film to prevent water accumulation on the surface of the heat exchanger, enhance water dispersion, and reduce the risk of degradation, thereby improving overall performance and durability. The Indian Seasonal Energy Efficiency Ratio (ISEER) of the unit shall be as per Energy Conservation and Sustainable Building Code (ECSBC) 2024 as below and complete as per CPWD specification, connections, inter connections etc. as required. (For capacity <40 kWr ISEER 7.4, Capacity > 40 and <70 ISEER 7.5, Capacity > 70 ISEER 7.6 for Super ECSBC Building). 22 HP |
| 312 | 16 HP |
| 313 | Supplying, Installation, Testing and Commissioning of following minimum capacity High wall type Indoor unit equipped with and comfort washable synthetic media prefilter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, cord less remote control, drain pan, necessary accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single phase AC supply, complete as required. The Indoor units must shut down upon receiving a singal from the BMS System / Fire Singnals. The system shall be capable to adjust air flow as per room requirement automatically. The cooling capacity of indoor unit will be at air inlet conditions of 27°C DB and 19°C WB temperature. (Make will be same as of Outdoor). 1.2 TR |
| 314 | 2.0 TR |
| 315 | Supplying, Installation, Testing and Commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted mid high static ductable type Indoor unit equipped with washable synthetic media prefilter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration Isolators, drain pan, drain pump, other necessary supports etc., suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Singnals. The system shall be capable to adjust air flow as per room requirement automatically. The cooling capacity of indoor unit will be at air inlet conditions of 27°C DB and 19°C WB temperature. (Make will be same as of Outdoor) High Static Ductable units (minimum 49 to 77 pascal external static pressure). 4.0 TR |
| 316 | 4.6 TR |
| 317 | Supplying, Installation, Testing and Commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted mid high static ductable type Indoor unit equipped with washable synthetic media prefilter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration Isolators, drain pan, drain pump, other necessary supports etc., suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Singnals. The system shall be capable to adjust air flow as per room requirement automatically. The cooling capacity of indoor unit will be at air inlet conditions of 27°C DB and 19°C WB temperature. (Make will be same as of Outdoor) High Static Ductable units (minimum 78 pascal external static pressure). 5.5 TR |
| 318 | 8.0 TR |
| 319 | Supply,Installation,testing and commissioning of centralised remote controlers as per drawing and specifications |
| 320 | Supplying, Installation, Testing and Commissioning of Y/T/Multi Joints. Joints shall be of same Original Equipment Manufacturer (OEM) make as of ODUs and IDUs. Indoor Units |
| 321 | Outdoor Multi Joints |
| 322 | Supplying , Installation, Testing and Commissioning of Air Cooled Hi Wall split type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU) i/c drain pipe R-32/R-410/ R-407 Green Refrigerant, wireless Remote control, suitable for working between 180- 260V with low & high voltage cutoff and 50 hz ,1 phase AC supply capable of performing cooling, humidification, air circulation of following capacity with Scroll / rotary compressor. The system shall be able to deliver 100% of the rated capacity upto 42 C. Min 5 year Original Equipment Manufacturer (OEM) warranty both compressor and Printed Circuit Board (PCB). Must comply : Electrical cable IS 694 or IS 9968 temperature sensing control IS /International Electrotechnical Commission (IEC) 60730, hermetic compressor IS 10617, heat exchanger IS 11329, capacitor IS 2993 and motor IS 12615. Complete as per CPWD specification and IS : 1391 Part II 2023. The system shall be able to operate up to 50 C (out door ambient temperature). Inverter Type - Cooling only. 2.0 TR with 5 Star BEE Rating |
| 323 | Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 324 | 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 325 | 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 326 | 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 327 | 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 328 | 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 329 | 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation |
| 330 | 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation |
| 331 | 41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick insulation |
| 332 | Supply & fixing of control cum transmission wiring of 2 C X 1.5 Sq. mm Copper conductor cable alongwith conduite for looping between indoor & outdoor VRF system. |
| 333 | Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable 1.1 KV grade to be erected as directed of following size. 3C x 2.5 sq.mm |
| 334 | Supply,installation,testing and commissioning of of CPVC pipes having thermal stability for condesate water including wrapping of 9mm thick class 0 nitrile rubber insulation with suitable adhesive with all CPVC plain and brass threaded fittings including the pipes with clamps 1metre spacing.This including jointing of pipes with one step CPVC solvent cement and testing of joints complete as per drg and specifications. 40 mm dia. |
| 335 | 32mm dia. |
| 336 | 25 mm dia. |
| 337 | Supply, installation, testing and commissioning of floor mounted / ceiling hang Axial flow type supply air fan for Lift well, lobby & stairwell pressurization of following capacity with powder coated GSS/M.S. casing and aluminium alloy impellers with high efficiency aero-foil sections, blades, the impeller directly driven by TEFC induction motor (efficiency 1) and 'F' class insulation suitable for 3 Phase, 50 Hz, 415±10% Volt, TP isolator with M.S enclosure box complete as required and as per specifications. Fans should be statically & dynamically balanced.The fan static pressure shall be 20 mm WC static. as per site condition. 2000 CFM @ 30MM Static Pressure (for lift) |
| 338 | Supply, Installation, Testing & Commisioning of AMCA Certified (For Air and Sound Performance) tube axial flow fans of different capacities in standard GI / M.S. contruction as mentioned below. Entire fan model and AMCA Seal shall apear in techncial submittal of fan. All the fans shall be synthetic enamel painted/ hot dip galvanized with minimum 220 GSM Zinc Coating and complete. The electric motor coupler shall be IE-02 squirrel cage induction type conforming to IS-325, IP-55 rated with class `H' insulation. Motor shall be of high temperature resistance \\"Class H Smoke Spill\\" 250°C for 2 hours. Fans shall be EN 12101-3 Certified and CE/UL Listed for high temperature. Motor make shall be same as that mentioned on the fire certificate. Fan efficiency should not be less than 65%, and noise level should not be more than 70 db @ 3 m distance when measured under hemisperical reverberant room conditions. Quoted price shall be inclusive of sound attenuator at the outlet of the fan as shown in the approved shop drawings, all accessories, vibration isolators,mounting brackets/feet/ duly enamel painted M.S structure etc. Fans mentioned as outdoor type shall be good for outdoor installation mounting arrangement as per approved shop drawings. Fans shall be as per specifications like it should be fitted with Control Module with 2x1.5 Sqmm armoured cable with Fire Alarm control module for automatic operation in case of fire. 8000 cfm at 50 mm static Pressure |
| 339 | 5500 cfm at 50 mm static Pressure |
| 340 | 5000 cfm at 50 mm static Pressure |
| 341 | 3000 cfm at 50 mm static Pressure |
| 342 | 2500 cfm at 50 mm static Pressure |
| 343 | 2000 cfm at 50 mm static Pressure |
| 344 | Supply, installation, testing & commisioning of Circular Inline fan for OT exhaust/ toilet /fresh air shall be complete with SISW non-stalling backward curved centrifugal Impeller, GSS Casing, direct driven Single phase(230 V±10%, 50 Hz.) external rotor Motor with IP44 Protection & Class B Insulation with speed regurator ,canvas connection & all accessories as required. Fan shall be AMCA Certified for Air & Sound Performance. Noise Level shall not exceed 60 dB (A) at 3 meters at room condition. 1100 CFM /15 mm SP |
| 345 | 1000 CFM /15 mm SP |
| 346 | Supplying, installation, testing & commissioning of Propeller type exhaust air fans suitable for following capacities complete with electric motor suitable for operation on 220 V+ 10%,50 Hz, 1 phase AC supply fitted with speed regulator, mountings, frames, louvers and bird screen etc. of the following capacities. 200 MM DIA |
| 347 | Supplying, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/ round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports, bends, transitions, reducers, end caps, collars etc as required complete in all respect in confirmation with IS : 655 and approved drawings and specifications of following sheet thickness complete as required. Thickness 0.63 mm Sheet |
| 348 | Thickness 0.80 mm Sheet |
| 349 | Supplying, installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages,flanges etc in confirmation to SMACNA/IS and as per specifications complete etc. as required. |
| 350 | Supply, installation, testing and commissioning of Motorized (ON-OFF Type) duct mounted GI volume control damper with enthalpy sensor and necessary control wire for integration within AHU room complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc in confirmation to SMACNA/IS and as per specifications complete etc. as required. Damper |
| 351 | Actuator |
| 352 | Supply,installation,testing and commissioning of flexible duct connections constructed of fire resistance flexible double canvas sleeve as per the drawings and specifications. |
| 353 | Supplying, Fixing, installation, testing and commissioning of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers in confirmation to SMACNA/IS and as per specifications complete etc. as required. |
| 354 | Supplying, Fixing, installation, testing and commissioning of powder coated extruded aluminium Return Air Grills but without volume control dampers in confirmation to SMACNA/IS and as per specifications complete etc. as required. |
| 355 | Supplying, Fixing, installation, testing and commissioning of Return air diffusers of powder coated aluminium without volume control dampers with anti smudge ring & removable core in confirmation to SMACNA/IS and as per specificationscomplete etc. as required. |
| 356 | Supply , Erection of Fresh / Exhaust air LOUVER with extruded aluminium grill with SS wire mesh with 20 micron filters |
| 357 | Supplying, Fixing, installation, testing and commissioning of thermal insulated flexible duct of following sizes duly supported at regular interval as per site requirement etc. in confirmation to SMACNA/IS and as per specifications complete etc. as required. 200MM Dia. |
| 358 | Supplying and fixing of following thickness duly laminated aluminium foil of mat finish closed cell Nitrile rubber (Class \\"O\\") insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. 19 MM |
| 359 | Supplying and fixing 50 mm thick aluminium foil faced esin bonded fibre glass insulation (on duct ) of density 24 kg/cu.m or mineral wool insulation(non-combustible) of density 44 kg/cu m after applying two coats of cold setting adhesive (CPRX compound) sealing all joints with self adhesive aluminium tape & covering with 0.63mmx19mm GI wire mesh netting butting all joints and laced with GI wire complete as per specifications and as required. (for indoor applications). |
| 360 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil, Lvl. 0.0 to 1.50 mt. D.S.R.-2.8.1 |
| 361 | Filling available excavated earth (excluding rock) in trenches, plinth,sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. D.S.R.-2.25 |
| 362 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), D.S.R.-4.1.8 |
| 363 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. D.S.R.-2.27 |
| 364 | Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement:2 coarse sand) to match the existing floor. With Chlorpyriphos/ Linadane E.C. 20% with 1% concentration. D.S.R.-2.35.3.1 |
| 365 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering,finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). D.S.R.-5.3 |
| 366 | As in item no. 6 above but for slabs (Using 1:1.5:3 Mix concrete). D.S.R.-5.3 |
| 367 | As in item 6 but for the lighter beams i.e. having spans upto 6 m. D.S.R.-5.3 |
| 368 | As in item 6 above but in R.C.C. Raft foundation and footing with approved stone ballast. (Using 1:1.5:3 Mix concrete), D.S.R.-5.1.2 |
| 369 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :, D.S.R.-5.2.2 |
| 370 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand), D.S.R.-6.1.2 |
| 371 | Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size). D.S.R.-4.10 |
| 372 | Painting on D.P.C. with two coats of airblown bitumen 85/50 or 85/25 @ 1.7 kg/sqm approx. including cost of fuel if any. D.S.R.-4.13 |
| 373 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand), D.S.R.-6.4.2 |
| 374 | Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in anover all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. D.S.R.-5.22.6 |
| 375 | 15 mm cement plaster on rough side of single or half brick wall of mix : 1:4 (1 cement: 4 coarse sand). D.S.R.-13.5.1 |
| 376 | 15 mm cement plaster on rough side of single or half brick wall of mix:1:6 (1 cement: 6 coarse sand), D.S.R.-13.5.2 |
| 377 | 12 mm cement plaster of mix :1:6 (1 cement: 6 coarse sand), D.S.R.-13.4.2 |
| 378 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth, D.S.R.-4.17 |
| 379 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. D.S.R.-11.3.1 |
| 380 | Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. D.S.R.-11.6.1 |
| 381 | Mild steel or iron work Providing and fixing mild steel round holding down bolts with nuts and washer plates complete. D.S.R.-10.19 |
| 382 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works, D.S.R.-10.25.2 |
| 383 | Z-Section steel windows (openable), D.S.R.-10.11.2 |
| 384 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes, D.S.R.-10.30.1 |
| 385 | Distempering with oil bound washable distemper of approved brand New work (two or more coats) over and including water thinnable priming coat with cement primer, D.S.R.-13.41.1 |
| 386 | Finishing walls with water proofing cement paint of required shade New work (Two or more coats applied @ 3.84 kg/10 sqm), D.S.R.-13.44.1 |
| 387 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade.Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture : (M.S. works). D.S.R.-13.62.1 |
| 388 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm. D.S.R.-22.7.1 |
| 389 | Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover, D.S.R.-10.6.1 |
| 390 | Providing & fixing ball bearing for rolling shutters. D.S.R.-10.7 |
| 391 | Interlocking tiles in courtyard |
| 392 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Ordinary cement without any pigment, D.S.R.-11.20.1 |
| 393 | Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns, etc. for mass concrete, D.S.R.-5.9.1 |
| 394 | Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick, D.S.R.-5.9.20 |
| 395 | Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick, D.S.R.-5.9.21 |
| 396 | Columns, Pillars, Piers, Abutments, Posts and Struts, D.S.R.-5.9.6 |
| 397 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil |
| 398 | Filling available excavated earth (excluding rock) in trenches, plinth,sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. D.S.R.-2.25 |
| 399 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), D.S.R.-4.1.8 |
| 400 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand), D.S.R.-6.1.2 |
| 401 | Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size). D.S.R.-4.10 |
| 402 | Painting on D.P.C. with two coats of airblown bitumen 85/50 or 85/25 @ 1.7 kg/sqm approx. including cost of fuel if any. D.S.R.-4.13 |
| 403 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand), D.S.R.-6.4.2 |
| 404 | 12 mm cement plaster of mix :1:6 (1 cement: 6 coarse sand), D.S.R.-13.4.2 |
| 405 | 15 mm cement plaster on rough side of single or half brick wall of mix:1:6 (1 cement: 6 coarse sand), D.S.R.-13.5.2 |
| 406 | Mild steel or iron work of small sizes and sections such as holding down bolts, hold fast tierods,gratings etc. (when not included in an over all rates) wrought to required from including supply of steel and its wastage including cost of bolts, nuts if required for and welding, grinding and making holes as required completion of work fabrication of holes doors, chaukhats nosing. (Grill) |
| 407 | Finishing walls with water proofing cement paint of required shade New work (Two or more coats applied @ 3.84 kg/10 sqm), D.S.R.-13.44.1 |
| 408 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade.Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture : (M.S. works). D.S.R.-13.62.1 |
| 409 | Fencing with angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately). Payment to be made per metre cost of total length of barbed wire used. With G.I. barbed wire |
| 410 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil |
| 411 | Filling available excavated earth (excluding rock) in trenches, plinth,sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. D.S.R.-2.25 |
| 412 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), D.S.R.-4.1.8 |
| 413 | R.C.C. work with cement approved coarse sand and 20 mm. guage approved stone grit im the proportion of 1:1.5:3 in lintels of doors and windows excluding supply of reinforcement and its fixing and binding the same with 24 BWG binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works. strength of the concrete shall not beless than M-20. |
| 414 | Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in anover all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level. D.S.R.-5.22.6 |
| 415 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand), D.S.R.-6.1.2 |
| 416 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. D.S.R.-2.25a |
| 417 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. D.S.R.-2.27 |
| 418 | 15 mm cement plaster on rough side of single or half brick wall of mix : 1:4 (1 cement: 4 coarse sand). D.S.R.-13.5.1 |
| 419 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. D.S.R.-11.3.1 |
| 420 | Centering and shuttering including strutting, propping etc. and removal of form for: Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick, D.S.R.-5.9.21 |
| 421 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. Group C, D.S.R.-1.8.3 |
| 422 | Wiring for light/ Power plug with 2X4 sq. mm FRLS PVC insuleted copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 Nos. 4 sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. D.S.R.-1.12 |
| 423 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 x 2.5 sq.mm. + 1 x 2.5 sq.mm. earth wire. D.S.R.-1.14.2 |
| 424 | 2 x 6 sq.mm. + 1 x 6 sq.mm. earth wire. D.S.R.-1.14.4 |
| 425 | Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. D.S.R.-1.26 |
| 426 | Supplying and fixing following modular switch / socket on existing modular plate and switch box including connections but excluding modular plate etc as required. 5/6 amps switch D.S.R.-1.24.1 |
| 427 | 15/16 amp switch D.S.R.-1.24.1 |
| 428 | 6 pin 15/16 amp socket outlet D.S.R.-1.24.1 |
| 429 | Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A \\"C\\" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioningetc. as required. D.S.R.-2.18 |
| 430 | Installation of exhaust fan in the existing opening , including making good the damage, connection, testing commissioning etc. as required. Up to 450mm sweep. D.S.R.-1.50.1 |
| 431 | Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes. D.S.R.-1.51 |
| 432 | Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required. D.S.R.-1.35 |
| 433 | Supply, Installation, Testing and Commissioning of surface LED batten 20W made of extrusion aluminum housing, LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level) >=95lumens/watt with Minimum system Lumens 2000, Life of fixture (Including Driver) : 30000 burning Hrs. @ L70B50 Lumen maintenance, CCT of 6500K (SDCM<=5) , CRI >80, PF >0.95, Min working temp range - 0°C < Ta < 45°C, an operating Voltage Range of 140 - 277 VAC.luminair manufacture shall provide LM79report from NABL accredited lab & LM80 report issued by LED manufacturer.Similar to Philips BN021C LED20S PSU CW GR S2 |
| 434 | Supply, Installation, Testing and Commissioning of 6.5W LED bulkhead made of die cast aluminum housing, LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level) >=100lumens/watt with Minimum system Lumens 700, Life of fixture (Including Driver) : 30000 burning Hrs. @ L70B50 Lumen maintenance, CCT of 4000K (SDCM<5), CRI >80, PF >0.95, Min working temp range -0°C < Ta < 45°C, an operating Voltage Range of 140 - 270 VAC.Minimum Internal Surge Protection 2.5KV & , The fixture design should comply with EMC / EMI compliance along with BIS certification for LED Driver & Luminaire ,. luminair manufacture shall provide LM79report from NABL accredited lab & LM80 report issued by LED manufacturer.Similar to Philips or equivalent. |
| 435 | Supplying and fixing Cable End Box (Loose wire box)(IP 43) suitable for following triple pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with testing and commissioning etc. as required. For 4 way, Double door TPN MCBDB. D.S.R.-2.24.1 |
| 436 | Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole, D.S.R.-2.10.1 |
| 437 | Supplying and fixing 240/415 volts, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40A 4P |
| 438 | Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. D.S.R.-2.11 |
| 439 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. D.S.R.-5.16 |
| 440 | Supply, Installation, Testing and Commissioning of 250mm size PVC exhaust fan suitable for 230V, 50 Hz AC including modifying and finishing for hole/opening for the size of fan, MS louver/ shutter complete with frame for Ex.fan including its connection with 3x1.5 sq mm FRLS copper conductor wire with PVC sleeve, loop earthing, making the good damage complete as required to do the job in all respect in accordance with laid specification or upto the satisfaction of engineer in charge. |
| 441 | SITC of H.T. VCB (11KV). 11 KV HT VCB FOUR BREAKER PANEL BOARD (INDOOR TYPE) (1 INCOMMING). Design, manufacturing, testing at works, supply of HT Panel as per specification and comprising of the following : INCOMER a) Incomming - 1 No, 630 Amp, VCB. b) 1 No.- 11 KV / 110 Volt PT class 0.5 accuracy and 100 VA burden with 1 No. voltmeter (0-12 KV), digital type, selector switch for voltmeter and protection MCB for HT Metering up to 12 KV on incommer. c) 1 No.- (0 - 120 A) dual scale Ammeter, digital type, selector switch for ammeters. d) 1 No - Microprocessor based numericak relay with O/C, E/F and S/C protection. e) 1 No - set of dual core dual ratio 3 CTs 100/5A of 15 VA burden and accuracy class 0.5 for metering and class 5P10 for protection. f) 1 No. electronic type digital energy analyser having 30 days memory and parameters of KW, KWH, Power factor, frequency etc. Suitable for BMS compatible with all accessories. g) 1 No. hooter with hooter acceptance and reset push button. h) 1 No - Red, Yellow & Blue for phase indication. i) 1 No - Amber for Trip indication. j) 1 No - Red `ON' Green `OFF'indication. k) 1 No - Spring charge indication. l) 1 No - Auto trip indication. m) 1 No. hooter with hooter acceptance and reset push button. n) 1 No. master trip relay. ( Electromechanical Type). o) 1 No.Trip ckt supervision relay. (Electromechanical Type). HT Panel switchboard complete with all interconnections, labels, wiring etc, complete as described above in item nos.A and B and as per specifications. |
| 442 | Supply and laying of 3 core standered aluminium conduktor XLPE (Cross linked polyethylene) insulated PVC bedded, Galvanised flat steel strip armoured cables confirming to I.S. 7098(Part-II with latest amendments) 11 KV grade at a depht of 900 mm below ground level over a cushion of 100 mm thick fine river sand all around and protected with well burnt bricks in sides and on the top put across. The armouring of cable shall be properly connected with earth condutor by clamps etc. 300 sq. mm 3 Core |
| 443 | Supply and making indoor cable end jointing with cast resin compound, including lugs and other jointing materials, for 3 core 300 Sq.mm. XLPE aluminium conductor cable of 11 kV grage as required. DSR 10.1.4 |
| 444 | Supply and making outdoor cable end jointing with cast resin compound, including lugs and other jointing materials, for 3 core 300 Sq.mm. XLPE aluminium conductor cable of 11 kV grage as required. DSR 10.2.4 |
| 445 | Supply and burring of Safe Earthing Electrode T-19 (Hot Dip Galvanized), Length up to 2000mm, outer pipe 50mm, inner pipe 25, terminal Dia 12 mm, outer GI pipe of 16 swg and inner GI pipe of 12 swg with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30cm square C.I. frame with hinged cover & masonry husing. |
| 446 | Suplly and burring of safe Earthing Electrode T-39 Cu Copper Coated, Length 2000mm, outer pipe 76.3mm X 3.2 inner pipe 42.4mm X 2.6mm, terminal Dia 12mm, coating 80-100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50kgs activated soil (BFC) capable of reucing the soil resistivity with good mixture of retaining capacity along with 30cm square C.I. frame withhinged cover & mansonry housing.(From electrode terminal to switch board, cost of 25x3 copper strip will be extra) Make: As approved in U.P.P.W.D & C.P.R.I. all respects. |
| 447 | Supply and laying of 50mm x 6mm G.I. strip from earth electrode directly in the ground as required complete in all respects. |
| 448 | Supply and Laying of 50mm X 6 mm Copper strip from earth electrode directly in the ground as required complete in all respects. |
| 449 | Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. D.S.R.-5.15 |
| 450 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. D.S.R.-5.16 |
| 451 | Providing and fixing MV danger notice plate of 200 mm x 150 mm made of mild steel at least 2mm thick & vitreous enamelled white on both sides and with inscription in signal red colour on front side as required. |
| 452 | Providing and fixing HT danger notice plate 250 mm x 200 mm made of mild steel at least 2mm thick & vitreous enamelled white on both sides and with inscription in signal red colour on front side as required. |
| 453 | Supplying and Fixing of Fire buckets, round bottom made of G.I. Sheet 9-11 litres capacity duly painted as per fire brigade design, supported on hanging bracket chained and locked, initially filled with fine river sand, water as per directions of Engineer-in-charge. |
| 454 | Supplying & Laying of 1800 mm x 900 mm X 12 mm thick chequered rubber matting of tested quality. |
| 455 | Supply and fixing danger board fabricated from 10 gauge MS sheet as per IE Rules |
| 456 | S/F of shock treatment chart (prescribed under I.E.rules) duly framed with glass and supported from back with hard board or soft board with supply of all material labour T & P for proper completion of work. |
| 457 | Providing & fixing in position 1000 mm wide, Electrical Insulating Mats, 2mm thick, suitable upto 1.1 KV grade including cutting to required length complete as required per specifications or upto the satisfaction of engineer-in-charge. |
| 458 | Supplying and Laying of Rubber mat 1000 mm. Wide to withstand 11 KV dielectric strength as per latest IS 15652-2006 etc. as reqd. |
| 459 | Supply of Tool & First Aid Box with all necessary tools for maintenance of electrical installation & First aid. |
| 460 | Supply & fixing of 7 mtr GI Octagonal Pole of approved make (top dia 70mm, Bottom dia 130 mm and base plate 12 mm thik) having 3mm thikness with Single arm bracket (1 Mtr length) on RCC foundation including the cost of foundation, foundation bolts, excavation & back filling and Required T&P complete in all respect. |
| 461 | Supply and fixing of LED street light fitting having die cast aluminium body and diffuser with driver set suitable for 45 watt to 50 watt. Confirming to IP 66 and above protection complete in all respect. |
| 462 | Supply and fixing of 20 Amp DP MCB (10KA) (C curve) for poles |
| 463 | Supply and fixing of Bakelite sheet 3 mm thick of suitable size & connector |
| 464 | Supply and fixing of decorative 8 to 16 Watt LED bollard luminaire with driver set confirming to IP 65 protection complete in all respect. |
| 465 | Supplying following 1.1kV grade, heavy duty XLPE insulated, FRLS type armoured /Unarmured cables suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath, outer sheath provided with FRLS insulation, galvanised steel armouring (round or flat as mentioned) and with all components as mentioned in BOQ, specifications and schedule, complete as required. 3.5C x 300 sqmm aluminium conductor, A2XWY. |
| 466 | 3.5C x 240 sqmm aluminium conductor, A2XWY. |
| 467 | 3.5C x 150 sqmm aluminium conductor, A2XWY. |
| 468 | 3.5C x 120 sqmm aluminium conductor, A2XWY. |
| 469 | 3.5C x 95 sqmm aluminium conductor, A2XWY. |
| 470 | 3.5C x 70 sqmm aluminium conductor, A2XWY. |
| 471 | 3.5C x 50 sqmm aluminium conductor, A2XWY. |
| 472 | 3.5C x 35 sqmm aluminium conductor, A2XWY. |
| 473 | 3.5C x 25 sqmm aluminium conductor, A2XWY. |
| 474 | 4C x 16 sqmm aluminium conductor, 2XWY. |
| 475 | 4C x 10 sqmm aluminium conductor, 2XWY. |
| 476 | 2C x 16 sqmm aluminium conductor, 2XWY. |
| 477 | 2C x 10 sqmm aluminium conductor, A2XWY. |
| 478 | 2C x 6 sqmm aluminium conductor, A2XWY. |
| 479 | Supplying following 1.1kV grade, XLPE insulated, FRLS type control cables,suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath, outer sheath provided with FRLS insulation and with all components as mentioned in BOQ, specifications and schedule, complete as required. 2C X 2.5 sqmm copper conductor |
| 480 | 4C X 2.5 sqmm copper conductor |
| 481 | 6C X 2.5 sqmm copper conductor |
| 482 | Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Upto 35 sq. mm (clamped with 1mm thick saddle), D.S.R.-7.8.1 |
| 483 | Above 35 sq. mm and upto 95 sq. mm (clamped with 1mm thick saddle), D.S.R.-7.8.2 |
| 484 | Above 95 sq. mm and upto 185 sq. mm (clamped with 1mm thick saddle), D.S.R.-7.8.3 |
| 485 | Above 185 sq. mm and upto 400 sq. mm (clamped with 1mm thick saddle), D.S.R.-7.8.4 |
| 486 | Supplying and making end termination with brass compression gland and copper lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 3½ X 300 sq. mm (70 mm), D.S.R.-9.1.30 |
| 487 | 3½ X 240 sq. mm (62mm), D.S.R.-9.1.29 |
| 488 | 3½ X 185 sq. mm (57mm), D.S.R.-9.1.27 |
| 489 | 3½ X 150 sq. mm (50 mm), D.S.R.-9.1.26 |
| 490 | 3½ X 120 sq. mm (50 mm), D.S.R.-9.1.25 |
| 491 | 3½ X 95 sq. mm (45 mm), D.S.R.-9.1.24 |
| 492 | 3½ X 70 sq. mm (38mm), D.S.R.-9.1.23 |
| 493 | 3½ X 50 sq. mm (32mm), D.S.R.-9.1.22 |
| 494 | 3½ X 35 sq. mm (32mm), D.S.R.-9.1.20 |
| 495 | 3½ X 25 sq. mm (28mm), D.S.R.-9.1.21 |
| 496 | 4 X 16 sq. mm (28mm), D.S.R.-9.1.33 |
| 497 | 4 X 10 sq. mm (25mm), D.S.R.-9.1.32 |
| 498 | 2 X 16 sq. mm (22mm), D.S.R.-9.1.3 |
| 499 | 2 X 10 sq. mm (19mm), D.S.R.-9.1.2 |
| 500 | 2 X 6 sq. mm (19mm), D.S.R.-9.1.1 |
| 501 | 2C X 2.5 sqmm copper conductor (19mm) |
| 502 | 4C X 2.5 sqmm copper conductor (19mm) |
| 503 | 6C X 2.5 sqmm copper conductor (19mm) |
| 504 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 90 mm dia (OD-90 mm & ID-76 mm nominal). DSR 14.16.2 |
| 505 | 120 mm dia (OD-120 mm & ID-103 mm nominal). DSR 14.16.3 |
| 506 | 160 mm dia (OD-200 mm & ID-175 mm nominal). DSR 14.16.4 |
| 507 | 200 mm dia (OD-200 mm & ID-175 mm nominal). DSR 14.16.5 |
| 508 | Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required. 100 mm dia. DSR 14.14.1 |
| 509 | 150 mm dia. DSR 14.14.2 |
| 510 | 250 mm dia. DSR 14.14.3 |
| 511 | 300 mm dia. DSR 14.14.4 |
| 512 | Making of following size of Cable Chamber made of 230 mm thick brick work in cement mortar (1 cement : 6 sand) with PCC 100 mm thick PCC base plastering of inner and outer surface with cement mortar including providing of Heavy Duty C.I Cover complete with digging, refilling and removal of surplus soil complete as required. 900 mm x 800 mm x 1000 mm deep |
| 513 | 600 mm x 600 mm x 800 mm deep |
| 514 | SITC OF MAIN PANEL FEEDER PILLAR: Design, Supply, installation, testing and commissioning of indoor/outdoor floor mounted/ wall mounted, IP43/IP65, IEC 61439/IS 8623, factory built, modular, sectionalised, compartmentalized, extendable type HT/LT cubicle panel of suitable size suitable for operation on 33/11/0.433/0.415 kV, 50 Hz AC 3 phase supply system fabricated from CRCA sheet steel of 2mm thick for frame work and covers, 3mm thick for gland plates with stiffeners wherever required, having vibration free structure chemically treated with seven tank process or better before painting for surface treatment and powder coated in approved shade, with suitable electrolytic grade high conductivity bus bars extensible, DMC/ SMC (whichever is superior) bus bar supports, with short circuit withstand capacity as mentioned ,bottom base channel of section not less than 100mmX 50mmX 5 mm thick, fabrication shall be done in transportable sections, entire panel shall have a common earth bar of required size at the rear with 2 Nos. earth stud, connections and interconnection with solid conductor wires / copper strips, neutral links, control wiring with 1.5 sqmm. & 2.5sqmm. PVC insulated FRLS copper conductor S/C cable for voltage & current respectively, including providing and fixing following switch gears as per SLD ,technical specifications etc.complete in all respect so as to fulfill all as required. LT Panel The minimum clearances between bus bars shall be as follows : Phase to phase - minimum 20mm. Phase to neutral-minimum 15mm. Incoming: 2Nos 1000 Amp. 4P ACB of 50kA EDO Breaking capacity. Metering: 2 Set of CT's one of 1000/ 5Amp ratio for Multifunction Meter. 1 Set of CT's one of 1000/ 5Amp ratio for AFCR Relay. 2 Set of CT's one of 1000/ 5Amp ratio for 50,50N,51,51N Relay. 2 Nos. Set of Phase Indication Lamp. 2 Nos. of class-III Type SPD. Bus Bar: 1500 Amp.TPN aluminimum bus bar of suitable length.36KA. Outgoing: Phase indication lamps on each outgoing to be provided. 05 No. 400 Amp 4P MCCB. (36 KA). 01 No. 100 Amp 4P MCCB. (25 KA). 05 No. 63 Amp 4P MCCB. (25 KA). Panel described as above |
| 515 | CAPACITOR PANEL-180 KVAR: SITC APFC Panel of 180 KVAR capacity suitable for operation on 415 + 5% Volt, 3 Phase, 50Hz, AC supply, having MPP type, resin bounded, static 10,15,25 KVAR capacitors (without oil) in tier formation complete with following TPN MCCB as incomer of the panel, 7 step microprocessor based power factor controller relay capable to select the rating from 1 KVAR to multiples thereon up to max rating of the panel, current limiting contactors for each capacitors protected with MCBs, Ammeter (Analogue type) with CTs, Voltmeter (Analogue type) selector switches indicating lights, cooling fans for panel, earthing the panel with 2 Nos. 25mm x 5mm thick GI steel flat from existing earth bar, connection of APFC panel with suitable size 3.5 core aluminium conductor armoured XLPE cable from main LT panel (maximum length of cable 10 mtrs.) and compression glands etc. as reqd. The panel should have provision of timer based circuit in APFC relay to switch ON and OFF the static part automatically as and when requried. Capacity of Static capacitors should be accommodated from the overall rating of the panel and should be designed to switch in independently. The panel should be manufactured with 1.6mm thick CRCA sheet duly powder coated. Incoming: One (1) No 250 Amp. 3P MCCB of 36 KA Breaking capacity, 1 Set of CT's one of 250/ 5Amp ratio for Multifunction Meter, 1 Set of CT's one of 250/ 5Amp ratio 55, 1 Nos. Set of Phase Indication Lamp. BUS BAR: 1 Set of 300 Amps TP Aluminium Bus Bars. OUT GOING: 04 No. 63 Amps. TP MCCB (25 KA), 04 No. 40 Amps. TP MCCB (25 KA), 02 No. 25 Amps. TP MCCB (25 KA), 04 No. 25 KVAR Capacitor Bank, 04 No. 15 KVAR Capacitor Bank, 02 No. 10 KVAR Capacitor Bank, 04 No. 25 KVAR 7% Duty Reactor, 04 No. 15 KVAR 7% Duty Reactor, 02 No. 10 KVAR 7% Duty Reactor, 04 No. 25 KVAR TSM, 04 No. 15 KVAR TSM, 02 No. 10 KVAR TSM, Panel described as above |
| 516 | SFP Outdoor Type(IP 65) -1/2: Incoming : 1 Nos. 40 Amp. 4P MCCB of 25KA Breaking capacity. Metering: Multifunction Meter, One (1) Set of Phase Indication Lamp. Bus Bar : One (1) No. 100 Amp.TPN aluminimum bus bar of suitable length. Outgoing : Phase indication lamps on each outgoing to be provided. 6 No.20 Amp DP MCB. (10 KA). 4 Nos. 1 Phase Timer. Panel described as above |
| 517 | SITC 630 KVA RADIATOR COOLED D.G. SET IN ACOUSTIC ENCLOSURE WITH AMF OR Equivalent & Exhaust System with complete Accessories. Providing, installation testing & commissioning of 'Silent Type' Diesel Generating Set along with having prime power rating 630 KVA, 415 Volts at 1500RPM, 0.8 lagging Factor at 415 V suitable for 50 Hz, 3 phase system and for 0.85 load factor and consisting of the following:- Diesel Engine: Diesel Engine 4 stroke radiator cooled, electric start, of suitable bhp (CPCB-2 Compliance) having Six cylinders at 1500 RPM suitable for above output of alternator , 50% RH & at 1000 metre MSL and confirming to BS 5514, BS 649, is 10000, capable of taking 10% overloading for one hour after 12 hours of continuous operation. The engine will be fitted complete with all the required accessories. The DG Set Controller shall be supplied by the same vendor of DG Set OEM. Engine Mounted Instrument Panel fitted with and having digital display for following: Start- stop switch with key. Water Temperature indication. Lubrication Oil pressure indication. Battery charging indication. RPM indication. Over Speed trip Indication. Low lubrication oil Pressure trip indication. Engine Hours Indication. Alternator: Synchronous alternator rated at 630 KVA, 415 Volts at 1500 RPM, 3 phase 50 Hz, AC Supply with 0.8 lagging power factor , 50% RH . The alternator shall be having SPDB enclosure, brushless, continuous duty, self-excited and self-regulated through AVR confirming to IS:4722/ BS 2613 suitable for tropical conditions and with class- H insulation. Alternator shall have end termination cable box on alternator to terminate the 800A Bus Duct. Base Frame & Foundation: Both the engine and alternator shall be mounted on suitable base frame made of MS channel with necessary reinforcement which shall be installed on suitable cement concrete foundation and vibration isolation arrangement as per recommendations of manufacturer. Fuel Tank: Daily service fuel tank of 990 litres capacity, fabricated out of 3mm thick M.S. sheet complete with all standard accessories and fuel piping between fuel tank and diesel engine with MS class 'C pipes of suitable dia. Complete with valves level indication & accessories as required as per specifications. Exhaust System : Dry exhaust mainfold with hospital grade exhaust silencer / Catalytic Convertor. Starting System: 24V DC starting system comprising of starter motors: voltage regulator and arrangement for initial excitation complete with 2 Nos. of batteries (25 plates, 160 AH lead Acid type) as required as per specifications. Accoustic and weather proof enclosure with arrangement for fresh air intake for cooling of the engine & alternator, extraction, discharging hot air into the atmosphere as per specifications. The Acoustic Enclosure shall be factory fitted by the OEM. Note:Foundation work for DG SETs is not included in Electrical works it will come on Civil work. |
| 518 | TRANSFORMER: SITC of 630KVA 11KV/433V Dyn11 Copper Wound Oil Type Transformer with OCTC +5% to -10% in steps of 2.5% , Class of Insulation: A, Temperature rise limits of 40 deg.C over ambient of 50 degrees. Losses (As per IS tolerances) and all accessories and confirming to As per IS 1180 Level 1 & Testing parameter as per IS 2026 complete with all fittings and accessories as per specifications attached etc as required at site. (Note:Foundation work for transformer is not included in Electrical works it will come on Civil work.) |
| 519 | Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level. 400 mm dia, D.S.R.-23.1.1.3 |
| 520 | Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. 400 mm dia, D.S.R.-23.1.1.3 |
| 521 | Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 mild steel screwed and socketed/plain ended casing pipes of required dia, conforming to IS: 4270, of reputed & approved make, including painted with outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer-in-charge. 200 mm nominal size dia having minimum wall thickness 5.40 mm, D.S.R.-23.10.3 |
| 522 | Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 plain slotted (having slot of size 1.6/3.2 mm) mild steel threaded and socketed/ plain bevel ended pipe (type A) of required dia, conforming to IS: 8110, of reputed and approved make, having wall thickness not less than 5.40 mm, including painted with outside surface with two coats of anticorrosive bitumestic paint of approved brand and manufacture, including hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia, D.S.R.-23.11.3 |
| 523 | Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. D.S.R.-23.8 |
| 524 | Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by \\"V\\" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. D.S.R.-23.12 |
| 525 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia, D.S.R.-23.13.3 |
| 526 | Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp. D.S.R.-23.14.3 |
| 527 | Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 200 mm dia. D.S.R.-23.15.3 |
| 528 | Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 65 mm dia nominal bore, D.S.R.-18.12.7 |
| 529 | Sypply and Installation of 350-400 LPM Submersible Pump Set of 15 H.P. capacity, K.S.B. Make including Starter panel, support wire, A. Meter etc. complete. |
| 530 | Supply and fixing of nylon jali around the slotted pipes complete as required. up to 10 meter |
| 531 | Sypply and laying of alluminium conductor pvc insulated armoured served sheathed cables 1100 volts grade at a depth of 750 mm below ground level over a cushion of 75 mm thick sand all around and protected with burnt brick on sides and on top. On surface the cable run shall be fixed on m.s clamps etc. of suitable size or as directed by the Engineer in charge , complete in all respect . the armouring of the cable shall be properly connected with the earth conductor by clamps etc. 35 SQ.MM 3-1/2 core |
| 532 | Water testing chemical and bactriological |
| 533 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. D.S.R.-2.8.1 |
| 534 | Excavating, supplying, stacking and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift. D.S.R.-2.25A |
| 535 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. D.S.R.-2.27 |
| 536 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources), D.S.R.-4.1.8 |
| 537 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) (Plinth Beam), D.S.R.-5.1.2 |
| 538 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). D.S.R.-5.3 |
| 539 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). Slabs, D.S.R.-5.3 |
| 540 | Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform, D.S.R.-5.9.3 |
| 541 | Lintels, beams, plinth beams, girders, bressumers and cantilevers, D.S.R.-5.9.5 |
| 542 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand), D.S.R.-6.1.2 |
| 543 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 ( 1 cement : 6 coarse sand), D.S.R.-6.4.2 |
| 544 | Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources), D.S.R.-4.10 |
| 545 | Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. D.S.R.-4.13 |
| 546 | Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration, D.S.R.-2.35.3.1 |
| 547 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level & above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. D.S.R.-5.22.6 &5.22A.6 |
| 548 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete size 250x16 mm, D.S.R.-9.62.2 |
| 549 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 250x10 mm, D.S.R.-9.63.1 |
| 550 | 150x10 mm, D.S.R.-9.63.3 |
| 551 | Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :125 mm, D.S.R.-9.66.1 |
| 552 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws (Single leaf). D.S.R.-9.21.1 |
| 553 | Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). D.S.R.-9.23 |
| 554 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). D.S.R.-10.13.1 |
| 555 | Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), D.S.R.-10.11.1 |
| 556 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with 4.0 mm thick glass panes, D.S.R.-10.30.1 |
| 557 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works, D.S.R.-10.25.2 |
| 558 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm. D.S.R.-22.7.1 |
| 559 | 12 mm cement plaster on fair side of single or half brick wall of mix 1:6 (1 cement: 6 coarse sand), D.S.R.-13.4.2 |
| 560 | 15 mm cement plaster on rough side of single or half brick wall of mix 1:6 (1 cement: 6 coarse sand), D.S.R.-13.5.2 |
| 561 | 15 mm cement plaster in single coat on plinth 1 cement: 4 course sand in plinth. D.S.R.-13.5.1 |
| 562 | Add for plaster groove in plastered surface or moulding to R.C.C. projections. D.S.R.-5.30 |
| 563 | Add for plaster drip course in plastered surface or moulding to R.C.C. projections. PWD-13.20 |
| 564 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate, D.S.R.-11.3.1 |
| 565 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre, D.S.R.-13.41.1 |
| 566 | Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm), D.S.R.-13.44.1 |
| 567 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture, D.S.R.-13.48.3 |
| 568 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture, D.S.R.-13.48.2 |
| 569 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. D.S.R.-12.22 |
| 570 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter, D.S.R.-12.41.2 |
| 571 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Coupler 110 mm, D.S.R.-12.42.1.2 |
| 572 | Bend 87.5°, 110 mm bend, D.S.R.-12.42.5.2 |
| 573 | Shoe (Plain), 110 mm Shoe, D.S.R.-12.42.6.2 |
| 574 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm, D.S.R.-12.42.1.2 |
| 575 | Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. D.S.R.-12.44 |
| 576 | Internal Electrification Pump Room |
| 577 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil. In all kind of soil, D.S.R.-2.8.1 |
| 578 | Extra additional lift above 1.5 m, D.S.R.-2.26.1 |
| 579 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources), D.S.R.-4.1.8 |
| 580 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand), D.S.R.-6.1.2 |
| 581 | Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 20 mm cement plaster. D.S.R.-13.9.2 |
| 582 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate, D.S.R.-11.3.1 |
| 583 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete.Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. Concrete of M25 grade with minimum cement content of 330 kg /cum All works upto plinth level, D.S.R.-5.33.1.1 |
| 584 | Add for using extra cement in the items of design mix over and above the specified cement content therein. D.S.R.-5.35 |
| 585 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level & above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. D.S.R.-5.22.6 & 5.22A.6 |
| 586 | Providing M.S. foot rest including fixing with 20x20x10 cm. cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 gradded aggregate of nominal size 20mm ) as per standard design with 20x20mm sq bars. D.S.R.-19.15.1 |
| 587 | Providing and fixing 150 mm S.C.I. tee at the inlet and outlet of septic tank. D.S.R.-7087 |
| 588 | Providing & fixing 75mm dia vent pipes. D.S.R.-17.35.2.2 |
| 589 | Providing & fixing of 75mm dia cast iron terminal guard. D.S.R.-17.56.2.2 |
| 590 | Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality. M.D. -10- Circular shape 500mm internal diameter, D.S.R.-19.19.2.2 |
| 591 | L.D. -2.5- Circular shape 450mm internal diameter, D.S.R.-19.19.1.3 |
| 592 | SOAK PIT (2500 MM DIA & 3000 MM DEPTH) |
| 593 | LIFTS (8 PASSENGER LIFT) |
| 594 | TICKETING & POS SYSTEM |
| 595 | Supply, Installation, Testing & Commissioning (SITC) of Sympathetic Swing - X complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 596 | Supply, Installation, Testing & Commissioning (SITC) of Sympathetic Swing - Y complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 597 | Supply, Installation, Testing & Commissioning (SITC) of Sympathetic Swing - Z complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 598 | Supply, Installation, Testing & Commissioning (SITC) of Transfer of Momentum (7-ball system) complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 599 | Supply, Installation, Testing & Commissioning (SITC) of Vortex (Large) complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 600 | Supply, Installation, Testing & Commissioning (SITC) of Floating Ball (Bernoulli) complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 601 | Supply, Installation, Testing & Commissioning (SITC) of Lazy Coin (Eddy current) complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 602 | Supply, Installation, Testing & Commissioning (SITC) of Seebeck Siren complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 603 | Supply, Installation, Testing & Commissioning (SITC) of Lines of Force complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 604 | Supply, Installation, Testing & Commissioning (SITC) of Identify a Magnet complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 605 | Supply, Installation, Testing & Commissioning (SITC) of Infinity well complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 606 | Supply, Installation, Testing & Commissioning (SITC) of Illusion with Rings complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 607 | Supply, Installation, Testing & Commissioning (SITC) of Moiré Patterns complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 608 | Supply, Installation, Testing & Commissioning (SITC) of Changing Colours complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 609 | Supply, Installation, Testing & Commissioning (SITC) of Colour Pyramid complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 610 | Supply, Installation, Testing & Commissioning (SITC) of Colour Shadows complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 611 | Supply, Installation, Testing & Commissioning (SITC) of Turning Mask complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 612 | Supply, Installation, Testing & Commissioning (SITC) of Curie Point complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 613 | Supply, Installation, Testing & Commissioning (SITC) of Distorted Mirrors (4 nos) complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 614 | Supply, Installation, Testing & Commissioning (SITC) of Float in Air (Perpendicular Mirrors) complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 615 | Supply, Installation, Testing & Commissioning (SITC) of Light Corridor (Parallel Mirrors) complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 616 | Supply, Installation, Testing & Commissioning (SITC) of Kaleidoscope complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 617 | Supply, Installation, Testing & Commissioning (SITC) of Rotate Your Face complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 618 | Supply, Installation, Testing & Commissioning (SITC) of Head on the Platter complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 619 | Supply, Installation, Testing & Commissioning (SITC) of Complete Mirror Maze (excluding above) complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 620 | Supply, Installation, Testing & Commissioning (SITC) of PIN Art and other small hands-on exhibits complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 621 | Supply, Installation, Testing & Commissioning (SITC) of Activity Desks and Puzzles complete including structure, casing, mechanism, electricals, internal lighting (if any), graphics, anchoring, safety guards, wiring, documentation & O&M manuals as per DPR/specifications. |
| 622 | SITC of Theming walls + feature elements: ACP/PVC + paint system, child-safe corner guards including all materials, fasteners, supports, finishing, anchoring/patch works, testing, commissioning and making good complete. |
| 623 | SITC of Interpretive + wayfinding graphics: Bilingual (Hindi+English), anti-scratch laminate, replaceable panels including all materials, fasteners, supports, finishing, anchoring/patch works, testing, commissioning and making good complete. |
| 624 | SITC of Internal gallery lighting (in scope): Track/linear LEDs, accent lighting to optics & maze, drivers, conduits including all materials, fasteners, supports, finishing, anchoring/patch works, testing, commissioning and making good complete. |
| 625 | SITC of Staff console + storage: Counter + lockable storage + cable management including all materials, fasteners, supports, finishing, anchoring/patch works, testing, commissioning and making good complete. |
| 626 | SITC of Octonorm cases + wooden stands/cabinets: Display cases + storage; HPL laminate; locks; LED including all materials, fasteners, supports, finishing, anchoring/patch works, testing, commissioning and making good complete. |
| 627 | SITC of Installation, testing, documentation, O&M manuals: Site works, FAT/SAT, training, manuals including all materials, fasteners, supports, finishing, anchoring/patch works, testing, commissioning and making good complete. |
| 628 | SITC of Contingency/spares buffer (capex controlled): Minor escalation, spares starter kit, patches including all materials, fasteners, supports, finishing, anchoring/patch works, testing, commissioning and making good complete. |
| 629 | SITC of Sushruta – The Dawn of Surgery complete with MS frame, FR plywood cladding, diorama/model fabrication with FRP figures/props as per approved drawings, matte anti-glare finishes, bilingual graphics/panels, in-built LED lighting with drivers, required AV/IT components (if any), concealed wiring in conduits, lockable service access, floor anchoring with chemical fasteners, testing & commissioning, complete in all respects. |
| 630 | SITC of Charak – The Ecosystem of Wellness complete with MS frame, FR plywood cladding, diorama/model fabrication with FRP figures/props as per approved drawings, matte anti-glare finishes, bilingual graphics/panels, in-built LED lighting with drivers, required AV/IT components (if any), concealed wiring in conduits, lockable service access, floor anchoring with chemical fasteners, testing & commissioning, complete in all respects. |
| 631 | SITC of Patanjali – Mapping the Inner World complete with MS frame, FR plywood cladding, diorama/model fabrication with FRP figures/props as per approved drawings, matte anti-glare finishes, bilingual graphics/panels, in-built LED lighting with drivers, required AV/IT components (if any), concealed wiring in conduits, lockable service access, floor anchoring with chemical fasteners, testing & commissioning, complete in all respects. |
| 632 | SITC of Nagarjuna – The Alchemical Laboratory (Rasashala) complete with MS frame, FR plywood cladding, diorama/model fabrication with FRP figures/props as per approved drawings, matte anti-glare finishes, bilingual graphics/panels, in-built LED lighting with drivers, required AV/IT components (if any), concealed wiring in conduits, lockable service access, floor anchoring with chemical fasteners, testing & commissioning, complete in all respects. |
| 633 | SITC of Copper Smelting – The Birth of the Metal Age complete with MS frame, FR plywood cladding, diorama/model fabrication with FRP figures/props as per approved drawings, matte anti-glare finishes, bilingual graphics/panels, in-built LED lighting with drivers, required AV/IT components (if any), concealed wiring in conduits, lockable service access, floor anchoring with chemical fasteners, testing & commissioning, complete in all respects. |
| 634 | SITC of Ship Building – Masters of the Monsoon Winds complete with MS frame, FR plywood cladding, diorama/model fabrication with FRP figures/props as per approved drawings, matte anti-glare finishes, bilingual graphics/panels, in-built LED lighting with drivers, required AV/IT components (if any), concealed wiring in conduits, lockable service access, floor anchoring with chemical fasteners, testing & commissioning, complete in all respects. |
| 635 | SITC of Harappan/Mohenjo-daro Civil City + Water Management (Combined) complete with MS frame, FR plywood cladding, diorama/model fabrication with FRP figures/props as per approved drawings, matte anti-glare finishes, bilingual graphics/panels, in-built LED lighting with drivers, required AV/IT components (if any), concealed wiring in conduits, lockable service access, floor anchoring with chemical fasteners, testing & commissioning, complete in all respects. |
| 636 | SITC of Ancient Town/Market + Stepwell (Vav) Water Management complete with MS frame, FR plywood cladding, diorama/model fabrication with FRP figures/props as per approved drawings, matte anti-glare finishes, bilingual graphics/panels, in-built LED lighting with drivers, required AV/IT components (if any), concealed wiring in conduits, lockable service access, floor anchoring with chemical fasteners, testing & commissioning, complete in all respects. |
| 637 | SITC of Sulbasutras – Geometry of the Sacred (Śyenaciti) complete with MS frame, FR plywood cladding, diorama/model fabrication with FRP figures/props as per approved drawings, matte anti-glare finishes, bilingual graphics/panels, in-built LED lighting with drivers, required AV/IT components (if any), concealed wiring in conduits, lockable service access, floor anchoring with chemical fasteners, testing & commissioning, complete in all respects. |
| 638 | SITC of Aryabhata & Brahmagupta – Charting the Heavens complete with MS frame, FR plywood cladding, diorama/model fabrication with FRP figures/props as per approved drawings, matte anti-glare finishes, bilingual graphics/panels, in-built LED lighting with drivers, required AV/IT components (if any), concealed wiring in conduits, lockable service access, floor anchoring with chemical fasteners, testing & commissioning, complete in all respects. |
| 639 | SITC of Jantar Mantar – The Monument of Calculation complete with MS frame, FR plywood cladding, diorama/model fabrication with FRP figures/props as per approved drawings, matte anti-glare finishes, bilingual graphics/panels, in-built LED lighting with drivers, required AV/IT components (if any), concealed wiring in conduits, lockable service access, floor anchoring with chemical fasteners, testing & commissioning, complete in all respects. |
| 640 | SITC of Touchscreen Kiosk – The Digital Sutra complete with MS frame, FR plywood cladding, diorama/model fabrication with FRP figures/props as per approved drawings, matte anti-glare finishes, bilingual graphics/panels, in-built LED lighting with drivers, required AV/IT components (if any), concealed wiring in conduits, lockable service access, floor anchoring with chemical fasteners, testing & commissioning, complete in all respects. |
| 641 | SITC of Amphitheatre/Quiz Arena – The Jijnasa Arena complete with MS frame, FR plywood cladding, diorama/model fabrication with FRP figures/props as per approved drawings, matte anti-glare finishes, bilingual graphics/panels, in-built LED lighting with drivers, required AV/IT components (if any), concealed wiring in conduits, lockable service access, floor anchoring with chemical fasteners, testing & commissioning, complete in all respects. |
| 642 | SITC of complete gallery decor & fit-out including modular partitions, flooring & skirting, zone gateways, signage & wayfinding, benches, cabinetry/storage, AV rack infra, and allied works complete (excluding civil/MEP shell), as per drawings and specifications. |
| 643 | SITC of software/content development for Touchscreen Kiosk + Quiz Arena including interactive modules, animations, bilingual UI/copy, QA testing, deployment, and handover of source/installer, complete. |
| 644 | Comprehensive Maintenance (CMC) for 1 years for all exhibits, AV/IT systems, and decor including preventive maintenance, breakdown support, spares as specified, quarterly visits, and documentation, complete. |
| 645 | Transportation, packing/crating, loading/unloading, insurance and handling for exhibits and decor up to site, complete. |
| 646 | Site supervision, coordination, final integration, training & handover documentation for the complete gallery, complete. |
| 647 | Design, supplying, fabricating, transporting, installing, testing & commissioning of curved projection wall system (approx. 8.0m×3.5m) with POP projection-grade finish on engineered substrate, including MS framework/anchoring, access panels, complete AV system comprising 2 Nos. 10,000-lumen (or higher) laser projectors with edge blending, media server, 5.1 audio with amplifiers/speakers, control wiring, conduits, earthing, protection, alignment/calibration, content loading, training, documentation and handover, complete as per drawings/specifications and direction of Engineer-in-Charge. |
| 648 | Design, supply, fabrication, installation, testing & commissioning of interactive Tectonic Puzzle exhibit comprising backlit acrylic world map (approx. 4.0m×2.5m) with magnetic continent pieces, sensor system (Hall sensors/encoders as required) with controller, 65-inch commercial vertical touchscreen kiosk with stand/cabinet, bilingual interactive content/software with kiosk lockdown, complete with all wiring, SMPS/UPS as required, mounting hardware, signages, testing, training, documentation and handover, complete as per direction of Engineer-in-Charge. |
| 649 | Design, supply, installation, testing & commissioning of Earthquake Simulator platform (approx. 2.5m×2.0m) with multi-axis actuation system, PLC/drive controls, safety railings (SS304) and guarding (toughened/laminated glass as specified), 75-inch 4K display with synchronized AV content, emergency stop, interlocks, vibration isolators, complete with all electricals, control panel, cabling, earthing, safety compliance, trial runs, training, documentation and handover, complete as per direction of Engineer-in-Charge. |
| 650 | Design, supplying, installation, testing & commissioning of AR Volcano exhibit comprising FRP volcano model (approx. Ø2.0m×1.5m) with texture/paint finish, 4 Nos. rugged tablets with secure mounts/charging, AR application (Unity/Unreal or equivalent) with bilingual UI, exhibit lighting suitable for tracking, networking/charging accessories, complete with commissioning, training, documentation and handover, complete as per direction of Engineer-in-Charge. |
| 651 | Providing & fixing Deccan Traps basalt themed feature wall (approx. 6.0m×3.5m) with MS sub-frame, GFRC relief/topo finish and natural basalt touch band, including 3 Nos. dust-sealed high-security specimen display cases with low-iron AR glass, locks and LED/fiber-optic lighting, backlit SEG graphic panel, all supports/fasteners, finishing, testing and handing over, complete as per direction of Engineer-in-Charge. |
| 652 | Design, supply, installation, testing & commissioning of Digital Rock Cycle Wall exhibit comprising central plinth (approx. Ø1.8m) with 3 Nos. rock specimens and sensors, 3 Nos. 55-inch commercial vertical touch displays, RTX-class PC/workstation, control/interface electronics, interactive bilingual software, complete with all mounting, cabling, earthing, calibration, documentation, training and handover, complete as per direction of Engineer-in-Charge. |
| 653 | Design, supply, fabrication, installation, testing & commissioning of Immersive Crystal Cave (approx. 6.0m×4.0m) comprising MS framework, GFRC/resin crystal panels, DMX controlled architectural lighting, audio soundscape system, 3 Nos. secure display cases, electrical wiring/control gear, safety provisions, finishing, trial runs, documentation, training and handover, complete as per direction of Engineer-in-Charge. |
| 654 | Supply & installation of Mineral Fluorescence high-security display case (approx. 2.0m wide) with UV-blocking laminated/AR glass, dual lighting system (white + UV) with push-button/relay controls, ventilation provisions, locks/interlocks for UV safety, internal mounts for specimens, complete with wiring, testing, commissioning, training and handover, complete as per direction of Engineer-in-Charge. |
| 655 | Design, supply, installation, testing & commissioning of Interactive Stream Table (approx. 3.0m×1.5m) with waterproof basin, erosion media, closed-loop pump/filter/reservoir plumbing, overhead 4K camera system, 65-inch 4K monitor, control electronics, required valves/fittings, splash protection, complete with commissioning, testing, training, documentation and handover, complete as per direction of Engineer-in-Charge. |
| 656 | Design, supply, installation, testing & commissioning of Interactive Geo-heritage Floor Map system comprising walkable projection surface (approx. 5.0m×3.5m) with durable epoxy/PU finish, ceiling short-throw projector(s), visitor tracking system (CV/sensors), 3×3 video wall (9 Nos. 55-inch commercial panels) with mounts/controllers, synchronization software, media server, complete cabling, earthing, calibration, trials, training, documentation and handover, complete as per direction of Engineer-in-Charge. |
| 657 | Providing, supplying & fixing high-security museum display case (approx. 0.7m×0.7m×1.8m) with UV-filter low-iron AR laminated glass, locks, alarm sensors, fiber-optic/LED lighting, humidity control provisions, internal mounts and replica egg, complete with testing, commissioning and handover, complete as per direction of Engineer-in-Charge. |
| 658 | Providing & fixing serpentine/curved partitions comprising MS stud framing, plywood backing/FR gypsum boards, acoustic infill, access panels, required stiffeners, primer/putty and paint/texture finish, including all hardware, scaffolding, cutting/openings for services, alignment, cleaning and finishing, complete as per drawings and direction of Engineer-in-Charge. |
| 659 | Providing & fixing themed feature wall finishes including strata/topographic textures, GFRC/relief panels, printed/painted backdrops, MS sub-frames, surface preparation, primer/putty/paint, protective coating, complete with fixing accessories and finishing, complete as per direction of Engineer-in-Charge. |
| 660 | Supply, installation, testing & commissioning of exhibit track lighting system including tracks, fixtures (LED), drivers, dimming/control as required, aiming/focusing, wiring, conduits, mounting hardware and accessories, complete as per lighting layout and direction of Engineer-in-Charge. |
| 661 | Providing exhibit-required floor finishes including anti-slip coatings at wet/interactive nodes, tactile strips as specified, surface preparation, primers, application, curing, cleaning and protection, complete as per direction of Engineer-in-Charge. |
| 662 | Supply & fixing lockable dust-sealed specimen display cases with low-iron AR glass including internal mounts, LED/fiber lighting, locks, hinges, ventilation as required, all fixing hardware, testing and handing over, complete as per direction of Engineer-in-Charge. |
| 663 | Providing & fixing integrated benches/pause points comprising MS/ply structure, top finish (laminate/solid surface as specified), edge bands, anchoring to floor/wall, complete with finishing, complete as per direction of Engineer-in-Charge. |
| 664 | Supply, installation, testing & commissioning of central AV/IT rack system comprising 42U rack with accessories, 6 kVA online UPS, PDUs, rack ventilation, patch panels, cable managers, earthing, labeling and commissioning, complete as per direction of Engineer-in-Charge. |
| 665 | Supplying, installing, testing & commissioning of managed PoE network switches, router, Wi‑Fi 6 access points, structured cabling (Cat‑6A) with patch cords/faceplates/patch panels, conduits/trays as required, testing (Fluke or equivalent) and labeling, complete as per direction of Engineer-in-Charge. |
| 666 | Designing, developing, testing, deploying and commissioning bilingual interactive software including synchronization, logging/analytics, kiosk lockdown, remote monitoring, CMS for content updates, licenses, source/configuration handover, user manuals and training, complete as per direction of Engineer-in-Charge. |
| 667 | Designing, printing, supplying & fixing bilingual graphics including zone headers, interpretive panels, safety signages, wayfinding, substrates (ACP/foamboard/acrylic/vinyl as specified), lamination/protection, installation with hardware, complete as per direction of Engineer-in-Charge. |
| 668 | Providing complete installation labour with tools & tackles for exhibit installation, alignment, calibration, FAT/SAT support, testing & commissioning assistance, training, O&M manuals, as-built documentation and handover, complete as per direction of Engineer-in-Charge. |
| 669 | SITC of interactive museum exhibit “The Primordial Soup” for Zone-1, including detailed design/engineering, complete fabrication (MS structure with premium finish; FR/ply/FRP/acrylic/polycarbonate as required), thematic models/props, high-resolution printed graphics with protective laminate, all interactive AV/IT/electrical components (industrial media player/PC, controller/IoT as applicable, display/sensors/actuators if required, wiring looms, connectors), LED lighting, earthing and safety provisions, packing/forwarding, carriage to site, unloading, erection/installation, anchoring/fastening, alignment, calibration, testing & commissioning, software/content integration, training, documentation (as-built, O&M manual) and minimum 12-month warranty; complete in all respects as per DPR, approved shop drawings and direction of Engineer-in-Charge. |
| 670 | SITC of interactive museum exhibit “The First Cells - Architects of the Atmosphere” for Zone-1, including detailed design/engineering, complete fabrication (MS structure with premium finish; FR/ply/FRP/acrylic/polycarbonate as required), thematic models/props, high-resolution printed graphics with protective laminate, all interactive AV/IT/electrical components (industrial media player/PC, controller/IoT as applicable, display/sensors/actuators if required, wiring looms, connectors), LED lighting, earthing and safety provisions, packing/forwarding, carriage to site, unloading, erection/installation, anchoring/fastening, alignment, calibration, testing & commissioning, software/content integration, training, documentation (as-built, O&M manual) and minimum 12-month warranty; complete in all respects as per DPR, approved shop drawings and direction of Engineer-in-Charge. |
| 671 | SITC of interactive museum exhibit “The Cambrian Explosion” for Zone-2, including detailed design/engineering, complete fabrication (MS structure with premium finish; FR/ply/FRP/acrylic/polycarbonate as required), thematic models/props, high-resolution printed graphics with protective laminate, all interactive AV/IT/electrical components (industrial media player/PC, controller/IoT as applicable, display/sensors/actuators if required, wiring looms, connectors), LED lighting, earthing and safety provisions, packing/forwarding, carriage to site, unloading, erection/installation, anchoring/fastening, alignment, calibration, testing & commissioning, software/content integration, training, documentation (as-built, O&M manual) and minimum 12-month warranty; complete in all respects as per DPR, approved shop drawings and direction of Engineer-in-Charge. |
| 672 | SITC of interactive museum exhibit “The Great Dying - Life's Greatest Challenge” for Zone-2, including detailed design/engineering, complete fabrication (MS structure with premium finish; FR/ply/FRP/acrylic/polycarbonate as required), thematic models/props, high-resolution printed graphics with protective laminate, all interactive AV/IT/electrical components (industrial media player/PC, controller/IoT as applicable, display/sensors/actuators if required, wiring looms, connectors), LED lighting, earthing and safety provisions, packing/forwarding, carriage to site, unloading, erection/installation, anchoring/fastening, alignment, calibration, testing & commissioning, software/content integration, training, documentation (as-built, O&M manual) and minimum 12-month warranty; complete in all respects as per DPR, approved shop drawings and direction of Engineer-in-Charge. |
| 673 | SITC of interactive museum exhibit “Pillar Exhibit - The King of the Narmada” for Zone-3, including detailed design/engineering, complete fabrication (MS structure with premium finish; FR/ply/FRP/acrylic/polycarbonate as required), thematic models/props, high-resolution printed graphics with protective laminate, all interactive AV/IT/electrical components (industrial media player/PC, controller/IoT as applicable, display/sensors/actuators if required, wiring looms, connectors), LED lighting, earthing and safety provisions, packing/forwarding, carriage to site, unloading, erection/installation, anchoring/fastening, alignment, calibration, testing & commissioning, software/content integration, training, documentation (as-built, O&M manual) and minimum 12-month warranty; complete in all respects as per DPR, approved shop drawings and direction of Engineer-in-Charge. |
| 674 | SITC of interactive museum exhibit “The K-Pg Impactor” for Zone-3, including detailed design/engineering, complete fabrication (MS structure with premium finish; FR/ply/FRP/acrylic/polycarbonate as required), thematic models/props, high-resolution printed graphics with protective laminate, all interactive AV/IT/electrical components (industrial media player/PC, controller/IoT as applicable, display/sensors/actuators if required, wiring looms, connectors), LED lighting, earthing and safety provisions, packing/forwarding, carriage to site, unloading, erection/installation, anchoring/fastening, alignment, calibration, testing & commissioning, software/content integration, training, documentation (as-built, O&M manual) and minimum 12-month warranty; complete in all respects as per DPR, approved shop drawings and direction of Engineer-in-Charge. |
| 675 | SITC of interactive museum exhibit “Life After the Asteroid” for Zone-4, including detailed design/engineering, complete fabrication (MS structure with premium finish; FR/ply/FRP/acrylic/polycarbonate as required), thematic models/props, high-resolution printed graphics with protective laminate, all interactive AV/IT/electrical components (industrial media player/PC, controller/IoT as applicable, display/sensors/actuators if required, wiring looms, connectors), LED lighting, earthing and safety provisions, packing/forwarding, carriage to site, unloading, erection/installation, anchoring/fastening, alignment, calibration, testing & commissioning, software/content integration, training, documentation (as-built, O&M manual) and minimum 12-month warranty; complete in all respects as per DPR, approved shop drawings and direction of Engineer-in-Charge. |
| 676 | SITC of interactive museum exhibit “Pillar Exhibit - The 'Narmada Man'” for Zone-5, including detailed design/engineering, complete fabrication (MS structure with premium finish; FR/ply/FRP/acrylic/polycarbonate as required), thematic models/props, high-resolution printed graphics with protective laminate, all interactive AV/IT/electrical components (industrial media player/PC, controller/IoT as applicable, display/sensors/actuators if required, wiring looms, connectors), LED lighting, earthing and safety provisions, packing/forwarding, carriage to site, unloading, erection/installation, anchoring/fastening, alignment, calibration, testing & commissioning, software/content integration, training, documentation (as-built, O&M manual) and minimum 12-month warranty; complete in all respects as per DPR, approved shop drawings and direction of Engineer-in-Charge. |
| 677 | SITC of interactive museum exhibit “The Family Tree” for Zone-5, including detailed design/engineering, complete fabrication (MS structure with premium finish; FR/ply/FRP/acrylic/polycarbonate as required), thematic models/props, high-resolution printed graphics with protective laminate, all interactive AV/IT/electrical components (industrial media player/PC, controller/IoT as applicable, display/sensors/actuators if required, wiring looms, connectors), LED lighting, earthing and safety provisions, packing/forwarding, carriage to site, unloading, erection/installation, anchoring/fastening, alignment, calibration, testing & commissioning, software/content integration, training, documentation (as-built, O&M manual) and minimum 12-month warranty; complete in all respects as per DPR, approved shop drawings and direction of Engineer-in-Charge. |
| 678 | SITC of interactive museum exhibit “The Engine of Life” for Zone-6, including detailed design/engineering, complete fabrication (MS structure with premium finish; FR/ply/FRP/acrylic/polycarbonate as required), thematic models/props, high-resolution printed graphics with protective laminate, all interactive AV/IT/electrical components (industrial media player/PC, controller/IoT as applicable, display/sensors/actuators if required, wiring looms, connectors), LED lighting, earthing and safety provisions, packing/forwarding, carriage to site, unloading, erection/installation, anchoring/fastening, alignment, calibration, testing & commissioning, software/content integration, training, documentation (as-built, O&M manual) and minimum 12-month warranty; complete in all respects as per DPR, approved shop drawings and direction of Engineer-in-Charge. |
| 679 | SITC of interactive museum exhibit “The Sixth Extinction?” for Zone-7, including detailed design/engineering, complete fabrication (MS structure with premium finish; FR/ply/FRP/acrylic/polycarbonate as required), thematic models/props, high-resolution printed graphics with protective laminate, all interactive AV/IT/electrical components (industrial media player/PC, controller/IoT as applicable, display/sensors/actuators if required, wiring looms, connectors), LED lighting, earthing and safety provisions, packing/forwarding, carriage to site, unloading, erection/installation, anchoring/fastening, alignment, calibration, testing & commissioning, software/content integration, training, documentation (as-built, O&M manual) and minimum 12-month warranty; complete in all respects as per DPR, approved shop drawings and direction of Engineer-in-Charge. |
| 680 | SITC of interactive museum exhibit “A Message for Tomorrow” for Zone-7, including detailed design/engineering, complete fabrication (MS structure with premium finish; FR/ply/FRP/acrylic/polycarbonate as required), thematic models/props, high-resolution printed graphics with protective laminate, all interactive AV/IT/electrical components (industrial media player/PC, controller/IoT as applicable, display/sensors/actuators if required, wiring looms, connectors), LED lighting, earthing and safety provisions, packing/forwarding, carriage to site, unloading, erection/installation, anchoring/fastening, alignment, calibration, testing & commissioning, software/content integration, training, documentation (as-built, O&M manual) and minimum 12-month warranty; complete in all respects as per DPR, approved shop drawings and direction of Engineer-in-Charge. |
| 681 | SITC of exhibit-scope thematic partitions/feature walls/column wraps, including supply of all materials, labour, T&P, scaffolding, carriage to site, installation/fixing, making good, testing (where applicable) and handing over complete as per approved drawings and direction of Engineer-in-Charge; comprising GI/Al framework, FR grade board/ply backing, thematic cladding/texture (ACP/FRP/foam/laminate/paint as required), access panels, edge trims, fasteners and making good, complete. |
| 682 | SITC of complete gallery graphics & signage package, including supply of all materials, labour, T&P, scaffolding, carriage to site, installation/fixing, making good, testing (where applicable) and handing over complete as per approved drawings and direction of Engineer-in-Charge; including design adaptation, UV/eco-solvent prints on ACP/FR/foam board, anti-graffiti/UV laminate, bilingual-ready panels, wayfinding, mounting hardware, alignment and finishing complete. |
| 683 | SITC of exhibit-scope lighting system, including supply of all materials, labour, T&P, scaffolding, carriage to site, installation/fixing, making good, testing (where applicable) and handing over complete as per approved drawings and direction of Engineer-in-Charge; including track/spot luminaires, drivers, wiring from nearest point, aiming/focusing, local controls as required, CRI>90 LEDs, testing and commissioning complete. |
| 684 | SITC of AV/IT infrastructure for exhibits, including supply of all materials, labour, T&P, scaffolding, carriage to site, installation/fixing, making good, testing (where applicable) and handing over complete as per approved drawings and direction of Engineer-in-Charge; including 42U rack, UPS, managed switches, patch panels, PDUs, Cat6 networking, floor boxes, cable trays/conduits, labeling, earthing and testing complete. |
| 685 | SITC of detailed design development & integration engineering services, including supply of all materials, labour, T&P, scaffolding, carriage to site, installation/fixing, making good, testing (where applicable) and handing over complete as per approved drawings and direction of Engineer-in-Charge; including detailing, coordination with civil/MEP, prototype/mock-up allowance, shop drawings, BOM finalization, FAT/SAT readiness and sample approvals complete. |
| 686 | SITC of testing, commissioning, training and documentation package, including supply of all materials, labour, T&P, scaffolding, carriage to site, installation/fixing, making good, testing (where applicable) and handing over complete as per approved drawings and direction of Engineer-in-Charge; including system integration tests, user training, O&M manuals, as-built drawings, and common spares/consumables kit complete. |
| 687 | SITC of Interactive Kiosk-1 \\"Universe Explorer\\" including MS kiosk body with FR/HPL finish, 43\\" touch display, mini-PC, bilingual UI/content, speakers (if required), all wiring, earthing, mounting/anchoring, installation, testing & commissioning complete. |
| 688 | SITC of Interactive Kiosk-2 \\"Optics Simulator\\" including MS kiosk/desk with FR/HPL finish, 32–43\\" touch display, mini-PC, bilingual UI/content, all wiring, earthing, mounting/anchoring, installation, testing & commissioning complete. |
| 689 | SITC of Prism & Lens Hands-on Workbench (mechanical) including MS frame, HPL top, acrylic viewing window, prism mount, lens sliders/rails, LED safe light source, bilingual instruction panel, lockable service bay, wiring, earthing, installation, testing & commissioning complete. |
| 690 | SITC of Galileo Telescope Replica Model with interpretive pedestal including model fabrication (wood/FRP), acrylic protection, bilingual panel, anchoring, finishing, installation and testing complete. |
| 691 | SITC of Telescope Mount Types Demo (manual) including mini alt-az / equatorial demonstrator with safe stops, bearings, MS pedestal, bilingual panel, anchoring, finishing, installation and testing complete. |
| 692 | SITC of Radio Listening Station (open) including console cabinet, headphones with volume limiter, audio player, bilingual panels, wiring, fixing, installation, testing & commissioning complete. |
| 693 | SITC of Space Telescopes Media Display (non-touch) including 43–55\\" 4K display, media player, wall mount, cable concealment, short video loop setup, bilingual captions, wiring, installation, testing & commissioning complete. |
| 694 | SITC of modular thematic wall cladding system with MS frame, FR boards, putty/primer/PU paint, trims, fixing and making good complete (graphics measured separately). |
| 695 | SITC of bilingual zone story wall graphics on FR board/ACP with matte anti-glare lamination, including design adaptation, printing, mounting and fixing complete. |
| 696 | SITC of premium feature panoramic wall graphics (timeline/space telescope hero) with matte anti-glare lamination, including printing and installation complete. |
| 697 | SITC of bilingual interpretive panels/labels on ACP/FR board with matte anti-glare lamination, standoff fixing, complete. |
| 698 | SITC of backlit lightbox panels (spectra/constellations) including LED drivers, acrylic face, printed film, MS box, wiring and fixing complete. |
| 699 | SITC of simple ceiling acoustic/star-canopy panels (select areas) including frame, acoustic backing, fire-retardant fabric/print, fixing complete. |
| 700 | SITC of floor wayfinding graphics + skirting bands in durable laminate/vinyl with protection coat, complete. |
| 701 | SITC of track lights / wall washers (CRI>90) including drivers, wiring terminations, aiming, testing complete. |
| 702 | SITC of exhibit electrical raceways + floor boxes/points including conduits, accessories, termination and making good complete. |
| 703 | SITC of cabinets / storage / undercounter units (lab + AV) including MS frame, HPL finish, locks, hinges, ventilation, complete. |
| 704 | SITC of safety & protection works including corner guards, edge protection, stanchions/rope barriers for model, sealants, surface protection & final touch-ups complete. |
| 705 | SITC of 12U AV/IT rack with PDU, fan tray, patch panel, 16-port managed switch, internal wiring, labeling, complete. |
| 706 | SITC of Cat6 structured cabling (supply, laying, terminations, faceplates, testing) complete. |
| 707 | SITC of Online UPS 2 kVA with batteries, changeover, earthing and commissioning complete. |
| 708 | SITC of HDMI/patch cords/spares kit (assorted) complete. |
| 709 | SITC of surge protection/earthing accessories for AV rack and displays complete. |
| 710 | SITC of bilingual content/UI development for both kiosks including scripts, UI screens, media assets, integration, testing and deployment complete (offline operation). |
| 711 | SITC of short motion graphics/video loops pack (royalty-free) for media display and kiosks, including editing, captions and optimization complete. |
| 712 | SITC of installation labour, tools & tackles for exhibits/decor/graphics including alignment, anchoring, fixing and making good complete. |
| 713 | SITC of testing & commissioning including electrical safety tests, burn-in, punch list closure complete. |
| 714 | SITC of documentation including as-built drawings, wiring diagrams, O&M manuals, asset register complete. |
| 715 | SITC of training & handover for operators/maintenance team complete. |
| 716 | SITC of O&M spares kit (PSUs, cables, one spare media player, headphone pads, cleaning kit, consumables) complete. |
| 717 | SITC of Exhibit E1.1 “Himalayan Thaw” – VR Experience (footprint 15 sq.m) including all fabrication, AV/IT hardware, software/content integration, mounting, cabling, installation, testing & commissioning, as-built documentation, O&M manuals, operator training, including Defects Liability Period (DLP) of 12 months from date of handover, covering rectification of manufacturing/fabrication defects. |
| 718 | SITC of Exhibit E1.2 “The Ghost Reef” – Interactive Projection Wall (footprint 20 sq.m) including all fabrication, AV/IT hardware, software/content integration, mounting, cabling, installation, testing & commissioning, as-built documentation, O&M manuals, operator training, including Defects Liability Period (DLP) of 12 months from date of handover, covering rectification of manufacturing/fabrication defects. |
| 719 | SITC of Exhibit E1.3 “The Sundarbans' Edge” – Holographic Diorama (footprint 12 sq.m) including all fabrication, AV/IT hardware, software/content integration, mounting, cabling, installation, testing & commissioning, as-built documentation, O&M manuals, operator training, including Defects Liability Period (DLP) of 12 months from date of handover, covering rectification of manufacturing/fabrication defects. |
| 720 | SITC of Exhibit E1.4 “Extreme Weather Weaver” – Data Visualization Sculpture (footprint 10 sq.m) including all fabrication, AV/IT hardware, software/content integration, mounting, cabling, installation, testing & commissioning, as-built documentation, O&M manuals, operator training, including Defects Liability Period (DLP) of 12 months from date of handover, covering rectification of manufacturing/fabrication defects. |
| 721 | SITC of Exhibit E1.5 “Species on the Move” – Augmented Reality Wall Map (footprint 8 sq.m) including all fabrication, AV/IT hardware, software/content integration, mounting, cabling, installation, testing & commissioning, as-built documentation, O&M manuals, operator training, including Defects Liability Period (DLP) of 12 months from date of handover, covering rectification of manufacturing/fabrication defects. |
| 722 | SITC of Exhibit E2.1 “The Carbon Blanket” – Multi-user Interactive Table (footprint 12 sq.m) including all fabrication, AV/IT hardware, software/content integration, mounting, cabling, installation, testing & commissioning, as-built documentation, O&M manuals, operator training, including Defects Liability Period (DLP) of 12 months from date of handover, covering rectification of manufacturing/fabrication defects. |
| 723 | SITC of Exhibit E2.2 “Archives of the Earth” – Physical + AR Exhibit (footprint 9 sq.m) including all fabrication, AV/IT hardware, software/content integration, mounting, cabling, installation, testing & commissioning, as-built documentation, O&M manuals, operator training, including Defects Liability Period (DLP) of 12 months from date of handover, covering rectification of manufacturing/fabrication defects. |
| 724 | SITC of Exhibit E2.3 “Tipping Points” – Interactive Projection Map (footprint 15 sq.m) including all fabrication, AV/IT hardware, software/content integration, mounting, cabling, installation, testing & commissioning, as-built documentation, O&M manuals, operator training, including Defects Liability Period (DLP) of 12 months from date of handover, covering rectification of manufacturing/fabrication defects. |
| 725 | SITC of Exhibit E2.4 “Carbon Footprint Calculator” – Personal Interactive Kiosks (x4) (footprint 10 sq.m) including all fabrication, AV/IT hardware, software/content integration, mounting, cabling, installation, testing & commissioning, as-built documentation, O&M manuals, operator training, including Defects Liability Period (DLP) of 12 months from date of handover, covering rectification of manufacturing/fabrication defects. |
| 726 | SITC of Exhibit E3.1 “Bareilly 2050” – Collaborative City-Builder Game (footprint 25 sq.m) including all fabrication, AV/IT hardware, software/content integration, mounting, cabling, installation, testing & commissioning, as-built documentation, O&M manuals, operator training, including Defects Liability Period (DLP) of 12 months from date of handover, covering rectification of manufacturing/fabrication defects. |
| 727 | SITC of Exhibit E3.2 “The Solutions Showcase” – AR-Enhanced Physical Models (footprint 18 sq.m) including all fabrication, AV/IT hardware, software/content integration, mounting, cabling, installation, testing & commissioning, as-built documentation, O&M manuals, operator training, including Defects Liability Period (DLP) of 12 months from date of handover, covering rectification of manufacturing/fabrication defects. |
| 728 | SITC of Exhibit E3.3 “The Pledge Wall” – Interactive Digital Installation (footprint 10 sq.m) including all fabrication, AV/IT hardware, software/content integration, mounting, cabling, installation, testing & commissioning, as-built documentation, O&M manuals, operator training, including Defects Liability Period (DLP) of 12 months from date of handover, covering rectification of manufacturing/fabrication defects. |
| 729 | SITC of Exhibit E3.4 “The Circular Economy Engine” – Physical Ball Machine Interactive (footprint 15 sq.m) including all fabrication, AV/IT hardware, software/content integration, mounting, cabling, installation, testing & commissioning, as-built documentation, O&M manuals, operator training, including Defects Liability Period (DLP) of 12 months from date of handover, covering rectification of manufacturing/fabrication defects. (AMC/CMC excluded.) |
| 730 | SITC of Exhibit E3.5 “Future of Food” – Olfactory & Tactile Display (footprint 8 sq.m) including all fabrication, AV/IT hardware, software/content integration, mounting, cabling, installation, testing & commissioning, as-built documentation, O&M manuals, operator training, including Defects Liability Period (DLP) of 12 months from date of handover, covering rectification of manufacturing/fabrication defects. |
| 731 | SITC of Exhibit E4.1 “The Global Weave” – Interactive Data Sculpture (footprint 30 sq.m) including all fabrication, AV/IT hardware, software/content integration, mounting, cabling, installation, testing & commissioning, as-built documentation, O&M manuals, operator training, including Defects Liability Period (DLP) of 12 months from date of handover, covering rectification of manufacturing/fabrication defects. |
| 732 | Partitions – curved/low (MS frame + FR ply + acoustic backing) |
| 733 | Projection-ready wall + floor surface prep (Level-5 + screen paint / matte floor coat) |
| 734 | Acoustic backing panels (PET felt/perf MDF + mineral wool) |
| 735 | Feature wall data-art murals (print + laminate + protection) |
| 736 | Biodiversity silhouette cut-panels (CNC ACP/ply, installation) |
| 737 | Loose + built-in cabinetry (lockable, vented) |
| 738 | Server/rack enclosure (lockable, vented, acoustic lined) |
| 739 | Tactile guidance strips/tiles incl. adhesive and fixing |
| 740 | Inclusive seating / rest nodes |
| 741 | Photo-op points with queue pocket markings and signage |
| 742 | Special finishes & protective coatings (anti-graffiti, FR coatings, edge protections) |
| 743 | Bilingual interpretive panels (Hindi+English) – print on ACP/acrylic with matte lamination, mounting hardware |
| 744 | Wayfinding and regulatory signage set (zone totems, directionals, safety signs) |
| 745 | Graphic design services (templates, iconography, typographic hierarchy, layout files) |
| 746 | Printing, lamination, cutting, mounting accessories and installation consumables |
| 747 | Accessibility graphics (high-contrast, tactile labels/Braille for key elements, QR workflow) |
| 748 | 42U 19-inch server rack with PDU, cable managers, lockable doors, ventilation |
| 749 | Online UPS 10 kVA (with battery for min 15 min at critical load) |
| 750 | Core 10Gb managed switch (24-port SFP+/10Gb) |
| 751 | PoE+ access switch (48-port, managed) |
| 752 | Firewall / gateway router with VLAN support |
| 753 | Fiber uplink modules, patch panels, LIU, ODF, splicing, testing |
| 754 | Structured cabling Cat6A (supply + laying + testing + labeling) |
| 755 | Wi‑Fi 6 access points with controller/configuration |
| 756 | Patch cords, keystone jacks, trays, accessories, earthing |
| 757 | Network configuration, VLAN setup, documentation and handover |
| 758 | Testing, commissioning, training, documentation (FAT/SAT, O&M manuals, as-builts, staff training) |
| 759 | P-1 Planetarium Theatre (Decor): Wall-to-wall carpet, stain-resistant, Class-B FR; underlay & transitions included. |
| 760 | Double-layer acoustic panels with mineral wool backing and fabric finish to 3.0 m height around full perimeter; aluminium trims; concealed fixings. |
| 761 | MR-MDF subframe with HPL/PU finish; edge banding; GI brackets; height 1.2 m around full perimeter. |
| 762 | HPL/solid-surface skirting; corners and end-caps; continuous at public edges. |
| 763 | Premium reclining theatre chair with cup holder; FR fabric; ergonomic design; integrated aisle markers. |
| 764 | Low-glare step-edge/aisle LED with DMX drivers/decoders and local control nodes; addressing & labelling. |
| 765 | Anchoring, alignment, row spacing, fixing; inspection and load test per row; as-builts. |
| 766 | On-site aiming/focus; scene setup & dimming curves; addressing; documentation. |
| 767 | Digital Planetarium Projection System & Components: (a) Fulldome Video Projection System: Projectors: • Quantity: 2 Units • Illumination Technology: Laser Phosphor • Brightness: Up to 14,000 ANSI lumens • Contrast Ratio: 20,000:1 (Dynamic) • Resolution: 4K UHD per projector • On-Dome Resolution: Over 3850 pixels across the diameter • Lifespan: 20,000 hours of operation (b) PC Cluster & P-1 Planetarium Theatre (Equipment & Fitout)Servers: Graphics Servers:• Quantity: 2 Units • Model: High-performance Rack-mounted Server (4RU) • CPU: High-performance Workstation Class Processor (e.g., Intel Xeon W-2225 or equivalent) • Memory: 32 GB • Storage: 2GB SSD System Drive, 8GB SSD Content Drive • Graphics: Professional-grade Graphics Card with Frame Sync capability • OS: Professional/Enterprise Grade Stable Operating System. Host cum Audio Server: • Quantity: 1 Unit • Model: High-performance Rack-mounted Server (4RU) • CPU: High-performance Workstation Class Processor (e.g., Intel Xeon W-2225 or equivalent) • Memory: 32 GB • Storage: 2GB SSD System Drive, 8GB SSD Content Drive • Graphics: Professional-grade Graphics Card • OS: Professional/Enterprise Grade Stable Operating System, (c) Automatic Alignment & Calibration System: • Function: Automated geometry, gamma, and blend correction for seamless imaging across multiple projectors • Components: Permanently installed digital cameras for viewing the dome • Runtime: Fully automated process should take less than 2 minutes (d) 5.1 Digital Surround-Sound System: • Configuration: 5.1 Surround Sound • Speakers: 5 x Professional Cinema Series Loudspeakers • Subwoofer: 1 x Professional Cinema Series Sub-bass Cabinet • Amplifiers: Professional Cinema Amplifiers with integrated loudspeaker control • Signal Processing: Digital audio networking protocol for signal distribution, with DSP unit and digital mixer, (e) Software & Control System: • Software: Fulldome Control and Visualization Software • Features: Real-time astronomical rendering , timeline-based show creation with scrubbing capability , drag-and-drop interface , and integrated Theater Automation. • Content: Must include extensive astronomical databases (Stars, Asteroids, Galaxies) , support for scientific datasets , and compatibility with numerous media formats. • Control: To include an operator console with 2 dimmable monitors (dimmable to 1%) , a tablet for remote control , and a programmable digital manual controller. (f) Fulldome Content Package: • Licensed Fulldome Show: 2 Unit of a 4K 2D show with a 3-year license. • Additional Shows: An initial collection of fulldome shows provided free of charge. • Clips & Sequences: A collection of royalty-free clips and sequences for presentations. (g) Customs Duty: • Applicable Customs Duty @ 11% on imported value of INR 4,19,35,000.00 |
| 768 | Projection Dome - FRP Projection Dome Screen: • Diameter: 12 meters • Type: Horizontal, Self-supported hemispherical • Material: Fiberglass Reinforced Plastic (FRP) • Surface: Non-perforated for best projection quality • Internal Finish: Smooth, single-dome effect, off-white, non-glossy • Construction: 12 segments and a top cap, assembled at site • Thickness: 3.5-5 mm mean • Weight: Approx. 1.5 Tons |
| 769 | Services & Local Items (a) Installation & Commissioning: Complete supply, installation, integration, testing, and commissioning of the entire planetarium system. (b) Uninterruptible Power Supply (UPS): 2 x 10 KVA parallel redundant UPS. (c) Warranty, Maintenance & Operation: • 1-year comprehensive warranty on the complete installation • 2 years additional Comprehensive Maintenance Service (AMC) post-warranty • Daily operation services included in the contract period • On-site \\"show-stopper\\" spare parts supply • 24/7 remote support Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
