|
| 1 | Repair and Rewinding of sewage/drainage electric submersible motor up to 3HP capacity single phase 420 volts AC supply 50 Hz of mody/ KSB make with suitable size of copper wire allied rewinding material including dismantling and reassembling etc, as required. Labour and cartage from site to workshop and back at site etc complete, including dismantling and installation of pump as per instruction direction and entire satisfaction of Engineer-in-charge. |
| 2 | Providing and fixing of ball bearing suitable for mody/KSB make sewage /drainage, submersible electric pump set etc, as required and as per the direction and satisfaction of Engineer in charge. : Upper bearing 10/7.5 HP as required as per the direction and satisfaction of Engineer in charge. |
| 3 | Providing and fixing of sealing rubber “O\\" ring kitset suitable for mody sewage/drainage submersible sump pump set of capacity 10/7.5 H P etc, complete as per direction and satisfaction of Engineer in charge. |
| 4 | Providing and fixing of mechanical seal T/S, V/S, T/C upper/lower suitable for sewage drainage for required 10 HP/7.5 HP As required as per the direction and satisfaction of Engineer in charge. |
| 5 | Providing and fixing of Power contractor ML 1.0/1.5 16 Amp. L&T/ BCH/Schneider or equivalent make 420 Volts, 3 phase suitable for mody sewage/drainage submersible Pump etc as required.as required as per the direction and satisfaction of Engineer in charge. |
| 6 | Providing and fixing 32 Amp. TPN MCB, of make L&T/FujifHavells including fixing charges cartage etc, as per the direction of Engineer in charge. |
| 7 | Providing and fixing 63 Amp. Four Pole MCB, of make L&T/Fuji/Havells or equivalent including fixing charges cartage etc, as per the direction of Engineer in charge. |
| 8 | Providing and fixing 9-14 Amp./20-32 Amp Overload relay DOL starter including labour charges, cartage etc, as per the direction of Engineer in charge. |
| 9 | Providing and fixing volt meter 96X96 Sq.MM (0- 500 Volt) of make A.E.(Automatic Electric)/siemens or equivalent made complete as per the direction of Engineer in charge. |
| 10 | Providing and fixing Ampere metre 96X96 Sq. MM (0-30 Amp) of make AE (Automatic Electric) ,siemens, havells or equivalent complete as per direction of Engineer in charge. |
| 11 | Providing and fixing single phase preventer of approved make L&T, Siemens, minilac etc, upto 7.5 HP, monoblock/ sewerage/ drainage pump set as per the direction of Engineer in charge. |
| 12 | Providing and fixing push button ON & OFF with element BCH/ L&T/ Vaishno make 22.5 mm dia cartage labour charge for fixing the push button i/c cartage, testing etc, as per direction of Engineer in charge. |
| 13 | Providing and fixing indicating lamp 22mm dia (Red,Yellow, Blue & Green as required) BCH make labour charges for removing & fixing the lamp i/c cartage testing etc, as per the direction of Engineer in charge. |
| 14 | Providing & fixing 150 mm dia PVC suction hose pipe for water discharge jyoti make or equivalent for 25 HP sewage discharge pump set 3 phase 440 volts 50 Hz i/e cartage, testing etc. As per direction of Engineer-in-Charge. |
| 15 | Providing & fixing 2.5 Sq mm 3 core copper conductor P.V.C control cable NationaJ/Filolex make as per IS:1554/IS694, cartage, labour charge for fixing the cable i/c casting ecc. as per the satisfaction of Engincer- in- Charge. |
| 16 | Providing and Fixing Motor starter/panel upto 10 HP BCH/L&T/Crompton/ Kirloskar/Mody or equivalent make having following specificatons:Direct on line (DOL) Starter :- 1. Overload relay - 1 No.2. Heavy Duty four pole contactor with molded coil 4. Precautions :- Phase failure, phase imbalance, phase reversal5. Short Circuit protection through MCB6. Seperate Ammeter and Volt meter7. Provision for connection dry run protection8. DOL :- Motor ON and trip indication9. Star Delta Motor ON, Trip, RYB phase indications etc. complete and entire satisfaction of Engineer - in - Charge. |
| 17 | Providing & fixing 75 mm dia cotton suction hose pipe for water discharge jyoti make or equivalent for 7.5 HP sewage discharge pump set i/e cartage, testing etc. As per direction of Engineer-in-Charge. |
| 18 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Internal work - Exposed on wall.50 mm dia nominal bore |
| 19 | Providing and fixing gun metal non- return valve of approved quality (screwed end) : 50 mm nominal bore Vertical. |
| 20 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 50 mm nominal dia Pipes. |
| 21 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stabilityfor hot & cold water supply, including all CPVC plain & brass threaded fittings and fixingthe pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the sameincluding testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc. 25 mm nominal dia Pipes. |
| 22 | Repair and servicing of Honda set pump of Capacity up to 5HP with operated with petrol/ Diesel including materil for servicing like any kind of equipment , Lubricant, oil etc dismantling and reassembling etc, as required. Labour and cartage from site to workshop and back at site etc complete, as per instruction direction and entire satisfaction of Engineer-in-charge. |
| 23 | Providing and fixing heavy duty wheel of size 30 inch (dia)or approprite available with variation for installation of PUMP having weight up to 5000kg, having stainless steel bearing in each of wheel of thermal stability for hot & cold threaded fittings and fixing the wheel with pump including , grinding, fixing and making good the same as per direction and entire satisfaction of Engineer-in-charge. Please Enable Macros to View BoQ information |
