|
| 1 | Taking down chowkhats with shutters (without taking off shutters from the frames) & removing from site area n.exc 1.5 Sqm each complete all as directed. |
| 2 | Taking down chowkhats with shutters (without taking off shutters from the frames) & removing from site area exc 1.5 Sqm & n. exc 4.00 sqm each complete all as directed. |
| 3 | Taking down Shutters of any description not exceeding 1.0 sqm for each leaf all as specified. |
| 4 | Taking down Shutters of any description exceeding 1.0 sqm but not exceeding 2.0 sqm for each leaf all as specified. |
| 5 | Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified. |
| 6 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering complete all as directed. |
| 7 | Dismantling fibre glass reinforced translucent corrugated sheeting of any thickness in roof covering complete all as directed by Engineer-In-Charge. |
| 8 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as directed by Engineer-In-Charge. |
| 9 | Dismantling boarding, any description, fixed in any position with nails complete all as directed. |
| 10 | Dismantling timber scantlings 40 sqcm and over in section for unframed work, in any position all as directed. |
| 11 | Dismantling fillets, rails, posts, rafters, purlins, etc. under 40 sqcm in section for unframed work complete all as directed. |
| 12 | Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets all as directed. |
| 13 | Demolition of cement Concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as directed. |
| 14 | Demolition of cement concrete of any description and in any position complete all as specified. |
| 15 | Demolition of reinforced cement concrete of any description and in any position complete all as specified. |
| 16 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises all as directed by Engr- In- Charge. |
| 17 | Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified. |
| 18 | Demolition of Precast concrete block/ Brickwork or stone/boulder masonry, laid with cement morter complete all as directed. |
| 19 | Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store 15 mm dia |
| 20 | Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store 20 mm dia |
| 21 | Supply and fix pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed. |
| 22 | Supply and fix pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed. |
| 23 | Supply and fix 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with L-type or J-type or cranked hook bolts in lieu of screw using profiled GI washer and bitumen washer in roof covering complete all as specifed and directed. |
| 24 | Supply and fix as in repairs 2 mm thick polycarbonate solid embossed sheet fixing with self tapping screws complete all as per manufacturer instruction. |
| 25 | Supply and fix steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161- 1979 grade St.-240 complete all as specified. |
| 26 | Material and labour for joint, channel, angle or tee sections, mild steel tubes medium grade fixed independently, without connecting plates, etc (cut to ordinary lengths i.e. within 20 mm of the length indicated) also fastening and fixing conforming to Fe-410W Grade E-250 (quality A) complete all as specified and directed. |
| 27 | Supply and fix Fe-410-W(GdeE-250) qualityA Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified. |
| 28 | Supply and fix mild steel sheet eaves gutters, 1.5 mm thick 150 mm dia, galvanised class 3, half round with rounded edges complete all as specified. |
| 29 | Supply and fix Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified. |
| 30 | Supply and fix Ball bearing for rolling shutters complete all as specified. |
| 31 | Material and labour for second class hardwood weather boarding, clean sawn, plain, 20mm thick or feather edged 15 mm to 20mm thick and fixed with 30mm laps complete all as specified. |
| 32 | Supply and fix 40 mm thick boarding second class hardwood planed one side, with butt joints and fixed with nails supplied and fixed complete all as specified. |
| 33 | Material and labour for second class hardwood scantling wrought sawn complete all as specified. |
| 34 | Supply and fix 2nd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified. |
| 35 | Material and labour 2nd class hardwood Plain fillets. square,rectangular or triangular in section, clean sawn, secured with nails or brads exceeding 13 sqcm but not exceeding 25 sqcm complete all as specified. |
| 36 | Supply and fix 35 mm thick Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers fitted to chowkats complete all as specified. |
| 37 | Supply and fix 35 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified. |
| 38 | Supply and fix of 35 mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. divided into squares, with out sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. and size of the members of shutter is as specified in clause No. 8.24 (a) of MES schedule 2009, part – I (Specifications). |
| 39 | Supply and fix of 30 mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. divided into squares, with out sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. and size of the members of shutter of windows, ventilators, etc. are provided with stiles and rails as specified in SSR Part I, Section 8 clause 8.24(b). |
| 40 | Supply and fix 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified. |
| 41 | Supply and fix in repairs Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified. |
| 42 | Supply and fix PVC door frame of size 50 mm X 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified. |
| 43 | Supply and fix 30 mm thick factroy made solid panel PVC door shutter (style) consisting of frame made out of MS tube for top and bottom rails MS frame shall be covered with neat moulded plain colour PVC channel having a PVC sheet strip of 20mm width stuct inside the solvent cement for style and single side pre laminated PVC sheet for top rails, lock rails and bottom rails on either side and as gap insert for top rails and bottom rail panelling of plain colour PVC sheet to be fitted in the MS frame welded to the style and rails with suitable PVC sheet beading and jointed together with solvent cement supplying and fixing in the frame at site as per specification . |
| 44 | Supply and fix 0.63 mm thick plain, galvanised, mild steel sheeting in stepped flashings (measured as the minimum rectangle from which the pieces can be cut) complete all as specified. |
| 45 | Supply and fix bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified. |
| 46 | Supply and fix powder coated anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified |
| 47 | Supply and fix anodised aluminium door shutters with powder coating of any colour (Thickness or powder coating not less than 50 micron), aluminium section weighing not less than 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, 4 lever mortice lock, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified |
| 48 | Supply and fix powder coated aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified |
| 49 | Supply and fix powder coated aluminium window and ventilator shutters powder coating of any colour (Thickness or powder coating not less than 50 micron), side hung/ sliding type without sash bars, aluminium sections weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified |
| 50 | Supply and fix anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-In- charge. |
| 51 | Supply and fix 9 mm thick prelaminated particle board, exterior grade,prelaminated both sides with decorative choice laminations fixed with screws to timber frame work complete all as specified. |
| 52 | Supply and fix 4.80 mm thick sheet glass, ordinary quality and glazing in square exceeding 0.50 sqm in each pane in aluminium joinery in each pane complete all as specified. |
| 53 | Supply and fix 3 mm thick sheet glass, ordinary quality and glazing in square exceeding 0.50 sqm in each pane in aluminium joinery in each pane complete all as specified. |
| 54 | Supply and fix 4 mm thick figured glass, pin head type and glazing in square exceeding 0.50 sqm in each pane in aluminium joinery in each pane complete all as specified. |
| 55 | Supply and fix galvanised mild steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified. |
| 56 | Supply and fix as in repairs galvanised mild steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified. |
| 57 | Supply and fix as in repairs aluminium (die cast body) Door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 851 mm to 1000 mm in width and of weight between 61 kg to 80 kg and fixed complete all as specified. |
| 58 | Supply and fix 100 mm long medium weight, cold rolled mild steel, Butt hinges, complete all as specified. |
| 59 | Supply and fix 75 mm long medium weight, cold rolled mild steel, Butt hinges, complete all as specified. |
| 60 | Supply and fix 100 mm long aluminium alloy handles, fabricated type, anodized all as specified. |
| 61 | Supply and fix 150 mm long aluminium alloy handles, fabricated type, anodized all as specified. |
| 62 | Supply and fix 100 mm long aluminium anodised barrel tower bolts of extruded section all as specified. |
| 63 | Supply and fix 200 mm long aluminium anodised barrel tower bolts of extruded section all as specified. |
| 64 | Supply and fix 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified. |
| 65 | Supply and fix as in repairs 18/19 mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified. |
| 66 | Supply and fix as in repairs 12 mm thick plywood, grade BWR, type BB, fixed with screws to timber frame work complete all as specified. |
| 67 | Material and labour 2nd class hardwood Plain fillets. square,rectangular or triangular in section, clean sawn, secured with nails or brads not exceeding 3 sqcm complete all as specified. |
| 68 | Supply and fix as in repairs 40 mm width of flap (when open) continuous (piano) hinges, mild steel, bright finish or electro galvanised complete all as specified. |
| 69 | Supply and fix as in repairs 4 lever brass Mortice lock, vertical type, size 100 mm (set of 2 keys) complete all as specified. |
| 70 | Supply and fix 4 lever brassMortice lock, vertical type, size 100 mm (set of 2 keys) complete all as specified. |
| 71 | Supply and fix as in repairs 100 mm long hasp and staple, of aluminium anodised including bolt to hinge plate and fixed with screws complete all as specified. |
| 72 | Supply and fix as in repairs magnetic catches for wardrobe, almirah complete all as specified. |
| 73 | Supply and fix floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor overall size of cover plate 140 mm complete all as specified. |
| 74 | Supply and fix as in repairs floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor overall size of cover plate 140 mm complete all as specified. |
| 75 | Supply and fix stainless steel wall cloth hooks set of 6 prongs suitable for bathroom, kitchen etc complete all as directed by Engineer-In-Charge. |
| 76 | Supply and fix door bottom seal 90 cm-100 cms in length 42 mm wide including aluminium plate (22mmx6.16mm thk) with nylon brush (20 mm wide) fixed with tapping screw as per manufacturer instruction. |
| 77 | Material and labour for for suspended false ceiling using grid 180 GSM (exposed ceiling suspension system ) of grid size 605 mm x 605 mm with main runner 38 mm x 24 mm and wall angle 24 mm x 24 mm using 4 mm thick High Pressure steel Non Asbestos Fibre Cement decorative Board in a grid of powder coated GI system duly suspended with 4 mm dia GI bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures, air conditioning diffuser and ducts ,sprinkler ,smoke detectors etc. The main runners to be secured to structural soffits by hanger @ 1210 mm maximum c/c. the last hanger at the end of each main runner should not be placed at more than 450 mm from the adjacent wall, Flush fitting 1210 mm cross tee to be interlocked between main runners @ 605 mm c/c,so as to form 600 mm x 600 mm grid complete all as specified . |
| 78 | Supply and fix 4 mm thick non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws complete all as specified. |
| 79 | Material and labour 2nd class hardwood Plain fillets. square,rectangular or triangular in section, clean sawn, secured with nails or brads exceeding 3 sqcm but not exceeding 6 sqcm complete all as specified. |
| 80 | Material and labour for 7 mm thick joint free premium quality glazed ceramic colour tiles of size 350 mm x 250 mm/ 450 mm x 300 mm/ 600 mm x 300 mm as in skirting / dado / vertical surfaces set and jointed and pointed in white or colour cement to match existing surfaces including 10 mm thick rendering in cement mortar 1:3 complete all as specified. |
| 81 | Material and labour for 7 mm thick joint free premium quality glazed ceramic colour tiles of size 300 mm x 200 mm as in skirting / dado / vertical surfaces set and jointed and pointed in white or colour cement to match existing surfaces including 10 mm thick rendering in cement mortar 1:3 complete all as specified. |
| 82 | Material and labour for 7 to 8 mm thick joint free premium quality anti skid colour ceramic tiles size of each tiles should be 300 mm x 300 mm as in floors set and jointed and pointed in white or colour cement to match existing surfaces including 20 mm thick screed bed in cement mortar 1:4 complete all as specified. |
| 83 | Material and labour for 7 to 8 mm thick joint free premium quality anti skid colour ceramic tiles size of each tiles should be 400 mm x 400 mm as in floors set and jointed and pointed in white or colour cement to match existing surfaces including 20 mm thick screed bed in cement mortar 1:4 complete all as specified. |
| 84 | Material and labour for 7 to 8 mm thick joint free premium quality anti skid colour ceramic tiles size of each tiles should be 400 mm x 400 mm as in skirting / dado / vertical surfaces set and jointed and pointed in white or colour cement to match existing surfaces including 10 mm thick rendering in cement mortar 1:3 complete all as specified. |
| 85 | Material and labour for 10 mm thick joint free premium quality light shed vitrified ceramic tiles of size 600 mm x 600 mm as in floors set and jointed and pointed in white or colour cement to match existing surfaces laid over 20 mm thick screed bed in cement mortar 1:4 complete all as specified. |
| 86 | Material and labour for 10 mm thick joint free premium quality light shed vitrified ceramic tiles of size 600 mm x 600 mm as in skirting/ dado/ vertical surfaces set and jointed and pointed in white or colour cement to match existing surfaces including 10 mm thick rendering in cement mortar 1:3 complete all as specified. |
| 87 | Supply and fix Pavement floor vitrified tiles of size 300x 300x 10 mm thk (Endura tiles of Johnson or equivalent makes listed in List of Makes) of approved colour and design set and jointed in neat cement slurry and pointed in white or coloured to match including 20 mm th screed bed in cement mortar 1:4 complete all as specified and directed. |
| 88 | Material and labour 40 mm thick PCC type B1, 1:2:4 using 20 mm graded crushed stone aggregates as in floor surfaces including finishing the concrete surface even & smooth without using extra cement complete all as specified. |
| 89 | Material and labour for cement concrete type B0, 1:2:4 (12.50mm graded aggregate), rounded or chamfered on edges in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, coping kneelers, apex stones, bed plates, kerbs not provided for roof kerbs or mud stops, rounded or chamfered on edges, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including water proofing compound complete all as specified |
| 90 | Material and labour 50 mm thick PCC type C2, 1:3:6 using 40mm graded crushed stone aggregates as in hard standing/plinth protection including finishing the concrete surface even & smooth without using extra cement and laid in alternate bay complete all as specified. |
| 91 | Material and labour for PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregates as in Foundation, filling and mass concrete complete all as specified. |
| 92 | Material and labour for Reinforced cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies deck slabs, and in shelves and the like complete all as specified and directed. |
| 93 | Material and labour for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed. |
| 94 | Material and labour for Use and waste of flat formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces of concrete complete all as specified and directed. |
| 95 | Material and labour for 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 20 mm thick screed bed in cement mortar 1:4, including edge moulding of counters vanities etc. and machine polishing to edge to give high gloss finish etc. including demolition complete all as specified. |
| 96 | Material and labour for brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in in cement mortar 1:4 complete all as specified. |
| 97 | Material and labour for brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4, in walls complete all as specified. |
| 98 | Material and labour for 15 mm thick rendering on fair faces of brick or concrete surfaces in cement mortar 1:6 finshed even and smooth without using extra cement complete all as specified. |
| 99 | Material and labour for 5 mm thick rendering in cement mortar 1:3 on fair faces of ceiling surfaces, finished the surfaces even and smooth without using extra cement complete all as specified. |
| 100 | Material and labour for 15 mm thick rendering in cement mortar 1:4 in two layers (10 mm +5 mm) on external faces of brick wall or concrete surfaces, finished the surfaces even and smooth without using extra cement with using approved Liquid Water Proofing Compound on second layer (5 mm) as per manufacturer instruction complete all as specified and as directed by Engineer-In-Charge. Note: Liquid Water Proofing Compound shall be measured and paid including this item |
| 101 | Material and labour for 10 mm thick rendering on fair faces of brick or concrete surfaces in cement mortar 1:4 finshed even and smooth without using extra cement complete all as specified. |
| 102 | Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified. |
| 103 | Supply and fix as in repairs Rotational moulded polyethylene water storage overhead tanks (cylindrical vertical with closed top) multi layered 500 ltr capacity hoisted and fixed in position including 20 mm dia Ball valves (Minimum weight of valve 210 gms) high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe complete all as specified. |
| 104 | Supply and fix as in repairs Rotational moulded polyethylene water storage overhead tanks (cylindrical vertical with closed top) multi layered 1000 ltr capacity hoisted and fixed in position including 20 mm dia Ball valves (Minimum weight of valve 210 gms) high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe complete all as specified. |
| 105 | Supply and fix as in repairs float ball valves 20mm dia high pressure PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed complete all as specified and as directed by Engineer-In-Charge. |
| 106 | Disconnecting existing tanks of Capacity exceeding 250 ltr but not exceeding 500 ltr, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including cleaning repairing, etc.as directed by Engineer-In-Charge. |
| 107 | Disconnecting existing tanks of Capacity exceeding 500 ltr but not exceeding 1000 ltr, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including cleaning repairing, etc.as directed by Engineer-In-Charge. |
| 108 | Supply, lay and fix 15 mm bore galvanized iron water tubing medium grade including all fittings and fixed complete to walls and ceiling or laid in floors all as specified. |
| 109 | Supply, lay and fix 20 mm bore galvanized iron water tubing medium grade including all fittings and fixed complete to walls and ceiling or laid in floors all as specified. |
| 110 | Laying Only 15 mm bore galvanized iron water tubing medium grade including all fittings and fixed complete to walls and ceiling or laid in floors all as specified. |
| 111 | Laying only 20 mm bore galvanized iron water tubing medium grade including all fittings and fixed complete to walls and ceiling or laid in floors all as specified. |
| 112 | Supply and fix as in repairs vitreous china wash down water closet pan (pedestal pattern) with seat and cover closed pattern flat bottom, and mild steel chromium plated or aluminised hinging device white colour with 'P' or 'S' trap including connection to drains (or outgoing pipes) and to the flushing pipes, complete all as per manufacturer instruction |
| 113 | Supply and fix one piece Vitreous China wash down water closet pan floor mounted, white including fixing bolts, 10 ltr capacity flushing cistern,flush pipe plastic water closet seat white including jet spray, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging devices and also including 'P' or 'S' trap including taking out old pedestal alongwith existing all fittings and making the surface match with existing surface complete all as per manufacturer instruction. |
| 114 | Supply and fix as in repairs soft closing plastic water closet seat cover , white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified. |
| 115 | Supply and fix as in repairs 10 ltrs capacity PVC valveless syphonic action type, low level flushing cistern, white with inlet, ball valve float and handle including brackets and 32 mm dia PVC low or high density flush pipe complete all as per manufacturer instruction |
| 116 | Supply and fix as in repairs Vitreous China wash basin, white, flat back, size 550 mm x 400 mm including 32 mm dia waste fittings and waste pipe including brackets complete all as specified. |
| 117 | Supply and fix as in repair vitreous china wash basin oval type of size 545x400x185mm including 32mm dia waste fitting including brackets and 32mm dia waste fitting with PVC drainage waste pipe required length upto floor trap complete all as specified. |
| 118 | Supply and fix as in repairs, brass CP quarter turn basin mixer swan neck pattern for mixing hot and cold water including 15 mm bore hot water pipe duly insulated with glass wool and aluminium cladding complete all as specified. |
| 119 | Supply and fix as in repairs 15 mm bore CP pillar tap,pressmatic with aerator complete as per manufacturer instruction. |
| 120 | Supply and fix as in in repairs 32 mm dia waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified. |
| 121 | Supply and fix as in repairs 32 mm bore bottle trap of PTMT having minimum water seal of 25mm of Minimum weight 260gms complete all as specified. |
| 122 | Supply and fix as in repairs sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste coupling and waste pipe; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mm x 460 mm bowl size 410mm x 330mm x 160mm complete all as specified. |
| 123 | Supply and fix as in repairs sinks without drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste coupling and waste pipe; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified. |
| 124 | Supply and fix as in in repairs 40 mm dia waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified. |
| 125 | Supply and fix as in repairs PVC flexible sink/wash basin waste pipe drain hose/ outlet pipe of 35 inches as spesified and directed |
| 126 | Supply and fix in repair chromium plated Sink mixer for mixing hot & cold water, wall mounted swan neck pattern screwed down for iron pipe and fixed complete all as per manufacturer instruction. |
| 127 | Supply and fix as in repairs for 15 mm bore Chromium plated fancy type long neck Bip taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as directed. |
| 128 | Supply and fix as in repairs 15 mm dia cast copper alloy chromium plated Angle valves, with wall flange concealed type screwed down for iron pipe of for unions complete all as specified and directed. |
| 129 | Material and labour in repair for 15 mm dia brass CP two way Angle valve with wall flange concealed type screwed down for iron pipe or for unions complete all as per manufacturer instruction. |
| 130 | Supply and fix as in repairs for 15 mm dia cast copper alloy chromium plated two way Bib cock with wall flange concealed type screwed down for iron pipe or for unions complete all as Per manufacturer instruction. |
| 131 | Supply and fix as in repairs CP health faucet with tube and wall hook including all fittings as per manufacturer instruction. |
| 132 | Supply and fix as in repairs for 15 mm bore dia of pipe Brass CP Wall mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as per manufacturer instruction. |
| 133 | Supply and fix as in repairs brass CP shower rose with or without swivel joints, 125 mm size, including fixing to steel pipe or union complete all as specified. |
| 134 | Supply and fix as in repairs Hand Shower with 8 mm dia and 1.00 mtr long flexible tube and wall hook complete all as directed. |
| 135 | Supply and fix as in repairs 20 mm dia chromium plated tubular towel rail and 600 mm long with brackets, complete all as specified. |
| 136 | Supply and fix as in repairs 20 mm dia chromium plated tubular towel rack and 600 mm long with brackets, complete all as specified. |
| 137 | Supply and fix as in repairs Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified. |
| 138 | Supply and fix as in repairs corner glass shelf of size 300 mm radius (with brass chromium plated brackets) fixed in wall with necessary screws etc. complete all as per directed by Engineer-In-Charge. |
| 139 | Supply and fix as in repairs PVC toilet mirror cabinet with mirror of overall size 350 mm x 450 mm and fixed to wall complete all as per directed by Engineer-In-Charge. |
| 140 | Supply and fix as in repairs 600 mm x 450 mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified. |
| 141 | Supply and fix as in repairs toilet paper holder as per manufacturer instruction. |
| 142 | Supply and fix as in repairs soap dish, fancy type, fixed to plugs with chromium plated brass screws complete all as specified. |
| 143 | Supply and fix as in repairs PVC connections 15 mm size with PTMT nuts of length 450 mm,complete all as specified. |
| 144 | Supply and fix as in repairs 450 mm long CP brass connection pipe with CP brass nuts on both ends for fixing to pipe or other fittings complete all as per existing make. |
| 145 | Supply and fix as in repairs, stainless steel kitchen plate rack of size 610 mm x 914 mm x 254 mm made out of 1 mm thick stainless steel sheet complete all as per manufacturer instruction. |
| 146 | Supply and fix as in repairs Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as directed for 20 mm bore all as specified. |
| 147 | Supply and fix as in repairs 75mm dia PVC (SWR) floor trap, plain with gratings including jointing with solvent cement complete all as specified and directed. Please Enable Macros to View BoQ information |
| 148 | Supply and fix as in repairs 75mm dia PVC (SWR) floor trap, plain with gratings including jointing with solvent cement complete all as specified and directed. Please Enable Macros to View BoQ information |
