Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge., All kinds of soil DSR 2023- 2.6.1 |
| 2 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :, 150 mm dia. R.C.C. pipe DSR 2023- 19.6.2 |
| 3 | Construction of Subgrade with Material Obtained from Borrow Pits (For Carted Earth Work) Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 10 Km. as per Technical Specification Clause 301.5, - MORD -301.5 (3.4) |
| 4 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- termite treatment (excluding the cost of chemical emulsion) :, Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor :, With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. DSR 2023- 2.35.3.1 |
| 5 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement, All works upto plinth level, Concrete of M25 grade with minimum cement content of 330 kg /cum DSR 2023- 5.33.1.1 |
| 6 | Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineer in-Charge., 80mm thick Cement concrete paver block of M-30 grade with approved colour, design & pattern. DSR 2023- 16.91.2 |
| 7 | Mild steel or iron work in plain work such as in R.C.C. or R.B. (when not included in an over all rates ) including bending for proper completion of the work and including supply of steel and its wastage , bends, hooks and authorised overlaps shall be measured up to floor two level. (SI No. 504) (Sanction Rate) - SI 504 |
| 8 | Structural steel work in single section, fixed with or without connecting plate,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete DSR 2023- 10.1 |
| 9 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete., Fixed to openings /wooden frames with rawl plugs screws etc. DSR 2023- 9.48.2 |
| 10 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :, 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources). DSR 2023- 4.1.8 |
| 11 | Centering and shuttering including strutting, propping etc. and removal of form for :, Centering and shuttering including strutting and propping and removal of items for: Foundations, footings, base of columns, etc DSR 2023/5.9.1 DSR 2023- 5.9.1 |
| 12 | Centering and shuttering including strutting, propping etc. and removal of form for :, Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers DSR 2023- 5.9.5 |
| 13 | Centering and shuttering including strutting, propping etc. and removal of form for :, Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick DSR 2023- 5.9.20 |
| 14 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc., up to floor five level, excluding the cost of centering, shuttering and finishing :, 1:1½:3 (1 cement : 1½ coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). DSR 2023- 4.2.2 |
| 15 | Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50 mm x 1.6 mm complete, all as per direction of Engineer-in-charge. DSR 2023- 23.9 |
| 16 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :, Cement mortar 1:6 (1 cement : 6 coarse sand) DSR 2023- 6.4.2 |
| 17 | Constructing masonry Chamber 120x120x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.l. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:1.5:3 mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design:, With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 DSR 2023- 18.35.1 |
| 18 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:, Cement mortar 1:6 (1 cement : 6 coarse sand) DSR 2023- 6.1.2 |
| 19 | Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 12.5mm nominal size derived from natural sources). DSR 2023- 4.10 |
| 20 | Providing and applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. DSR 2023- 4.13 |
| 21 | 12 mm cement plaster of mix :, 1:4 (1 cement: 4 coarse sand) DSR 2023- 13.4.1 |
| 22 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. DSR 2023- 13.80 |
| 23 | 12 mm cement plaster of mix :, 1:6 (1 cement: 6 coarse sand) DSR 2023- 13.4.2 |
| 24 | Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement., 12 mm cement plaster DSR 2023- 13.9.1 |
| 25 | Add for Plaster drip course/groove in plaster the all or in ceiling vertically or horizontally as required. - PSR..Plaster drip |
| 26 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete., Cement concrete flooring 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate DSR 2023- 11.3.1 |
| 27 | PWD 651 E&M 2018 Supply & fixing of 12.5 mtr High mast shaft of approved make with rising system hot dip glavanized inside & out side dip,heaving pole sheet thickness 3 mm. Top dia minium 150 mm, Bottom dia 310 mm base plate 25 mm thick suitable for wind velocity as per IS 875 part 3 & having no circumferential weld, with accessories for high mast such as head frame suitable for 6 luminaries & its control gear boxes 0.75 HP power tool moter, 3 point suspension system with steel wire rope 6 mm dia, double drum winch, including making suitable foundation as per manufature drawing/ site reuiment along with foundation bolts nuts, washers, anchor plates etc completee in all respect. - PWD 651 |
| 28 | 1454 PWD E&M 2018 Supply and fixing of factory wired integral LED flood light luminaires with die cast aluminium housing built with dirver set suitable for 140 to 150 Watt. Confirming to IP 66 protection complete in all respect. CAT-AA- 1454 PWD E&M 2018 |
| 29 | S/E of G.I. wire on 8 to 4 SWG on pole/service bracket including binding etc. complete in all respects SI.No. 628/18. |
| 30 | S/W of submain with two Nos. of 2.5 Sq.mm FRLSH PVC insulated 1100 V grade single core multistrand copper conductor cable in existing conduit complete with supply of all material Labour and T&P required for proper completion of the work as directed at site by E/I. SI. No. 289/18. |
| 31 | S/F of 40A TPN of Automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch TSO 100 series with contractors, HRC fuses, isolating switch metering instrument & instrument box with CTs etc, in case of TPN, complete in all respect as per direction of Engineer-in-charge. SI. No. 807/18 e(ii). |
| 32 | S/L of following cable \\"Al\\" conductor P.V.C. insulated armoured served sheathed cable 1100V grade at a depth of 750mm. Below ground level over a cushion of 75mm with DWC Pipe approved make UPPPCL as per direction of E/I. complete in all respects. 501/2018. Approved Makes:- Gloster/Polycab/KEI/SCI/Havells PWD SOR 501 10 sq. mm 4 core @327.00 |
| 33 | Supplying following 1.1kV grade, heavy duty XLPE insulated, FRLS type armoured /Unarmured cables suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath, outer sheath provided with FRLS insulation, galvanised steel armouring (round or flat as mentioned) and with all components as mentioned in BOQ, specifications and schedule, complete as required. - DSR 501 (h) 2018 |
| 34 | S/L of following cable \\"Al\\" conductor P.V.C. insulated armoured served sheathed cable 1100V grade at a depth of 750mm. Below ground level over a cushion of 75mm with DWC Pipe approved make UPPPCL as per direction of E/I. complete in all respects. 501/2018. Approved Makes:- Gloster/ Polycab/ KEI/ SCI/ Havells PWD SOR 501 |
| 35 | S/L of following cable \\"Al\\" conductor P.V.C. insulated armoured served sheathed cable 1100V grade at a depth of 750mm. Below ground level over a cushion of 75mm with DWC Pipe approved make UPPPCL as per direction of E/I. complete in all respects. 501/2018. Approved Makes:- Gloster/ Polycab/ KEI/ SCI/ Havells PWD SOR-2018 501 (b) 16 Sq.mm 4 Core |
| 36 | S/L of following cable \\"Al\\" conductor P.V.C. insulated armoured served sheathed cable 1100V grade at a depth of 750mm. Below ground level over a cushion of 75mm with DWC Pipe approved make UPPPCL as per direction of E/I. complete in all respects. 501/2018. Approved Makes:- Gloster/ Polycab/ KEI/ SCI/ Havells PWD SOR 501 (c) 70 Sq.mm 3.5 core |
| 37 | S/F of following size palm or pin type copper tin plated cable socket (Lug) to the cable lead insulating with tape and making connections complete in all respects as per direction of E/I.SI.No.504/SOR-18. (a) 25 sq.mm. |
| 38 | S/F of following size palm or pin type copper tin plated cable socket (Lug) to the cable lead insulating with tape and making connections complete in all respects as per direction of E/I.SI.No.504/SOR-18. (b) 50 sq.mm |
| 39 | S/F of following size palm or pin type copper tin plated cable socket (Lug) to the cable lead insulating with tape and making connections complete in all respects as per direction of E/I.SI.No.504/SOR-18. 16 sq. mm 4 core |
| 40 | S/F of following size palm or pin type copper tin plated cable socket (Lug) to the cable lead insulating with tape and making connections complete in all respects as per direction of E/I.SI.No.504/SOR-18. 10 sq. mm 4 core |
| 41 | S/F of 6 Amp to 32 Amp. SPMCB (10KA) C curve complete in all respect as per direction of Engineer-in-charge. SI No. 1002/18. CAT-A. |
| 42 | ( Incoming 200 Amp. TPN-1 No Outgoing 100 Amp. TNP-2 Nos. Cat. B. Cubicle Type PWD SI No : 802 (a) Supply and erection of factory fabricated and wired metal clad dust and vermin proof floor mounting panel TPN switch board complete with the following HRC type heavy duty TPN fuse switches with fuses and instrument chamber etc. complete in all respects. The instrument chamber shall be separate and shall comprise of flush type ammeter, voltmerer, selector switches for ammeter and voltmeter, instrument fuses, current transormer etc. The board shall have suitable capacity electroytic alumininum busbars as per IS8623 istulate with heat shrink sleeving and mountend on non hygroscopic supports such as CMC/DMC support with deteachable side covers and shall be suitable for extension on the sides. The switches shall be complete with suitable cable end boxes, reverse entery boxes in case of pedestaal type, cable sockets, compression glands and indicating lamp on incoming etc. The job includes the grounting of the board as per direction of Engineer-in-Charge. All coutgoing switches of 100 Amp. and above will be provided with ampere metre current transformers and selector switches and instrument fuses etc. The switches board shall be fabricated with CRCA sheet with a minimum thickness of 1.6 mm/2 mm. Cubicle type switch board shall be of cat A B & B-II and pedestal type for Cat-B and C only. ( Incoming 200 Amp. TPN-1 No Outgoing 100 Amp. TNP-2 Nos. Cat. B. Cubicle Type PWD SI No : 802 (a) |
| 43 | Supply and burring of Safe Earthing Electrode T-19 (Hot Dip Galvanized), Length up to 2000mm, outer pipe 50mm, inner pipe 25, terminal Dia 12 mm, outer GI pipe of 16 swg and inner GI pipe of 12 swg with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30cm square C.I. frame with hinged cover & masonry husing (from electrode terminal to switch board, cost of 25 x 3 G.I . strip will be extra) Make: As approved in U.P. P.W.D., & C.P.R.I. Certified. PWD SI No :725 (A) |
| 44 | Mild steel or iron work in plain work such as in R.C.C. or R.B. (when not included in an over all rates ) including bending for proper completion of the work and including supply of steel and its wastage , bends, hooks and authorised overlaps shall be measured up to floor two level- L.D.A APPRO. |
| 45 | Wiring Points in Conduit Partly Laid in slab and partly Concealed in Wall, Wiring point for light with 1.5 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid steel conduit pipe partly concealed in the wall and partly laid in slab alongwith the reinforcement before concreting, complete with 14 SWG copper earth continuity wire,GP Box, piano type switch & ceiling rose/angle/batten holder on 3mm thick phenolic paminated backalite sheet etc complete in all respect as directed including matching colour wash. SOR 2018 (E-M)- 1.3.138 (B) |
| 46 | Wiring Points in Conduit Partly Laid in slab and partly Concealed in Wall, Wiring point for fan / fresh air fan (light duty exhaust fan) with 1.5 sq.mm.FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid steel conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting, complete with 14 SWG copper earth continuity wire,GP Box , piano type switch & ceiling rose on 3 mm. thick backelite sheet etc., complete in all respect including matching colour wash. SOR 2018 (E-M)- 1.3.140 (B) |
| 47 | Wiring Points in Conduit Partly Laid in slab and partly Concealed in Wall, Wiring point for plug with 1.5 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid steel conduit partly concealed in wall and partly laid in slab alongwith the reinforcement before concreting, complete with14 SWG copper earth continuity wire and piano type switch and socket etc., complete in all respect including matching colour wash. SOR 2018 (E-M)- 1.3.141 (B) |
| 48 | Miscellaneous items, Addition when modular type switches etc. are used in place of piano type switches etc. in various wiring points. Add for light / fan points with modular type switch in place of piano type switch. SOR 2018 (E-M)- 1.5.187 (A) |
| 49 | Miscellaneous items, Addition when modular type switches etc. are used in place of piano type switches etc. in various wiring points. Add for plug point with modular switch & socket in place of piano type switch & socket. SOR 2018 (E-M)- 1.5.187 (C) |
| 50 | Supply and fixing of power plug with 20 Amp./250 volt flush type modular switch and 5 pin 20 A/250 volt flush type universal modular socket switch on concealed M.S box including supply of all material, labour T&P etc. required for proper completion of SOR 2018 (E-M)- 11.1139 (A) |
| 51 | Submain in conduit (partly laid in slab and partly concealed in wall ( 2 Wire 1100 V Grade), Supply and wiring of submain with two number 4 sq.mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm dia heavy guage rigid steel conduit partly concealed in wall and partly laid in slab alongwith reinforcement before concreting, with one number 14 SWG copper earth continuity wire including matching colour wash etc. complete in all respect. SOR 2018 (E-M)- 2.3.221(B) |
| 52 | Submain in conduit (partly laid in slab and partly concealed in wall ( 2 Wire 1100 V Grade), Supply and wiring of submain with two number 10sq.mm.FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 25 mm dia heavy guage rigid steel conduit partly concealed in wall & partly laid in slab along with reinforcement before concreting, with one number 10 SWG copper earth continuity wire including matching colour wash etc. complete in all respect. SOR 2018 (E-M)- 2.3.223(B) |
| 53 | S & F surface/Flush mounting 12 ways SPN distribution board with additional metal door without MCB complete in all respect, as Direct by Engineer in Charge., CAT B SOR 2018 (E-M)- 10.1025 (A).b |
| 54 | S&F of 6 Amp to 32 Amp. SPMCB (10 KA) C Curve, CAT A SOR 2018 (E-M)- 10.1002.a |
| 55 | S&F of 40 Amp. DP MCB (10 KA) C Curve, CAT A SOR 2018 (E-M)- 10.1010.a |
| 56 | S & F sheet steel enclosure for T.P./Four Pole MCB., CAT B SOR 2018 (E-M)- 10.1033.b |
| 57 | Supply and burying of 600mm x 600mm x 6mm G.I. plate vertically for earthing with its top at least 3 metres below ground level complete with 20mm dia G.I. pipe and funnel for watering and one earthing lead of two no. 8 to 10 SWG GI wire in 15mm dia G.I. pipe up to switch board (from appron to switch board the cost of G.I. pipe and G.I. wire will be extra) 30cm square C.I. frame with hinged cover masonry housing alternate layers of charcoal/coke and salt at least 150mm thick alround etc. as per directions of Engineer-in-charge complete in all respect. SOR 2018 (E-M)- 7.703 |
| 58 | Supply and fixing of one number 8 SWG G.I. wire in 15mm dia. G.I. pipe for earthing, laid in ground or in wall duly concealed including the cost of cement, sand, labour, T&P other material required for proper completion of the work as directed at site. SOR 2018 (E-M)- 7.721 |
| 59 | Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge, complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc., 10 sq. mm 2 core SOR 2018 (E-M)- 5.501.(b) |
| 60 | Supply and fixing of plain or pin type copper tin plated cable socket ( lug ) to the cable leads, insulating with tape and making connection etc. complete in all respect as per direction of the Engineer-Incharge., 10 sq. mm SOR 2018 (E-M)- 5.504.(c) |
| 61 | Supply and fixing of brass nickle plated compression gland for PVC insulated & armoured served sheathed, underground cable including rubber ring etc. complete in all respect. The armouring of the cable shall be properly connected with the earth as per direction of Engineer-Incharge., 10 sq. mm 2 core SOR 2018 (E-M)- 5.503.(b) |
| 62 | DOWN LIGHT LUMINAIRES Supply and fixing of recess/ Surface/ Pendent mounting round 10 to 15 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/ Reflector and driver set complete in all respect., CAT- AAA SOR 2018 (E-M)- 14.1402.a |
| 63 | DOWN LIGHT LUMINAIRES Supply and fixing of LED Tube Light with batten suitable for up to 1 X 22 watt LED tube light fitting including tube on Surface complete in all respect., CAT- AAA SOR 2018 (E-M)- 14.1413.a |
| 64 | DOWN LIGHT LUMINAIRES Supply and fixing of recess/surface mounting round 24 Watt to 32 Watt LED Down Lighter having Powder coated die cast aluminium housing with extended heat sink, diffuser/ Reflector and driver set completed in all respects., CAT- AAA SOR 2018 (E-M)- 14.1404.a |
| 65 | S/B of Earth rod 20 mm dia 2.5 mt long including GI wire 7/16 SWG to connected earth rod and earth clamp on pole, 3 mtr long steel conduit to carry earth wire along the jpole complite as per approved of E/Ic. - 17(14) |
| 66 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications :, Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand or manufacture DSR 2023- 13.48.3 |
| 67 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:, New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) DSR 2023- 13.47.1 |
| 68 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour., Distempering (Two coat) with oil bound distemper of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as Berger, J&N, Shalimar, Asian paints after thoroughly brushing the surface free from mortar droppings & other foreign matters & also including preparing the surface even with plaster of paris or approved synthetic material & sand papered smooth including cost ofall materials. (For Internal wall surface) DSR 2023- 13.82.2 |
| 69 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). DSR 2023- 16.69 |
| 70 | Construction of granular sub-base by providing coarse graded material, spreading in uniform layer with motor graded on perpared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratoy roller to achieve the desired density complete as per clause 401. for grading I material (GSB-1) (Sanction rate) -1001 |
| 71 | Supply, Installation, laying & Commissioning of 90 mm outer dia 6 kg/cm2 HDPE pipe. 33.01 (jal nigam varansi SOR ) PSR |
| 72 | Supply, Installation, laying & Commissioning of HDPE Flange with tail piece, packing & nut bolt complete in all respect. - PSR-07 |
| 73 | Supply, Installation, laying & Commissioning of ELBOW Joint 90 Degree for 90 mm HDPE pipe- PSR-09 |
| 74 | Supply, Installation, laying & Commissioning of 90 mm TAIL Pieces HDPE Pipe. - PSR-14 |
| 75 | Supply, Installation, laying & Commissioning of 63 mm TAIL PIECES . - PSR-13 |
| 76 | Supply, Installation, laying & Commissioning of TEE Joint 90 Degree for 63 mm HDPE pipe- PSR-12 |
| 77 | Supply, Installation, laying & Commissioning Pressure Gauge 2.5” size (Gyceryne) - PSR-15 |
| 78 | 3” Disc Filter- PSR-16 |
| 79 | Supply, Installation, laying & Commissioning of ELBOW Joint 90 Degree for 63 mm HDPE pipe- PSR-10 |
| 80 | 2” Disc Filter- PSR-17 |
| 81 | \\"Supply, Installation, laying & commissioning of 63 mm outer dia 6Kg/cm2 HDPE pipe. 33.01 (Jal Nigam Varanasi SOR)\\" - 33.01 a ( Jal Nigam Varanasi SOR ) |
| 82 | Supply, Installation, laying & Commissioning of reducer 90 mm to 63 mm outer dia 6 kg/cm2 HDPE pipe- PSR-08 |
| 83 | Thermos Temperature Controllers with switch and socket 2 mm cable- PSR-19 |
| 84 | Butt Belding electric heating plate- PSR-20 |
| 85 | 3\\" CI Butterfly valve. -1995 |
| 86 | 2” CI butterfly Valve- PSR-22 |
| 87 | Supply, Installation, laying & Commissioning of service saddle 2 inch x 1.25 inch. - PSR-24 |
| 88 | Supply, Installation, laying & Commissioning of service saddle 3 inch x 1.25 inch. (Sprinkler) - PSR-23 |
| 89 | Supply, Installation, laying & Commissioning of swing joint for 10-12 meter range 360 degree popup- PSR-25 |
| 90 | Supply, Installation, laying & Commissioning of pip sprinkler plastic make material with 10-12 meter range 360 degree- PSR-30 |
| 91 | Supply, Installation, laying & Commissioning of 25 mm outer dia 6kg/cm2 CPVC pipe- PSR-26 |
| 92 | Supply, Installation, laying & Commissioning of Ball valve for 25 mm pipe- PSR-27 |
| 93 | Supply, Installation, laying & Commissioning of pip sprinkler plastic make material with 3 4 meter range 360 degree- PSR-29 |
| 94 | Engagement of Plumber for required work etc all complete as per direction of Engineer in charge. PWD SOR 2020-21/Labour Rates Chapter. Rs. 420.00+10%CP- Approved Rate Rs. 462.00 |
| 95 | Engagement of Labour for required work etc all complete as per direction of Engineer in charge. PWD SOR 2020-21/Labour Rates Chapter. Rs. 335.00+10%CP- Approved Rate Rs. 368.50 |
| 96 | 'Plumber/Electrician (licenced with kit) grade 1/PWD SOR- PWD SOR 4394.243 |
| 97 | Supply and fixing of pump set & composite electric panel for submersible kirloskar/ sons/ crompton openwell pumpset greeves make three phases 380-440 v 50 cycles supply with fountain bolts and 3 core 2.5 mm flat PVC flexible copper conductor double insulated submersible cable and 4 core 1.5 mm form fountain pool to fountain electric panel etc fountain pool to fountain electric panel etc. complete with internal wiring lighting system. 7.5 HP pump 41260.00- 7.5 HP pump 69 A 41260.00 |
| 98 | Supply and fixing of pump set & composite electric panel for submersible kirloskar/ sons/ crompton openwell pumpset greeves make three phases 380-440 v 50 cycles supply with fountain bolts and 3 core 2.5 mm flat PVC flexible copper conductor double insulated submersible cable and 4 core 1.5 mm form fountain pool to fountain electric panel etc fountain pool to fountain electric panel etc. complete with internal wiring lighting system.Electric Panel Box- PSR . |
| 99 | Supply and fixing of 3 HP single phase open well submersible pump set of 50 mm x 50 mm pipe size complete with all material, labour T&P etc all as per direction of Engineer in charge. (make kirloskar/ crompton/KSB 26504.00- S/F 26504.00 |
| 100 | Supplying and stacking of well decayed cattle manure at site including royalty and carriage upto 5 k.m.lead complete (Cattle manure measured in stacks will reduced by 8% for Payment). DSR - 2020 (Horticulture)- 2.25 |
| 101 | Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge DSR - 2020 (Horticulture)- 2.9 |
| 102 | Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately). DSR - 2020 (Horticulture)- 2.8 |
| 103 | Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure). DSR - 2020 (Horticulture)- 2.1 |
| 104 | Fine dressing of the ground. DSR - 2020 (Horticulture)- 2.7 |
| 105 | Preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge. DSR - 2020 (Horticulture)- 2.28 |
| 106 | Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately), \\"Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately)Holes 60 cm dia, and 60 cm deep./DSR Horticulture 2020; 2.14.4\\" DSR - 2020 (Horticulture)- 2.14.4 extra |
| 107 | Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water), Trees Plant DSR - 2020 (Horticulture)- 2.57.1 |
| 108 | Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water), Shrubs Plant DSR - 2020 (Horticulture)- 2.57.2 |
| 109 | Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water), Hedge Plant /Ground cover DSR - 2020 (Horticulture)- 2.57.3 |
| 110 | Providing and stacking of Murraya exotica of height 45-60 cm. in poly bags of size 15 cm as per direction of the officer-in-charge. DSR - 2020 (Horticulture)- 8.46 |
| 111 | Providing and Displaying Acalypha red well developed with fresh & healthy 30 to 45 cm ht. in 20 cm size Earthen Pot/ Plastic Pot as per direction of the officer-in-charge. DSR - 2020 (Horticulture)- 5.3 |
| 112 | Providing and displaying of Syngonium golden mounted on moss stick 90 cm ht., 3 to 4 s placed in each pot at equal distance, well developed with full of fresh & healthy leaves from bottom to top in 25 cm size of Earthen pot/Plastic pot & as per direction DSR - 2020 (Horticulture)- 3.91 |
| 113 | Providing and displaying of Syngonium Variegated mounted on moss stick 90 cm ht., 3 to 4 s placed in each pot at equal distance, well developed with full of fresh & healthy leaves from bottom to top in 25 cm size of Earthen pot/Plastic pot & as per direct DSR - 2020 (Horticulture)- 3.92 |
| 114 | Providing and stacking of Ophiopogon jaburan (variegated ), full of variegated leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. DSR - 2020 (Horticulture)- 6.20 |
| 115 | Providing and stacking of Chandni dwarf of height 15-20 cm., well branched in earthen pots of size 20 cm as per direction of the officer-in-charge. s per direction of the officer-in-charge. DSR - 2020 (Horticulture)- 8.14 |
| 116 | Providing and stacking of Bauhinia acuminata height 60-75 cm. in earthen pots of size 20 cm as per direction of the officer-in-charge. DSR - 2020 (Horticulture)- 8.1 |
| 117 | Providing and stacking of Bauhinia tomentosa (yellow) of height 60-75 cm. in earthen pots of size 20 cm as per direction of the officer-in-charge. DSR - 2020 (Horticulture)- 8.2 |
| 118 | Providing and stacking of Caesalpinia pulcherrima species of height 45-60 cm. in earthen pot of size 20 cm as per direction of the officer-in-charge. DSR - 2020 (Horticulture)- 8.4 |
| 119 | Providing and stacking of Calliandra hybrida of height 105-120 cm., well branched, bushy in big size HDPE bag as per direction of the officer-in-charge. DSR - 2020 (Horticulture)- 8.7 |
| 120 | Providing and stacking of Allamanda cathartica of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge. DSR - 2020 (Horticulture)- 9.1 |
| 121 | Providing and stacking of Bignonia venusta (Golden shower) of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge. DSR - 2020 (Horticulture)- 9.3 |
| 122 | Providing and stacking of Ipomoea purpurea (Morning glory) of height30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge. DSR - 2020 (Horticulture)- 9.7 |
| 123 | Providing & laying Selection no. 1 doob grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with required tools wooden and than rolling the surface with light roller make the surface smoothen and light watering the same maintenance for 30 days or more till the grass establish properly,as per direction of officer in charge DSR - 2020 (Horticulture)- 2.34 |
| 124 | Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, herbs, edge, flower beds, foliages, creepers etc. including hoeing,weeding, pruning, replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter, removal of garden waste, applying insecticide, pesticide & fertilizers (whenever required) top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide, Pesticide will be provided by the Department & lawn mover and brush cutter with fuel and other T & P material/articles shall be provided by the contractor.) and as per direction of officer in charge., Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, herbs, edge, flower beds, foliages, creepers etc. including hoeing,weeding, pruning, replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter, removal of garden waste, applying insecticide, pesticide & fertilizers (whenever required) top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide, Pesticide will be provided by the Department & lawn mover and brush cutter with fuel and other T & P material/articles shall be provided by the contractor.) Play grounds / Public parks (1Mali for 2.00Acre). DSR - 2020 (Horticulture)- 2.40.5 |
| 125 | Cutting of Hedge/Edge including removing of cut material, cleaning, hoeing of hedge/edge bed watering, manureing and applying insecticides and fungicides etc.(excluding the cost of material which shall be supplied by the department) and as per direction of officer in charge. DSR - 2020 (Horticulture)- 2.36 |
| 126 | Supply & stacking Urea 40% Nitrogen @ 160 kg per acre (as per yard stick of CPWD LDA SOR 2018-19/11.1 OLD DSR- SOR 2018-19 11.1 |
| 127 | Supply & stacking DAP 50 kg per acre/year. LDA SOR 2018-19/11.2 OLD DSR- 11.2 |
| 128 | Supply & Stacking Bone Meal/ Oil Cake (LDA SOR Horti 2018-19/11.3) 50 kg per acre/Year |
| 129 | Removal of garden waste by TATA 407 or equivalent including loading/ unloading and carriage upto 1 km lead,complete disposal upto designated place as per direction of officer-in-charge . DSR - 2020 (Horticulture)- 2.60 |
| 130 | Providing and Displaying Acalypha twisted well developed with fresh & healthy 30 cm ht. in 20 cm size Earthen Pot/ Plastic Pot as per direction of the officer-in-charge. DSR - 2020 (Horticulture)- 5.40 |
| 131 | Rough dressing the trenched ground including breaking clods. DSR Horticulture 2020; 2.6- DSR Horticulture 2020; 1.55 |
| 132 | Providing and Displaying of Spathiphyllum (peace lily), having 15 cm to 25 cm ht. blooming stag with fresh & healthy foliage well developed in 15 cm of Earthen pot/plastic pot as per direction of officer-in-charge- DSR 2020 Horti 3.90 |
| 133 | Providing and Displaying Topiary of Ficus Panda well developed with fresh & healthy foliage with 3 to 4 Ball and 60 to 75 cm spread each Ball, 135 to 150 cm ht., in 35 cm Cement Tray /Cement Pot as per direction of the officer-in-charge. - DSR 2020 Horti 5.40 |
| 134 | Provding and stacking of jacaranda mimosifolia of height 10-12 feet in big poly bogs of size 18 as per direction of the office-in-charge sanctioned rate. -580 |
| 135 | Providing and stacking of tabeblua healthy and multi branches of ht. 10-12 feet in Earthen pots of size 12\\" as per direction of the officer-in-charge. Sacntioned Rate- Tabeblua12inch |
| 136 | Providing and stacking of Terminalia Mentali healthy and multi branches of height 10-12. in big polybags of size 18\\" as per direction of the officer-in-charge. /Market Rate- 1500.Terminalia Mentali |
| 137 | Providing and stacking of tabebiua healthy and multibranches of ht.10-12 feet in Earthen pots of size 12'' as per direction of the officer-in-charge. - Sanctioned Rate.13 |
| 138 | Providing and stacking of Plumeria alba healthy and multi branches of height 10-12 feet in big poly bags of size 18\\" as per direction of the officer-in-charge. - PSR SAUMITRA CE516 |
| 139 | Providing and stacking of Madagaskar Almond ( Terminalia Mantally) of height 360 cm to 420 cm big foilage well developed multiple branches in 63 cm big poly bags ofsize as per direction of the officer-in-charge. -514 |
| 140 | Providing and stacking of Mimusops elengi (Maulsri) of healthy and multi branches of height 10-12 ft in big poly bag of size 18\\" as per direction of the officer-in-charge. - Mimusops elengi (Maulsri) 01 |
| 141 | Providing and stacking of Butea frondosa (Flame of Forest) healthy and multi branches of height 4-6 feet in big poly bags of size 18\\" as per direction of the officer-in-charge. - PSR SAUMITRA CE498 |
| 142 | Providing and stacking of Erythrina indica healthy & multi branches of height 12-14 feet in big poly bags of size 18\\" as per direction of the officer-in-charge. - Erythrina indica |
| 143 | Providing and stacking of Lagerstroemia flaush (Jarool) healthy & multi branches of height 10-12 feet in big poly bags of size 12\\" as per direction of the officer-in-charge. - sanction/Lagerstroemia flaush |
| 144 | Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: Butt hinges and necessary screws shall be paid separately), Second class teak wood, 35 mm thick shutters DSR 2023- 9.5.1.1 |
| 145 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately)., Second class teak wood DSR 2023- 9.1.1 |
| 146 | Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows all complete with :, 5.5 mm thick glass panes. DSR 2023- 10.30.2 |
| 147 | Providing and fixing ISI marked IS:1341 M.S. pressed butt hinges bright finished with necessary screws etc. complete :, 125x65x2.12 mm DSR 2023- 9.55.1 |
| 148 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete (Copper oxidised as per IS 1378), 200x10 mm DSR 2023- 9.63.2 |
| 149 | Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete (Copper oxidised as per IS 1378), 100 mm DSR 2023- 9.66.2 |
| 150 | 'Providing & fixing sand stone Single piece ornamental bench of approved design pattern (1200x450x450MM) and specifications including , all materials, labour and T & P etc. required for proper completion of work as directed by engineer - in -charge PSR- PSR 4394.76 |
| 151 | 'Providing & fixing of Dustbin made in mild steel frame with painting & polish and frame wooden member fixed in m.s. frame including painting polishing as per drawing & design all complete in direction of engineer in charge. PSR- PSR 4394.77 |
| 152 | Supplying and Fixing of Four Seater Swing with sparrow outdoor playing equipment including necessary fittings, T&P etc all complete in direction of engineer in charge. (Model No. FPSW 10, Make Fun Play/ Kompain/ Arihant) - Sanctioned Rate 55810 |
| 153 | Supplying and Fixing of Standered Multi seater See Saw outdoor playing equipment including necessary fittings, T&P etc all complete in direction of engineer in charge. (Model No. FPSS12, Make Fun Play/ Kompain/ Arihant) - Sanctioned RAte 17578 |
| 154 | Supplying and Fixing of Turbo Tower outdoor playing equipment including necessary fittings, T&P etc all complete in direction of engineer in charge. (Model No. FPCL35 , Make Fun Play/ Kompain/ Arihant) - Sancitoned Rate 43945 |
| 155 | Supplying and Fixing of Monkey Climber Outdoor Playing Equipment Including Necessary Fittings, T&P ete all Complete in Direction of Engineer in Charge. (Model No. FPCL43, Make Fun Play/Kompain/ Arihant) Rate 49438.00- Rate 49438.00 |
| 156 | Supplying and Fixing of Balancing Bridge outdoor playing equipment including necessary fittings, T&P etc all complete in direction of engineer in charge. (Model No. FPTH41, Make Fun Play/ Kompain/ Arihant) - Sanctioned Rate 64270 |
| 157 | Supplying and Fixing of Four Seater Merry Go Round Outdoor Playing Equipment Including Necessary Fittings, T&P etc all Complete in Direction of Engineer in Charge. (Model No. FPMR11, Make Fun Play/ Kompain/ Arihant) Rate 50756.00- Rate 50756.00 |
| 158 | Supplying and Fixing of 7' Ht. FRP Wave Slide Outdoor Playing Equipment Including Necessary Fittings, T&P etc all Complete in Direction of Engineer in Charge. (Model No. FPSD51, Make Fun Play/Kompain/ Arihant) Rate 71960.00 |
| 159 | Supplying and Fixing of Frog Bin - FRP outdoor playing equipment including necessary fittings, T&P etc all complete in direction of engineer in charge. (Model No. FPDB11, Make Fun Play/ Kompain/ Arihant) - Sanctioned Rate 14831 |
| 160 | Supplying and Fixing of Imperial Bench 4' outdoor playing equipment including necessary fittings, T&P etc all complete in direction of engineer in charge. (Model No. FPGD11, Make Fun Play/ Kompain/ Arihant) - Sanctioned Rate 19995 |
| 161 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels., Granite stone slab colour black, Cherry/Ruby red, Area of slab over 0.50 sqm DSR 2023- 8.2.2.2 |
| 162 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge :, With average thickness of 120 mm and minimum thickness at khurra as 65 mm. DSR 2023- 22.7.1 Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
