|
| 1 | Dismantling of floor hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed. |
| 2 | M&L for 10 to 12 mm thick vitrified parking tiles in approved shade from meteor series, area of each tile exceeding 0.08 Sqm but not exceeding 0.18 Sqm in floors etc., set and jointed in neat cement slurry and pointed in matching coloured polymer cement based grout to match over and including 15 mm thick Screed bed or bedding layer in CM 1:6, complete all as specified and directed. |
| 3 | M&L for 10 to 12 mm thick 3D exterior wall tiles in stone /bulging/ approved shade from meteor series/ matt finish as approved, area of each tile exceeding 0.08 Sqm but not exceeding 0.18 Sqm in floors etc., set and jointed in neat cement slurry and pointed in matching coloured polymer cement based grout to match over and including 10 mm thick Screed bed or bedding layer in CM 1:6, complete all as specified and directed. |
| 4 | M&L for 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and direction. |
| 5 | S&F coloured chequered cement concrete tiles size 300 mm x 300 mm x 22-25mm thick with grey cement and pigment , rubber moulded glossy finish, ISI marked, coloured, set jointed and pointed in neat cement slurry over and including 20mm thick screed bed in CM 1:6, complete all as specified and directed. |
| 6 | Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc., complete all as specified and directed. |
| 7 | M&L 15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4 and finishing even and smooth without using extra cement, complete all as specified and directed. |
| 8 | Preparation of new surface of wall and applying two coats of cement base paint over one coat of primer, complete all as specified and directed. |
| 9 | M&L for plain cement concrete, 1:2:4, type B-0 (using 12.5mm graded crushed stone aggregates), as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed. |
| 10 | Demolition of old PQC / concrete of any description and in any position not other wise specifically provided for and demolished material thrown out of premises complete all as specified and directed by Engineer-in-Charge |
| 11 | M&L for Hard core of broken stone gauge not exceeding 63mm deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surfaces, complete, all as specified and as directed. |
| 12 | M&L for 100mm thick plain cement concrete, 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base, complete all as specified and directed. |
| 13 | M&L for 50 micron thick HDPE Polythene film, laid on a coat of bitumen primer @ 0.30 to 0.50 Kg per Sqm, complete all as specified and directed. |
| 14 | M&L for plain quality concrete work in pavement / hard standing of flexural strength 40 kg / Sqcm2 in field using 400 kg of cement per cubic metre or as per design mix whichever is higher using non circular synthetic polyster triangular fibre @ 0.25% by weight of cement, thickness of concrete 20 cm, , complete all as specified and directed.Note:- (i) Unit rate quoted shall be inclussive steel formwork as required.(ii) Polyster triangular fibre shall be measured and paid as \\"Supply only\\" under respective Items of BOQ. |
| 15 | Add / deduct to Serial Item No 14.00 if extra / less Kg of cement is used for cubic metre, complete all as specified and directed. |
| 16 | Supply only polyster triangular fibres, complete all as specified. |
| 17 | M&L for forming 12mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’, thickness of slab 15cm, complete all as specified and directed. |
| 18 | M&L for forming contraction (Dummy) joint, 65mm deep x 10mm wide as the work proceeds in alternative ways and filled with sealing compound grade 'A' after priming with primer for grade 'A' sealing compound , complete all as specified and directed. |
| 19 | Demolition of cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness (below or above ground level) and removal the rubbish/ demolished material outside defence land, complete all as specified and as directed. |
| 20 | M&L for 75mm thick plain cement concrete, 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base, complete all as specified and directed. |
| 21 | M&L for factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3, including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required, including demolition of existing complete all as specified and directed. |
| 22 | M&L for applying two coats of terrakota paint on new concrete surface / kerb stone as approved, complete all as specified and directed. |
| 23 | Complete removal of existing treatment from Kerb stone surfaces including scraping down smoke soots, moulds, moss and trading oil and greasy spots etc including cornices, pilasters etc (Plastered or un plastered surfaces) over 10cm width or girth and applying two coats of terrakota paint as approved, complete all as specified and directed. |
| 24 | Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed. |
| 25 | M&L for brick work with sub-class `B' bricks (using old size bricks), straight or curved on plan exceeding 6m mean radius built in CM 1:6, Complete all as specified and directed. |
| 26 | M&L for plain cement concrete, 1:3:6, Type C-1 (using 20mm graded crushed stone aggregate) as in surface channel, drain and RCC post etc. including necessary form work, complete all as specified and as directed. |
| 27 | M&L for Extra over for forming fair finished to drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc., complete all as specified and directed. |
| 28 | S&F wall panelling / cladding of aluminium composite panel of any colour any type of approved shades made out of 3mm thick aluminium composite panel material consisting of 2mm thick mineral core sandwiched between two aluminium sheets (each 0.5mm thick). The aluminium composite panel wall panelling / cladding sheet shall be coil coated, with Kynar 500 based PVDF lumiflon based fluoropolyer resign coating of approved colour and shade on exposed face and polymer (service) coating on the face fixed over and including base frame fabricated with aluminium square pipe of size 25mm x 40mm with 1mm wall thickness including stainless steel screws, nuts bolts, washers cleats, weather silicone sealant for groove filling etc. complete all as per manufacturer instruction and as directed including taking down old panelling / cladding, complete all as specified and directed. |
| 29 | M&L for 20mm thick granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick screed bed in CM 1:4 and including demolition of existing stone slab and tiles, complete all as specified and directed. |
| 30 | Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed. |
| 31 | M&L for mild steel framed work such as ornamental and intricate design grills, gratings, gates etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, nosing, framework of water tanks, band, straps, wind ties and similar work conforming to Fe.290.Gde-E-165, complete all as specified and directed. |
| 32 | Preparation of old plastered /unplastered wall surfaces by washing down, brooming down, steel wire brushing and removing all grass, vegetation or shrubs from boundary wall/compound wall etc. and applying one coats cement base paint including scaffolding , complete all as specified and directed. |
| 33 | Supply only 400 micron thick polythene film |
| 34 | Supply only Fine aggregate (sand) |
| 35 | Supply only 20 to 40 mm Crushed Stone Aggregate |
| 36 | Supply only 40 to 63 mm Crushed Stone Aggregate |
| 37 | Supply only 63 to 90 mm Crushed Stone Aggregate |
| 38 | Supply only 150 to 300 mm Crushed Stone Aggregate |
| 39 | M&L for filling HDPE Sand bags khaki of size 30 cm x 30 cm x80 cm with sand and saw dust closing the open and with nylon wire complete alll as specified and directed by ENGR-IN- CHARGE . Sand bag of make DCPL or equivalent . |
| 40 | M&L for stacking seive fine sand in any shape and position as approved by Engineer-in-charge NOTE:- Rates of mixing of sand and saw dust in proportion as decided by Engineer in charge and lifting the mixture upto 6 m and laying in slope is inclusive in the rates. |
| 41 | M&L for stacking of SAW DUST in any shape and position as approved by Engineer-in-charge NOTE:- Rates of mixing of sand and saw dust in proportion as decided by Engineer in charge and lifting the mixture upto 6 m and laying in slope is inclusive in the rates. |
| 42 | Labour for extraction of existing mixture and seiving , lifting, laying, stacking and depositing the mixture , complete all as specified and directed by Engr-in- charge . |
| 43 | Deduction to be made from BOQ for Schedule 'A' Part-II (Credit Schedule from dismantling / taking down items) worth Rs 74,180.00 during AOC.(Note :- Tenderers shall not quote for this Schedule) Please Enable Macros to View BoQ information |
