|
| 1 | Providing and laying 75 mm thick compacted bed of dry brick aggregate of 40 mm thick nominal size including spreading, well ramming, consolidating and grouting with jamuna sand, including finishing smooth etc. complete as per direction of Engineerin- charge. |
| 2 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 3 | 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 4 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 5 | Foundations, footings, bases of columns, etc. for mass concrete |
| 6 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. |
| 7 | 15 mm nominal bore |
| 8 | Providing and fixing PTMT/SS towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangementof approved quality and colour. |
| 9 | 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms |
| 10 | Providing and fixing C.P. Brass extension nipple (size 15 mm x 50 mm) of approved make and quality as per direction of Engineer-in-charge. |
| 11 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. |
| 12 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 13 | Fixing glazed/ Ceramic Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3 mm thickness. |
| 14 | Deduct for not using 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) bedding in laying of floor tiles and jointing with grey cement slurry @ 3.3 kg/ sqm. |
| 15 | Providing and fixing on wall face unplasticised Rigid PVC SWR pipes conforming to IS : 13592 Type B, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes including all necessary specials and fiiting i.e bends, tees, junctions (with or without door) , reducers, WC connectors, couplers, cowels, clamps, hangers, rubber rings etc complete in all respect as per the directions of Engg-in-charge. |
| 16 | 75 mm diameter (Wall Thickness - 3.2 to 3.8 mm) |
| 17 | 110 mm diameter (Wall Thickness - 3.2 to 3.8 mm) |
| 18 | Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litre with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. |
| 19 | Providing and fixing PTMT/SS grating of approved quality and colour. |
| 20 | Circular/Squar type |
| 21 | 100 mm nominal dia |
| 22 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : |
| 23 | 15 mm nominal bore |
| 24 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall |
| 25 | 20 mm nominal outer dia Pipes |
| 26 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge . External work |
| 27 | 20 mm nominal dia Pipes |
| 28 | Extra for providing ISI marked Stainless Steel butt hinges instead of M.S. pressed butt hinges bright finished of required size with necessary screws. (Shutter area to be measured). |
| 29 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : |
| 30 | With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) |
| 31 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 32 | Hot finished welded type tubes |
| 33 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 34 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : |
| 35 | For fixed portion |
| 36 | Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 37 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) |
| 38 | Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 39 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. |
| 40 | Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side |
| 41 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). |
| 42 | Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment). |
| 43 | Providing and fixing Stainless Steel Kitchen Sink Unit made of AISI 304 (18/8) grade, comprising stainless steel sink bowl with integrated drain board, mounted over a rigid stainless steel frame structure of approved design. The unit shall consist of covered frame stand with bottom and intermediate racks/shelves for storage, made of stainless steel tubular sections, complete with necessary supports, legs, and anti-skid fittings. Including long nose/swan neck tap, stainless steel waste coupling 40 mm, flexible waste pipe, CP brass fittings, and connection with existing water supply and drainage line. The item includes fixing, alignment, testing, commissioning, and making good the surrounding area complete in all respects as directed by the Engineer-in-Charge.Overall size approx. 600 × 600 × 900mm (L × W × H). |
| 44 | Providing and fixing brass bib cock of approved quality : |
| 45 | 15 mm nominal bore |
| 46 | Providing and fixing PTMT/SS towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. |
| 47 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 48 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : |
| 49 | 100 mm inlet and 100 mm outlet |
| 50 | Sand cast iron S&S as per IS: 3989 |
| 51 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 52 | Providing and fixing PPR Unions |
| 53 | PPR Union 20mm |
| 54 | Providing and fixing uplasticised PVC connection pipe with brass unions : |
| 55 | 30 cm length |
| 56 | 15 mm nominal bore |
| 57 | Providing and fixing in position Liquied Soap Dispenser with glass bottle with necessary fitting arrangements, complete as per direction of the Engineer In Charge. |
| 58 | Providing and fixing square-mouth PVC gully trap of size 110 x 110 mm complete with brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design complete in all respect to complete Satisfaction of Engineer-in-charge:With Fly ash lime bricks (FALG Bricks) conforming to I.S. 12894. Astral/Supreme/Finolex or equalent make size 110 x 110 mm Cat no.M142003409 |
| 59 | Providing and fixing 50 mm thick mechanically sandwiched PUF Wall Panels of approved make comprising of Precoated Galvanised Iron Profile Sheets on both sides having 0.50 mm (+0.05%) total coated thickness (TCT) with zinc coating 120 grams per sqm as per IS: 277, in 240 MPA Steel Grade and finished with 18-20 micron colour coating of regular modified colour bond of approved quality over 5 micron priming coat on inner side of sheet, facing sheet profiled at 42 mm with pitch distance of 333 mm c/c or size, shape and pitch of corrugations as approved by Engineer-in-Charge, while lower side shall be slightly ribbed. The core between the outer profile sheet and the inner liner sheet shall be 50 mm CFC free close cell-95% high density rigid polyurethene foam 40+/-2 kg/cum. PUF Wall Panels should have protective guard film of minimum 25 micron to avoid scratches during transportation and should be supplied in single length upto 12 meter or as desired etc. all complete as per the directions of the Engineer-in-Charge. |
| 60 | Note: The sheet shall be fixed using self drilling/self tapping screws with EPDM seal, complete upto any pitch in horizontal/vertical or curved surfaces, excluding the cost of purlins, rafters and trusses etc. (which will be paid for seperately) including cutting to size and shape, wherever required |
| 61 | Providing and fixing SS tower bolts of approved make complete as per the direction of engineer in- charge with necessary ss screws etc. complete : |
| 62 | 200 mm high |
| 63 | 100 mm high |
| 64 | Providing and fixing Dead Lock of approved make with 55mm backset, 20mm square forend prepared for euro profile cylinder including strike plate. and EPC 60mm Length one side key operation other side thumb turn and Escutcheons in SS finish complete as per direction of Engineerin-charge with necessary S.S screws etc. complete. |
| 65 | Providing and fixing complete overhead shower set of approved make and quality, comprising square/rectangular stainless steel overhead rain shower (minimum 200 mm size), with wall mounted vertical sliding bar, adjustable hand shower with flexible hose (minimum 1.5 m long), diverter/mixer arrangement, and all necessary CP brass fittings.The item shall include chrome plated brass control valves, connection pipes, wall flanges, brackets, and fixing accessories, complete in all respects as per manufacturer’s specifications and as directed by Engineer-in-Charge.The shower system shall be finished in high quality chrome/plated/matte finish (as approved), including testing, commissioning, and making good the walls after installation. |
| 66 | Providing and fixing vanity type counter-top/under wash basin of approved quality and make standard size, White Vitreous China, suitable for mounting on vanity/counter, including 15 mm dia CP Brass single hole basin mixer, complete with all necessary fittings, connections, cutting and making good the walls/counter wherever required,waste pipe and finishing complete as per site requirement.(a) White/Grey Vitreous China counter-top wash basin (vanity type) of approved size and make, with 15 mm CP Brass single hole basin mixer. |
| 67 | Providing and laying ≈ 5 mm thick polyvinyl flooring sheet of approved make and shade, including surface preparation, cleaning, and leveling of the existing floor as required. The polyvinyl sheet shall be fixed using approved adhesive, ensuring uniform bonding and smooth finish. The adjoining joints shall be heated and fused using a gun-type welding tool, and all joints shall be sealed properly to achieve a seamless, durable, and hygienic surface. |
| 68 | The colour and pattern of the polyvinyl sheet shall be as approved by the user department or as per the direction of the Engineer-in-Charge. Complete in all respects, including labour, tools, adhesives, jointing material, and finishing, as directed. |
| 69 | Providing and Fixing of Glass PVC Film Providing and fixing high-quality PVC glass film on existing glass surfaces to regulate and reduce direct sunlight/ frosted view cutter ensuring improved visibility and better screen viewing conditions for project-based work. The film shall be of reputed make and shade, offering adequate light control, glare reduction, and UV protection. The work includes cleaning of glass surface, cutting the film to size, applying with approved adhesive, removing air bubbles, and finishing the surface smoothly with proper tools. All edges shall be neatly trimmed and pressed to ensure long-term adhesion. The shade and transparency level of the PVC film shall be as approved by the user or as directed by the Engineer-in-Charge. |
| 70 | Providing and fixing in position CP towel ring in polished chrome with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality Complete in all respects as per direction of the Engineer in charge. (Jaquar Cat No.AKP-CHR-35721P or approved equivalent) . |
| 71 | Providing and fixing in position Toilet roll holder with flap t with fixing accessories are complete in all respects as per direction of the Engineer in charge. Cat no AKP CHR 35735P or approved equivalent. |
| 72 | Providing and fixing in position Straight Grab Bar (Dia.38 mm Length 692mm Two Wall Horizontal and Swing Up Grab Bar complete with all accessories and fitting complete as per direction of the Engineer in Charge. |
| 73 | Providing and fixing health faucet (hand shower) of approved make and quality, comprising CP brass/ABS body with trigger, flexible stainless steel hose (minimum 1.0–1.2 m length), and wall hook/holder.The item includes all necessary fittings and accessories, complete in all respects, including fixing, testing, and commissioning, as directed by the Engineer-in-Charge. |
| 74 | Supplying and fixing of Roller Blinds to cover windows with fabric which can block 100% light and glare. Fabric: Max width 2.5 mtr, Composition:100% polyester, Weight 360 gsm, Openness factor 0%, light fastness 6-7 grade as approved by Engineer in charge. |
| 75 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 76 | Group A |
| 77 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. |
| 78 | 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 79 | 4 X 2.5 sq. mm + 2 X 2.5 sq. mm earth wire |
| 80 | Wiring for circuit/ submain wiring along with earth wirewith the following sizes of FRLS/HFFR PVC insulatedcopper conductor, single core cable in surface/recessed medium class PVC conduit as required. |
| 81 | 4 X 4 sq. mm + 2 X 4 sq. mm earth wire |
| 82 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 83 | Single pole |
| 84 | Supplying and fixing of following sizes of medium class PVC conduit/casing caping along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 85 | 25 mm |
| 86 | Providing and fixing following LED Down lighter (SMD Type) (System lumen efficacy ≥ 105 < 120 lm/Watt ) of following bodymaterials. Powder coated die cast /Extruded aluminiumBody including trim with Aluminium Reflector |
| 87 | Providing and fixing 300 mm exhaust with complete installation and commissioning |
| 88 | Supplying and fixing following rating, four pole, (threephase and neutral), 415 volts, residual current circuitbreaker (RCCB), having a sensitivity current 30 mA inthe existing MCB DB complete with connections,testing and commissioning etc. as required. |
| 89 | 63 A TP&N |
| 90 | Supplying and fixing following rating, four pole, 415 V,isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 91 | Supplying and Fixing Following way Single Pole and neutral,sheet steel,MCB distribution Board, 240V on surface/recess,complete with tinned copper bus bar,neutral bus bar,din bar,interconnections,powder painted including earthing etc.as required.(But without MCB/RCCB/Isolator) |
| 92 | 6 way (4 + 18), Double door Please Enable Macros to View BoQ information |
