|
| 1 | SUPPLY & FIXING OF PUSH CHAIR Functions: Developing the strength of upper limbs, chest and muscle groups of shoulder and back, improving the flexibility and stability of shoulder joints and elbows. Good for healing the bending and stretching hindrances of shoulder joints and elbows, muscular atrophy, frozen shoulder, tennis elbows, etc.Approaches Sit down with your back against the equipment and take hold of the handgrips with both hands and push forward with effort till your arms extend straight. Revert slowly.Size:-2265x662x2010 mm Material: Pre Galvanized Mild Steel, Material Thickness: 3 mm.Paint: All Weather Double Layer Powder Coated Paint Sealed Ball Bearing, Steel Seats for long lasting life |
| 2 | SUPPLY & FIXING OF SUR BOARD FUNCTIONS: By swinging both legs together from side to side the Surfing Board strengthens and develops the lower abdomen hips and thighs, improves balance and co-ordination through “core” activation Approaches: Stand on the pedals and grasp the handles with both hands, swing from left to right. Size:-1020x800x1480 mmMaterial: Pre Galvanized Mild Steel, Material Thickness: 3 mm.Paint: All Weather Double Layer Powder Coated Paint Sealed Ball Bearing, Steel Footrest / Foot paddle for long lasting life |
| 3 | SUPPLY & FIXING OF SPACE WALKER All pipes should used in the equipments should be galvanised with 3mm thickness.Multi Colour Powder coating with polyster paints should be used on all the equipments.The foot pedal on all the equipments should be of aluminium only.The seats should be made of high quality plastic with colour scheme in yellow or orange.The high end bearings such as SKF/NBC must be used in all the equipments.1 Dimensions- 1730*450*1450mm2 Colour- customizable multi colour and complete powder coat3 Size of main tube-114*3.75mm steel pipe4 Size of supporting tube-76*3mm steel pipe5 There is restrainer inside, the distance between swing arm and main tube is greater than 230mm avoiding the danger if getting struck..6 Al alloy protecting covers are used at the top other main tubes to protect from the rainwater7 Anti-skid components are used at the pedal parts.8 The distance between two pedals spinners is no less than 230mm, avoiding the damage of being struck.9 Anti theft cover is made by stainless steel/high quality plastic10 The minimum height of the edge of swing component is not less than 80mm11 Hazardous materials like coating agent, rubber are under national newest standard.12 Radius of edge is no less than 3.0 mm.13 The diameter of rotating shaft is not less than40mmFunctions: The Leg & Thigh Exerciser provides excellent cardiovascular exercise while developing the leg muscles. Allows a full range of movement in the hip joint improving flexibility and strength, without any impact or stress to joints and back. Suitable for all ages. Approaches: Hold the crossbeam with both hands and swing your legs backwards and forwards in a walking motion. |
| 4 | SUPPLY & FIXING OF SEATED PEDAL TRAINER – LEG SHAPER complete in all respects having following specifications.All pipes should used in the equipments should be galvanised with 3mm thickness.Multi Colour Powder coating with polyster paints should be used on all the equipments.The foot pedal on all the equipments should be of aluminium only.The seats should be made of high quality plastic with colour scheme in yellow or orange.The high end bearings such as SKF/NBC must be used in all the equipments.1 Dimensions- 1730*450*1450mm2 Colour- customizable multi colour and complete powder coat3 Size of main tube-114*3.75mm steel pipe4 Size of supporting tube-76*3mm steel pipe5 There is restrainer inside, the distance between swing arm and main tube is greater than 230mm avoiding the danger of getting stuck.6 Al alloy protecting covers are used at the top other main tubes to protect from the rainwater7 Anti-skid components are used at the pedal parts.8 The distance between two spinners is no less than 230mm, avoiding the damage of being stuck9 Anti theft cover is made by stainless steel/high quality plastic.10 Thickness of bearing bracket is no less than8mm11 Hazardous materials like coating agent, rubber are under national newest standard.Functions: Develops the strength of lower limbs, and improves the stability and agility of three main joints of lower limbs; good for the healing of inconvenience of bending and stretching of lower limbs, and muscular atrophy of lower limbs, rheumatoid arthritis, sciatica, sprain of the anklebone, etc. Approaches: Sit on the chair and step on the footboard. Stretching legs with force and recover slowly. Repeat. Users: Suitable for people of different ages. |
| 5 | SUPPLY & FIXING OF WAB BOARD WAB BOARD complete in all respects having following specifications.All pipes should used in the equipments should be galvanised with 3mm thickness.Multi Colour Powder coating with polyster paints should be used on all the equipments.The high end bearings such as SKF/NBC must be used in all the equipments.Wab Board or Abbs Shaper Size:-972x980x462 mm Two Wab Boards are raised on the pendulum pillar for exercising and agility of the abdomen and muscles. Functions: Developing the strength and flexibility of lumbar and abdominal muscles consuming the fat in waist and abdomen, good for figure shaping and bodybuilding. |
| 6 | SUPPLY & FIXING OF PARALLEL BARS PARALLEL BARS complete in all respects having following specifications.All pipes should used in the equipments should be galvanised with 3mm thickness.Multi Colour Powder coating with polyster paints should be used on all the equipments.The high end bearings such as SKF/NBC must be used in all the equipments.Functions: Develops the strength of upper limbs, shoulder and chest, strengthening cardiac and pneumonic functions. Approaches: Hold the crossbars tight with your hands and lift yourself up, then using the strength of your arms to do the pull-up action. Repeat according to your physical conditions. Users: Suitable for middle-aged people and youths. Size:- 1970x542x1600 mm Material: Pre Galvanized Mild Steel, Material Thickness: 3 mm. Paint: All Weather Double Layer Powder Coated Paint complete in all respects to the entire satisfaction of the Engineer-in-Charge. |
| 7 | SUPPLY & FIXING OF TAIJI WHEEL TAIJI WHEEL complete in all respects having following specifications.All pipes should used in the equipments should be galvanised with 3mm thickness.Multi Colour Powder coating with polyster paints should be used on all the equipments.The high end bearings such as SKF/NBC must be used in all the equipments.1 Dimensions- 1300*1050*1450mm2 Colour- customizable multi colour and complete powder coat3 Size of main tube-114*3.75mm steel tube4 Size of supporting tube-30*3mm steel tube5 Radius of edge is no less than 3.0 mm.6 Al alloy protecting covers are used at the top other main tubes to protect from the rainwater7 There are damping materials inside the rotating parts.8 The distance between two spinners is no less than 230mm, avoiding the damage of being stuck9 Anti theft cover is made by hard plasticFunctions: Develops the strength of upper limbs, shoulder and chest, strengthening cardiac and pneumonic functions. Approaches: Hold the crossbars tight with your hands and lift yourself up, then using the strength of your arms to do the pull-up action. Repeat according to your physical conditions. Users: Suitable for middle-aged people and youths. |
| 8 | SUPPLY & FIXING OF RIDING TRAINER RIDING TRAINER complete in all respects having following specifications.All pipes should used in the equipments should be galvanised with 3mm thickness.Multi Colour Powder coating with polyster paints should be used on all the equipments.The foot pedal on all the equipments should be of aluminium only.The seats should be made of high quality plastic with colour scheme in yellow or orange.The high end bearings such as SKF/NBC must be used in all the equipments.1 Circular mounted base pipe which has diameter 233mm and thickness is 8mm. There are 4 holes on this part at 90 degrees which PCD is 170mm. hole diameter is 20mm2 On this circular mounted base plate on the centre pillar is welded. Diameter of the centre pipe pillar is 114mm and height is 500mm3 A support pipe which is welded from the distance of base plate is 441mm and on this side of support pipe welded with the centre pillar and second one side is welded on the seat pipe rest Band4 Rest band is welded on the center pillar at the distance 265mm from the base plate vertically. This rest band has three parts- first short length 180mm, Second radius 150mm and the last is the long straight length270mm.5 A seat base pipe has 2 parts, first short length272mm, straight length, second long straight length 255m. A bush is welded on the short length and a screw (steel) is in between the brackets as they give up-down motion. Brackets are welded 105mm from the edge of the short length of the seat base pipe. Those brackets are 50mm apart from each other.6 On the centre pillar, two rectangular pipes are welded angularly at an angle 53mm from the centre pillar. The rectangular pipes are of the dimensions- length 373mm, breadth 50mm and height 29mm having 360mm vertically upwards from the mounting plate.7 A round shape pipe is welded on the top of the edges of the rectangular pipe and which length is 125mm and diameter 32 on both sides.8 A handle beam whose length 930mm,dia meter 60mm.bracket 1st is welded 140mm from the bottom edge of the handle and bracket 2nd is welded 280mm from the bottom edge of the handle beam. The round pipe is connected with the bracket 2nd with the help other steel screws.Functions: The Body Shaper gives a full-body cardiovascular and toning work-out, pushing with the legs while pulling with the arms against resistance. Works arms shoulders, back legs, abdomen and legs with low impact exercise.Approaches: Sit on the seat, hold the handles with both hands and put both feet on the pedals. Push with legs and pull on the handles. When exercising, keep your body upright. |
| 9 | Installation of outdoor gym in cement concrete block of size 5’X5’X1 ¼ ’ the entire satisfaction of engineer in charge. |
| 10 | Multi Activity Play System SPECIFICATIONS:- Qty1. SQ Deck 7’-0” H WITH CANOPY 12. SQ Deck 5’-0” H WITH CANOPY 13. SQ Deck 3’-0” H WITH CANOPY 14. SQ Deck 4’-0” x 4’-0” WITH 3’-0” HT 15 STRAIGHT INCLINED BRIDGE 4’-0” LONG 16 SWING BRIDGE 8’-0” LONG 17 SPIRAL SLIDE 5’-0” HT 18 DOUBLE WAVE SLIDE 7’-0” HT. 19 CROSS STAIRS 5’-0” HT 110 LADDER 7’-0” HT 111 TRIANGULAR STAIRS 3’ HT 112 SPLIT LEVEL LADDER 113 DOUBLE WAVE SLIDE 3’-0 HT 114 EXPANSION LADDER 7’-0” & 3’-0” 17. BRIEF DESCRIPTIONS/SIZES OF DIFFERENT COMPONENTS OFMULTIPLAY SYSTEMS:-I. Square deck of size 4'-0\\" X 4'-0\\":- The size of Sq. deck shall be 4'-0\\" X 4'-0\\". The vertical supporting pipes shall be/of minimum size 80 NB G.I. pipes or as required with Nylon Roof clamps attached to its. The Horizontal supporting members shall be of M.S. angle of minimum size 40X40X5 mm or as required. The platform of the ladder shall be of aluminum chequred plate of minimum thickness 16 SWG or as required.II canopy: - The canopy over square deck shall be made in two layers of Fiber Reinforced Plastic with minimum thickness of 3 mm and the same shall be supported on structural framework of M.S. Square pipe. The layers of ISO Gel coat shall be applied over canopy and two extra layers on the flange. The colour, design and finish of the outer surface of the canopy shall be as approved by Engineer-in-charge.III Double wave slide 3'-0\\" Ht.:- This shall be made of FRP having minimum shall thickness of 04 mm . The Backside of the slide surface shall be Mat finished. The layers of tooling Gelcoat shall be applied to the slide to give smooth finish. The supporting frame of the slide shall be made from G.. Pipe/ of minimum size 25 NBV. The pipes shall be powder coated. IV Double wale slide 7'-0\\" Ht.:- This shall be made of FRP having minimum shell thickness of 4 mm. The backside of the slide surface shall be Mat finished. 5 layers of tooling Gelcoat shall be applied to the slide to give it smooth finish. The supporting frame shall be made from G.I. Pipe of minimum size 25 NB. The pipes shall be powder coated. Additional ‘H’ type support shall be provided in the center.V Spiral Slide 5'0: - The spiral slide chute shall be made of FRP having minimum shell thickness of 4 mm and the same shall be supported on center support of G.I pipe having minimum size of 80 NB. The backside of the side surface shall be MAT. 5 layers of tooling Gelcoat shall be applied to the slide to give it smooth finish.The landing module shall be coated on G.I Pipe minimum 20 NB. Powder coated G.I Pipes with with nylon clamps attached to it.VI Pipe ladder the pipe ladder shall be made of powder coated G.I Pipe minimum size 25 NB. VII Arch entry railing: - The frame of the Arch entry railing shall be made of powder coated GI pipe of minimum size 25 NB and the same shall be supported with 25 NB powder coated G.I pipes. Nylon clamps are attached to the vertical pipe support of 80 NB pipe.VIII Straight railing:- The straight railing shall be made of horizontal pipe of size 25 NB and vertical pipes of 20 NB.IX Straight Bridge:- It shall be made of 25 mm thick wooden planks of shesham or Sal wood having 150 mm width an 810 mm length. The wooden planks shall be attached together with the help of nuts and bolts and shall be suspended with 8 mm thick galvanized chains. The railing shall be made of powder coated pipe supported of 20 NB GI Pipe. Please Enable Macros to View BoQ information |
