|
| 1 | Demolition of cement concrete in ground floors and pavings n exc 15cm thick (below or above ground level), complete all as specified and directed. |
| 2 | M&L for 75mm thick plain cement concrete, 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base, complete all as specified and directed. |
| 3 | M&L for 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and direction. |
| 4 | S&F chequered cement concrete tiles size 300 mm x 300 mm x 22-25mm thick with grey cement and pigment , rubber moulded glossy finish, ISI marked, coloured, set jointed and pointed in neat cement slurry over and including 15 mm thick screed bed in CM 1:6, complete all as specified and directed. |
| 5 | S&F GI frame work of size 605 x 605mm for seamless ceiling comprising of Gl perimeter channel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 45 mm centre to centre/intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2m length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre including supply and fixing 8mm thick Gypsum Board (water proof) fixed with screw or as per manufacturers instructions and jointing and finishing to a flush finish of tapered and square edges other board any other joints with recommended jointing compound over jointing tapes, finishing with one coat of primer and two coats of oil emulsion distemper over a coat 2mm thick wall care putty including dismantling of existing ceiling, complete all as specified and directed. |
| 6 | S&F in repairs 6mm thick non asbestos fibre cement building boards fixed or laid/inserted to timber /GI / aluminium framework with screws to ceiling flat or sloping, complete all as specified and directed. |
| 7 | Preparation of new or previously untreated plaster/ AC sheet / Gypsum board surfaces of ceiling including cornices and applying two coats of oil bound distemper colour / tint, complete all as specified and directed. |
| 8 | S&F in repairs 12mm thick wooden wall panelling of second class softwood with tongue and groove joint fixed in any position over and including wooden framework in second class softwood with plain fillets square or sectional area exc 13 Sqcm and n exc 25 Sqcm at n exc 90 cm centre to centre in both direction and including two or more coats of French polishing on all the exposed surfaces wooden panelling including taking down existing electrical fittings and re-fixing the same, complete all as specified and directed. |
| 9 | Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed. |
| 10 | M&L for structural steel work as in truss, rafter purling, made out of angle / Hollow pipe / tube section including jointing cleats, plates flat iron, gusset plates, rails, braces etc. conforming to Fe 410-W (gde-E-250) Quality, confirming to IS-1161-1979 of grade St-240 complete all as specified and as directed. |
| 11 | S&F in repairs 0.63 mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, with L-type or J-type or cranked hook bolts, in roofs, walls etc. with grade of zinc coating, complete all as specified and directed. |
| 12 | All as per Ser item No 11.00 here in before but except Sheets. |
| 13 | S&F in repairs 0.63mm thick Galvanised, Plain mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating, complete all as specified and directed. |
| 14 | Preparing new zinc (or galvanised) surfaces to receive painting of any description over 10cm width or girth, by coating with mordant solution including washing and cleaning, etc. steel and iron surfaces and applying two coats of synthetic enamel paint in camouflaging CCD pattern as approved, complete all as specified and directed. |
| 15 | Dismantling of floor hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed. |
| 16 | M&L for 40 mm thick plain cement concrete, 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) as in sub base, complete all as specified and directed. |
| 17 | M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. Set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in CM 1:6, complete all as specified and directed. |
| 18 | M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. Set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in CM 1:6, complete all as specified and directed. |
| 19 | M&L for Glazed ceramic tile 450x 300 x 06-7mm thick (coloured) on vertical surfaces such as wall, dados etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 10 mm thick screed bed in CM 1:4, complete all as specified and directed. |
| 20 | M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. Set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in CM 1:6, complete all as specified and directed. |
| 21 | M&L for Non skid joint free Ceramic tiles 7 to 8 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 Sqm, as on vertical surfaces, such as skirting/dado set and jointed in neat cement slurry and pointed in coloured cement to match colour of tiles over and including 10mm thick screed bed in CM 1:4, complete all as specified and directed. |
| 22 | M&L for 08 to 10 mm thick vitrified parking tiles in approved shade from meteor series, area of each tile exceeding 0.08 Sqm but not exceeding 0.18 Sqm in floors etc., set and jointed in neat cement slurry and pointed in matching coloured polymer cement based grout to match over and including 15 mm thick Screed bed or bedding layer in CM 1:6, complete all as specified and directed. |
| 23 | M&L for 18-20 mm thick Machine cut Kota stone slab flooring over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 20 mm thick screed bed in CM 1:6, complete all as specified and directed. |
| 24 | M&L for 18-20 mm thick Machine cut Kota stone slab flooring over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing in skirting / dado complete over and including 10 mm thick screed bed in CM 1:4, complete all as specified and directed. |
| 25 | M&L for grinding and polishing of existing of Kota stone / tarrazo tiles flooring polished upto mirror finish complete all as specified and directed |
| 26 | Taking down Chowkhats or frames with shutters (without taking off shutters from the frames) n exc. 1.5 Sqm and credited to the contractor, complete all as specified and directedNote: The damaged portion of the tiles / rendering shall be made good with the same material to match with the adjacent surface. |
| 27 | Taking down Chowkhats or frames with shutters (without taking off shutters from the frames) exc. 1.5 Sqm but n exc 4.0 Sqm and credited to the contractor, complete all as specified and directedNote: The damaged portion of the tiles / rendering shall be made good with the same material to match with the adjacent surface. |
| 28 | Taking down shutters of any description size of shutter exc 1 Sqm but n.exc 2 Sqm and removing from site complete all as specified and directed. |
| 29 | S&F pressed steel frame for doors with one rebates size of frame 125x60 mm including necessary fixing lungs hinges lock strike plate etc. including PCC, 1:3:6, type C-0 (using 12.5 mm graded crushed stone aggregate) as in back filling of pressed steel frame, complete all as specified and directed. |
| 30 | S&F pressed steel frame for doors with one rebates size of frame 105x60 mm including necessary fixing lungs hinges lock strike plate etc. including PCC, 1:3:6, type C-0 (using 12.5 mm graded crushed stone aggregate) as in back filling of pressed steel frame, complete all as specified and directed. |
| 31 | Preparation of new steel surface and iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over red oxide primer, complete all as specified and directed. |
| 32 | S&F 30mm thick 2nd class hardwood, factory made, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a), complete all as specified and directed. |
| 33 | S&F 30mm thick 2nd class softwood plain framed panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board with commercial face veneers, complete all as specified and directed. |
| 34 | S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed. |
| 35 | Preparation of new wood and wood based surfaces of any description exc 10cm with or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed. |
| 36 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying and fixing in opening, complete all as specified and directed. |
| 37 | S&F 30mm thick Factory made Solid Panel PVC Door Shutter (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing, complete all as specified and directed. |
| 38 | S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete all as specified and directed. |
| 39 | S&F 150mm size Aluminium handles, cast type, anodised, complete all as specified and directed. |
| 40 | S&F 150mm size Aluminium anodised, barrel tower bolts of extruded section, complete all as specified and directed. |
| 41 | S&F 125mm size Aluminium handles, cast type, anodised, complete all as specified and directed. |
| 42 | S&F 125mm size Aluminium anodised, barrel tower bolts of extruded section, complete all as specified and directed. |
| 43 | S&F in repairs 100mm long medium weight, cold rolled mild steel Butt hinges, complete all as specified and directed.. |
| 44 | S&F 140mm floor door stopper of aluminium body and tongue anodised with land drawn steel spring overall length of cover plate, fixed with screws, complete all as specified and directed. |
| 45 | S&F aluminium powder coated aluminium window having three track (minimum thickness of powder coating 50 micron) with aluminium section 92mm X 31.75mm (Weight bottom section 1.070 kg/m, top section 0.933 kg/m, shutter section 40mm X 18mm (weight of handle section 0.417 kg/m) interlock 0.547 kg/rm mounted on bearing to slide on tracks plain anodized in approved shade including supply and fixing of 5mm thick plain glass and wire mesh, PVC track gasket, EPDM rubber gasket on glass of weather tightening along with locks, handle including sealing gap with marble surfaces with silicon sealants making it water proof in all manner etc. complete all as specified and directed. |
| 46 | S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed. |
| 47 | S&F aluminium powder coated glazed shutter (for doors) with frame of section size 101.60x44.45mm 16 gauge and style and top rail of section 80 x 44mm, 16 Gauge thick and bottom rails of section 112 x 44mm of 16 Gauge thick, middle rail 150 x 44mm of 16 guage thick fixed on floor spring, both side opeining without sash bars but including 5mm thick plain/tinted / heat reflecting glass pan with and necessary jointing cleats, rubber beading, anodized aluminium snap beading, screws, aluminium anodized handle, locking arrangement (mortice lock) and aluminuium anodised tower bolt 200 mm long and hydraulic floor door spring, complete all as specified and directed. |
| 48 | Demolition of reinforced cement concrete of any description in any position not otherwise specifically provided for, complete all as specified and directed. |
| 49 | Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work for fair finished surface, not exceeding 200m thick (Horizontal or sloping), complete all as specified and directed. |
| 50 | M&L for Reinforced cement concrete, 1:2:4, Type B-1 (using 20 mm graded crushed stone aggregate) for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed. |
| 51 | M&L for MS TMT bars 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooking for columns, hooking ends and binding with and including mils steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed. |
| 52 | S&F in repairs 20mm dia stainless steel drapery curtain rods including brackets, end finials (Latoo), for curtain rails fancy decorative type and fix with brass screws to walls approved quality etc., complete all as specified and directed. |
| 53 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc., complete all as specified and directed. |
| 54 | M&L for 18 to 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms with gas pipe hole, wash basin platform and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade, complete all as specified and directed. |
| 55 | S&F in repair 75mm outer dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls with clamp or laid in trenches, complete all as specified and as directed. |
| 56 | S&F in repair 110mm outer dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls with clamp or laid in trenches, complete all as specified and as directed. |
| 57 | S&F 100 / 75mm outlet PVC (SWR) floor trap with chromium plated grating including Jointing to waste pipe and fixed in cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate), complete all as specified and directed. |
| 58 | S&F 75mm size PVC (SWR) bends of any radius, complete all as specified. |
| 59 | S&F 75mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door, complete all as specified and directed. |
| 60 | S&F 110mm size PVC (SWR) bends of any radius, complete all as specified. |
| 61 | S&F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door, complete all as specified and directed. |
| 62 | S&F 110mm bore PVC (SWR) 'P’ trap complete all as specified and directed by Engineer-in-Charge. |
| 63 | S&F 75mm bore PVC (SWR) vent cowl, complete all as specified and directed. |
| 64 | Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed. |
| 65 | M&L for brick work with sub-class `B' bricks (using old size bricks), straight or curved on plan exceeding 6m mean radius built in CM 1:6, Complete all as specified and directed. |
| 66 | M&L for brick work with sub class 'B' bricks (using old size bricks) straight or curved on plan to any radius in half brick thick wall radius, built in CM 1:6, complete all as specified and directed. |
| 67 | S&F in repairs 15mm bore hot and cold water mixer with swan neck for WHB chromium plated quarter turn screwed down, including necessary fittings, complete all as specified and directed. |
| 68 | S&F in repairs 15mm size sink mixer for mixing hot & cold water, cast copper alloy chromium plated with capstan heads, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe, complete all as specified and directed. |
| 69 | S&F in repairs 15 mm size wall mixer for mixing hot & cold water, cast copper alloy chromium plated with capstan heads, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe, complete all as specified and directed. |
| 70 | Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc., complete all as specified and directed. |
| 71 | M&L for 15mm thick rendering on other than fair faces of brick or concrete surfaces in cement mortar 1:6, finished even and smooth without using extra cement, complete all as specified and directed. |
| 72 | M&L for 15mm thick rendering on fair faces on brick or concrete surfaces in CM 1:4, fair finished the surfaces even and smooth without using extra cement including scaffolding upto 12m height, complete all as specified and directed. |
| 73 | Preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of chalk whiting, on plastered surface preparatory to distempering , complete all as specified and directed. |
| 74 | Preparation of new surface of wall and applying two coats of cement based paint over one coat of primer including scaffolding up to 15m height, complete all as specified and directed. |
| 75 | S&F in repairs for 15mm bore tubes, medium grade, galvanised, with all fitting, (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc.) and fixed complete to and ceiling with clips, wall hooks, wooden plugs or laid in floors including screwing and waste and for forged bends on piping as required, complete all as specified and directed. |
| 76 | S&F in repairs for 20mm bore tubes, medium grade, galvanised, with all fitting, (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc.) and fixed complete to and ceiling with clips, wall hooks, wooden plugs or laid in floors including screwing and waste and for forged bends on piping as required, complete all as specified and directed. |
| 77 | M&L for Lagging to 20mm bore pipes used in external water supply or plumbing all around with 50mm thick bonded mineral wool pre-formed ‘SNAP ON’ pipe sections of density 144 Kg /Cum conforming to IS 9842 provided with chicken mesh wire netting 25gauge 20mm mesh including applying with brushing neat cement slurry with 3 kg of cement per Sqm complete, complete all as specified and directed. |
| 78 | S&F in repairs vitreous china wash hand basin, white flat back, size of 550x400mm including cutting for and pinning in ends of brackets (including supply and fixing of brackets) or erecting stand, 32mm brass chromium plated waste fitting with long screwed shank and fly nut flangedend bedded in red led cement, chain and plug and porcelain stopper, complete all as specified and directed. |
| 79 | S&F in repairs 15mm size PVC connections with PTMT nuts of length 600mm, complete all as specified and directed. |
| 80 | S&F in repairs 32/40 mm dia bore PVC flexible pipe for wash hand basin / urinal, complete all as specified and directed. |
| 81 | S&F in repairs looking mirror of size 600x450mm with PVC moulding, complete all as specified and directed. |
| 82 | S&F in repairs Vitreous China wash down water closet one piece pan (Pedestal pattern), white/ coloured including all fittings, fixing bolts, flushing cistern, jet spray and flush pipe, complete all as specified and directed. |
| 83 | S&F in repairs Vitreous china squatting pan, Orissa pattern, size 580 x 440mm and making good, including connection to trap, and to flushing pipe, anti-syphonage pipe, etc., including trap set in and including concrete, complete all as specified and directed. |
| 84 | S&F in repairs 10 litre capacity PVC valveless, Syphonic action type, flushing cistern low level, white with inlet ball valve, float and handle including brackets and PVC flush pipe etc., complete all as specified and directed. |
| 85 | S&F in repairs sink with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm, complete all as specified and directed. |
| 86 | S&F in repairs 15mm bore bib tap, cast copper alloy, chromium plated, fancy type, long body with crutch or butterfly handle, screwed for iron pipe or for brass ferrule, complete all as specified and directed. |
| 87 | S&F in repairs 15mm bore Stop valve / angle valve, cast copper alloy, chromium plated, fancy type, screwed down high pressure with capstan head, complete all as specified and directed. |
| 88 | S&F in repairs brass chromium plated tubular towel rail 20mm dia \\"D\\" type 60cm long between flanges, complete all as specified and directed. |
| 89 | S&F in repairs stainless steel soap dish fixed to wall with plug and screw, complete all as specified and directed. |
| 90 | S&F 500 litres capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including 25mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic bal screwed for iron pipe (minimum weight 210 gms) including dismantling existing water tank and removing from site, complete all as specified and directed. |
| 91 | S&F 1000 litres capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including 25mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic bal screwed for iron pipe (minimum weight 210 gms) including dismantling existing water tank and removing from site, complete all as specified and directed. |
| 92 | Complete removal of existing treatment from wall surfaces and applying two coats of oil bound distemper of approved colour including applying 1mm thick JK Birla wall care putty for making the surface even and smooth and filling the uneven and small holes and making the edges of plaster properly by plaster of paris preparatory to distempering including preparation of surface by washing rubbing down and stopping of distempered surfaces, complete all as specified and directed. |
| 93 | Preparation of old plastered / unplastered old decorated surfaces of ceiling, cornices by brooming down or steel brushing, scraping down smoke. moulds , moss and efflorescence salts, trading oil greasy spots etc. and applying one coat of oil bound distemper (OBD), complete all as specified and directed |
| 94 | Preparation of old plastered surfaces of wall by washing down, brooming down or steel wire brushing etc. and applying one coat cement base paint including scaffolding up to 15m height, complete all as specified and directed. |
| 95 | Deduction to be made from BOQ for Schedule 'A' Part-II (Credit Schedule from dismantling / taking down items) worth Rs 89,295.00 during AOC.(Note :- Tenderers shall not quote for this Schedule) Please Enable Macros to View BoQ information |
