|
| 1 | Schedule 'A' Part-I (B/R Work) |
| 2 | Taking down Chowkhats or frames with shutters (without taking off shutters from the frames) n exc. 1.5 Sqm and credited to the contractor, complete all as specified and directedNote: The damaged portion of the tiles / rendering shall be made good with the same material to match with the adjacent surface. |
| 3 | Taking down Chowkhats or frames with shutters (without taking off shutters from the frames) exc. 1.5 Sqm but n exc 4.0 Sqm and credited to the contractor, complete all as specified and directedNote: The damaged portion of the tiles / rendering shall be made good with the same material to match with the adjacent surface. |
| 4 | Taking down and refixing of shutters in same opening after easing and adjusting of any description exc 1 Sqm and n exc 2 Sqm each including resecuring/changing of builders hardware, complete all as specified and directed. |
| 5 | Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards / slabs / blankets, any thickness, including cover fillets, complete all as specified and directed. |
| 6 | Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed. |
| 7 | Demolition of cement concrete of any description including any treatment there to and in any position provided as in roof padding, roof curb etc complete all as specified and as directed. Note: -(a) Demolition should be done carefully to roof slab. (b) Any damage occurred in the roof surfaces during demolition shall be made good by the contractor without extra cost to the department.(c) Disposal of old debris/retrieved material to outside the premises or as directed by the Engineer-in-Charge. |
| 8 | M&L for plain cement concrete, 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in roof padding laid in slope as per requirement mixed with integral water proofing liquid admixture as per manufacturer's instructions, complete all as specified and directed.Note : (i) Minimum thickness of PCC shall be 50mm.(ii) Integral water proofing liquid admixture shall be measured and paid separately under appropriate item here in after. |
| 9 | M&L for 15mm thick screed bed in CM 1:3 finsished even and smooth without using extra cement on roof surfaces using water proofing compound, complete all as specified and directed. (Note : WPC will be measured and paid separately) |
| 10 | Supply only integral water proofing liquid admixture for concrete and mortar (Make : CONPLAST X421IC of Fosroc /SIKA No 1 of SIKA / equivalent brand of Pidilite), complete all as specified and directed. |
| 11 | M&L for water proofing treatment with APP based standard membrane in roof with the following courses of treatment :-(a) Apply bituminous primer @ 0.40 Kg per Sqm of the surface area including cleaning the surfaces, complete all as specified. (MAKE : WP Shield Primer W of SIKA/Shalikote T-32 of STP / Equivalent brand of Tikidan Danosa).(b) Apply APP plastomeric bitumen based mineral finished water proofing membrane polyester reinforced (4 Kg/Sqm) with 10cm over laps and torch bonded at joints including surface preparation before and after application of treatment as per manufactures instruction complete all as specified and as directed. (Make of APP Membrane: WP Shield 103 PM of SIKA/Super Thermolay 3mm (MT) of STP Limited/Equivalent brand of Tikidan Danosa.) |
| 12 | M&L framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings conforming to Fe-410- W (GdeE-250) quality B (exclusive or steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing, complete all as specified and directed. |
| 13 | Taking down cement or cement lime plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water etc., complete all as specified and directed. |
| 14 | M&L 15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4 and finishing even and smooth without using extra cement, complete all as specified and directed. |
| 15 | M&L 15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:6 and finishing even and smooth without using extra cement, complete all as specified and directed. |
| 16 | M&L for 10mm thick rendering on fair faces of brick work or concrete surfaces of ceiling in CM 1:3 and finishing even and smooth without using extra cement, complete all as specified and directed. |
| 17 | Preparation of new plastered surfaces of wall and applying two coats of distemper oil emulsion over a coat of alkali resistant primer including thin layer (1mm thick) of wall care putty and priming coat, complete all as specified and directed. |
| 18 | Preparation of newly plastered surfaces of ceiling and applying three coats of white wash, complete all as specified and directed. |
| 19 | Preparation of new / old plastered surfaces and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm / litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre / 10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 Sqm., complete all as specified and directed. |
| 20 | Complete removal of existing treatment by mechanical means of old surfaces of walls and applying two coats of oil bound distemper over and including 1mm thick wall care putty over plastered surface to prepare the surfaces even and smooth, complete all as specifed and directed. |
| 21 | S&F Gl frame work snap grid frame of size 605 x 605mm for seamless ceiling made out of angle section 22 x 22mm on perimiter walls and tee section of 22 x 22mm in web made to shape out of GI sheet work, and hangers 6mm dia G.I. ( Upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. Flat 40 x 3mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete and including supply and fixing 8mm thick Gypsum perforated particle board of 600 x 600mm size for insulation and accoustics purposes, as per manufacturers instructions and jointing and finishing to a flush finish of tapered and square edges other board any other joints with recommended jointing compound over jointing tapes, complete all as specified and directed. |
| 22 | S&F Box type steel ventilation double frame (glazed & gauged) made of ERW tube P- section of size 60 mm x 25 mm double rebated outer frame comprise glazed Skelton shutter door frame of ERW tube P-section size 50mm x 20mm with two No's openable leaf consisting of two Nos of sash bar of T-sec 20mm x 3mm welded to frame with one No vertical mullion of ERW of ERW box type T-section size of 60mm x25mm FI 2mm thick welded / screwed to frame for fixing of wire gauge/glass and 10mm Sqr Bar security grill including fixture and fitting like as handle, tower bolt stopper , cleat, pintail hinges, holdfast primer etc., complete all as specified and directed.(Note- sheet glass, wire mess will be measured and paid separately and window will be measured one side only) |
| 23 | S&F 4mm thick sheet glass ordinary quality and glazing with oil putty / wooden beading in squares not exceeding 0.50 Sqm, complete all as specified and directed. |
| 24 | S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed. |
| 25 | S&F aluminium window and ventilator shutters powder coated of any colour (thickness or powder coating not less than 50 micron), side hung type without sash bars/ Sliding windows, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.) hinges type B-21 100mm long (2 No.) suitable handle (1 No.) complete all as specified and directed. |
| 26 | S&F Powder Coated aluminium frame for doors, windows, ventilators (minimum thickness of powder coating 50 micron) with one or more rebates including joining cleat for fixing etc., complete all as specified and directed. |
| 27 | S&F 5mm thick PVC sheet as in doors, decorative and white/colour fixed on aluminium frame work including all necessary fittings and fixtures and necessary taping, complete all as per manufactures instructions, complete all as specified and directed. |
| 28 | S&F 5.5mm thick sheet glass, ordinary quality and glazing with aluminium glazing clips and rubber neosprine gasket in square or rectangular in section n exc 0.5 Sqm in each pane with solar control film 25 micron reflective type (gareware sun control or equivalent), complete all as specified and directed by Engineer-in-Charge. |
| 29 | Demolition of cement concrete (unreinforced) of any description in any position, complete all as specified and directed. |
| 30 | Dismantling of floor hearth or wall tiling including cement mortar bedding but not backing removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed. |
| 31 | M&L for 25mm thick plain cement concrete, 1:2:4, type B-0 (using 12.5 mm graded crushed stone aggregate) as in sub base of floor finish even and rough to receive further floor finishes (tile/kota stone/ marble ), complete all as specified and directed. |
| 32 | M&L for 20-25mm thick machine cut Kota stone slab flooring over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing / grinding and polishing upto mirror finish complete over and including 20mm thick screed bed in CM 1:6 and including demolition of existing stone slab and tiles, complete all as specified and directed. |
| 33 | M&L for 20-25mm thick machine cut kota stone slab as in riser of steps, skirting, dado and pillar jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing & polishing over and including 10mm thick backing coat in CM 1:4 and including demolition of existing stone slab and tiles, complete all as specified and directed. |
| 34 | M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc. Set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in CM 1:4, complete all as specified and directed. |
| 35 | M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, as in skirting etc. Set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick screed bed in CM 1:4, complete all as specified and directed. |
| 36 | M&L for Glazed ceramic tile 450x300x06-7mm thick (coloured) on vertical surfaces such as wall, dados etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including 10mm thick screed bed in CM 1:4, complete all as specified and directed. |
| 37 | M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. Set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in CM 1:4, complete all as specified and directed. |
| 38 | M&L for brick work with sub-class `B' bricks (using old size bricks), straight or curved on plan exceeding 6m mean radius built in CM 1:6, Complete all as specified and directed. |
| 39 | M&L for Collapsible steel gates, top hung, consisting for channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified and directed. |
| 40 | Demolition of reinforced cement concrete of any description in any position not otherwise specifically provided for, complete all as specified and directed. |
| 41 | M&L for Reinforced cement concrete, 1:2:4, Type B-1 (using 20 mm graded crushed stone aggregate) for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed. |
| 42 | M&L for Precast reinforced cement concrete, 1:2:4, type B-1 (using 20 mm graded crushed stone aggregates) as in cover slab for soakage well / manhole and similar works supported on walls including necessary formwork and set in cement mortar 1:4, complete all as specified and directed. |
| 43 | M&L for MS TMT bars 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooking for columns, hooking ends and binding with and including mils steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed. |
| 44 | Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work for fair finished surface, not exceeding 200mm thick (Horizontal or sloping), complete all as specified and directed. |
| 45 | M&L for plain cement concrete, 1:2:4, type B-0 (using 12.5mm graded crushed stone aggregates), as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed. |
| 46 | M&L for 75mm thick plain cement concrete, 1:3:6, type C-2 (using 40mm graded crushed stone aggregate) as in pavement / plinth protection, plinth protection shall be laid in alternate bays and joints shall be filled with bitumastic gola with 80/25 bitumen (1 part bitumen mixed with 3 part of sand) finishing surface even and smooth without extra cement, complete all as specified and as directed. |
| 47 | M&L for mild steel framed work for MS Flat around drain cover with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; nosing, framework of water tanks, band, straps, wind ties and similar work conforming to Fe.290.Gde-E-165, complete all as specified and directed. |
| 48 | Preparation of new steel surface and iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over red oxide primer, complete all as specified and directed. |
| 49 | Preparation of new wood and wood based surfaces of any description exc 10cm with or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed. |
| 50 | S&F aluminium (die cast body) door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg, complete all as specified and directed. |
| 51 | S&F pressed steel frame for doors with one rebates size of frame 105x60 mm including necessary fixing lungs hinges lock strike plate etc. including PCC, 1:3:6, type C-0 (using 12.5 mm graded crushed stone aggregate) as in back filling of pressed steel frame, complete all as specified and directed. |
| 52 | S&F 30mm thick 2nd class hardwood, factory made, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a), complete all as specified and directed. |
| 53 | S&F 125mm long medium weight, cold rolled mild steel Butt hinges, complete all as specified and directed.. |
| 54 | S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed, complete all as specified and directed. |
| 55 | S&F 300mm mild steel ordinary rat tail pattern springs for door including rollers and roller plate, complete all as specified and directed. |
| 56 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying and fixing in opening, complete all as specified and directed. |
| 57 | S&F 30mm thick Factory made Solid Panel PVC Door Shutter (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing, complete all as specified and directed. |
| 58 | S&F 100mm long medium weight, cold rolled mild steel Butt hinges, complete all as specified and directed.. |
| 59 | S&F 150mm size Aluminium anodised, barrel tower bolts of extruded section, complete all as specified and directed. |
| 60 | S&F 150mm size Aluminium anodised, handle of extruded section, fabricated type, anodised and fixed, complete all as specified and directed. |
| 61 | S&F solid PVC wall Lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame including 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC Frame as per specifications,complete all as specified and directed. |
| 62 | S&F 1000 litres capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic bal screwed for iron pipe (minimum weight 210 gms) including dismantling existing water tank and removing from site, complete all as specified and directed. |
| 63 | S&F in repairs for 15mm bore tubes, medium grade, galvanised, with all fitting, (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc.) and fixed complete to and ceiling with clips, wall hooks, wooden plugs or laid in floors including screwing and waste and for forged bends on piping as required, complete all as specified and directed. |
| 64 | S&F in repairs for 20mm bore tubes, medium grade, galvanised, with all fitting, (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps, plugs, unions etc.) and fixed complete to and ceiling with clips, wall hooks, wooden plugs or laid in floors including screwing and waste and for forged bends on piping as required, complete all as specified and directed. |
| 65 | S&F in repairs 15mm bore pillar tap, cast copper alloy quarter turn, chromium plated, fancy type, CP screwed down high pressure, complete all as specified and directed. |
| 66 | S&F in repairs 15mm bore Stop valve / angle valve, cast copper alloy, chromium plated, fancy type, screwed down high pressure with capstan head, complete all as specified and directed. |
| 67 | S&F in repairs 15mm bore bib tap, cast copper alloy, chromium plated, fancy type, long body with crutch or butterfly handle, screwed for iron pipe or for brass ferrule, complete all as specified and directed. |
| 68 | S&F in repairs 15mm bore shower roses chromium plated with chromium plated arms, complete all as specified and directed. |
| 69 | S&F in repairs 15mm size PVC connections with PTMT nuts of length 450mm, complete all as specified and directed. |
| 70 | S&F in repairs stainless steel soap dish fixed to wall with plug and screw, complete all as specified and directed. |
| 71 | S&F in repairs 20mm dia Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified and directed. |
| 72 | S&F in repair 600mm long towel rail of PTMT fixed with and including chromium plated brass screw and wooden / plastic cleats(minimum weight 190gms), complete all as specified and directed. |
| 73 | S&F in repairs 10 litre capacity PVC valveless, Syphonic action type, flushing cistern low level, white with inlet ball valve, float and handle including brackets and PVC flush pipe etc., complete all as specified and directed. |
| 74 | S&F in repairs vitreous china wash hand basin, white flat back, size of 550x400mm including cutting for and pinning in ends of brackets (including supply and fixing of brackets) or erecting stand, 32mm brass chromium plated waste fitting with long screwed shank and fly nut flanged end bedded in red led cement, chain and plug and porcelain stopper, complete all as specified and directed. |
| 75 | S&F in repairs for 600mm x 450mm bevelled edge mirror of selected quality glass mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers, complete all as specified and directed |
| 76 | S&F in repairs 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or fixed to walls, complete all as specified and directed |
| 77 | S&F in repairs 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or fixed to walls, complete all as specified and directed |
| 78 | S&F in repairs 100/75mm outlet PVC (SWR) floor trap with chromium plated grating including Jointing to waste pipe and fixed in cement concrete 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate), complete all as specified and directed. |
| 79 | S&F 75mm size PVC (SWR) bends of any radius, complete all as specified and as directed. |
| 80 | S&F 75mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door, complete all as specified and directed. |
| 81 | S&F 110mm size PVC (SWR) bends of any radius, complete all as specified and as directed. |
| 82 | S&F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door, complete all as specified and directed. |
| 83 | S&F 75mm bore PVC (SWR) vent cowl, complete all as specified and directed. |
| 84 | M&L for plain cement concrete, 1:3:6, Type C-1 (using 20mm graded crushed stone aggregate) as in surface channel, drain and RCC post etc. including necessary form work, complete all as specified and as directed. |
| 85 | M&L for Extra over for forming fair finished to drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred / stopped ends etc., complete all as specified and directed. |
| 86 | M&L for 75mm thick plain cement concrete, 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in sub base, complete all as specified and directed. |
| 87 | M&L for 100mm thick plain cement concrete, 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in flooring , laid in alternate bays and finishing the surface even and smooth without using extra cement, complete all as specified and as directed. |
| 88 | M&L for 60mm thick machine pressed precast concrete interlocking paver block any shape and size confirming to IS-15658-2006, M-35 with grey cement and pigment over and including including 50mm thick compacted bed of fine sand, complete all as specified and direction. |
| 89 | Schedule 'A' Part-II (E/M Work) |
| 90 | M&L for Point wiring for light / fan point controlled by one way switch 6 Amps 240 volts with 1.5 sqmm copper conductor FRLSH (multistrand) PVC insulated ISI marked unsheathed copper wire 1100 volt grade in and including concealed conduit, non metalic rigid PVC medium grade ISI marked conduit not less than 19 mm with all fittings & other accessories and also including PVC insulated ISI marked unsheathed FRLSH copper wire cable 1100 volts grade of size 1.5 sqmm copper conductor as earth wire to common earth dolly including concealed in wall / ceiling, modular MS box with modular cover plate with frame suitable for modular switches, sockets, fan regulator etc for the following :- Note - Colour code of cable Phase-Red, Neutral- Black and Earth -Green) |
| 91 | All as per Ser item No 88.00 here in above but fan point controlled by one switch and regulator |
| 92 | All as per Ser item No 88.00 here in above but 3 pin 6 Amps switch socket outlet point on independent Board. |
| 93 | All as per Ser item No 88.00 here in above but 3 pin 6 Amps switch socket outlet point on same board. |
| 94 | All as per Ser item No 88.00 here in before but wiring with 2.5 sqmm multi stranded cable and earth wire with copper conductor of size 2.5 sqmm for 15 Amps power point. |
| 95 | S&F Modular switch 1 way, 6 Amp, 230 volts ,1 Module, complete all as specified and directed. |
| 96 | S&F modular Socket 6 Amp, 230 volts, 5 Pin universal, 2 Module, complete all as specified and directed. |
| 97 | S&F Modular switch 1 way, 16 Amp, 240 volts ,1 Module, complete all as specified and directed. |
| 98 | S&F Modular socket 6/16 Amp, 250 volts, 2 Module, complete all as specified and directed. |
| 99 | S&F Ceiling rose, surface bakelite 65 x 50 mm, 3 terminals fixed on PVC Round Block, complete all as specified and directed. |
| 100 | S&F modular step type fan regulator suitable for 120 watt 250 volts, 2 Module, complete all as specified and directed. |
| 101 | S&F 20 Watt LED batten extruded Al body with PC diffuser in unique square shape > 120 degree wide distribution,, 4 feet, minimum efficacy 120 lumen / watts LED batten 4 feet 20 W, CCT 6500 K complete including connection upto ceiling rose with flexible copper twin twisted wire, complete and all as specified and directed. |
| 102 | Sub main wiring with two runs of single core PVC insulated multistranded un-sheathed FRLS cable of size 6.0 Sqmm with stranded copper conductor, drawing into concealed PVC conduit / surface batten (including PVC conduit of requisite dia and accessories) with one run of continuous PVC insulated multistranded unsheathed FRLS cable earth wire of size 6.0 Sqmm (in green volour), complete all as specified and directed. Note : Note :2 runs of 6 sqmm copper cable & 1 run of 6 sqmm copper cable in and including 25mm PVC conduit shall be measured as one unit. |
| 103 | S&F MCB of single poles and current carrying capacity 6 to 32 Amp, 240V, 10 KA 'B' curve, in the MCB DB complete with connection testing and commissioning, complete all as specified and directed. |
| 104 | S&F MCB triple pole and neutral ISI marked, B series, working on 415 volts 50HZ AC supply for incoming and outgoing controlling system capacity 40 Amps, 10 KA breaking capacity, complete all as specified and directed. |
| 105 | S&F sheet metal enclosure distribution board, double door type, as per IEC 61439-3 (CRCA sheet) dust and vermin proof MCB DB, TPN 4 way with 200 Amps rated copper busbar, 415 Volts with in built MCCB 160 Amps, 16KA, 2 neutral bar and 2 earth bar IP 54 protection, cable ties for cable management (fully insulated busbar and shrouded neutral bars), reversible door for IP 43 & IP 54, flush mounted to wall, complete all as specified and directed. |
| 106 | S&F epoxy powder coated or polystrene insulated material sheet metal enclosure, factory made, (double door) 8 way single pole & neutral suitable for MCB DB's 240 Volts with 200 Amps rated busbar, neutral & earthing link bar, flush/surface mounting, complete all as specified and directed. |
| 107 | S&F ceiling fans complete with blades, down rods, electronic regulator and accessories 230V, 1200 mm sweep, minimum air delievery 210 CFM with service value 6.00, BEE 5 star rated with brushless direct current motor (BLDC), complete all as specified and directed. |
| 108 | S&F of Exhaust fan, made of sturdy Engineering steel body, complete with louvers shutter, 450mm sweep, voltage 230V, 50 Hz, RPM 1200, copper winding, including connection with 1.5 sqmm mutistrand copper conductor flexible wire from ceiling rose, including outside louvers with proper hole, and necessary fixing arrangment and making good to disturbed surfaces, complete all as specified and directed . |
| 109 | M&L for earthing complete with galvanized steel earth plate electrode 600mm x 600mm x 6mm buried directly in ground (earth pit not less than 2.25 metre deep below ground level) vertically, with top edge of the plate not less than 1.25 mtr below normal ground level, connected to galvanized iron wire 4mm dia by means of nuts, bolts, washers of GI steel all as shown on electrical plate No 3 of MES Schedule Part I connected to earthing test point and testing on completion with and including necessary excavation and earth work, earth electrode, earthing lead from electrode to equipment/substation, adequate quantity of charcoal dust and common salt, test point, PCC (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) for earth pit with 40 x 40 x 6mm mild steel angle iron frame for cover, pre cast RCC (1:2:4) type B-1 (using 20mm gradedcrushed stone aggregate) 40mm thick cover, reinforced with 6mm dia bars 3 Nos both way with 12mm dia round bar handle, GI light grade watering pipe 15 mm dia with funnel and wire mesh, and 40 mm dia GI light grade earth lead protection pipe, complete all as specified and directed.Note: (i) The unit rate includes main earthing lead/strip from earth electrode to test point up to 7.5 meter (ii) In case measured value of earth resistance is recorded more than 1.0 ohms then the earthing shall be re done by the contractor without any extra cost to the department. |
| 110 | S&F LED luminaire 600mm x 600mm, 35/36 Watt, 220V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holder & LED lamp suitable for roof ceiling including connecting up with driver three core flexiable copper conductor cases of suitable size, complete all as specified and directed. |
| 111 | Excavation in trenches, n. exc 1.5 m wide and n. exc 1.5m depth and getting out in for foundation of pole, stay, laying of cable and pipe in any type of soil etc all as specified and directed |
| 112 | Returing, filling in incl spreading, levelling, watering and well ramming in layers n exc 25cm thick after laying of the cables,jointing & testing complete all as specified and directed. |
| 113 | Removing excavated material to a distance n.exc 50 m & depositing where directed at a level n. exc 1.50 m above the starting point, complete as specified and directed. |
| 114 | S&F 90mm bore dia DWC (double wall corruguated) pipe conforming to IS: 14930 / IS 16205 for protection of HT / LT Cable including necessary snap fit coupler required for fixing, complete all as specified and directed. |
| 115 | S&F 50mm bore dia DWC (double wall corruguated) pipe conforming to IS: 14930 / IS 16205 for protection of HT / LT Cable including necessary snap fit coupler required for fixing, complete all as specified and directed. |
| 116 | Supply, laying, jointing and testing XLPE insulated of cross sectional area 95 Sqmm 3.5 Core, PVC inner sheathed, armoured with galvanised steel strip or wire, heavy duty, LT underground cable ISI marked with aluminium conductor 1100 volt grade laid in trenches / duct passing through pipe / duct or fixed on pole and connecting and testing etc., complete all as specified and directed. |
| 117 | Supply, laying, jointing and testing XLPE insulated of cross sectional area 50 Sqmm 3.5 Core, PVC inner sheathed, armoured with galvanised steel strip or wire, heavy duty, LT underground cable ISI marked with aluminium conductor 1100 volt grade laid in trenches / duct passing through pipe / duct or fixed on pole and connecting and testing etc., complete all as specified and directed. |
| 118 | Supply, laying, jointing and testing XLPE insulated of cross sectional area 25 Sqmm 4 Core, PVC inner sheathed, armoured with galvanised steel strip or wire, heavy duty, LT underground cable ISI marked with aluminium conductor 1100 volt grade laid in trenches / duct passing through pipe / duct or fixed on pole and connecting and testing etc., complete all as specified and directed. |
| 119 | M&L for copper earthing complete with 600mm×600mm×3.15mm thick electrode, buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level, connected to 20×3mm copper strip as earthing lead by means of bolts, nuts, check nuts and washers of copper all as shown in electrical plate No. 3 connected to earth test point & to main switch board with & including adequate quantity of charcoal dust and common salt alround earth plate & 40 mm dia GI pipe medium grade for earth lead protection pipe for suitable length and GI pipe 20 mm dia medium grade for watering pipe with funnel & wire mesh including necessary earth work and PCC (1: 3 : 6) type C-1 for earth pit , internal surface of concrete shall be given 10mm thick plaster in CM 1:4 and 40 mm thick precast RCC cover 1 : 2 : 4 ,type B-1( using 20 mm graded crushed stone aggregare ) reinforced with 8 mm dia TMT bars @ 75 mm c/c both ways with 12mm dia round bar as in handle, complete all as specified and directed. NOTE : (i) The cost of earth lead and its protection pipe upto and including 7.5 m only from the top of earth electrode are deemed to be included under this item and additional earth lead , if any, required at site shall be measured and paid for separately under appropriate item of Schedule `A’/BOQ.(ii) Any joint in earth lead from earth electrode to test point shall not be allowed/permitted. |
| 120 | Supply and installation, testing, commissioning, factory made, CPRI approved, outdoor type, LT Feeder pillar board (kiosk type), confirming to IS 5039 with IP-54 protection, made out of 3.15 mm thick CRCA sheet , 415 Volt, 3 phase , 50 HZ supply, mounted on and including MS angle section 50 x 50 x 5 mm frame with front openable, double door with provision of locking arrangement dust & varmin proof , gasket, TPN busbar shall be insulated with colour coated heat shrinkable sleeves and shall be mounted on proper insulator, gland, welding hinges of dust proof, overall powder coated, including taking down old Feeder pillar board complete all as specifed and directed & Connisting of the following switchgear:- Please Enable Macros to View BoQ information |
| 121 | Supply and installation, testing, commissioning, factory made, CPRI approved, outdoor type, LT Feeder pillar board (kiosk type), confirming to IS 5039 with IP-54 protection, made out of 3.15 mm thick CRCA sheet , 415 Volt, 3 phase , 50 HZ supply, mounted on and including MS angle section 50 x 50 x 5 mm frame with front openable, double door with provision of locking arrangement dust & varmin proof , gasket, TPN busbar shall be insulated with colour coated heat shrinkable sleeves and shall be mounted on proper insulator, gland, welding hinges of dust proof, overall powder coated, including taking down old Feeder pillar board complete all as specifed and directed & Connisting of the following switchgear:- Please Enable Macros to View BoQ information |
