|
| 1 | Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed. |
| 2 | Cleaning the concrete surface by removing dirt and debris, marking defective locations and removing loose concrete by careful stripping untill hard surface is exposed, cutting the concrete to regular shape, wire brushing the exposed surface and removing debris from site complete as per direction of the Engineer - in - Charge. |
| 3 | Cleaning the exposed reinforcement preferably upto full diameter by wire brush, applying two coats of polymer based rust removing compound left for 24 hours, removing the coating and then applying two (2) coats of polymer modified anti corrosive protective coating formulated to inhibit the corrosion of reinforcement as per manufacturer's specification] [Mode of measurement:The affected surface area of reinforcement shall be considered for payment] |
| 4 | Applying 2 coats of Non-Toxic Acrylic Polymer modified Paint having adhesive & waterproofing properties by mixing in proportion (1 liquid: 4 cementitious material) or as per manufacturer's specification for water proofing layer in water tank etc. (No Departmental Cement is required) |
| 5 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed andraking out joints including throating, nosing and drip course, scaffolding/staging where necessary.With 1:6 cement mortar 20 mm thick plaster1st Floor |
| 6 | 2nd Floor |
| 7 | With 1:4 cement mortar10 mm thick plaster1st Floor |
| 8 | 2nd Floor |
| 9 | Cleaning the walls and ceiling by scraping, sand papering and smoothening down the surface including putting. |
| 10 | Rendering the surface of walls and ceiling with white cement based wall putty of approved make and brand(1.5mm thick) |
| 11 | Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receiveDistemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC. (In Ground Floor)Solvent based interior grade Acrylic Primer |
| 12 | Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) :(Two coats)Luxury Quality |
| 13 | M.S. structural works in columns, beams etc. with simple rolled structural members (e.g. joists, angle, channel sections conforming to IS:226, IS:808 & SP(6)-1964 connected to on another with bracket, gussets, cleats as per design, direction of Engineer-in-charge complete including cutting to requisite shape and length, fabrication with necessary bolting, metalarc welding conforming to IS:816-1969 & IS:1995 using electrodes of approved make and brand conforming to IS:814-2004, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hirechargeo fall tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc. For structural members of specified sections weighing less than 22.5 Kg./m. |
| 14 | Welding in M.S. structural work with gas or electric: Continuous weld. |
| 15 | Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sandpapering etc |
| 16 | Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc |
| 17 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessaryOn timber or plastered surface :With super gloss (hi-gloss) -Two coats (with any shade except white) |
| 18 | On steel or other metal surface :With super gloss (hi-gloss) -Two coats (with any shade except white) |
| 19 | Labour for shifting the materialUnskilled LabourMazdoor (Male) |
| 20 | GST @18% from Item No. 1 to 15. |
| 21 | Labour Welfare Cess @1% from Item No. 1 to 16. Please Enable Macros to View BoQ information |
