Tender For Creation Of Co-Working Space By Converting 06 Nos Industrial Shed Into Office Space To Augment The Existing Infrastructure At Joginder Nagar Industrial Estate Under Holistic Development Of Gni Project., Nicobars-Andaman And Nicobar Islands

TDR : 55673977

Tender Notice
BOQ

8 Days Left

Nicobars , Andaman And Nicobar Islands

Tender Brief : Tender For Creation Of Co-Working Space By Converting 06 Nos Industrial Shed Into Office Space To Augment The Existing Infrastructure At Joginder Nagar Industrial Estate Under Holistic Development Of Gni Project.

Document Fees
Refer document

EMD
₹ 795163.0 /-

Tender Value
₹ 3.97 Crore /-

Submission Date
04-06-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge.
2	All kinds of soil
3	Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.
4	All kinds of soil.
5	Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift.
6	Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.
7	Felling trees of the girth (measured at a height of 1 m above ground level), including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material.
8	Beyond 30 cm girth upto and including 60 cm girth
9	Beyond 60 cm girth upto and including 120 cm girth
10	Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :
11	1:1.5:3 (1 Cement: 1.5 coarse sand (zone-Ill) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
12	1:2:4 (1 cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)
13	1:3:6 (1 Cement : 3 coarse sand (zone-Ill) derived from natural sources : 6 graded stone aggregate 40 mm nominal size derived from natural sources)
14	1:4:8 (1 Cement : 4 coarse sand (zone-Ill) derived from natural sources: 8 graded stone aggregate 40 mm nominal size derived from natural sources)
15	Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-Ill) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.
16	Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :
17	1:1.5:3(1 cement: 1.5 coarse sand (zone-Ill) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
18	Centering and shuttering including strutting, propping etc. and removal of form for
19	Foundations, footings, bases of columns, etc. for mass concrete
20	Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.
21	Lintels, beams, plinth beams, girders, bressumers and cantilevers
22	Columns, Pillars, Piers, Abutments, Posts and Struts
23	Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.
24	Thermo-Mechanically Treated bars of grade Fe-500D or more.
25	Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3(1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.
26	Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25 mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete:
27	20 mm dia
28	Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.
29	Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: Note :- Aluminum hinges shall not be used in wooden shutters, stainless steel hinges shall be preferred.
30	100x75x4 mm
31	Providing and fixing aluminium slidings, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :
32	250x16mm
33	Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :
34	125 mm
35	Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.
36	Twin rubber stopper
37	Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and lnline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for (i) Sites with basic wind speed > 45 m/sec as per IS 875 — Part 3 (ii) Sites with structure height more than 20m for all wind speeds.Fixed window/ ventilator without mullion /transom.
38	Using R1 series with frame (33 mm & above) x (35 mm & above). (Height upto 0.90 metre)
39	Casement window double panels with fixed mullion with S.S. 304 friction hinges as per size and weight of sash, multi-point locking system, zinc alloy (zamak) powder coated handles.
40	Using R2 series with frame (39 mm & above) x (39 mm & above) & sash (39 mm & above) x (60 mm & above) & mullion (39 mm & above) x (60 mm & above). (Height upto 1.2 metre).
41	Casement door single panel with zinc alloy (zamak) 3D hinges, multi-point locking system with cylinder, zinc alloy (zamak) powder coated handles on both sides.
42	Using R3 series with frame (55 mm & above) x (50 mm & above) & sash (55 mm & above) x (85 mm & above) (Height upto 2.5 metre).
43	Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
44	Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
45	Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.
46	Electric resistance or induction butt welded tubes
47	Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.
48	Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with:
49	4.0 mm thick glass panes
50	Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.
51	40 mm thick with 20 mm nominal size stone aggregate
52	Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).
53	Medium shade pigment using 50% white cement 50% Grey cement
54	Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.
55	Providing and laying vitrified floor tiles in diferent sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.
56	Size of Tile 600x600 mm
57	Providing and laying Vitrified tiles in diferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.
58	Size of Tile 600x600 mm
59	Providing and fixing plain multipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately).
60	6 mm thick Cement fiber board, Type-B, Category-III as per IS: 14862 :2000
61	Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.
62	Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :
63	Ridges plain (500- 600mm)
64	12 mm cement plaster of mix:
65	1:4(1 cement: 4 fine sand)
66	Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour:
67	New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre
68	Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:
69	New work (Two or more coats applied @ 1.43 Itr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)
70	Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :
71	Two or more coats on new work
72	Repair to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sqm and under, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-In-Charge.
73	Hacking of CC flooring including cleaning for surface etc. complete as per direction of the Engineer-in-Charge.
74	Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.
75	Nominal concrete 1:3:6 or richer mix (including equivalent design mix)
76	Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :
77	Of area 3 sq. metres and below
78	Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of:
79	G.S. Sheet
80	Providing and filling in position rubberized bitumen hot sealing compound for sealing of expansion joints in roads / pavements all complete as per direction of the Engineer-in-Charge.
81	Providing and filling in position rubberized bitumen hot sealing compound for sealing of expansion joints in roads / pavements all complete as per direction of the Engineer-in-Charge.
82	Painting road surface marking with adequate nos of coats to give uniform finish with ready mixed road marking paint conforming to IS : 164, on bituminous surface in white/yellow shade, including cleaning the surface of all dirt, scales, oil, grease and foreign material etc. complete.
83	New work (Two or more coats)
84	Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :
85	W.C. pan with ISI marked white solid plastic seat and lid
86	Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:
87	White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap
88	Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink without drain board
89	470x420 mm bowl depth 178 mm
90	Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Semi rigid pipe
91	40 mm dia
92	Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
93	Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.
94	Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.
95	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall
96	20 mm nominal dia Pipes
97	25 mm nominal dia Pipes
98	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.
99	15 mm nominal dia Pipes
100	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work
101	40 mm nominal dia Pipes
102	Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :
103	25 to 40 mm nominal bore
104	50 to 80 mm nominal bore
105	Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :
106	25 mm nominal bore
107	40 mm nominal bore
108	Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
109	Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :
110	15 mm nominal bore
111	Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.
112	15 mm nominal bore
113	Providing and fixing PTMT grating of approved quality and colour.Circular type
114	100 mm nominal dia
115	Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball.
116	25 mm nominal bore, 152 mm long, weighing not less than 440 gms
117	Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements, weighing not less than 106 gms.
118	Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour.
119	15 mm nominal bore with 45 cm length
120	Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour.
121	25 mm nominal bore, weighing not less than 62 gms
122	Constructing soak pit 1.20x1.20x1.20 m filled with brick bats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design.
123	Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portion
124	Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)
125	Powder coated aluminium (minimum thickness of powder coating 50 micron)
126	For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)
127	Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)
128	Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately).
129	Providing and fixing 6 mm dia. G.I. level adjusting hangers (upto 1200 mm length), fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40x3 mm size 60 mm long and stainless steel expandable dash fastener of 12.5 mm dia and 50 mm long, complete as per direction of Engineer- in-charge.
130	Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment).
131	Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/ kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately)
132	18 mm thick
133	Providing and laying in position upto floor five level precast hollow cement concrete block walling 200 mm thick consisting of hollow blocks of size 400x200x200 mm in 1:3:6 (1 Cement : 3 coarse sand(zone-III) derived from natural sources : 6 graded stone aggregate 10 mm nominal siz derived from natural sources) including hoisting and setting in position with cement mortar 1:6 (1 cement : 6 coarse sand) complete
134	Providing and fixing glazing in uPVC door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge
135	With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)
136	Providing and fixing 15mm single exturded multi chamfered UPVC wall panel having wall thickness of 2.0-2.2 mm woth RoHS compliant lead free material of required size with moulded/ extruded bending with appropriate design, shape and size per manufacturers specification (to secure the panel insert tight in place within the style and rails of shutters/ fixed partition frame) matching the colour and shade of shutter/fixed partition frame (non decorative type).
137	Providing and fixing Eaves or Facia board with 18mm thick 30 cm wide wood polymer composite (WPC) board with nuts, washer and bolts all complete as per direction of Engineer-in-charge.
138	Extra for providing and fixing wind ties of 40x6mm flat aluminium section with necessary screws etc.
139	Providing cement concrete surface drain of size 23 x 23 cm in cement concrete 1:3:6 (1 Cement : 3 coarse sand(zone-III) derived from natural sources : 6 graded stone aggregate 12.5 mm and down siz derived from natural sources) including earth work in excavation, centering and shuttering, bed concrete of CC 1:4:8 and plastering with 12 mm thick cement plaster in 1:4 and neat cement punning of exposed surface complete
140	Providing and fixing uPVC (SWR) soil, waste and vent pipes as per IS : 13592 (Type - A) 2.5 kg/sqcm
141	110 mm dia
142	75 mm dia
143	Providing and fixing uPVC (SWR) plain bend of required degree with rings as per IS : 14735
144	110 mm dia
145	75 mm dia
146	Providing and fixing uPVC (SWR) single equal plain junction of required degree with rings as per IS : 14735
147	110 x 110 x 110 mm
148	Providing and fixing uPVC (SWR) bend of required degree with access door, rings and caps as per IS : 14735
149	75 mm dia
150	Constructing CC hollow block masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :
151	with cement concrete hollow block of size 400 x 200 x 200 mm in 1:3:6 ((1 Cement : 3 coarse sand(zone-III) derived from natural sources : 6 graded stone aggregate 10 mm nominal size derived from natural sources)
152	Providing and fixing PVC septic tank in position including excavation of soil upto required depth with inlet and end out let PVC 100 mm dia PVC vent pipe with all necessary fitting as per the direction of engineer in charge.
153	a) 50 Users PVC tank.
154	Providing and fixing health fauset including CP flexible pipe 1.00 mtr long with all fittings all complete as per the direction of Engineer-in-Charge.
155	Providing and fixing uPVC Terminal guard (Cowl) 110 mm dia as per IS : 14735 of approved make, colour & quality complete
156	Providing and fixing uPVC (SWR) Nahani trap with 110 mm inlet & 75 mm outlet of approved quality, colour & make including cost of cutting and making good the walls and floor complete
157	Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain white color board for partitions, wall panels, backing of cup boards and bathroom/kitchen cabinets etc. of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/ mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel screws etc. all as per direction of Engineer-In- Charge.
158	12 mm thick
159	Providing and fixing CPVC Gate valve (in SDR 11) of approved quality, colour & make with compact long handle (treaded) complete
160	25 mm nominal bore
161	40 mm nominal bore
162	Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete.
163	Providing cement concrete surface drain including earth excavation 10 cm thick base concrete and 15 cm thick side walling with 1:3:6 cement concrete ( 1: cement; 3 sand; 6: graded stone stone aggregate 40mm nominal size) cement concrete fininshing with 1:4 cement mortar (1 coment: 4 sand) cement plaster including floating coat of neat cement inside the drain surface including disposal of surplus earth work complete.
164	15 x15cm
165	Supplying and filling in plinth with Pulverised sand under floors, including watering, ramming, consolidating and dressing complete.
166	Providing and fixing PVC weep hole cutting placing in posistion as per directed by Engineer-in-charge.
167	PVC Pipe 50mm dia
168	Supplying Executive Office table of size 1500(W) X 750(D) X 750(H) having 3 Drawer on One side & One Shutter other side with top Drawer having Lock. MODEL No. ACDOT1507503D1S of SPACEWOOD (Buro Desking) or equivalent including fixing and installation complete.
169	Supplying storage pedestal of size 406(W)X450(D)X680(H) having 2 Book Drawer 1File Drawer MODEL No. ED3DPED of SPACEWOOD (Buro Desking) or equivalent including fixing and installation complete.
170	Supplying Mid height storage of size 900(W)x450(D)x1200(H) having 2 Door Storage MODEL No. MDMST900120 of SPACEWOOD (Buro Desking) or equivalent including fixing and installation complete.
171	Supplying multi seater conference table of outer size 6300 (L) x 2000 (W) x 750 (H) MODEL :- Z-LINE MULTI-SEATER CONFERENCE TABLE of SPACEWOOD (Buro Desking) or equivalent including fixing and installation complete.
172	Supplying Executive Office Chair High Back MODEL No. ALTO HB CHAIR of ARBITERR Brand or equivalent including installation complete.
173	Supplying Office Chair Medium Back MODEL No. ALTO MB CHAIR of ARBITERR Brand or equivalent including installation complete.
174	Supplying Office Chair MODEL No. C 114 VC of ARBITERR Brand or equivalent including installation complete.
175	Suuplying & installation of window curtain with premium curtain cloth of size 1500 x 1500 mm (02 pieces for each window) including stitching & accessories all complete as per the selection of branded cloth material and direction of Engineer in charge.
176	Supplying Twin seater premium sofa set of approved design, cloth, cushion complete as per the direction of Engineer in charge.
177	Supplying Teapoy Table of approved brand and manufacture as per the direction of Engineer in charge complete.
178	Supplying Floor rug for Teapoy table of approved design and material as per the direction of Engineer in charge complete.
179	Supplying Water purifier having 8L storage capacity, wall mounted : RO+UF+TDS Control + UV in Tank MODEL :- KENT Pride Plus of KENT Brand or equivalent including fixing and installation with all accessories complete.
180	Supplying Water purifier having 20L storage capacity, Chiller-cum-Water Dispenser : RO+UF+TDS Control MODEL :- KENT Perk of KENT Brand or equivalent including fixing and installation with all accessories complete.
181	Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. a) Group Ca) Group C
182	Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
183	Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.
184	a) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire
185	b) 2 X 4 sq. mm + 1 X 4 sq. mm earth wire
186	c) 2 X 10 sq. mm + 1 X 6 sq. mm earth wire
187	Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required
188	a) 5/6 A switch
189	b) 3 pin 5/6 A socket outlet
190	c) 15/16 A switch
191	d) 6 pin 15/16 A socket outlet
192	e) Bell push
193	Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.
194	a) 1 or 2 Module (75mmX75mm)
195	b) 3 Module (100mmX75mm)
196	c) 6 Module (200 mm x 75 mm)
197	d) 8 Module (125mmX125mm)
198	) 12 Module (200mmX150mm)
199	Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
200	Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.
201	Supplying and fixing brass batten/ angle holder including connection etc. as required.
202	Supplying and fixing call bell/ buzzer suitable for single phase,230 V, complete as required
203	Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.
204	Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.
205	Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
206	a) 8 way (4 + 24), Double door
207	Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.
208	a)Single pole
209	Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete, connections, testing and commissioning etc. as required.
210	a) 63 A
211	Providing and laying earth connection from earth electrode with 4.00 mm dia copper wire in 15 mm dia G.I. pipe from earth electrode including connection with copper thimble excavation and re-filling as required.
212	Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.
213	Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.
214	Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.
215	Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL/ DWC pipe as required.
216	a) Upto 35 sq. mm
217	Supplying and fixing cable route marker with 10 cm X 10 cm X 5mm thick G.I. plate with inscription there on, bolted /welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.
218	Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.
219	a) 63 mm dia (OD-63 mm & ID-51 mm nominal)
220	Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A \\"C\\" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with Connections, testing and commissioning etc. as required.
221	Supplying of following sizes of XLPE insulated armoured Aluminium conductor cable of 1.1 KV grade conforming to IS: 7098 (Part-I) and IS No. 1554 (Part-I) 1988 as applicable Make: CCI/ Gloster/ Havells/ Polycab/ Finolex as required as directed by Engineer-in-charge
222	a) 25 Sq.mm x 4 Core
223	Supplying of AC Ceiling Fan (1200 mm) Sweep with Socket Type Electronic regulator i/c wiring down rod of standard length (upto 30 cm) with all accessories etc., as required. Similar to make Crompton Empower 50 - 1 Star (ISI Marked) or its equivalent etc., as required as directed by Engineer-in-charge
224	Supply & installation of Suspended Surface-Mounted LED Tubelight Fitting similar to Philips SP570P LED265 6500 PSU W12L120 OD SI comprising high efficiency LED driver (230V AC, constant current), LED tubes integrated, complete with all necessary accessories, mounting hooks/ropes/rigid brackets, complete with internal wiring, suspension arrangement and connection to existing lighting circuit as per technical specifications and manufacturer’s recommendations. Includes testing, commissioning, and necessary supports.
225	Supply and installation of IP65 Vistaglow impact-resistant wall-mounted bulkhead LED fitting 10W similar to Philips WT140W LED7S CW PSU S1 PC suitable for outdoor, with high efficiency LED module & driver, complete with all required accessories, wall mounting brackets, gland, internal wiring, connection to existing power supply and testing & commissioning.
226	Supplying and Fixing of LED Lamp 10W B22 of Make:Havells LED Adore10W or similar etc., as required for Batten Holder as directed by Engineer-in-charge
227	Supplying and Fixing of exhaust fan 200 mm sweep Light Duty Make:- Havells Smart Ventilair White Colour or similar etc complete with all accessories etc. asdirected by Engineer-in-charge
228	Supplying and fixing of SMC Sintex box of inside dimension 350 mm x 250mm x 138 mm for accommodating LT 3 Phase KWh meter with cut out similar to Code No. GSJB-3425, etc or equivalent make as required and directed by Engineer-in-charge
229	SITC of 2 Ton 5 Star as per latest rating of BEE High Wall Mounted Inverter Split Type Air Conditioner unit complete with indoor unit (IDU), outdoor unit (ODU) single phase 230V ± 10% with R32/R410A refrigerant, copper condenser coil and Rotary compressor i/c providing required length of refrigerant copper pipe of std. size as per recommendation of manufacturer of Air Conditioner with insulation, cordless remote control, cutting and drilling holes on the wall with smooth finish etc as required Similar to make Hitachi Model No.2.0TR CLASS HITACHI YOSHI 5400FXL FROST WASH INVERTER - R32 - RAS G522PCAISF - 5 STAR or its equivalent as per the direction of Engineer-In-Charge.
230	SITC of 1.5Ton 5 Star as per latest rating of BEE High Wall Mounted Inverter Split Type Air Conditioner unit complete with indoor unit (IDU), outdoor unit (ODU) single phase 230V ± 10% with R32/R410A refrigerant, copper condenser coil and Rotary compressor i/c providing required length of refrigerant copper pipe of std. size as per recommendation of manufacturer of Air Conditioner with insulation, cordless remote control, cutting and drilling holes on the wall with smooth finish etc as required Similar to make Hitachi Model No.1.5TR CLASS HITACHI INVERTER- R32 - RAS E518PCCIBWB- 5 STAR or its equivalent as per the direction of Engineer-In-Charge.
231	Supplying and Fixing of 5 KVA Voltage stabilizer suitable for 2.0 Ton Air Conditioner with working Voltage of 140V to 270V, Make: PREMIER ECO 5 DB or its equivalent as required.
232	Providing and fixing of Pre-fabricated stand for keeping outdoor units of 1.5 Ton/ 2.0 Ton capacity Split type AC etc. as required.
233	Supplying and fixing of Fire Extinguisher ABC Powder extinguisher (ISI marked 6 Kg) capacity brand Lifeguard or Equivalent , wall bracket fixing with suitable , screws etc. as reqd. ISI marked Confirming to ISI 15683:2016 along with Fire Fighting Equipment Certificate for Test and Warranty as required as directed by Engineer-in-charge
234	Supplying and fixing of ISI marked CO2 type Fire extinguisher of 4.5 Kg(catridge type) brand Lifeguard or Equivalent fitted with control valve and high pressure 1 mtr long discharge hose and horn complete with initial gas charge with carrying handle and wall mounting bracket, fixing with suitable, screws etc. Confirming to ISI 15683:2016 along with Fire Fighting Equipment Certificate for Test and Warranty as required as directed by Engineer-in-charge
235	Providing earthing with safe earthing electrode of galvanization 80 to 100 microns, length 2000mm, outer dia 50 mm, inner dia 19 mm and inner space be filled with crystalline conductive mixture including filling -up with electrolite (Back fill compound) as required for safe earth electrode and providing masonary enclosure with cover plate having locking arrangement etc. as required. (Ashlok)
236	Supplying and fixing extra down rod of 100 mm length G.I. pipe ,15 mm dia, heavy gauge suitable for ceiling fan installation including cutting drilling holes necessary nuts bolts complete to increase drop length of ceiling fan from ceiling including as required.
237	Supplying, Installation testing and commissioning of 8 Way 'G' frame Double Door Panel with incoming 1 No. 300A FP 25KA MCCB \\" LS\\" Frame , 6 No. 100A 25 KA FP MCCB as outgoing, set of cable alley , 400A FP add on incoming changeover switch with enclosure , Pre-wired Digital meter module with Voltmeter, Ammeter, Selector Switch, CT's Control fuse and indicating light etc. i/c connection complete and providing 1 No. 2mm thick Class A rubber floor mat of Size 1m x 2m as requiredG' Frame Panel Board, I, 8 way 4P Pole outgoing, double door, Conforms to IS: 8623, IEC:60439, Make: Havells Cat No. HLGF4000800 or equivalent n L&T.Incoming MCCB 300A 4Pole breaking capacity 25KA Frame LS, Conforms to IS/IEC:60947-2, Make: Havells Cat No. IHLLSEC40400 or equivalent in L&T. Spreader Terminal kit for 300A 4 Pole Make: Havells Cat No. ISSLLX0066Outgoing MCCB 100A 4Pole breaking capacity 27 KA Frame HID1, Conforms to IS/IEC:60947-2, Make: Havells Cat No.IHA13DB40100 or equivalent in L&T.Spreader Terminal kit for 100A 4 Pole Make: Havells Cat No. ISSLHX4279Cable alley for GF frame Panel board outgoing 4P Double door ,400A, 8 way, Conforms to IS: 8623, IEC:60439 Make: Havells Cat No. ISSBOU0701 or equivalent in L&T. Pre-Wired Meter Digital Module with Voltmeter, Ammeter, Selector Switch,
238	Ct’s Control Fuse & Indicating Lights similar to CAT No ISSBOU0707 or equivalent25 Sqmm HRFR PVC Copper multistrantd single core Cable for inter connection (6X8x0.5=24)+ 5% WastageInstallation of all accessories including lugs / compression gland etc 25 Sqmm Cu Lug( 6x8 =48 Nos ) + M12 Nut,Bolt& washer (=48 Nos)3mm Rubber Floor Mat of Size 1.00 mx 2.00 m suitable for Class - A upto 3.3KV
239	Supplying of following sizes of XLPE insulated armoured Aluminium conductor cable of 1.1 KV grade conforming to IS: 7098 (Part-I) and IS No. 1554 (Part-I) 1988 as applicable Make: CCI/ Gloster/ Havells/ Polycab/ Finolex as required as directed by Engineer-in-charge
240	a) 25 Sq.mm x 4 Core ( for 100 A Outgoing Feeder)
241	b) 50 Sq.mm x 4 Core ( for 320A Incoming Feeder from Transformer )
242	Supplying, Installation, Testing (Including Fuel,Lub Oil ,Coolant etc) and Commissioning of 125 KVA Diesel Generator Set with water Cooled, Electric Start Diesel Engine directly coupled with AC alternator 03 Phase, 415 Volts, 50 Hz @ 0.8 p.f, self excited, self regulated designed to run at 1500 rpm mounted on common base frame, control panel, integral fuel tank with Battery of suitable capacity and Leads and accessories in all respect with CPCB4+ approved , acoustic enclosure( sound proof) with inbuilt control panel including mannual/ Automatic Mains Failure Board (AMF) similar to Generator Set of Make Ashok Leyland Engine Model No. H6G4DE125 or its equivalent along with ATS Panel in sheet enclosure as suited i/c connections etc.,as required as directed by Engineer-in-charge
243	Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.
244	a) 1 run of cable
245	Supplying and fixing of following size of medium class PVC conduit along with accessories in surface/recess including the wall and making good the same in case of recessed conduit as required.
246	a) 25 mm
247	Supplying, installation, testing & Commissioning of NVR suitable for 16 channel IP camera input 2 MP, 3 MP,4 MP and 8 MP Network camera, 200 Mbps incoming band width with 2 SATA HDD code for each HDD support multi brand network cameras etc. complete as required. Make:CP PLUS -Model:-CP-UNR-4K2162-V2)or similar in make Dahua .
248	Supplying, installation, testing & Commisioning of IR Network Bullet Outdoor Camera, 4 Mp resolution, 2.8 mm, 4mm,6mm fixed lens, IR range 60m, IP67 protection, Make: CP PLUS Model:CP-UNC-TA41L5C-D-V3 or similar in make Dahua .
249	Supplying and installation of factory terminatred fiber optic patch cord of length 1m/2m(as Required) duplex or single mode (as required)suitable for 1Gbps/10Gbps optical network applications,factory polished and suitable for CCTV & NETWORK CONNECTIVITYAS DIRECTRED BY ENGINEER IN CHARGE.
250	Supplying, installation, testing and commissiong of 10 Port Power Over Ethernet switch for Cameras with 2 Uplink ports. Make:CP-PLUS Model: or similar in make Dahua .
251	Supplying and fixing of weatherproof PVC outdoor enclosure IP65 rated 4.5*4.5 \\" square box suitable for mounting on camera poles for cctv installationincluding necessary fixing clamps and labour
252	Supplying, installation, testing and Commissioning of 8 TB/6000 GB HDD Surveillance Hard Disk for video data backup storage in existing NVR rack etc. complete as required. Make: Seagate, Model: ST8000VE001or equivalent.
253	Supplying, installation, testing and commissioning of 43\\" full Ultra HD LED TV eith HDMI cable (10 Mtr) including all accessories such as remote control power cable for wall mounting etc. complete as required. Make: Samsung Neo series Ultra HD Smart LED TV UA43AUE65AKXXL(Black) or similar in make Sony/LG/PHILIPS.
254	Providing and fixing metal heavy duty black Wall mount stand suitable for 43\\" LED/LCD TV,including necessary accessories ,fixtures,levelling ,drilling of holes on wall surface and proper alighnment using anchor fasteners installing the TV safely on bracket ,testing for stabilityand cleaning debris complete as required.
255	Supplying andinstallatiopn of wall mount 2U Network rack suitable for CCTV NVR system,made of CRCA steel powder coated finish front glass door with lock, cable entry provision at top and bottom,mounting rails,including fixing the rack on wall using achor fasteners,proper alighnment ,testing complete as directed by engineer incharge.
256	Suplying and fixing of RJ45 LAN Modular Block CAT5 Connectorfor CCTV LAN connections,including proper stripping and cliping of Lan Cable conductors ,terminating using crimping tools testing for data continuity in allrespects as directed
257	Supplying & installation of Cordless Mouse Make :Dell WM118 Wire less mouse or Similar in lenova, HP .
258	Supplying and installation of 5A Power extender /Power strip with 4 universal soxkets suitable for NVR and assosiated networking equipment including plug top,internal wring ,surge protection to ensure proper functioning and continuos power supply.
259	Supplying, installation, testing & Commisioning of IR Network DOME indoor Camera, 4 Mp resolution, 2.8 mm, 4mm,6mm fixed lens, IR range 30m, IP67 protection, Make: CP PLUS Model:CP-UNC-DA41L3C-D-Q or similar in make Dahua .
260	Supplying ,Installation,testing of advanced Video conferencing system comprising of 65 inch UHD/4k LED disply panel with suitable wall mounting ,Bosch conference control unit,web conference cameras with required cabling and mounting accessories,wireless deligate microphone units (rechargeable type)with clear audio pickup and mute functions,Battery charging unit compactibel with wireless microphnes ,audio processor satellite speakers,power supply units,HDmi/USb/netrwork connectivity,all interconnections,configuration,integration with web conferencing platforms complete with all accessories connectors complete in all respects as per details below and as directed by Engineer in charge.MaterialsConference Controller unit : Model CCSE-CUCCS700 Make Bosch - 01.00 NoConference delegate Unit ; Model CCSE-DLCCs700 Make : Bosch - 16 NosConference Chairman Unit : model CCSE-CMLCCS700 Make : Bosch - 01.00 NoExtension Cable 10 Moxyfe and connector Male-Female & accessories- 02.00 NosDigital Sound Processor (DSP) Make :People link -01.00 NosAmplifier 180W Make: Bosch - 01.00 NoFloor Mount Rack 22-32 Fully Loaded Make : Netrack -01.00 NoSatellite Speakers Type 30W -06.00 nosVideo Conferencing Camera 12X Make: People link -01.00 NoDual Cordless Mic make : Studio Master -01.00 No65 Inch Interactive Panel Make: People Link -01.00 No Please Enable Macros to View BoQ information

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents
5	Click here to download tender document	Tender Documents

Also Visit

Tenders

Andaman And Nicobar Islands Tenders

Construction Tenders

Turnkey Projects Tenders

Infrastructure Work Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Creation Of Co-Working Space By Converting 06 Nos Industrial Shed Into Office Space To Augment The Existing Infrastructure At Joginder Nagar Industrial Estate Under Holistic Development Of Gni Project., Nicobars-Andaman And Nicobar Islands

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Creation Of Co-Working Space By Converting 06 Nos Industrial Shed Into Office Space To Augment The Existing Infrastructure At Joginder Nagar Industrial Estate Under Holistic Development Of Gni Project., Nicobars-Andaman And Nicobar Islands

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us