|
| 1 | Repair to potholes any depth, not exc 1 sq m each including sweeping free from dust and mud, or water, scoring sunken surfaces in roads, paths, etc. cutting around edges to at least 25mm in depth, making good by filling in screened & graded road metal, watering and well ramming (including supply of road metal) complete all as specified. |
| 2 | Preparing surfaces by brushing with wire brushes for removing caked mud etc. sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etc.Complete all as specified and directed By Engineer-in Charge |
| 3 | M&L Applying evenly a tack coat of Cationic Bitumen Emulsion (RS-1) conforming to IS: 8887 at a rate of application of 0.2-0.3 kg/sqm on bituminous surface as specified in Table 500-5 of MaRTH specification for road and bridge works 2013, using mechanica sprayer after cleaning of existing surface as specified and Directed By Engineer-in-Charge |
| 4 | M&L For Bituminious premix semi dense asphaltic Concrete (SDAC),30mm thick (consolidated thickness)in single layer using paving bitumen VG-30 with 5.5%Binder content mixed in hot mix plant using design mix and laid by mechanical paver and rolled and compacted with using 8 to 10 tonne cap vibratory power roller to achieve the required compactness, camberand gradient finished complete including (cutting of Edge of road -straight and site clearance )etc Complete all as specified and Directed by Engineer-in-Charge |
| 5 | Scarifying or picking gravelled, macadam or bituminous macadam surfaces in area exc 400 sqm Exc 50 mm and n exc 100 mm deep Unsurfaced Water Bound Macadam surfaces for removingcaked mud etc. sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dirt etcComplete all as specified and Directed By Engineer-in-Charge |
| 6 | M&L Applying evenly a prime coat of Cationic Bitumen Emulsion SS1 confirming to IS: 8887 at a rate o application of 0. 7-1 kg/sqm on surface o WMM/WBM/BM as specified in Table 500-3 of MoRTH specification for road and bridge works 2013, using mechanical sprayer complete all as specified and directed . |
| 7 | M&L Premix bituminous, using 4% binder of VG-30 grade of paving bitumen, macadam laid/rolled and compacted to required gradient and camber (consolidated thickness upto 75mm thick) complete all as specified. |
| 8 | M&L for 100mm thick Moorum/Red bajri, spread, rolled, consolidated & gradient and camber required all as specified and directed |
| 9 | Dismantaling Stone slabs and tiles laid Dry and Pointed of any description or thickness in floors, aprons etc. |
| 10 | M&L For Sand Stone kerb of roughly squared stones of size 15cm x 30cm, dressed so that the maximum depression from a straight edge held against the dressed surface shall not exceed 6mm for top and exposed surfaces of sides and 20mm for the rest of surfaces jointed in cement mortar1:6 and struckflush complete all as specified and directed by Engineer-in-Charge |
| 11 | Demolition of PCC in Ground Floor and paving n exc 15 cm (below or above ground level).complete all as specified and directed by Engineer-in-Charge |
| 12 | M&L for PCC type D2 1:4:8 using 40mm graded stone aggregate, 100 mm thick as in sub base , complete all as specified and directed. |
| 13 | M&L Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete. |
| 14 | Demolition of precast concrete articles and other similar works all as specified and directed. |
| 15 | M&L Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete. |
| 16 | M&L for marking 2.50 mm thick centre line, stop line, dashes, arrows, brackets & similar etc. and the like exc 10cm wide on road surfaces as per IRC pattern with thermo plastic paint of approved quality & make with 8% glass beads laid at temperature 160 C with a special applicator machine complete all as per manufacturer's instructions & traffic diversion arrangement . |
| 17 | Supply and fix in repair solar cat eye aluminum alloy shall (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono rystafie solar panel 2.4V/0.3 watt one NI-ed rechargeable battery (1.2V/1600MA) consisting of super bright LED with 10,000 to 18,000 mcd completed as per manufactures instructions etc. all as specified and directed |
| 18 | Supply and fixing in repair cat eye bothside reflective type of aluminium metal body alloy of size 110mm x 120mm x 20mm with PAMA striplens reflector of model No. DA 972.0 to be fixed with specified epoxy adhesive material as per manufactures instructions. |
| 19 | M&L Manufacturing, supplying and fixing retro reflective Cautionary /warning sign boards of equilateral triangular shape having each side of 900 mm with support length of 3650 mm and made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue and silver white or other colourcombination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mmat the bottom end and including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromate yellow primer (vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with two or more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing , specification and direction of Engineer-in-charg |
| 20 | Supply and fixing in repair metal tubular dealineator made out of ABS round body fitted with 2 Nos 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in PCC 1:2:4 (150x150x300mm) type B1 complete all as specified and directed Please Enable Macros to View BoQ information |
