|
| 1 | Excavation of foundation in ordinary soil/sandy loam, clay or sand including lift up to 1.5 meter and lead up to 30 meter including filling, watering, ramming, of excavated earth into the trenches or up to the space and sides of the foundation trenches or into charge up to a distance of 30 meter from the foundation trenches.(b) Wet earth work in foundation. AS per ID SOR CH-VI/s.no. 1 b (i) Without water. |
| 2 | 2.25(a) Excavating, supplying, stacking and filling of local earth (including royalty)by mechanical transport upto a lead of 5km also including rammingand watering of the earth in layers not exceeding 20 cm in foundationtrenches, plinth, sides of foundation etc. complete for all lift. |
| 3 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONALanti-termite treatment (excluding the cost of chemical emulsion) : 2.35.1 Along external wall where the apron is not provided usingchemical emulsion @ 7.5 litres / sqm of the vertical surface ofthe substructure to a depth of 300 mm including excavationchannel along the wall & rodding etc. complete: 2.35.1.1 With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration |
| 4 | 2.35.3 Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: 2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinthlevel :1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 6 | Centering & Shuttering for R.C.C. work in slab of building work. |
| 7 | Cutting, bending, binding and placing in position of reinforcement including cost of binding wire but excluding cost of reinforcement steel. Thermo-Mechanically Treated bars of grade Fe-500D kg or more. |
| 8 | Providing and laying Cement concrete (1:1.5:3) with cement , coarse sand , and 10mm to 20mm stone grit including cost of all material, labour and T&P etc.complete. |
| 9 | Testing of building material (Cement, sand, brick,cube and aggregate) and submission of report from government institute. |
| 10 | Brick work in 1:4 cement mortar with cement , coarse sand , and M-150 bricks . including cost of all material, labour and T&P etc.complete. |
| 11 | Providing and laying Damp proof course 40mm thick in cc 1:2:4 with graded stone grit 10mm size including all material labour, and T&P etc |
| 12 | 8.2 Providing and fixing 18 mm thick gang saw cut, mirror polished,premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cementmortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement,mixed with matching pigment, epoxy touch ups, includingrubbing, curing,moulding and polishing of edges to give high gloss finish etc. completeat all levels.8.2.1 Raj Nagar Plain white marble/ Udaipur green marble/ Zebrablack marble 8.2.1.2 Area of slab over 0.50 sqm |
| 13 | Providing wood work in frames of doors, windows, clerestory windowsand other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).9.1.1 Second class teak wood |
| 14 | Providing and fixing panelled or panelled and glazed shutters for doors,windows and clerestory windows, fixing with butt hinges of requiredsize with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: Butt hinges and necessary screws shall be paid separately) 9.5.1 Second class teak wood 9.5.1.1 35 mm thick shutters |
| 15 | Painting two coat of superior quality of synthetic enamel paint approved make as per superior quality such as luxol highgloss, apcolite, superiac, dulux, on new wooden surface (excluding cost of primer) including material cost of all labout ,T&P etc. As per ID SOR Ch- XVII / S.No. 16 |
| 16 | Supply & Fixing pressed steel chaukhat made of M.S Sheet 18 gauge (1.25mm.) including iron hinges of 100 × 3 mm I.S.I. Mark, drilling holes of Ldrop tower bolt and 230 × 40 × 6 mm. flat iron hold fast including supply of all materials, labour, T&P, carriage up to site with one coat of red oxide primer.(C) Section 100 × 50 mm. for single rebutt door chaukhat. AS PER ID SOR CH- XV / S.No- 1 C |
| 17 | Providing & fixing 12mm. (1/2\\") thick and 100 mm (4\\") wide plyboard pelmets with 19 mm. dia. Stainless steel curtain rod and brackets, including fixing with 25 × 3mm. (P × 1/8\\") M.S. flat 10 cm. (4\\") long and plug etc. complete with painting, polishing or oiling as required excluding cost of all materials (as per NBO No 10.75) AS per ID SOR Ch- XIII (E)/ S.No. 21 |
| 18 | 10.25 Steel work welded in built up sections/ framed work, including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 10.25.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 19 | 9.48 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. 9.48.1 Fixed to steel windows by welding. |
| 20 | 10.28 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same withnecessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall beconsidered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 21 | Supplying & fabrication and fixing of Mild steel/iron work in grill, gates, railing, door, window frames including cutting, drilling, welding, riveting and fixing hinges where necessary with fixing in position including cost of all material, labour, T&P etc. required for proper completion of work with one coat of red oxide primer. As per ID SOR Ch- XV/ s.n-2 |
| 22 | 11.37 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 23 | 11.41 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointingwith grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. 11.41.2 Size of Tile 600x600 mm |
| 24 | 11.26 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 11.26.1 25 mm thick |
| 25 | 12.45 Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.45.1- 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) |
| 26 | 12.54 Providing and fixing Gl Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing ‘C’ wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with the help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of Gl steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with the help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with : 12.54.1 GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. |
| 27 | Cement Plaster in 1:4 Cement mortar 10 - 12 mm thickness including all labour T&P etc. with the lead of 60 m and lift of 3m . |
| 28 | 13.46 Finishing walls with Acrylic Smooth exterior paint of required shade : 13.46.1 New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 29 | 13.41 Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : 13.41.1 New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre |
| 30 | 13.26 Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 31 | 17.44 Providing and fixing single equal plain junction of required degree : 17.44.1 100x100x100 mm 17.44.1.1 Sand cast iron S&S as per IS - 1729 |
| 32 | 17.60 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :17.60.1 100 mm inlet and 100 mm outlet 17.60.1.1 Sand cast iron S&S as per IS: 3989 |
| 33 | 17.39 Providing and fixing plain bend of required degree. 17.39.1 100 mm dia 17.39.1.2 Sand cast iron S&S as per IS : 3989 |
| 34 | 17.58 Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter :17.58.1 100 mm |
| 35 | 17.58 Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter : 17.58.3 50 mm |
| 36 | 2.25(a) Excavating, supplying, stacking and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift. (Levelling with cleaning and groubing) |
| 37 | Footpath 125 mm GSB ,( 60MM INTERLOCKING TILES) WITH KERB STONE Edging ON PAVMENT AREA AS per DSR Plinth Area 5.2.4 |
| 38 | Storm water drainage line grid (on either side of building, front side and parking area) AS per DSR Plinth Area 5.5 |
| 39 | Storm water drainage line grid (on either side of building, front side and parking area) External sewer AS per DSR Plinth Area 5.3 |
| 40 | 19.15 Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design :19.15.1 With 20x20 mm square bar |
| 41 | 19.11 Constructing brick masonry circular manhole 1.22 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mmnominal size) finished with a floating coat of neat cement, all complete as per standard design :19.11.1 1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame tobe not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster atthe external surface shall be paid for separately) :19.11.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 42 | 23.1 Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level. 23.1.2 Rocky strata including Boulders 23.1.2.1 300 mm dia |
| 43 | 17.34 Providing and fixing toilet paper holder : 17.34.1 C.P. brass |
| 44 | 17.3 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 17.3.1 W.C. pan with ISI marked white solid plastic seat and lid. |
| 45 | 17.5 Providing and fixing white vitreous china flat back half stall urinal of size580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : 17.5.1 Single half stall urinal with 5 litre P.V.C. automatic flushing cistern |
| 46 | 17.25 Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : 17.25.1 Flat back wash basin of size 630x450 mm. |
| 47 | 17.28 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.17.28.1 Semi rigid pipe 17.28.1.1 32 mm dia. |
| 48 | 17.31 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 49 | 17.33 Providing and fixing 600x120x5 mm glass shelf with edges round off, supportedon anodised aluminium angle frame with C.P. brass brackets and guard railcomplete fixed with 40 mm long screws, rawl plugs etc., complete. |
| 50 | 17.73 Providing and fixing PTMT towel rail complete with brackets fixed to woodencleats with CP brass screws with concealed fittings arrangement of approvedquality and colour. 17.73.1 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms. |
| 51 | 17.71 Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. |
| 52 | 17.72 Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. |
| 53 | 17.35 Providing and fixing soil, waste and vent pipes :17.35.1.1 Sand cast iron S&S pipe as per IS: 1729 17.35.1 100 mm dia. |
| 54 | 17.37 Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : 17.37.1 For 100 mm dia pipe |
| 55 | 17.40 Providing and fixing heel rest sanitary bend 17.40.1.1 Sand cast iron S&S as per IS - 172917.40.1 100 mm dia |
| 56 | 17.44 Providing and fixing single equal plain junction of required degree :17.44.1.1 Sand cast iron S&S as per IS - 1729 17.44.1 100x100x100 mm |
| 57 | 17.43 Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 17.43.1.1 Sand cast iron S&S as per IS - 1729 17.43.1 100x100x100 mm |
| 58 | 17.42 Providing and fixing double equal plain junction of required degree.17.42.1.1 Sand cast iron S&S as per IS - 172917.42.1 100x100x100x100 mm |
| 59 | 17.46 Providing and fixing double unequal plain junction of required degree :17.46.1.1 Sand cast iron S&S as per IS - 172917.46.1 100x100x75x75 mm |
| 60 | 17.57 Providing and fixing collar :17.57.1.1 Sand cast iron S&S as per IS - 172917.57.1 100 mm |
| 61 | 17.53 Providing and fixing sand cast iron S&S off sets as per IS: 172917.53.1.2 With 100 mm dia pipe |
| 62 | 17.56 Providing and fixing terminal guard :17.56.1.1 Sand cast iron S&S as per IS - 172917.56.1 100 mm |
| 63 | 17.58 Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter :17.58.1 100 mm |
| 64 | 17.60 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :17.60.1.1 Sand cast iron S&S as per IS: 398917.60.1 100 mm inlet and 100 mm outlet |
| 65 | 17.61 Cutting chases in brick masonry walls for following diameter sand cast iron/ centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) :17.61.1 100 mm dia |
| 66 | 18.10 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.Internal work - Exposed on wall18.10.1 15 mm dia nominal bore |
| 67 | 18.10.2 20 mm dia nominal bore. |
| 68 | 18.10.3 25 mm dia nominal bore. |
| 69 | 18.10.5 40 mm dia nominal bore. |
| 70 | 18.13 Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :18.13.1 25 to 40 mm nominal bore |
| 71 | 18.15 Providing and fixing brass bib cock of approved quality :18.15.115 mm nominal bore |
| 72 | 18.16 Providing and fixing brass stop cock of approved quality :18.16.1 15 mm nominal bore |
| 73 | 18.17 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :18.17.1 25 mm nominal bore |
| 74 | 18.17.3 40 mm nominal bore. |
| 75 | 18.19 Providing and fixing gun metal non- return valve of approved quality (screwed end) : 18.19.1.2 Vertical18.19.1.2 Vertical 25 mm nominal bore |
| 76 | 18.19.3.2 Vertical 40 mm nominal bore. |
| 77 | 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 78 | 18.32 Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : |
| 79 | 18.40 Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :18.40.1 15 mm diameter pipe |
| 80 | 18.40.2 20 mm diameter pipe |
| 81 | 18.40.3 25 mm diameter pipe |
| 82 | 18.40.5 40 mm diameter pipe |
| 83 | 17.60 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :17.60.1.2 Sand Cast Iron S&S as per IS: 172917.60.1 100 mm inlet and 100 mm outlet |
| 84 | 17.61 Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) :17.61.1 100 mm dia.17.61.1 100 mm inlet and 100 mm outlet. |
| 85 | 19.1 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :19.1.2 150 mm diameter |
| 86 | 19.2 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes includingbed concrete as per standard design :19.2.2 150 mm diameter S.W. pipe |
| 87 | Wiring point for light with 1.5 sqm FR PVC insulated multistrand single core copper conductor cable in PVC conduit pipe partly concealed in wall and partly laid in slab along with reinforcement before concreting, complete with 1.5 sqmm.FR PVC insulated multi strand copper conductor cable as earth continuity wire witch etc. complete. Earth continuity wire and piano type switch etc. complete in all respects. 138C+187B |
| 88 | wiring point for 5 amp plug with 141 (B) but in PVC CONDUITE WIRE |
| 89 | Wiring point Exhaust fan with 1.5 sq.mm FRLSH PVC insulated multistrand single core copper conductor cable in PVCI conduit partly concealed in wall and partly laid in slab along with the reinforcement before concreting, complete with 14 SWG copper earth continuity wire, piano type switch & ceiling roase on 3 mm. thick bakelite sheet etc, complete in all respect including matching colour wash. (144B) PWD |
| 90 | Supply and fixing of power plug with 15A/250 volt flush type switch and 5 pin 15A/250V flush type universal socket in suitable M.S. box of 1.75mm x 100mm x 50mm size with phenolic laminated bakelite sheet cover 3mm thick fixed with brass machine screw and cup washer. 1139 PWD |
| 91 | Supply and wiringof submainwith two number 4 sq.mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm dia heavy guage rigidsteel conduit partly concealed in wall and partly laid in slab along with reinforcement before concreting, 20 mm dia (2mmthick) PVC conduit with one no. 2.5 sq. mm for PVC insulated multisrand copper conductor cable as earth wire drawn inside the conduit including matching colour wash etc. complete in all respect. PWD (221C) |
| 92 | Supply and wiring of submain in PVC insulated 1100 V grade single core Copper conductor cable in heavy gauge rigid PVC conduit partly laid in slab along with reinforcement before concreting with 25 mm dia heavy duty (2 mm thick) PVC conduit with one number 4 sq. mm. FRLSH PVC insulated multistrand copper conductor cable as earth continuity wire drawn in etc. complete in all respects. PWD (222C) |
| 93 | Supply and wiring submain with two number As in item no. 219(B) but in 25 mm dia heavy duty (2 mm thick) PVC conduit with 32 mm dia heavy duty (2 mm thick) PVC conduit with 83 one number 10 sq. mm. FRLSH PVC insulated multistrand copper conductor cable as earth continuity wire drawn in conduit. 219 (C) PWD |
| 94 | Supply and fixing of single light wall bracket on matching M.D.F.E.G. board base etc. complete all respect. 412 PWD |
| 95 | Supply and fixing of factory fabricated M.S. box in existing sunk of size 600mm x 480mm x 200 mm deep with godrej type almirah, cover with handle etc. fabricated from 18 SWG (1.25mm) M.S. sheet duly painted with red oxide primer followed by two coats of synthetic enamel paint complete with necessary conduit entry and D.P./T.P.N. fixing arrangements and provision for compartment for loose wires openable housing on the top and hold fast etc. including supply of all material, labour, T&P etc. required for proper completion of the work. 1147 PWD |
| 96 | Erection and testing of ceiling fan and regulator for room height up to 3.5 meters including supply of 3mm thick G.I Pipe 19 mm dia. Duly painted completed in all respect.1116 PWD |
| 97 | Supply and fixing of polished MDFEG/Teak ply cover for surface type B.D.B. above 4 ways complete with 50 mm hinges, aluminium kunda, chhapka and handle etc. complete in all respect. PWD 1127 |
| 98 | Supply and fixing 16 gauge M.S. drum duly painted including making hole in the wall for exhuast fan and finshing properly PWD 1122 complete in all respect. |
| 99 | Construction of recess pf 600mm x 480mm size of main boards, distribution boards of all sizes including cutting of brick work, providing lintel of suitable size and thickness, plastering etc. with supply of all material labour T&P required for proper completion of the work. PWD 1141 |
| 100 | Supply and fixing of electronic fan regulator (Modular) 120-280 V. ISI maked, on the existing switch board including making connections, required material, labour T&P etc. for proper completion of work to the satisfaction of engineer in charge of work. PWD 1203(C) |
| 101 | Supply & fixing surface/flush mounting 6ways VTPN adisribution board with additional metal without MCB complete in all respect, as directed at site by Engineer in PWD 1027 © |
| 102 | Supply and fixing of 240 volts 'L' series miniature circuit breaker in existing MCB, DB complete with connections as required. PWD 1002 |
| 103 | Supply and fixing of MCCB (16KA) Thernal Magnetic release. |
| 104 | S&F surface/flush mounting 12 ways SPN distribution board with additional metal door without MCB complete in all respect, as Direct by engineer in charge. |
| 105 | Supply and fixing of 36 watt indoor recess mounting LED Square Fitting for arnstrong ceiling having powder coated die cast aluminium housing with body with extended heat sink, diffuser of polycarbonate material and driver set complete in all respcet. |
| 106 | Supply and fixing of 36 watt indoor recess mounting LED Square Fitting for arnstrong ceiling having powder coated die cast aluminium housing with body with extended heat sink, diffuser of polycarbonate material and driver set complete in all respcet. Please Enable Macros to View BoQ information |
