|
| 1 | Dismantling of wrought iron or mild steel work of any description and in any position complete all as specified and directed. |
| 2 | S&F mild steel work Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or orged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 3 | Taking down cement plaster on brick or concrete surfaces of wall/ceiling and likes including racking out joints, hacking for keys scrubbing down with water etc any description including removal of rubbish outside MoD land, complete all as specified and directed. |
| 4 | M&L for rendering 15 mm thick in cm (1:4) on fair faces of concrete /stone masonry / brick surfaces and finished even and smooth without using extra cement and mixed with waterproofing compound @3% by weight of cement complete all as specified and directed |
| 5 | M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:3 as in ceiling complete all as specified and directed |
| 6 | M&L for rendering 15mm thick in CM 1:6. finished even & smooth without using extra cement to walls surfaces complete all as specified and directed. |
| 7 | M&L for preparation of newly plaster surfaces of walls and Distempering two or more coats with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification over a coat of 1.5mm (average) thick cement bases wall care putty complete all as specified and as directed by Engr-in-Charge. |
| 8 | M&L for preparation of newly plastered surfaces of ceilings and applying two coats of oil bound disember over a coat of chalk whiting primer complete all as specified and directed |
| 9 | M&L for preparation of newly plastered surfaces of wall and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & ungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and as directed by Engr-in-Charge. |
| 10 | Dismantling of galvalume aluminium zinc coating GI based plain or corrugated steel sheets of any thickness in roofing complete all as specified and directed. |
| 11 | S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge. |
| 12 | S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge. |
| 13 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for and disposing the debris out side defence land complete all as specified and directed. |
| 14 | M&L for 75mm thick PCC 1:3:6 type C2 using 40mm graded aggregate of as in sub base of flooring complete all as specified and directed. |
| 15 | M&L for PCC 1:5:10 type E2 (using 40 mm graded agg) as in sunken floor of toilet or mass concrete complete all as specified and as directed. |
| 16 | M&L for PCC 1:3:6 type C1 using 20mm graded aggregate of 75mm thick as in Plinth Protection finishing the surfaces even and smooth without using extra cement complete all as specified and directed. |
| 17 | Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing all the rubbish etc complete all as specified and directed. |
| 18 | Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed. |
| 19 | M&L for coloured non-skid Ceramic tiles of 7-8 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed 15 mm thick in cement mortar 1:4 complete all as specified and directed. |
| 20 | All as per item No. 19 above but as in skirting including rendering in cement mortar 1:3 as backing coat to receive skirting/dado complete all as specified and directed |
| 21 | M&L for Glazed Ceramic Coloured joint free tiles 350x250x 7mm/450x300x7 mm thick as in wall tiles, Dado/Skirting/Steps etc set and jointed in neat cement slury and pointed in coloured cement to match over 10mm thick backing Coat in CM 1:4.Complete all as specified and directed. |
| 22 | M&L for coloured non-skid ceramic tiles 7 to 8 mm thick area of each tile exc 0.11 sqm but not exc 0.18 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing including screed bed of 10 mm thick in CM 1:4 complete all as specified and directed. |
| 23 | M&L for 18-20mm thick sadarhalli stone flooring , steps, jambs, pillars window cills , cooking platform skirting in cement mortor 1:4 incuding pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15mm thick screed bed in CM 1:4 and rounding to edges complete all as specified and directed. |
| 24 | M/L for 18-20mm thick sadarhalli skirting in cement mortor 1:4 incuding pointing in white cement (1:2) using marbble dust with admixture of pigment to match with shade of granite including rendering 15mm thick in CM 1:4 and rounding to edges complete all as specified and directed. |
| 25 | M&L for 10mm thick Virified Ceramic tiles dark shade (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:4 complete all as specified and directed. |
| 26 | M&L for 12mm thick anti skid high matt finished endura tiles dark shade (square/ rectangular), area of each tiles exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:4 complete all as specified and directed. |
| 27 | Treatment of sunken floor slab compriases of the following specifications and all as specified :-(i) M&L for cleaning the sunken/lowered portion of RCC slab surface (including vertical total depth plus skirting height) of floors by wire brush, chisel out any mortar sticking to the surface and brooming completely. 40mm thick average PCC 1:2:4 type B0 using 12.5mm graded aggregate as in padding conc to achieve proper slope (ii) Rendering of uneven surfaces with 6mm thick CM 1:4 mixed with integral water proofing compound @ 3% BY WT OF CEMENT CONSUMED. Fill it with water and check dampness and seepage. Where dampness/seepage is noticed, nozzles shall be fixed and grouting to be carried out (WPC shall be measured and paid separately)(iii) All junctions points of side wall where CI/GI pipes are passing through shall be sealed with epoxy putty.(iv) After drying putty, wash the slab and sides of sunken portion with water and make it clear and clean.(v) M&L for applying two coats of polymer modified cementious water proof coating as per manufacturers instruction to bottom and vertical sides up to finished floor level +100mm height. The thickness of two layer shall be 1mm. When the second layer is still sticky, coarse sand spray shall be carried for the vertical and bottom surface of the sunken portion all as specified and directed. (This item shall be measured and paid separately).(vi) Plaster the bottom and sides up to bottom of the skirting with minimum 20mm thick CM 1:4 mixed with integral water proofing compound @3% wt of cment consumed as per manufacturer's specification including rounding of corners and junctions sloping towards spout. (WPC shall be measured & paid separately ) (vii) All pipes laid in sunken portion shall be covered with 50mm thick PCC 1:3:6 all round after painting with anticorrosive paint.Note :- Test the water proofed area (ponding test) by filling water for at least 72 hours and tested for leakage seepage and to the entire satisfaction of Engr-in-Charge. Cost of testing is included in the rates quoted above. |
| 28 | M&L for applying two coats of polymer modified cementious water proof coating as per manufacterors instruction to bottom and vertical sides up to finished floor level +100 mm height. The thickness of two layer shall be 1mm. When the second layer is still sticky, coarse sand spray shall be carried for the vertical and bottom surface of the sunken portion complete all as specified and directed. |
| 29 | Supply only Integral Water proofing compound complete all as specified and directed. |
| 30 | Taking up or down GI tubing and connections 15mm bore including cleaning or removal to store complete all as specified and directed. |
| 31 | S&F 15 mm dia UPVC pipes of pressure rating 10 Kgf/cm2 fixed to walls, ceiling or in floors etc complete all as specified and directed. |
| 32 | Taking up or down GI tubing and connections 20mm bore including cleaning or removal to store complete all as specified and directed. |
| 33 | S&F 20 mm dia UPVC pipes of pressure rating 10 Kgf/cm2 fixed to walls, ceiling or in floors etc etc complete all as specified and directed. |
| 34 | S&F in repairs stop valves/angle valve, cast copper alloy fancy type chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe of 15mm bore complete all as specified and directed |
| 35 | S&F in repairs stop valves, cast copper alloy fancy type chromium plated with long shank and cup (concealed type) for iron pipe of 20mm bore of complete all as specified and directed. |
| 36 | S&F in reapir 25 mm dia gun- metal globe or gate valves, with iron wheel head screwed both ends for iron pipe & fixed complete all as specified and directed. |
| 37 | S&F in repairs vitreous china floor mounted cascade type water closet white, with plastic water closet seat & back with flat bottom and cover including fixing bolts and necessary connection with existing pipes including attached vitreous tank of capacity 10 Ltrs etc complete all as specified and directed. |
| 38 | S&F in repairs vitreous china wash down water closet (pedestal pattern) white, including fixing bolts and necessary connection with existing pipes etc complete all as specified and directed. |
| 39 | S&F in repairs vitreous china wash down water closet (Squatt pattern) of size 580x440mm with integral foot rest white including necessary connection with existing pipes etc complete all as specified and directed. |
| 40 | S&F in repair for seat cover for pedestal pan with plastic water closet seat , white, closed pattern with flat bottom and cover amnd mild steel chromium plated or aluminised hinging device complete all as specified and directed. |
| 41 | S&F in repairs for 10 litre capacity PVC valveless syphonic action type flushing cistern high or low level (exclusive of brackets) white with inlet ball valve, float and handle inlcuidng brackets complete all as specified and directed. |
| 42 | S&F in repairs for providing 15 mm dia PVC connection of length 450mm long complete all as specified and directed. |
| 43 | S&F in repairs flush pipes PVC 32mm dia for low level flushing cisten to pedestal pan, including all joints, cones, India rubber (nozzles of W.C pans) complete all as specified and directed. |
| 44 | S&F in repairs CP health faucet along with 1 m long flexible tube and holding stand including all necessary fittings complete all as specified and as directed |
| 45 | S&F in Repair Bib Tap Sink Cock with flange 15 mm bore all as directed by the Engineer -in -charge. |
| 46 | S&F in repairs Wash hand basin vitreous china (flat back) size 550 x 400 mm including brackets waste brass chromium plated with long screwed shanks and fly nuts 32 mm size including bottle trap complete all as specified and directed. |
| 47 | S&F in repairs fancy type pillar taps cast copper alloy with capstan heads chromium plated screwed down high pressure with lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and 15 mm bore of pipe complete all as specified and directed. |
| 48 | S & F in repair PVC Waste pipe of size 32mm dia for WHB/Sink complete all as specified and directed. |
| 49 | S&F in repairs 32mm size waste fitting (coupling) brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed. |
| 50 | M&L 600x450 mm beveled edge looking mirror 5 mm thick selected quality glass mounted on 6 mm thick AC building board fixed to wall by wooden plug with chromium plated brass screw and cup washer fixed as in repair complete all as specified and directed. |
| 51 | S&F in repairs toilet paper holder brass chromium plated with flap complete all as specified and directed |
| 52 | S&F in repairs brass Chromium plated towel ring 30 cm round complete all as specified and directed. |
| 53 | S&F in repairs CP Soap dish 150mm, fixed to wall with chromium plated brass screws complete all as specified and as directed. |
| 54 | S&F in repairs Brass chromium plated tubular towel rail, 20mm dia ‘D’ type, 60CM long between flanges complete all as specified and as directed. |
| 55 | S&F in repairs Shower rose with brass chromium plated shower rose with or without swivel joints, 125mm size including fixing to steel pipe or union complete all as specified and directed. |
| 56 | S&F in repairs brass chromium plated mixer for mixing hot & cold water screwed down for 15mm dia iron pipe of complete all as specified and directed. |
| 57 | S&F in repairs for vitreous china urinals, bowl type (back or corner wall type) of size 465x355x265mm white with grating and union for discharge pipe complete including providing and fixing plugs bedding urinal against wall in cement mortar in 1:2 securing urinals to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cisterns with brackets, flush pipes, inlet, outlet etc complete all as specified and directed. |
| 58 | S&F in repair Push type taps for urinals, cast copper alloy with crutch or butterfly handle, screwed down, screwed for 15mm dia iron pipe or for brass ferrule and fixed in repairs complete all as specified. |
| 59 | S&F in repairs bib taps, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe 15mm bore complete all as specified and directed. |
| 60 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks etc complete all as specified and directed. |
| 61 | M&L for PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to wall 110mm bore etc complete all as specified and directed. |
| 62 | M&L for PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to wall 75mm bore etc complete all as specified and directed. |
| 63 | S&F 75mm dia PVC (SWR) bend complete all as specified and directed |
| 64 | S&F 100mm dia PVC (SWR) bend complete all as specified and directed |
| 65 | S&F 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed. |
| 66 | Dismantling of PVC water storage tank of capacity exceeding 250 litre but not exceeding 500 litre, including removal of rubbish outside MoD land, complete all as specified and directed. |
| 67 | S&F Rotational moulded PVC, tripple layered, water storage tanks of capacity 500 litre (cylindrical vertical with closed top), ISI Marked, hoisted and fixed in position, complete all as specified. |
| 68 | Dismantling of PVC/ RCC water storage tank of capacity exceeding 500 litre but not exceeding 1000 litre, including removal of rubbish outside MoD land, complete all as specified and directed. |
| 69 | S&F Rotational moulded PVC, tripple layered, water storage tanks of capacity 1000 litre (cylindrical vertical with closed top), ISI Marked, hoisted and fixed in position, incl 25mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed. |
| 70 | Cleaning and removing accumulated sludge/dirt scales from tank bottom, side and from mouths of circulating pipes of service PVC tank of capacity incl draining out water, exceeding 500 ltrs but not exceeding 1000 ltrs, located on roof of the building and disinfecting the tank using bleaching powder to make the tank bacteria free, writing by stencil date of cleaning of tank with white synthetic enamel paint on black ground \\" CLEANED ON ( DATE)\\" height of the words 100mm, complete all as specified and directed. |
| 71 | All as per item No 70 above but tank capacity not exc. 500 Ltrs complete all as specified and directed. |
| 72 | S&F in repairs 20 mm bore brass float valve, high pressure with polythene float & fly nut complete, screwed for GI pipe of following sizes including necessary GI fittings complete all as specified and directed. |
| 73 | Taking down of chowkat or frames with shutter of any discription (without taking off shutters from frames) n.exc 1.5 Sqm each and removing from site |
| 74 | All as per item No 73 above but exceeding 1.5 Sqm and not exceeding 4 Sqm each complete all as specified and directed. |
| 75 | Taking down only shutters of any description area n.exc 1.0 Sqm each and removing from site complete all as specified and directed. |
| 76 | All as per item No 75 above but area exc 1.0 Sqm and n.exc 2.00 sqm each complete all as specified and directed |
| 77 | S&F Pressed steel door frames ( 105mm x 60mm) with single rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed. |
| 78 | All as per item No 77 above but size of frame 125x60mm complete all as specified and directed |
| 79 | M&L for PCC 1:2:4 type B0 using 12.50mm graded aggregate as in filling of chowkats or steel frame etc incl necessary formwork complete all as specified and directed. |
| 80 | M&L for second class hardwood plain solid, straight chowkats and frames wrought framed rebatted on the solid, rounded or chamfered put together with glue, pinned at joints complete all as specified and directed. |
| 81 | S&F 30mm 2nd class hardwood Glazed and skeleton door shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain,chamfered or rounded. fitted with cut and mitred bead for securing glass,etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed. |
| 82 | S&F 30mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides kiln seasoned and chemically pressure reated complete all as specified and directed. |
| 83 | S&F 50mm x 47 mm size PVC solid door frame of size made out of 5mm plain Colour PVC sheet reinforced with MS square tube , supplying and fixing in opening as per specification and drawing shown in SSR 2004 Part II. complete all as specified and directed. |
| 84 | S&F 30mm thick factory made solid panel PVC door shutter (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain Colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck in side with solvent cement for stiles and plain Colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain Colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement supplying and fixing in the frame at site as per specification and drawing shown in SSR 2004 Part II. complete all as specified and directed. |
| 85 | S&F Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame., complete as specified by the manufacturer and as per directions of Engineer-in-charge. |
| 86 | S&F to existing door frames 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames, complete as specified by the manufacturer and as per directions of Engineer- in-charge. |
| 87 | S & F for powder coated aluminium frame for doors, windows, ventilators, powder coated of any color (tickness of powder coating not less than50 micron) with one or more rebates including cleat for fixing etc complete all as specified and directed |
| 88 | S&F Powder coated anodised aluminium door shutters, aluminium section weighing 0.55 kg/m (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and as directed. |
| 89 | S & F powder coated alluminium shutters for windows and ventilators side hung type without sash bars aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips rubber packing, anodised snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No) hinges type B-21 100 mm long (2 Nos) suitable handle (01 No) complete all as specified and directed. |
| 90 | S&F for 12 mm Particle board,medium density,flat pressed,single layer type or three layer type with BWR type adhesive,fixed with screws to frame work including necessary joining cleats,glazing clips, ruber neoprene packing,anodised aluminum snap beading, screws etc. complete all as specifiedNote : Price inclusive of Fixing the board into the aluminum frame and other fixing elements and fixing it into the required places as a partiton all as specfied and completed as directed by Engineer-in-charge |
| 91 | S&F Powder coated aluminium sliding window (three way) frame & shutter with glazed shutter and with wiremesh shutter /skeleton section with the following details :-(i) Aluminium frame section 116x36.50x1.80mm.(ii) Aluminium shutter glazed/skeleton section 50x20x1.50mm thick.(iii) Aluminium grill size 50mmx50mm and 4 to 5mm thick bars complete all as specified.(iv) Fixing arrangements legs in hold fast in walls incl PCC (1:3:6) making goog distributed surfaces complete in originally shape.(v) 4mm thick glass orinary quality and fixed with rubber gasket for with glazed shutter etc.(vi) Stainless steel wire mesh 0.36mm nominal dia avg aperature 1.14mm and fixed with rubber gasket for without glazed shutter etc.(vii) Aluminium disc /bow hanle and locking system complete |
| 92 | S&F Powder coated aluminium Ventilator (partially fixed glazing and Partially louvered glazing) with the following details :-(i) Aluminium frame section 45x25x1.80mm.(ii) Fixing arrangements legs in hold fast in walls incl PCC (1:3:6) making goog distributed surfaces complete in originally shape.(v) 4mm thick frosted glass orinary quality (partially fixed glazing and Partially louvered glazing) and fixed with rubber gasket for with glazed shutter etc. |
| 93 | M&L for 4mm thick figured glass, pin head type and glazing not exceeding 0.5 Sqm in each pane with and including beading & rubber packings fixed to aluminum/wooden shutters complete all as specified and directed. |
| 94 | S & F 4mm thick sheet glass .ordinary quality and glazing with oil putty in squares n exc 0.5 Sqm in Sqm each pane. |
| 95 | S & F in repairs 4mm thick sheet glass .ordinary quality and glazing with oil putty in squares n exc 0.5 Sqm in Sqm each pane. |
| 96 | S&F in repairs 3 mm Sheet plain glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane Complete all as specified and as directed. |
| 97 | S&F Aluminum Alloy wire cloth, 0.45mm nominal dia of wire & average width of aperture 1.40mm and fixed with wire staples complete all as specified and directed |
| 98 | S & F in repairs Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 99 | S&F in repairs 19mm thick MDF Board both side finished as in wardrobe or kitchen cabinets, cupboard etc no of compartments & Drawers including frame and fixing to any type of frame/wall complete all as specified and directed |
| 100 | S&F 100 mm Butt hinges, Heavy weight, cold rolled, mild steel complete all as specified and directed. |
| 101 | S&F 75 mm Butt hinges, medium weight, cold rolled, mild steel complete all as specified and Each directed. |
| 102 | S&F 150 mm extruded anodoised aluminium alloy handles fabricated type complete all as specified and directed. |
| 103 | S&F in repairs 150mm extruded anodised aluminium alloy handles, fabricated type complete all as specified and directed. |
| 104 | S&F aluminium anodised, barrel tower bolts of extruded section with length of bolt 150 mm and fixed complete all as specified and directed |
| 105 | S&F 125 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed. |
| 106 | S&F aluminium anodised, barrel tower bolts of extruded section with length of bolt 100mm and fixed complete all as specified and directed |
| 107 | S&F 300mm length, Aluminium alloy anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed |
| 108 | S&F for 2 lever brass Mortice lock, vertical type, 100mm size complete all as specified and directed |
| 109 | M&L for Magnetic / Ball catches with 8 mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and as directed. |
| 110 | S&F in repair Aluminium (extruded section body) Door Closer Hydrulically regulated designation No-1 universal type, suitable for door shutters up to 700mm in width and of weight not more than 35 kg and fixed complete all as specified and directed. |
| 111 | S&F in repairs Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and as directed. |
| 112 | S&F Continuous (piano) hinges, mild steel bright finish or electrogalvanised of width of flaps 30 mm (when open) complete all as specified and directed. |
| 113 | S&F 300mm MS ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and directed. |
| 114 | Dismantling of wall and ceiling boards (fibre, pulp, insulation) or insulation boards /slab /blankets of any description and thickness including frame/grid of any description complete all as specified and directed |
| 115 | M&L for Anodised Aluminium snap grid (minimum 15 microns anodisation) of size 605 x 605 mm with anodized aluminum angle of size 40mm x 25mm x 2mm thick weighing 0.36 Kg per running meter and anodized aluminum main and cross T of size 36.50 x 23.50 x 1.50 mm thick weighing 0.254 Kg per running meter and 23.50 x 23.50 x 1.50 mm thick weighing 0.202 Kg per running meter respectively for false ceiling complete all as specified and directed. |
| 116 | S&F hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long suitable for size of snap grid 605 x 605 mm complete all as specified and directed |
| 117 | M&L for 6mm calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600mm grid (Frame work for ceiling shall be measured and paid separately) in ceiling fixed with screws on snap grid complete all as per manufacturer instructions as directed. |
| 118 | Demolition of brick work, precast concrete block walling or stone boulder masonry, built in cement mortar including all quoins, arches, pillars, etc complete all as specified and directed. |
| 119 | M&L for precast cement concrete block (Type C1 1:3:6 20 mm graded aggregate) masonry with solid block, exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed. |
| 120 | M&L for precast cement concrete block (Type C1 1:3:6 20 mm graded aggregate) masonry with solid block, not exc 10 cm in width and setting in cement mortar 1:4 complete all as specified and directed. |
| 121 | M&L for applying two coats of synthetic enamel paint over a coat of pink primer including preparation of new wooden surfaces of any description exc 10 cm in width or girth complete all as specified and directed. |
| 122 | M&L for applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer including preparation of new steel surfaces of any description exc 10 cm in width or girth complete all as specified and directed. |
| 123 | S&F in Repair 25mm dia aluminium anodised Powder coated Curtain Rod of approved quality complete all as specified and directed. |
| 124 | S&F in repair decorative type curtain rod brackets with side doms suitable for 25mm dia curtain rods complete all as specified and directed. |
| 125 | S&F Black/golden colour solar control film 25 micron reflective type sticked to glass panes as per instruction of manufacturer complete all as specified and directed. |
| 126 | S&F in replacement venetian blinds, vertical type, 100 mm slot width of approved fabric and powder coated aluminium top railsetc complete all as specified, including dismantlilng old damaged one complete all as specified and as directed. Note:The colour,design and shade shall be as approved by GE. |
| 127 | S&F in replacement Roller blinds, horizontal type, 100 mm slot width of approved fabric and powder coated aluminium top rails etc including dismantlilng old damaged one complete all as specified and as directed. Note:The colour,design and shade shall be as approved by GE. |
| 128 | Taking down steel rolling shutters of any area and any description, top cover with all parts such as shaft, spring, ball bearing, drum, CI pulley complete from brackets, channel etc greasing and replacing worn out parts as directed by Engineer-in-Charge and re-fixing the same after realigning the shaft/guide channel, welding drum cage, servicing the components for smooth functioning including one coat of Synthetic enamel paint complete all as specified and directed by the Engineer-In-Charge.Note: Parts replaced will be measured and paid seperately |
| 129 | Supply only Hood cover of MS sheet 0.50mm min thickness including painting two coats with synthetic enamel paint over a coat of red oxide primer complete all as specified and directed Note : Colour to match with existing rolling shutter paint |
| 130 | Supply only safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed. |
| 131 | Supply only ball bearing for rolling shutter as per existing make and size complete all as specified and directed. |
| 132 | Supply only anchoring rod for rolling shutter complete all as specified and directed. |
| 133 | Supply only channels / guide rails as per existing shape and size complete all as specified and directed. |
| 134 | Supply only 1.25mm thick laths for rolling shutter including one shop coat of red oxide primer & painting to match the existing one complete all as specified and directed. |
| 135 | S&F in repairs Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded, complete all as specified and directed. |
| 136 | Servicing of aluminium sliding / Side hung window / door shutters of any type including renewal of worn out parts like rubber beading, rollers, handles, hinges, locks, etc and including necessary scafolding work if required complete all as specified and as directed. |
| 137 | Servicing of Steel windows such as easing /adjusting in existing frame including welding if required complete all as specified and as directed. |
| 138 | Taking down collapsible steel gates/shutters consisting of channel, pickers, pivoted flat bars, top and bottom runners for servicing and checking its function including fixing only new wheels, top and bottom channels, cleaning and greasing of wheels and channels etc., complete and fixing in its original position complete area exc 4.00 Sqm and n.exc 10 Sqm each, complete all as specified and directed. Please Enable Macros to View BoQ information |
