|
| 1 | Demolition of cement concrete (unreinforced) of any descriptioin and in any position not other wise specifically provided complete. |
| 2 | Demolition of reinforced cement concrete in any descriptioin and in any position not other wise specifically provided complete. |
| 3 | Brickwork with subclass 'B' bricks, straight or curved on plan exc 6m mean radius, built in CM(1:4) incl demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone-work and precast concrete articles complete all as specified. |
| 4 | Ditto- item No. 3 above but except brick complete. |
| 5 | Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing), and rubbish off the premises complete all as specified and directed. |
| 6 | M&L for exterior wall tiles 8 to 10mm thick & not exc 0.18 sqm , colour & shade of tiles as approved by Engr-in-charge,set and jointed in neat cement slurry and pointed in coloured cement to match the surface etc complete all as specified and directed by Engr-in-Charge. |
| 7 | M&L granite 18-20mm thick colour as approved (of any type) work (table rubbed and polished) in floors, steps, jambs, pillars, window cills, cooking platforms or making oval shape hole for fixing of wash hand basin and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick screed bed in cement mortar 1:6 including necessary groove cutting, moulding and polishing the edges complete all as specified and directed |
| 8 | M&L granite 18-20mm thick colour as approved (of any type) work (table rubbed and polished) in for wall lining (veneering to wall) 12mm thick in cement mortar 1:3 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite including moulding and polishing the edges etc complete all as specified and directed |
| 9 | Reinforced cement concrete 1:2 :4 type B-1 using 20 mm graded stone aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves, bands and the like complete (reinforcement to be measured separately). |
| 10 | Mild steel TMT bars 10 mm dia and above as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete. |
| 11 | -ditto- all as per Item No 10 Above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders. |
| 12 | M&L 15 mm thick Ready mix plaster on brickwork or concrete surfaces of wall (external surface ) finished even and smooth including taking down cement or cement lime plaster, any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, including cutting of trees, shrubs or any type of vegitation upto and including roots up to 15 mtr height complete all as specified and as directed |
| 13 | M&L 15 mm thick Ready mix plaster on brickwork or concrete surfaces of wall (external surface ) finished even and smooth complete all as specified and as directed by engr-in-charge. |
| 14 | Dismantling posts or struts (wood, steel or RCC) any section, including taking out embedded portion and making good disturbed ground , complete all as specified and directed. |
| 15 | Dismantling of fencing wire mesh, any type, complete all as specified and directed. |
| 16 | Dismentling wrought iron or mild steel work of any description not other wise provided. |
| 17 | Excavation in post holes (or similar holes ) each n. exc 0.5 Cum in soft/loose soil, getting out,removing soil to a distance n. exc 50M , complete all as specified and directed. |
| 18 | PCC 1:2:4 type B-2 as in foundation,filling and mass concrete (using 40mm graded stone aggregates) |
| 19 | Mild steel angle iron posts and struts, MS flat iron fillet securing chain link fencing confirming to FE-290 E-165 as in fencing including cutting tops for required shape, drilling holes,bolting, notching for wire including all necessary drilling of similar work, complete all as specified and directed. |
| 20 | Supply only Chain link MS galvanisd fencing, any size or type, weight not less than 3.0 Kg/Sqm, galvanized with zinc coating of min 250 GMS of as per IS standards fixing with GI wire, icluding cutting, bending, fixing in any postiion and straining bolts etc complete all as specified and directed. |
| 21 | Fixing only chain link fencing including line wire, any mesh, size and type to any type of standards, rails, straining bolts etc. including provision of binding wire, complete all as specified and directed. |
| 22 | Mild steel round bars 10 to 12mm dia and over, Fe-410-W (Gde.E-250) quality-A or Fe 290 (Gde -E-165) cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, o complete all as specified and directed. |
| 23 | S & F in Repairs Galvanized, 2 strand, steel barbed wire 2.24 mm dia., barbed with 2 mm dia., barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossings with and provision of galvanized mild steel pins etc.as directed (each line wire to be measured). |
| 24 | Restraining & resecuring existing barbed wire of any type incl making good staples etc any type of standard rails straining bolts including securing or tying at crossings with and provision of galvanised mild steel wire staples or steel pins etc (each line wire to be measured) complete all as specified. |
| 25 | S&F MS screw bolts (machine made) with hexagonal or square heads at one ends and screwed the other, or screwed both ends, each screwed end to be fitting with washer and one hexagonal or square nut n.exc. 5cm long and dia of shank 8 to 10 mm etc. |
| 26 | M&L applying two coats of synthetic enamel paint on new steel surfaces of any description over 10cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete. |
| 27 | M&L for preparation of new steel surfaces including priming with red oxide primer and two coats of synethic enamel paint of any description n exc 10cm width or girth when unconnected with other painting or when painted in different tint complete all as directed. |
| 28 | M&L for one coats of synthetic enamel paint on old steel painted surfaces including preparation of surfaces of any description not otherwise descriped over 10 cm width or grith complete all as specified and directed. |
| 29 | M&L for applying Two or more coats of 100% Premium exterior acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new or old surfaces all as specified and directed. |
| 30 | M&L for preperation of new plasterd or unplasterd surface and applying two coats of cement base paint of approved tint over a coat of cement primer complete all as specified and as direcred. |
| 31 | S & F of repair rolled mild steel of grade Fe 410-W (Gde-E- 250) quality-A as in doors or gate of angle of other section with gusset plates, rails, braces,frame work of GRC jali, etc coplete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and incl either hooks and hinges or steel hanging door fitting and hanging; also fastening and fixing complete. |
| 32 | M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, dome, plates, chain etc, including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc, of required size, on the top of floor or the side of waist slab with suitable arrangement including taking down old SS sections. |
| 33 | Providing, fabricating, supplying and fixing of decorative name plate at main entrance gate, comprising 3–5 mm thick Stainless Steel (Grade 304) / Mild Steel base plate of approved size (approx. 300 mm × 450 mm), with brushed/mirror/matte powder-coated finish, including anti-rust treatment and exterior-grade protective coating. The name plate shall be fitted with raised 3D golden letters (25–75 mm height) made of SS with PVD gold coating / brass / metallic finish acrylic, fixed with concealed studs and epoxy adhesive to achieve 10–20 mm projection from base plate. The work shall include laser/CNC cutting (if required), decorative border design, all hardware, stainless steel fasteners, anchor bolts, alignment, complete installation at site, and making good of surrounding surfaces. All materials shall be weather-resistant, UV-stable, and suitable for external exposure complete as per instructions of Engineer-in-Charge. |
| 34 | M&L for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement : 4 coarse stone dust) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) white cement in place of ordinary cement to be used in the work, panels with groove all around as per approved pattern or design and colour including scrubbing and washing the tip layer with brushes and water to expose the stone chippings complete including takind down old plaster all as specified (Payment for providing grooves shall be made separately). |
| 35 | M&L for forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nails to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-Charge |
| 36 | Dismantaling plain or corrugated sheeting any gauge, thickness, including nainital or similar pattern roof covering all as specified and directed.. |
| 37 | S&F 2mm Fibre glass reinforced translucent sheeting plain or corrugated fixed with side lap fixed with coach screw and washer in iron gate,roof,wall etc. complete all as specified and directed. |
| 38 | S & F 0.50mm thick (including coated thickness) Pre- painted galvalume aluminum zinc coating GI based steel sheet of required colour and design having tensile strength of 550 Mpa as in roof, wall cladding, north light curves, fixed with zinc coated self drilling fastener including EPDM washer complete laid with side laps and end lap laid to slope all as per manufacturer/ profile maker instruction complete all as specified and directed. |
| 39 | M & L for precast reinforced cement concrete jallies 30-45 mm thick including all mouldings type B-0 1:2:4 (12.5mm graded stone aggreagte) set in cement mortar 1:4 including taking down Old RCC Jallies complete all as specified. |
| 40 | Supply only 40mm thick Sand filling under floors or in Foundation including watering & consolidation etc complete all as spd. |
| 41 | M&L machine pressed precast rubber mould coloured concrete interlocking paver blocks of 60 mm thick any shape and size conforming to IS 15658-2006 ,M-35 grade with grey cement and no pigment over complete all as specified and directed. |
| 42 | M & L 25 mm thick Endura tac tiles , dense durable and abrasion resistant Tac liner metro yellow/Tac liner yellow or tack button terracota/Tac button yellow colour as approved by GE , (Square or rectangular) area of each tile exc 0.08 Sqm but n exc 0.18 sqm in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the tiles laid over and including 15 mm thick screed bed or bedding layer of cement mortar (1:4), complete all as specified and directed. |
| 43 | M&L for 75 mm thick PCC1:4:8 type D-2 using 40mm graded as in sub base of floor (40 mm graded stone aggregate), finishing even and smooth without using extra cement to received tiles including necessary form work etc complete all as specified and directed. |
| 44 | S&F Factory Made 18mm thick 100% Solid WPC Jali (Wood polymer Composite) design of Jali as approved, comprising of virgin PVC resin of K Value 57-60 (Suspension Grade), Calcium Carbonate and natural Fibers ( Wood Powders/ rice husk/wheat husk) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded (Inner) with density not less than 650 kg/cbm Certified Company, having good screw holding capacity (Screw Withdrawal strength of 2000 N (Face) & 1100 N (Edge), Minimum Compressive Strength of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/Borer Free. Water/ Moisture Proof, Fire Retardant and fixing with stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. All as per direction of Engineer -In-Charge, Material test certificate and authentication should be compulsory provided by the manufacturing compancy. |
| 45 | S&F Frame work of WPC Size of frame 75 mm x 50 mm all as per directions of Engr-in-Charge. |
| 46 | S&F of Angle Iron frame work for fixing of frames of Jali, Grill, Gratings, claddings and other similar works as directed by Engr-in-Charge. Please Enable Macros to View BoQ information |
