|
| 1 | Clearing grass and removal of the rubbish including clearing of jungle and uprooting of rank vegetation, shrubs, bushes, trees upto 300mm girth measured 1.00 metre above ground level and in-equalities which includes removal/levelling of boulder/blasted/crushed rock upto a depth of 300mm under the pipe rack or under the fire water line or in between the drain and footpath or any other area inside the plant premises either mechanically or manually and disposal of rubbish up to a distance of 150 m outside the periphery of the area cleared as per the direction of EIC. |
| 2 | Earth work in over areas/foundation/Pits/Trenches etc. by mechanical means (Hydraulic excavator) / manual means/controlled blasting to required profile, level, grade, camber, etc in all soils/strata as mentioned below upto 1.5meter depths, including dressing of excavated sides and ramming of bottoms and disposal / stacking of excavated materials within NFC campus for all leads and all inherent lifts and filling in layers with available earth in the NFC not exceeding 150m, watering, consolidation etc. complete all as per specifications, drawing and as directed by Engineer-in-charge.Note: Excavation to be done at certain distance for tree plantation, area grading or for any other purpose required as per the diection of EIC. |
| 3 | Filled up rock/Boulders/Crushed rock/Soil |
| 4 | Hard rock (by chiselling or wedging or rock hammer and cutter or hydraulic splinter or controlled blasting/by using machine/ such as poclain with jack hammer or controlled blasting or by approved chemical method as directed by EIC. |
| 5 | Lead charges for all additional leads over the initial lead of 150 m by mechanical transport, including loading. unloading, stacking, the disposable soil, rock, debris etc within NFC Plant premises.Note: measurement of lead charges wlll be based on truck measurement with a deduction of voids @ 20% and 50% for soils and rock/debris respectively. |
| 6 | Supplying, stacking and levelling of good earth black or red soil at NFC Campus including the cost of excavation, loading, unloading at site, royality from outside and complete as directed by Engineer-in-charge including levelling, neatly dressing, rolling and watering as per specification (earth measured in stacks will be reduced by 20% for payment).Note :- 1. Earth to be approved by EIC before supplying and shall be suitable for landscaping.2. Earth to be dumped near the pipe rack or near the fire water line or near the drain and footpath as per the direction of EIC for spreadding mechanically or manually under those areas. |
| 7 | Plain/Reinforced Cement Concrete with Nominal Mix 1:1.5:3 using Portland Pozzolana Cement conforming to IS 1489 Part-1 (M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, Andhra Cements Ltd., KCP make) with river/ manufactured/robo sand and graded stone aggregates of 20mm maximum size at all depths/heights below/above plinth level including pumping, laying in proper line, slope, level, profile, consolidation, finishing smooth/broom finish as applicable, curing,etc., complete as specified and directed. |
| 8 | Providing centering and shuttering using 12mm thick marine plyboard at all depths and heights below and above plinth level, vertical, horizontal, inclined,circular including strutting, propping using steel pipes/acro stagging, removal, cleaning of the same for insitu reinforced cement concrete and in plain cement concrete work, pockets for machine/equipmet foundations as required including chamfers, splays, keys, wedges, nails, bracings, brackets and applying one coat of shuttering oil on all shuttering surfaces coming in contact with concrete etc., complete as directed.Note :- Plywood shall not be used for more than eight repitions. |
| 9 | Brick work using quality flyash bricks of class designation 7.5 or more conforming to IS 12894 using cement mortar 1:4 (1 cement :4 using crushed stone sand of grade conforming to BIS 2116) at all depths below/Above plinth level in foundation and in plinth, storm water drains, etc., simultaneous pointing with same mortar below ground level, and ranking out joints above ground level, curing,steel/ tubular scaffolding etc., complete as per specifications and as directed by E.I.C. |
| 10 | Cement plastering 15 mm thick for external walls using ready made plaster in cement mortar (1cement:4 Sand) of make M/s Enduraplast, Walplast, Ultratech or approved equivalent fininshed smooth at all height above plinth level over brick walls or concrete surface including making necessary grooves in between junctions or brick masonary and RCC , providing & fixing GI plaster mesh/chicken mesh 150 mm wide along route of walls chipped for service lines, junction between RCC and brick walls and also other places wherever required over brick walls or concrete surface, preparation of surface, hacking of surface, steel/tubular scaffolding curing etc., complete as specified and directed. |
| 11 | Painting exterior walls/surfaces with two coats of antifungus and acrylic emulsion paint of exterior quality having 100% acrylic Asian Paint Ultima Protek/Dulux Professional weathershield flex or any other approved brand and shade including preparing surfaces, filling cracks/holes with external crack filler of Fosroc renderoc CS/CF or any approved equivalent, applying one coat of approved primer as per manufacturers specification, curing, scaffolding, cleaning, etc., complete.Note:- 1. Rates should be qouted inclusive of one coat of primer, minimum two or more coats of paint and removal of old paint by using scrubbing machine if required, preparing the surface smooth including necessary repairs to scratches etc. complete is also included.2. Rates are inclusive of scaffolding required at all heights. |
| 12 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete including two coats of approved primer and two coats of ready mix paint as per IS 164 etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). |
| 13 | Random rubble masonry with near by available hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size)using Portland Pozzolana Cement conforming to IS 1489 Part-1 (M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, Andhra Cements Ltd., KCP make) up to required level with Cement mortar 1:6 (1 cement : 6 coarse sand) as directed by EIC.Note: -Stones are available inside the campus at free of cost. Contractor has to transport the available stones within the plant premises to the place of work which includes the breaking of stone as per the requirement. |
| 14 | Providing Raised and Cut Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) including preperation of surface complete as specified and directed. |
| 15 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns(Grass block pavers), drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.Minimum60mm thick cement concrete paver block/Grass block pavers of M-35 grade with approved colour, design & pattern. |
| 16 | Providing and laying matt finished vitrified tile of size 100x100x16mm having water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in out door floors such as footpath, court yard multi models etc., laid on 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) in all shapes & patterns including spacers and grouting the joints with epoxy grout of matching pigments etc. complete as direction of Engineer-in-Charge. |
| 17 | Providing and fixing 100mm x 100mm x 75mm granite stone block/cobble hand cut and chisel dressed on the top, for paving in floors, drains etc. laid over 20mm thick base mortar 1:4(1 cement:4 coarse sand) with joints 10mm wide filled with same mortar including ruled pointing etc. complete as per directin of engineerin-in-charge. |
| 18 | Providing and laying gang saw cut 30 mm thick, mirror polished pre moulded and pre polished/leathered/honed finish (or in combination) machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups,moulding, nosing etc. complete as per direction of Engineer-in-Charge.With granite stone of colour black, cherry/ruby red or any other color/texture as approved and directed by EIC. |
| 19 | Providing and laying gang saw cut 18 mm thick, mirror polished pre moulded and pre polished/leathered/honed finish (or in combination) machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups,moulding, nosing etc. complete as per direction of Engineer-in-Charge.With granite stone of colour black, cherry/ruby red or any other color/texture as approved and directed by EIC. |
| 20 | Providing and laying machine cut chissel dressed kota stone slab of approved shade in floor, tread, landing, riser, skirting, dado over and including a bed of cement mortar including preparing the base surface, applying neat cement slurry @ 2.75 Kg of cement per Sq.m. of area to receive the mortar, providing neat cement slurry @ 4.4kg. of cement /Sq.m. of area over the mortar bed, jointing each slab with neat cement paste/ grouting white cement and pigment ( conforming to IS : 2114, Table-1, matching the shade of slabs), machine cutting of the slab edges square, true & plumb finishing, grinding, polishing, finishing etc. all complete. |
| 21 | 25mm thick kota stone slab (with tolerance +_2mm for thickness, +_2mm for length/ breadth) in floor tread, landing, riser, skirting, dado over 20mm thick cement mortar 1:4(1 Cement : 4 coarse sand by volume) for floor/tread/landing and 12mm thick cement mortar 1:3(1 Cement : 3 coarse sand by volume) for dado/skirting/risers etc. |
| 22 | Providing and fixing granite kerb stones of approved colour and quality (mirror polished or flame cut as per the direction of Engineer-In-Charge), machine-cut to required size including making curve (typically 450 mm × 300 mm × 100 mm or as approved by E-I-C), set in cement mortar 1:3 (1 cement : 3 coarse sand) on a concrete bed of 1:1.5:3 (100 mm thick).Kerbs to be neatly jointed, true to line and level, and joints filled flush with cement mortar. Granite stones must be uniform in colour, free from cracks and weathering defects, and edges should be chamfered where specified.The rate shall include materials, cutting, dressing, transport, handling, setting, bedding concrete and shuttering, mortar, curing, and all labour for completing the item as per direction of Engineer-in-Charge. Please Enable Macros to View BoQ information |
| 23 | Providing and fixing granite kerb stones of approved colour and quality (mirror polished or flame cut as per the direction of Engineer-In-Charge), machine-cut to required size including making curve (typically 450 mm × 300 mm × 100 mm or as approved by E-I-C), set in cement mortar 1:3 (1 cement : 3 coarse sand) on a concrete bed of 1:1.5:3 (100 mm thick).Kerbs to be neatly jointed, true to line and level, and joints filled flush with cement mortar. Granite stones must be uniform in colour, free from cracks and weathering defects, and edges should be chamfered where specified.The rate shall include materials, cutting, dressing, transport, handling, setting, bedding concrete and shuttering, mortar, curing, and all labour for completing the item as per direction of Engineer-in-Charge. Please Enable Macros to View BoQ information |
