|
| 1 | Schedule-A |
| 2 | Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises completed all as specified and as directed by Engr-in-Charge. |
| 3 | Demolition of cement concrete of any description as in ground floor and paving exc 15 cm thickness(below or above ground level) all as directed by Engr in charge |
| 4 | M&L for pre cast Kerb stone with plain fair faces 300x150x300 mm depth of PCC 1:1 ½ :3 of shape as approved incl all excavation, embedding in ground and removing surplus spoil upto 50 Mtr distance completed all as specified and as directed by Engr-in-Charge. |
| 5 | M&L machine cut broken stone of gauge not exc 63mm as in hard core N EXC 150mm thick spread and levelled including watering & ramming all as directed by Engr-in-Charge. |
| 6 | M&L for providing 75mm thick cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base of floor complete all as specified and directed by Engr-in-Charge. |
| 7 | M&L for Chequered cement concrete tiles 300x300x25mm thick, set jointed and pointed in near cement slurry in floors with gray cement and pigments in any colour machine preassed glazed , over cement screed bed 15mm thick cement motor 1:6 all as specified and as directed by Engr-in-charge.make nitco/arena or equivalent all as specified and directed by Engr-in-Charge. |
| 8 | M&L for 60 mm Machine pressed pre casted pressed cement concrete interlocking paver blocks with grey cement and no pigment of any shape and size conforming to IS- 15658-2006, strength not less than M-35 grouted with clean dry fine sand including 25mm thick sand cushioning all as directed by Engr-in-charge. |
| 9 | M&L for 100mm thick Cement concrete 1:2:4, type B-2 using 40 mm graded stone aggregate as in path finished even smooth with broom finished without using extra cement, laid in alternate panels with 8mm wide full depth joints duly filled with sealing compound Gde-A complete all as specified and directed by Engr-in-Charge. |
| 10 | M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete complete all as directed by Engr-in-Charge. |
| 11 | M&L joint free glazed ceramic coloured tiles in vertical surfaces of size exc .05 sqm and n.exc 0.18 sqm and 7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engr-in-Charge |
| 12 | M&L Non Skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed by Engr-in-Charge |
| 13 | Cutting and grinding mirror polishing old kota stone flooring including applying cement slurry to fill the existing joints completed all as specified and as directed by Engr-in-Charge. |
| 14 | Taking out the existing paver blocks of any size and set and jointed again in the same position after cleaning of grass and other vegitation etc all as directed and specified by engr in charge. |
| 15 | Removing existing roof treatment and preparing surface to the entire satisfaction of Engineer-in-Charge/ GE including taking down existing plaster, cleaning of all foreign material such as grass roots dust etc and roughening the concrete surfaces by wire brushes and washing down to remove dust etc flushing at junction of parapets complete and removing the same to he places where directed by Engineer-in-Charge |
| 16 | M&L for 40mm thick cement concrete type B0, 1:2:4 (20 mm graded aggregate) as in floor/roof including waterproofing compound including finishing cement concrete using extra cement |
| 17 | M&L Providing cement concrete type B 1:2:4 (12.5mm graded stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edges in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed |
| 18 | M&L for rendering 15mm thick on fair faces of brick and concrete surface in CM 1:4 mixed with WPC finished even and smooth without using extra cement all as specified (WPC will be measured and paid separately) |
| 19 | M&L apply evenly a priming coat with bituminous primer at 4 kg per 10 sqm |
| 20 | M&L APP based polymeric membrane minimum weighing 3kg/sqm minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application with overlapping 150mm complete all as specified |
| 21 | M&L preparation of surface and applying two coat of aluminium paint on APP membrane, over 10 cm in width or girth not otherwise described complete all as specified and as directed |
| 22 | Supply only Liquid water proofing compound of approved quality |
| 23 | Dismantling of brick work built in cement mortar including all quions, arches, pillars, etc. completed all as specified and as directed |
| 24 | M&L for Brick work with sub class B bricks straight or curved on plan exc 6 mtr mean radius built in CM 1:6 completed all as specified and as directed |
| 25 | All as item No 23 here in before but using old serviceable bricks retrieved from dismantling. |
| 26 | Taking down cement plaster, any description on brick walls or on concrete surfaces including racking out Joints, hacking for Key, scrubbing down with Water, etc., and removing same from the Site(s), complete all as specified and as directed. |
| 27 | M&L for rendering 15 mm thick on fare faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement all as specified (WPC measured and paid separately) |
| 28 | M&L for rendering 10 mm thick on stone surfaces or surface other than fair face of brick work or other side of lathing in cement mortar 1:6 finished even and smooth without using extra cement all as specified |
| 29 | M&L for rendering 5mm thick in cement motar 1:3 on ceiling like chhaja, roof projection facia etc on concrete surfaces, finished fair & even without using extra cement completed all as specified and as directed |
| 30 | M&L for preparing of new plastered surface of walls, applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/ltr and UV resistance as per IS 15489 : 2004 Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied & .90 ltre/10 Sqm as directed by Engr-in-Charge (Note- work will be strictly executed by mechanised means/tools as required for smart periodical services) |
| 31 | Preparing Newly Plastered Surfaces of WALLS and applying TWO COATS of DISTEMPER OIL EMULSION (OIL BOUND WASHABLE DISTEMPER) over a Coat of CHALK WHITING, complete all as specified and as directed. by Engineer-in-Charge. |
| 32 | M&L for prepraing new surface of plaster on ceiling and applying two coat of white wash complete all as specified and directed by Engr-in-Charge |
| 33 | M&L for prepraing old surface of plaster, washing rubbing down and stopping of painted surfaces on wall and applying two coat of cement base paint complete all as specified and directed by Engr-in-Charge |
| 34 | M&L preparing old distempered surfaces of wall by complete removal of existing treatment and applying two coat of oil emulsion distemper over Birla / JK wall putty 3mm thick complete all as specified and as directed. |
| 35 | M&L for prepraing old surface of plaster, washing rubbing down and stopping of painted surfaces on ceiling and applying two coat of white wash complete all as specified and directed by Engr-in-Charge |
| 36 | Dismantling mild steel work of any description not otherwise provided completed all as specified and as directed by Engr-in-Charge. |
| 37 | Mild steel plates, plain or chequered, 5mm thick or over in thickness in available sizes Fe 410 W (Gde-E-250) quality-A with riveted bolt or welded etc as in duct cover & similar work completed all as specified and directed by Engr-in-Charge |
| 38 | M&L for rolled section as tubular sections as in vertical steel columns with flange plates, caps, bases, base plates, splices angle brackets, cleats, holding down bolts and nuts and other section complete of Fe 410 W E-250 grade including all welding etc, complete all as specified and directed by Engr-in-Charge. |
| 39 | S&F Framed work such as Gate,grills etc with ends of bars shoulders and / or riveted or forged into spikes, framed guard bars barred iron door ladders, framed balusters walls way, railings, frame work of water tank and similar work confirming to Fe 410-O or 310-O all as specified and directed by Engr-in-Charge. |
| 40 | S&F for MS angle iron as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc flat iron fillets (for securing with mesh etc including all necessary drilling bolting or riveting etc and similar work confirming to Fe-290 (Gde-E-165 quality-B. Note:-Posts/struts of angle iron made to shape shall be welded to existing angle iron bracket of security wall, contractor shall make his own arrangement for welding for boundary wall by using gen sets or any alternative arrangement. |
| 41 | S&F 1mm mild steel, plain black sheet hearths; covering to door shutters; covering to door chowkats (frames); chullah hoods; waters tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size, edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40mm lap joints or welded/riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required and directed. |
| 42 | M&L Preparation new or previously untreated steel surface of any description, over 10 cm in width or girth, one coat of red oxide zinc chrome primer over applying two coat synthetic enamel (ordinary tint) paint all as specified and directed by Engr-in-charge. |
| 43 | S&F in repair Galvanized 2 stand Steel Barbed wire 2.24mm dia barbed with dia barbs at 75 mm spacing and straining and fixing to any type of stsnderd rails, straining bolts,including securing or tying at crossings with and provisuion of galvanised mild steel pins, etc incl taking down of existing barbed wire as directed (each line wire to be measured) complete all as specified and directed by Engr-in- Charge |
| 44 | S&F in repair 950/650/450 mm dia (as directed by Engr-in-Charge) concertina coil reinforced punched(chrome razor or blade wire with barbed top of 0.5mm thick galvanised sheet and core wire of dia 2.5mm of high tensile steel wire incuding galvanised MS staples/ Clips for tying at crossing complete including taking down of existing concertina coil all as specified and directed by Engineer–in-Charge |
| 45 | Dismantling of plain or corrugated steel sheeting / AC sheeting any gauge thickness inculing nanital or similar pattern roof coverings all as specified and directed by Engr-in-Charge. |
| 46 | S&F 0.5 mm thick pre coated thick galvalume aluminium zink coated GI based corrougated steel sheeting of any colour having tansile strength of 550 MPA as in roof covering/glading to wall fixed with self tapping screws, complete all as specified and directed by Engr-in-Charge. |
| 47 | M&L for Chain link MS galvanised fencing, any size or type including line wires, any mesh, standartds rails, straining bolts etc including provision of binding wire all as specified and directed by Engr-in-Charge. |
| 48 | S&F 2 mm thick fibre glass reinforced translucent corrugated/ plain sheeting with two corrugations side lap fixed with L type or J-type or cranked hook botls and washer in roof, wall and similar work etc all as specified and directed by Engr-in-Charge. |
| 49 | M&L expanded metal not exc four kg per sqm, cut to length, bent to shape required and tying with and including annealed muild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members. |
| 50 | M&L for 100mm thick Cement concrete type B2 1:2:4 (40mm graded stone aggregate) as in path finished even and smooth with broom finished without using extra cement, laid in panels not exceeding 2 sqm each panel and joints shall be filled with sealing compound Gde-A, complete all as directed by Engr-in-charge |
| 51 | M&L for PCC 1:2:4 type B2 using (20mm graded stone aggregate as in cills, copings, small plates incl weathering slightly rounded or chamfered angles and throating including necessary form work complete all as directed by Engr-in-Charge. |
| 52 | Taking down steel rolling shutter and refixing with or with out ball bearing including to cover side guide rail and greasing of MS spring and side guide and make functional including complete overhaling size exc 10 sqm but nexc 40 sqm as entire satisfication of Engr-in-Charge. (Note : Supply of material to be measured seperately) |
| 53 | S&F of MS pipe medium grade of dia upto 40 mm including cutting and fixing, drilling, welding for rolling shutter all as directed by Engr-in-Charge. |
| 54 | S&F spring of high carbon spring 30mm dia drilling, welding for rolling shutter all as directed by Engr-in-Charge. |
| 55 | S&F in repair of mild steel rolling shutter strips made out of 1.25mm MS sheet including and reavting including one coat of primer and two coat of synthetic enmail paint all as directed Engr-in-Charge. |
| 56 | S & F in repairs PVC pipes single socketed in any length with rubber ring joints fixed to wall ( 110mm bore) including flat iron claimp for proper fixing complete all as specified by Engineer-in -Charge |
| 57 | S & F in repairs PVC bends 110mm dia complete all as specified by Engineer-in -Charge. |
| 58 | S & F in repairs PVC pipes single socketed in any length with rubber ring joints fixed to wall ( 75mm bore) including flat iron claimp for proper fixing complete all as specified by Engineer-in -Charge. |
| 59 | S & F in repairs PVC bends 75mm dia complete all as specified and directed. |
| 60 | S&F in repair for vitreous china wash basin white flat backsize 550x400 including cutting for and pinning in ends of brackets including fixing of 32 mm low dencity polylethyne pipes (LDPE)of pressure rating 6kg/cm2,cupling ,PVC connection with 15 mm dia PTMTcheknuts ,brackets all complete as directed by Engr in Charge. |
| 61 | S & F in repairs, 20 mm bore Tubes, `medium grade',completed all as specified and as directed by Engr-in-Charge. |
| 62 | All as per item No 60 here-in-before but 15 mm bore. |
| 63 | Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel/allmn frame glazed with putty or fixed with wooden /almn beads etc.completed all as specified and as directed by Engr-in-Charge. |
| 64 | S&F in repair 4 mm thick sheet glass,ordinary quality,in squares n exc 0.5 sq m each pane fixed to aluminium frame with rubber gasket or fixed with glass putty as required etc completed all as specified and as directed by Engr-in-Charge. |
| 65 | M&L for PCC 1:4:8 type D2 using (40mm graded stone aggregate) as in foundation ,filling and mass concrete completed all as specified and as directed by Engr-in-Charge. |
| 66 | S&F Single side writing informatory stainless steel reflecting Sign Boards size 4'x3' having with Aluminium sheet base of 2mm thickness having retro reflective tape base and front colour and matter of sign board will be furnished by Engr-in-Charge.The frame of Sign board shall be 2'' outer dia Square stainless steel pipe and having two legs of stainless steel Square pipe 9' long Each of 2'' outer dia square pipe the board shall be grouted in PCC work of size 350x350x450mm including taking down of existing complete all as specified and as directed. |
| 67 | Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out in soft / loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface all as specified and directed by Engr-in-Charge. |
| 68 | Taking down Chowkhats or frames n exc 1.5 sqm each without taking of shutter from the frame all as specifed and directed by Engr-in-Charge. |
| 69 | Taking down shutter of any discription exc 1Sqm n exc 2 Sqm each complete all as specified and directed by Engr-in-Charge. |
| 70 | Taking down shutter of any discription exc 1Sqm and n exc 2 Sqm each complete all as specified and directed by Engr-in-Charge. |
| 71 | S&F factory made 30mm thick solid core Flush door shutter with block board with BWP plywood on both side all as specified directed by Engr in Charge. |
| 72 | M&L Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and wood grain printed PVC Sheet used 5mm thick x 15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beaading of 10mm x 10mm used instead of exposed portion of PVC sheet beading for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; supplying & fixing in the frame at site as per specification & drawing. |
| 73 | Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing |
| 74 | M & L for preparation of new/old wooden surfaces of any description not otherwise described, over 10 cm width or girth and applying two coat of synthetic enamel paint over one coat of pink wood primer all as specified and directed by Engineer-in-Charge. |
| 75 | S&F stain less steel bright polished bow handle solid type 150mm grip length fency type complete all as specified and directed by Engr -in -charge |
| 76 | S&F stain less steel bright polished barrel tower bolt with plate with 10mm dia of shoot and 200mm long complete all as specified and directed by Engr-in-Charge. |
| 77 | S&F 100mm long medium grade stain less steel but hinges bright polished fix with nut and bolt complete all as specified and directed by Engr-in-Charge. |
| 78 | S&F 250mm long, 16mm dia stain less steel bright polished door sliding bolt hasp and staple type with fixing of clips 3 Nos with fixing with nut & bolt all as specified directed by Engr in Charge. |
| 79 | M&L Gunitting work for RCC work as in columns, beam, slab, perapet, chajjas etc by removing all loose concrete on the reinforcement, cleaning the surfaces with wire brushes and reinforcement with sand papers than applying apoxy paint to rusted reinforcement and S&F welded wire mesh fabric size not less than 95x95x3 mm on the prepare surfaces and finally applying guniniting 30 to 40 mm thick (average thickness )with presure gun using 1 part of cement and 3 part of coarse cement incl necessary form work where ever required all gunnited surface shall be brought in complete geometric figure even in the guniting opration only complete all as specified and directed.Note:- Where new or additional reinforcement is required the same shall be paid for separetaly of this schedule as above. |
| 80 | M&L for 6 to 8 mm dia TMT bars, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips |
| 81 | Note :- The amount of Rs 174139.00 against Schedule of Credit on Srl Page 146 shall be deducted from the total amount quoted against Sch 'A' Please Enable Macros to View BoQ information |
