|
| 1 | Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed. |
| 2 | Demolition of brick work or stone/boulders masonary, built in cement mortor including all quoins, arches pillars, etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed. |
| 3 | Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc, laid, bedded, jointed and pointed in any mortar complete all as specified and directed by Engineer-in-charge. |
| 4 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off premises complete all as specified and directed. |
| 5 | Taking down chowkhats with shutter (without taking off shutters from the frame) area not exc. 1.50 Sqm each complete all as specified and directed. |
| 6 | Taking down chowkhats with shutter (without taking off shutters from the frame) area exc. 1.50 Sqm but n.exc 4.00 sqm each complete all as specified and directed. |
| 7 | Taking down shutters of any description exc 1 Sqm and not exc. 2 Sqm each complete all as specified and as directed by Engineer-in-charge. |
| 8 | Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thick above or below ground level complete all as specified and directed. |
| 9 | Dismantling of wall and ceiling boards of any type and any thickness including cover fillets complete all as specified and directed. |
| 10 | M&L for Brick work with sub class ‘B’ old size burnt bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed by Engineer-in-charge. |
| 11 | All as per Srl item No 10.00 here-in-before but except brick.Note : Old serviceable brick retrieved from serial item No 2.00 of BOQ here-in-before shall be used under this item. |
| 12 | M&L for in repair to aluminium door/window of any size/any description , taking off from present position and refixing in the same position after tightening , easing/change the section as required , including fitting the rubber packing aluminium snap beading resetting floor/hydraulic door closer/spring etc complete all as specified and directed. |
| 13 | S&F Pressed steel frame for doors of size 105 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed. |
| 14 | S&F Pressed steel frame for doors of size 125 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed. |
| 15 | M&L for cement concrete type C-1, (1:3:6) using 20mm graded aggregate as in bed block or filling of chowkhats including necessary form work complete all as specified and directed. |
| 16 | M&L 35mm thick factory made glazed and skeleton shutters of 2nd class HW with partially panel shutter open rebated and prepared to receive glass / gauze etc edges or framing plain chamfered or rounded fitted with cut or mitred beads for securing glass etc as specified in SSR Part-1 section 8.24 (a) complete all as specified and directed. |
| 17 | S&F 35mm thick plain framed panelled door shutter, factory made (any number of panels) of 2nd class hard wood with lock rail and panels of 9mm thick BWP commercial ply or 12mm thick veneered particle board with commercial veneering on both faces including 2nd class hard wood kail beading 20mm wide tapering from 10mm to 5 mm on one side of shutter & fitted to chowkhats. The size of rail and style shall be as per IS –1003 (Part-I) (wood shall be kiln seasoned and chemically pressure treated) complete all as specified and directed. |
| 18 | M&L for 35 mm thick flush shutter with solid core construction with block board core and plywood face panels , commercial type on both sides members of shutters, covered decorative on both face veneer with liping/frame to match as specified in SSR Part I, section 8, clause 8.24 (a); supplied & fitted to Chowkats complete all as specified and directed by Eng-in-charge. |
| 19 | S&F factory made solid PVC door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified & shown in relevant drawing of item No. 08095 in MES Schedule (Part-II) and directed by Engineer-in-Charge. |
| 20 | S&F 30mm thick factory made solid PVC moulded door shutter with particle board core with 5mm thick PVC moulded sheet on the front face and 5 mm thick PVC plain colour sheet on back face complete all as specified and directed by Eng-in-charge. |
| 21 | S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note : (i) MS hold fast/ lugs or SS dash fasteners shall be paid for separately). (ii) For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 22 | S&F Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-in- Charge. Note: Stainless steel butt hinges and necessary SS screws shall be paid separately. |
| 23 | Providing and fixing factory made UPVC white colour sliding window three track made of extruded profile with wall thickness of 2.3mm (+/- 0.2mm). Window profile with hollow section with multi chamber, frame (88mm x 52mm), sliding sash (42mm x 67mm), sliding mesh sash (42mm x 57mm) sliding interlock (one vertical leength in each shutters)(45.5mm x 28mm), Glazing bead (24.5mm x 16mm) wil be mitered cut and fusion welded at all corners, inluding drilling of holes for fixing hardware and drainage of water etc, making arrangement for fiixing hardware. Cont/- |
| 24 | Cont/-EPDM gasket, 1.2 +/- 0.2mm thick galvanised steel frame (30mm x 18mm) 2 Nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100 long fasteners. Hardware: (Touch lock of zinc alloyed (white powder coated), steel roller system, stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm and required acecessories.) (Note: The unit rate quoted by contractor includes cost of 5.00 mm thick sheet glass, selected quality and all other connected accessories. Net openeing will be measured for payment purpose.) |
| 25 | Providing and fixing factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Cont/- |
| 26 | Cont/-Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) [and 5mm thick frosted glazing with selected quality glass. (Note: The unit rate quoted by contractor includes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) |
| 27 | S&F in repair lever door handle for UPVC doors and windows complete all as specified and directed. |
| 28 | S&F in repair 3D hinges for UPVC doors and windows complete all as specified and directed. |
| 29 | S&F powder coated (minimum thickness of powder coating 50 micron) Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. |
| 30 | S&F powder coated Anodised aluminium window and ventilator shutters side hung type without sash, aluminium sections weighing 0.55 kg/ m including necessary joining cleats, glazing clips rubber packing, anodised aluminium snap beading screws Anodise aluminium fitting such as peg stays 150 mm long (1 No ), including pag stay and hinges type B-21 100 mm long (2 No) and suitable handle (1 No) complete all as specified and directed. |
| 31 | S&F powder coated Anodised aluminium door section, aluminium sections weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading screws Anodise aluminium fitting such as including hinges 100 mm long (2 no) and suitable handle(2 No) complete all as specified and directed. |
| 32 | M&L for aluminium grill mesh made out of 6mm dia having girth not exc 25mm both ways fixed with aluminium cleat to window frame complete all as specified and directed by Engineer-in-Charge. |
| 33 | S&F powder coated aluminum partition using 95.6mmx 44.8mm x 1.00-1.2mm frame work with 12mm thick exterior grade veneered particle board with decorative veneers on both face/5.5mm thick frosted glass including aluminum beading for fixing board each panel n.exc 1.2 Sqm complete all as specified and directed by Eng-in-charge. |
| 34 | S&F 5.5 mm thick plain glass, ordinary quality and glazing with oil putty in square n exc 0.5 sqm in each pane. |
| 35 | S&F Sheet glass 4 mm thick in glazing to aluminium door, window & partition including pad, gasket complete all as specified and directed. |
| 36 | S & F 5mm thick coloured ACP (Aluminium composit Pannel) sheet using aluminium partition including joining cleats for fixing etc.(colour of sheet approved by GE). |
| 37 | S&F Mortice latch with two levers (vertical type), aluminium, anodised body and fixed complete all as specified and directed. |
| 38 | S&F 150 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed by Engineer-in-charge. |
| 39 | S&F 200 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed by Engineer-in-charge. |
| 40 | S&F in repairs 200 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed by Engineer-in-charge. |
| 41 | S&F 300 mm aluminium alloy, anodised sliding door bolts with hasp, staple and fixing clips of sheet, cast or extructed section and fixing bollts and sliding bolts of extruded section or cast aluminium ally and fixed complete all as specified and directed. |
| 42 | S&F in repair 300 mm aluminium alloy, anodised sliding door bolts with hasp, staple and fixing clips of sheet, cast or extructed section and fixing bollts and sliding bolts of extruded section or cast aluminium ally and fixed complete all as specified and directed. |
| 43 | S&F Aluminium handles cast type anodised of size 150mm size, complete all as specified and directed. |
| 44 | S&F 100mm long stainless steel Butt hinges fixed complete all as specified and directed. |
| 45 | S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring overall length of cover plate 140mm (ISI marked) complete all as specified and directed by Engineer-in-Charge. |
| 46 | S&F for double action floor spring hydraulically regululated made up of minimum 1.25mm thick aluminum sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed by Eng-in-charge. |
| 47 | S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed by Engineer-in-Charge. |
| 48 | S&F in repairs stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples complete all as specified and directed by Engineer-in-Charge. |
| 49 | Hacking out old broken glass any thickness, size, quality or description from wooden / metal frame and punching or drilling out old glazing pins/spring clips complete all as specified and directed by Engineer-in-charge. |
| 50 | M&L 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, complete all as specified and as directed. |
| 51 | M&L 3mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane complete all as specified and directed by Engineer-in-charge. |
| 52 | M&L for glazed ceramic tiles (coloured) 450mm x 300mm x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick rendering in cement & sand mortar (1:4) including necesary cutting as per site requirment complete all as specified and directed by Engineer-in-charge. |
| 53 | M&L Non skid coloured ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but n.exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match with and including 15mm thick screed bed in cement mortar (1:6) for laying floor finishes complete all as specified and as directed. |
| 54 | M&L for vitrified ceramic tiles light shade 8-9mm thick (square/ rectangular) polished area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick cement screed bed in CM (1:4) complete all as specified and directed. |
| 55 | All as per item No 52.00 (here-in-before) above but as in skirting over 10mm thick backing coat in CM (1:3) complete all as specified and directed. |
| 56 | M&L for vitrified ceramic coloured tiles in vertical surfaces 600 x 1200 x 10mm thick and jointed in neat cement slurry and pointed in white or coloured cement to match including tile adhesive for skirting/dado finishes complete all as specified and directed. |
| 57 | M&L for vitrified non skid ceramic tiles light shade 10mm thick (square/ rectangular) polished area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick cement screed bed in CM (1:4) complete all as specified and directed. |
| 58 | M&L Plain cement concrete type B0 (1:2:4), using 12.5 mm graded crushed stone aggregate, 25 mm thick , as as in floor and finished even and smooth using extra cement laid in alternate bay and joints filled with bituminous compound grade 'A' complete all as specified and directed. |
| 59 | M&L for machine cut Kota stone slab flooring 20 to 25mm thick (minimum size 550mm x 550mm or size as directed) laid over & including screed bed or bedding layer of 20mm thick in CM (1:6) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-charge. |
| 60 | M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) for Shelves (veneering to wall) including 15mm thick plaster in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed. |
| 61 | M&L for 75 mm thick PCC (1:3:6) type C-2 using 40 mm graded crushed stone aggregate as in plinth protection, finished fair and even complete all as specified and directed by Engineer-in-charge.Note :- Plinth protection shall be laid to slope (1 in 30) in bays not exceeding 3 metre in length and joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with sealing compound grade B. Cost of ceiling compund is included in the unit rate of this item complete all as spcified and directed. |
| 62 | M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and directed. |
| 63 | M&L for rendering 15 mm thick in CM 1:4 including water proofing compound on fair face of brick or concrete surface,finished even and smooth without using extra cement complete for heigh upto G+2 story building complete all as specified and directed. |
| 64 | M&L for rendering 5mm thick in CM (1:4) as on ceiling complete all as specified and directed. |
| 65 | Supply only Liquid water proofing compound of approved complete all as specified and directed. |
| 66 | M&L for washed stone grit plaster on exterior walls in two layers the base plaster shall be 15mm thick in two layers. First layer 10mm thick in CM (1:6) & top layer 5mm thick in CM (1:4) mixed with approved water proofing compound @ 3% & shall be sufficiently rough and combed be wire brush or nail comb, feed from all dust, dirt, grease, oil etc for proper bonding. The base plaster shall be cured for 3 to 4 days before applying the grit wash plaster. A homogeneous mix of white cement, coarse sand and 10mm nominal size sone chippings of approved colour in proportion 1:1/2:2 be prepared by adding water proofing compound @ 2% by weight of cement and be mixed homogenously and then mix be applied on a prepared base Cont/- |
| 67 | Cont/-surface with a float applying gentle pressure in panels with groove all around as per approved pattern including beading, White cement slurry shall be applied @ 2Kg/sqm on base coat before applying a stone grit wash plaster. After the initial setting of about 1 to 2 hours the surface of stone grit plaster surface be scrubbed and washed out gently with a nylon brush and water. The cement on the surface of stone chips be washed away exposing the aggregates and plastered surface shall be cured for 14 days including necessary steel scaffolding work, complete all as specified and directed. |
| 68 | M&L for applying a coat of two component elastomeric acrylic polymer modified cementitious water proofing coating, having properties of 80 % elongation as per ASTM D412, resisting 5 bars hyrostatic pressure as per DIN 1048, reduction to rapid chloride shall be 70 as per DIN 1048, crack bridging upto 1.2mm as per ASTM 4548.5. The mixing ratio of the coating shall be 2 parts of powder & 1 part of liquid without any water addition in the mixing, etc., complete as per manufacturers specifications and sprinkle sand at 10-15 gram per sqft for better grip with plaster complete all as specified and directed. |
| 69 | Taking up or down 15mm dia, steel tubing & connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge. |
| 70 | Taking up or down 20mm dia, steel tubing & connections including cleaning for refixing or removal to store complete all as specified and directed by Engineer-in-Charge. |
| 71 | S&F 15 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge |
| 72 | S&F 20 mm dia steel water tubing, galvanized, medium grade, with all fittings, fixed to walls and ceiling or in floor complete all as specified and directed by Engineer-in-Charge. |
| 73 | Disconnecting existing tanks of capacity exc 500 ltr & not exc 1000 ltr, setting aside (or lowering if required) for repairs and cleaning & removing all scale and dirt etc, from tank and from mouths of circulating pipes and hoisting and re-fixing in same or other position complete all as specified and as directed by Engineer-in-charge. |
| 74 | S &F for rotational moulded polythelene water tanks triple layer white colour (cylindrical vertical with closed top) hoisted and fixed in position for 750 ltr. storage capacity including disconnecting and taking down old unserviceable tanks and ball valve complete all as specified and directed. |
| 75 | S&F 20mm dia PTMT ball PVC valve, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed by Eng-in-charge. |
| 76 | S&F in repair 20mm dia ball brass valve, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed by Eng-in-charge. |
| 77 | S&F in repair 20mm Gate valves, high pressure, with polytheene float and flynut complete, screwed for iron pipe orr brass ferrule and fixed. |
| 78 | S&F in reapir PVC water tank cover for any capacity of PVC water tank fixed with suitable bolt & nuts complee as directed. |
| 79 | S&F PVC (SWR) 75 mm bore pipes single socketed in any length with rubber ring joints laid in trenches or fixed to wall complete including taking down old unserviceable PVC pipe with fittings complete all as specified and directed. |
| 80 | S&F PVC (SWR) 110 mm bore pipes single socketed in any length with rubber ring joints laid in trenches or fixed to wall complete including taking down old unserviceable PVC pipe with fittings complete all as specified and directed. |
| 81 | S&F PVC (SWR) 75mm bore bends any radius complete all as specified and directed. |
| 82 | S&F PVC (SWR) 110mm bore bends any radius complete all as specified and directed. |
| 83 | S&F 100mm CI pipes soil, waste and vent pipe in any length with or without ears, with cement joints fixed to wall including taking down old unserviceable CI pipe and fittings complete all as specified and directed. |
| 84 | S&F 100mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified and as directed by Engineer-in-charge. |
| 85 | S&F 75mm CI pipes soil, waste and vent pipe in any length with or without ears, with cement joints fixed to wall including taking down old unserviceable CI pipe and fittings complete all as specified and directed. |
| 86 | S&F 75mm bore cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified and as directed by Engineer-in-charge. |
| 87 | S&F in repairs 32mm bore CP waste coupling fittings for sinks, basins with long shanks and fly nuts, flange and bedded in red cement and fixed complete all as specified and directed by Eng-in-charge. |
| 88 | S&F in repairs PVC waste pipe 32mm dia of length 0.8mm to 0.9mm fixed complete all as specified and directed. |
| 89 | S&F in repair chromium plated shower rose with or without swivel joints including fixing to steel pipe of 100 mm size complete all as specified and directed by Eng-in-charge. |
| 90 | S&F in repair CP Jet spray butter fly design fixed on EWC with stanless screw as approve complete all as specified and directed by Eng-in-charge. |
| 91 | S&F in repair 450mm long PVC connection suitable for 15 mm bore with PTMT nuts on both sides complete all as specified and directed by Engineer-in-charge. |
| 92 | S&F in repair 15mm bore CP angle valve, fancy type, cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed by Engineer-in-charge. |
| 93 | S & F in repair for 15mm bib tap standard of PTMT any colour screwed for iron pipe and fixed complete all as specified and directed by Eng-in-charge. |
| 94 | S & F in repair for 15mm angle cock standard of PTMT any colour screwed for iron pipe and fixed complete all as specified and directed by Eng-in-charge. |
| 95 | S & F in repair for 15mm Pillar tap fancy type standard of PTMT any colour screwed for iron pipe and fixed complete all as specified and directed by Eng-in-charge. |
| 96 | S&F in repairs 15mm bore brass chromium plated WHB mixer for mixing hot & cold water screwed down for iron pipe of 15mm bore complete all as specified and directed by Engineer-in-charge. |
| 97 | S&F in repair 15 mm bore bib tap, cast copper alloy, chromium plated, long body, fancy type screwed down and screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-charge. |
| 98 | S&F in repair vitreous china squatting pan Orissa pattern, white of size 580x440mm with integral foot rests (excluding flushing cistern and flush pipe) including cast iron 'P' or 'S' trap, PCC filling and connection to trap and flushing pipe, antisyphonage pipe etc complete all as specified and directed by Engineer-in-charge. |
| 99 | S&F in repairs vitreous china wash down water closet pan (Pedestal pattern), white including connection to drain (or outgoing pipe) and to flushing pipe, anti-sypohonage pipe etc. & with plastic WC seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device and jet spray complete all as specified & as directed by Engineer-in-charge. |
| 100 | S&F in repairs PVC EWC seat cover of any type, white colour for pedestal pan complete all as specified and directed by Eng-in-charge. |
| 101 | S&F in repair 10 litre capacity PVC valveless symphonic action type low level flushing cistern (ISI marked) including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified and directed by Engineer-in-charge. |
| 102 | S&F in repairs, vitreous China wash hand basin, white, flat back size 550 x 400mm including 15mm dia, 450 mm long HDPE PVC connection, 750 mm long 32mm bore HDPE waste down pipe including CI brackets complete all as specified and directed. |
| 103 | S&F in repair pillar taps (fancy type), of 15 mm dia, cast copper alloy, with capstan heads, with chromium plated, screwed down high pressure with or without lettered 'hot' or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed. |
| 104 | S&F in repair pillar taps (fancy type) swan neck with long shank, of 15 mm dia, cast copper alloy, with capstan heads, with chromium plated, screwed down high pressure with or without lettered 'hot' or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed. |
| 105 | S&F pillar taps (fancy type), of 15 mm dia, cast copper alloy, with capstan heads, with chromium plated, screwed down high pressure with or without lettered 'hot' or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed. |
| 106 | M&L preparation new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc chrome primer complete all as specified and directed by Engineer-in-Charge. |
| 107 | M&L for preparation of new wooden or wood based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge. |
| 108 | S&F Factory made box type steel windows with hung shutters both glazed and guaged shutter frame 60x25 mm ERW hollow 'P' section with wall thickness not less than 1mm fixed to pressed steel frame 120mm x 70 mm x 1.6mm thick including fixing glazed portion, iron grills 8mm square MS bar hunges with steel handle and fitting, lugs etc, including one shop coat of primer complete all as specified and directed. |
| 109 | M&L for preparation of new plastered surface of wall and applying two coats of acrylic distemper over a coat of primer complete all as specified and directed. |
| 110 | M&L for preparartion of new plastered surfaces of walls and applying two coats cement base paint on walls complete all as specified and directed. |
| 111 | M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed. |
| 112 | M&L for preparation of old distempered surfaces of walls by washing, rubbing down and stopping of distempered and painted surfaces and treating oil and greasy spots and applying one coat of oil bound distemper oil emulsion white or tinted complete all as specified and directed. |
| 113 | M&L for preparation of old decorated, plastered or pointed surfaces of ceiling by brooming down or steel wire brushing,scrapping down smoke soot moulds, moss and efflorescent, salts and treating oil & greasy spots etc and applying one coat of white wash complete all as specified & directed by Engineer-in-Charge. |
| 114 | M&L for preparation of old plaster surfaces of walls and applying one coat of cement based paint on walls for height upto G+2 story bldg complete all as specified and directed. |
| 115 | M&L for complete removal and preparation of old painted surfaces of wall and applying two coat of exterior emulsion paint for height upto G+2 story bldg complete all as specified and directed. |
| 116 | S&F in repairs curtain rod, stainless steel of 25mm dia with fixing brackets stop rollers etc fix complete all as specified and directed. |
| 117 | S&F venetian blinds for window UV protection, waterproof, corded roll up and down blinds and blinds including roller shade contains metal bracket, screw etc complete all as specified and directed by Engineer-in-charge. |
| 118 | S&F solar control film 25 micron reflective type ( gareware sun control or equivalent ) sticked to glass panel as per instructions of manufacturers complete all as specified and directed. |
| 119 | S&F UPVC door lock set alongwith handle & keys of any shade complete all as specified and directed. |
| 120 | S&F in repairs mild steel Door seal for doors upto 1000mm long and thickness not less than 1mm complete all as specified and directed. |
| 121 | S&F in repair CP Health faucet with stand fixed on wall in CP hose pipe 1 mtr length and stainless steel screw as approve complete all as specified and directed by Eng-in-charge. |
| 122 | S&F in repairs peg set of five of stainless steel bright finished, fixed complete all as specified and directed by Eng-in-charge. |
| 123 | M&L for bands, straps, supports or stays for rainwater, Ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and lintle hanges, large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters ; knee piece inserts; two way and three ways straps , plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed. |
| 124 | S&F in repair brass chromium plated tubular towel rail 20mm dia; 'D' type, 600mm long between flanges fixed to plug with chromium plated brass screws including wooden or plastic cleat complete all as specified and directed by Engineer-in-Charge. |
| 125 | S&F in repair 600mm x 450mm beveled edge looking mirror of selected quality glass not less than 5.5mm thick, mounted on 6mm thick commercial plywood including PVC moulded framing and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed by Engineer-in-charge. |
| 126 | S&F in repair PVC Syphon kit assembly in existing flush tank complete all as specified and directed. |
| 127 | S&F in repair PVC mirror cabinet size 350X450mm of standard size fixed to wall with PVC sleeves and steel screws complete all as specified and directed. |
| 128 | S&F in repair Glass shelf 450mm long x 100 mm wide including brackets fixed to wall with sleeves and screws complete all as specified and directed. |
| 129 | S&F in repair corner glass shelf of size 300X300 mm including brackets fixed to wall with pvc sleeves and stainless steel screw complete all as specified and directed. |
| 130 | S&F in repairs vitreous china urinal Half stall type, white incl CP spreader screwed for iron pipe and fixed complete including providing and fixing plugs with and including 60mm long brass screws, pointed around urinal back in cement, fixing discharge pipr, flush pipe, grating and union for discharge complete all as specified and directed by Eng-in-charge. |
| 131 | S&F in repair stainless steel grating 100mm bore size fixed with white cement complete all as specified and directed by Eng-in-charge. |
| 132 | S & F 605X605 mm size of grid GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended form soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section ( not exc 1.2 m length ) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre including Hangers 6 mm dia. GI (up to 1200 mm length ) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40X 3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia. 40 mm long etc complete all as spd and as directed. Incl providing and fixing coloured designer board 4 mm thick in ceiling fixed with screw as per manufacturer's instructions complete all as specified and directed by Eng-in-charge. |
| 133 | S&F hollow corrugated shape PVC wall lining consisting of 5mm thick decorative colour PVC sheet, heavy duty as per sample approved by GE, inclusive of solvent cement and fixing and incl beading at sides on PVC frame as per specifications all as specifed complete all as specified and directed. |
| 134 | S& F 18 mm thick Hybrid Water Proofing Board in cupboard shutter with decorative on one side & other side balancing white fixed by drilling screws complete all as specified and directed by Engr-in-charge. |
| 135 | S&F 100mm long stainless steel handles, oval type complete all as specified and directed. |
| 136 | S & F Continuous (piano) hinges,mild steel, bright finish or electrogalvanised 30 mm Width of flaps (when open) in mm all as specified all as directed. |
| 137 | S&F Magnetic catcher fixed in with nut,screw washer complete all as specified and directed by Eng-in Charge. |
| 138 | S&F 12mm thick toughened glass door with film of size exceeding 1.5 Sqm but not exceeding 3.00 Sqm including steel connectors, top and bottom pivots, stoppers, other fixtures required and all type of locking arrangement & brass handles fancy type 300mm long hole to hole on both side complete including taking down old unserviceable glass door complete all as specified and directed.Note:- Old glass door / partitions be removed and making good jambs, cills with the similar adjacent materials. |
| 139 | S&F door closer hydraulically regulated designation No. 3 universal type cast iron body suitable for door shutters of 851 to 1000mm in width and fixed complete all as specified and directed by Eng-in-charge. |
| 140 | S&F 300mm mild steel (Helical door spring) ordinary rat tail rod pattrern spring including roller and roller plate complete with necessary welding work complete all as specified and directed. Please Enable Macros to View BoQ information |
