|
| 1 | Laying and Jointing PVC Pipe. Heading |
| 2 | Brick work in C.M 1:5 mix including all labour charges etc complete |
| 3 | Brick work in C.M 1:5 mix using 2nd class ground moulded chamber burnt bricks with including cost and conveyance of all materials and including all labour charges etc complete |
| 4 | Plastering in C.M 1:5-12 mm thick with including cost and conveyance of all materials and including all labour charges etc complete |
| 5 | Plastering in C.M 1:5-12 mm thick with including cost and conveyance of all materials and in |
| 6 | b) CI bend 22.5° (250mm dia) |
| 7 | Construction of chamber for 100mm sluice plates |
| 8 | Construction of chamber for 100mm sluices valve |
| 9 | Supplying, Conveying and fixing spls. Including ea |
| 10 | Supplying, Conveying and fixing spls. Including eart |
| 11 | Construction of chamber for 100mm sluice plates |
| 12 | Construction of chamber for 100mm sluices valve |
| 13 | Laying and Jointing PVC Pipe. Heading |
| 14 | Plain Cement Concrete 1:4:8 (one cement four fine aggregates and eight coarse aggregates) using |
| 15 | Brick work in C.M 1:5 mix using 2nd class ground moulded chamber burnt bricks with including cost |
| 16 | Construction of chamber for 100mm sluices valve |
| 17 | Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201. |
| 18 | Earth work in all kinds soil or ordinary soil in embankment, roads with M.D.D. not less than 1.44gm/1.65gm per cc upto 3mtr high & top 0.5mtr below sub-grade level respectively with initial lead & lift from borrow pit 5m. away from the toe line of final section including rough dressing , breaking clods to maximum 5cm to 7cm & laying in layers not exceeding 0.23m in depth etc. including removing all debrises & benching old embankment complete (As per item 2(d) of AR-2006 Page-3). With mechanical lead upto 1000m |
| 19 | Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement as per MORD technical Specification Clause 301 and direction of the Engineer in Charge (excluding cost of excavation and transportation to site). |
| 20 | Fine dressing and turfing including transportation by mechanical means with all lead and lift and placing of turf in position and ramming with thapies and including watering and cost of all labour, materials etc. complete as per Clause 309 of MORD Specification and as per direction of the Engineer in Charge. |
| 21 | Construction of Granular Sub-Base (Grading III) Mterial with Stone Screening by providing well graded material, spreading in uniform layers with grader on prepared surface, mixing by mix in place method with rotavator at OMC and compacting with smooth wheel roller to achieve the desired density,complete as per MORD Technical Specification Clause 401 as per direction of Engineer-in-Charge. |
| 22 | Providing, laying, spreading and compacting graded stone aggregates to Wet Mix Macadam (WMM) specification including premixing the materialnwithb water at OMC in mechanical mixer(pug Mill) , carriage of mix material by tipper to site,laying in uniform layers with paver in sub base or base course on well prepared sub-base and compacting with smooth wheel of 80-100kn roller to achive the desired density including lighting ,barricading and maintenance of diversion etc as per Tables 400.11 & 400.12 and Technical specifications clause 406. |
| 23 | Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per MORD Technical Specification Clause 502 for low porosity surface and as per direction of Engineer-in-Charge. |
| 24 | Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503 of MoRD & as per direction of Engineer-in-Charge. |
| 25 | Providing ,laying and rolling of close-graded premix surfacing materials of 20mm thickness composed of 11.2mm to 0.9mm (Type-A) or 13.2 mm to 0.9 mm (Typa-B) aggregates using penetration grade bitumen to required line ,grade and level to serve as wearing course on a previously prepared base ,including mixing in a suitable plant ,laying and rolling with as three wheel 8-10KM static roller and finishing to required level and grades as per Techinical specification Clause 509. (By Mechanical)(Mix Seal Surfaing) |
| 26 | Construction of Roller Compacted Concrete Pavement(RCCP) with coarse and fine aggregates conforming to IS:383,the size of coarse aggregate not exeeding 25mm with minimum aggregate cement ratio of 5:1 mm and with minimum cement content of 310kg per cum,aggregate gradation to be as per Table 602.2 after blending, mixing in concrete mixture at optimum moisture content ,transporting to site, laying with wheel barrows or steel pans or with mechanical paver,compacting with 80-100 KN smooth wheel,tandem vibratory roller,to achieve,the designed flexural strength,finishing and curing as per drawings and Technical Specification clause 1502. |
| 27 | Earthwork in excavation for foundation of structures in all types of soil as per drawing and technical specification Clause 305 and 1104 of MoRD includding setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto all lead & lift, dressing of sides and bottom and back filling with excavated suitable material upto 3mt. as per direction of Engineer-in-Charge.CC road,Hume Pipe Culvert, Toe Wall, Drain etc. |
| 28 | Providing and constructing well compacted drainage layer above the subgrade of roadwork with approved quality of dust free washed coarse to medium sand as per Clauses 5.8 and 6.6 of SP:20-2002. |
| 29 | Providing and laying of Type-B(first class) bedding for laying of Hume Pipe on well compacted moorum or approved granular material as per MORD Technical Specification clause 1105(ii) and as per direction of the engineer-in-charge. |
| 30 | Providing concrete for plain / reinforced concrete in open foundation complete as per drawing and MORD technical specification Clause 800,1100,1200 and as per direction of Engineer-in-Charge. |
| 31 | Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5RCC M-25Raft & Drain Slab |
| 32 | Deck Slab |
| 33 | Rib Hunch |
| 34 | Construction of R.C.C. railing of M 25 grade in cast-in-situ with 20 mm nominal size aggregate, true to line and grade, tolerance of vertical railing post not to exceed 1 in 500, centre-to-centre spacing between vertical posts not to exceed 2000 mm as per drawing and technical specifications Clauses 800, 900 and 1208.3 |
| 35 | Providing and laying cement concrete wearing course M 30 grade including reinforcement complete as per drawing and technical specifications Clauses 800 and 1206.3 |
| 36 | Supplying, fitting and placing HYSD bar reinforcement (Fe 415) complete as per drawings and MORD technical specification Clauses 1000,1200 as per direction of the Engineer in chargeIn foundation |
| 37 | In Sub-structure |
| 38 | In Super-structure & Drain Slab |
| 39 | Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and MORD technical specification Clause 1204.3.8 and as per direction of the Engineer in charge |
| 40 | Providing and fixing 20mm thick compressible fiber board in expansion joint complete as per drawing and technical specifications including cost convyance taxes of all materials, cost of all labours, T & P required for the work etc.complete and as per direction of the Engineer -in- charge. |
| 41 | Providing and laying reinforced cement concrete NP3 pipe for culverts jointing with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets as per Clause 1100 of MoRD & as per direction of Engineer-in-Charge.1000 mm dia Single row |
| 42 | 1000mm dia Double row |
| 43 | Plain/reinforced cement concrete in sub-structure complete as per drawings and MORD technical specification Clauses 800,1200 and as per direction of the Engineer in charge |
| 44 | Providing and laying pitching with stone boulders on slopes laid over prepared filter media as per drawing and MORD technical specifications Clause 1300 and as per direction of the Engineer in charge |
| 45 | Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and MORD technical specification Clauses 614, 709, 1204 and as per direction of the Engineer in chargeWeepholes |
| 46 | Providing and fixing of typical masonry PMGSY informatory sign board with Logo as per MORD specifications and drawing. Brick masonry board with writting area 1.5mx0.9m and 0.115m border. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 of MoRD etc. complete and as per direction of the Engineer -in- charge. |
| 47 | Providing and fixing of typical PMGSY logos made of 1.6mm thick MS sheet duly stove enameled on both side with lettering and printing arrows, border etc.will be painted with ready mixed synthetic enamel paint of superior quality in required shade & colour fixed & supported on 75mmx75mmx6mmM.S.angle 3500mm long firmly fixed to the ground by means of properly foundation with M15 grade c.c. 450x450x600mm ,600mmbelow ground level as per drawings & tech. specification clause 1701 and as per direction of the Engineer -in- charge. |
| 48 | Providing and fixing of semi-reflectorised cautionary, mandatory and iformatory sign as per IRC-67 made of 1.5mm thick MS sheet duly stove white colour in front and gray colour on back with red reflective border of 65mm width & required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 fixed & supported on 47mmx47mmx12SWG sheet tube 3050mm long firmly fixed to the ground by means of properly foundation with M15 grade c.c. 450x450x600mm ,600mmbelow ground level as per drawings & tech. specification clause 1701.2.2 and as per direction of the Engineer -in- charge. |
| 49 | ii) 600mm Circular |
| 50 | Providing and fixing of semi-reflectorised direction & place identification sign as per IRC-67 made of 2mm thick MS sheet duly stove white colour in front and gray colour on back with red reflective border of 70 mm width & required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 fixed & supported on 47mmx47mmx12SWG sheet tube 3050mm long duly strenghting by 25mmx5mm flat iron on edges firmly fixed to the ground by means of properly foundation with M15 grade c.c. 450x450x600mm ,600mmbelow ground level as per drawings & tech. specification clause 1701.2.2 and as per direction of the Engineer -in- charge. |
| 51 | Providing and fixing of typical PMGSY Citizen sign board with logo as per MORD specifications and drawing. Two MS plates of 2mm thick, top & middle plate duly welded with MS flat iron 25mmx5mm size on back on edges. The flat iron frame of both plate will be welded to 2nos 75mmx75mm of 12SWG sheet tubes posts duly embeded in C.C. M-15 grade blocks of 600mmx600mmx750mm, 750mm below ground level. The top most dimond plate will be welded to middle plate by 47mmx47mm of 12SWG steel tube. All M.S. will be stove enameled on both sides. Lettering & printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quailty in required shade & colour. All sections of framed posts & steel tubes will be painted with primer & two coats of paint as per drawing clause 1701 and Annexure 1700.1 |
| 52 | Reference Pillar |
| 53 | TBM Pillar |
| 54 | Reinforced cement concrete M15 grade Kilomitre stoneof Standard design as per IRC:8 fixing in position including painting, lettering in accordance with the specifications Clause 1703 of MoRD . etc. complete and as per direction of the Engineer -in- charge.Fixing of Km. Stone |
| 55 | Fixing or 200m Stone |
| 56 | Guide Post (M-20) |
| 57 | MAINTENANCE - Routine Maintenance after completion of construction works for 1 st year |
| 58 | Routine Maintenance after completion of construction works for 2 nd year |
| 59 | Routine Maintenance after completion of construction works for 3 rd year |
| 60 | Routine Maintenance after completion of construction works for 4 th year |
| 61 | Routine Maintenance after completion of construction works for 5 th year Please Enable Macros to View BoQ information |
