|
| 1 | Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed. |
| 2 | S&F portions framed & hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks & similar work conforming to Fe 290-0 Gde E-165 complete all as specified and directed. |
| 3 | Repair/servicing of automatic sliding glass door (sensor operated) of clear opening size 3.00 m width × 2.50 m height (approx area 7.50 sqm), complete all as specified and directed., comprising inspection and fault finding of complete all as specified and directed. system including motor, track, rollers, guide rails, sensors, control unit and allied fittings to identify cause of vibration during operation; dismantling and refixing of shutters and components as required; realignment/adjustment of track, guide rails, frame and shutter system to eliminate vibration and ensure smooth sliding; replacement of minor defective parts such as rollers, bearings, belts, brushes, rubber gaskets, stoppers, fasteners etc.; tightening of all fittings including nuts, bolts, screws, clamps and glass supports; servicing and lubrication of all moving parts including rollers and tracks with suitable lubricant; checking and rectification of electrical system including motor, wiring, control panel and sensor alignment/calibration; complete all as specified and directed. testing and commissioning to ensure smooth, noiseless and vibration-free operation, including all labour, T&P, scaffolding, consumables and incidental charges complete all as specified and directed. |
| 4 | M&L for preparation of new or previously untreated steel or iron surfaces of any description over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed. |
| 5 | M&L for cement concrete type B1 1:2:4 (using 20mm graded stone aggregates) in precast cover slabs for manholes cover and similar articles with plain faces etc set in cement mortar 1:4 including use and waste of formwork and including demoiltion of precast cover slab for manholes complete all as specified and directed. |
| 6 | M&L for TMT bar 8mm dia and over cut to length bent to shape reqd incl cranking bending etc complete all as specified and directed. & binding with MS wire (annealed) not less than 0.9mm dia in reinforcement complete all as specified and directed. |
| 7 | Providing 25mm thick, using 12.5 mm graded stone aggregate precast cement concrete louvres and jallies, Type B0 1:2:4 setting in CM 1:6 including all mouldings complete all as specified and directed. |
| 8 | Demolition of Cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) un-reinforced cleaning the premises and removal of rubbish out side the MD land complete all as specified and directed. |
| 9 | M&L for precast concrete solid block masonry exc 10cm width with solid block of PCC (1:5:8) Gde D-5 and setting in CM 1:6 and including demolition of old brick work/Stone masonary/PCC block masonary built in cement morter of any description and removing of rubbish out side MD land at the location notified by the municipal authorities complete all as specified and directed. |
| 10 | Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish out side MD land at the location notified by the municipal authorities complete all as specified and directed. |
| 11 | M&L for 75mm thick (1:3:6) Type-C2 (using 40mm graded crushed stone aggregate) as in plinth protection/path finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed. |
| 12 | M&L for plain cement concrete (1:4:8) Type-D2 (using 40mm graded crushed stone aggregate) as in levelling course/sub base of flooring complete all as specified and directed. |
| 13 | M&L for providing cement concrete (1:2:4) B-1 using 20mm graded aggregate as in copings/haunching/bearing course over brick walls etc and like complete all as specified and directed. |
| 14 | M&L for non skid ceramic coloured tiles 600X600 7 to 8 mm thick in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 15mm thick screed bed of CM 1:6 complete all as specified and directed. |
| 15 | All as per srl item no 14 above but in skirting over and including 10mm thick backing coat in CM 1:3 complete all as specified and directed. |
| 16 | M&L for coloured glazed ceramic tiles in vertical surface 300x450x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10mm thick backing coat of CM 1:3 complete all as specified and directed. |
| 17 | M&L for Non - skid ceramic coloured tiles, size 300x300x7 mm thick laid on floor, over and including 15mm thick screed bed in cement slurry and pointed in white cement with pigment to match the shade of the tiles, complete all as specified and directed. |
| 18 | M&L for rubber moulded glossy chequered cement concrete coloured tiles 30cm x 30cm x 20mm thick, set, jointed and pointed in neat cement slurry in floors over and including 20mm thick screed bed in cement mortar 1:6 complete all as specified and directed. |
| 19 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 20 | Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc complete all as specified and directed. |
| 21 | M&L for 20mm thick granite (of any type) work table rubbed and pre polished) in cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixtures of pigment to match with shade of granite complete all as specified and directed. and ensure best adhesion to surface complete all as specified and directed. |
| 22 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed. |
| 23 | M&L for machine cut cudappah stone slab 20-25mm thick for vertical supports of kitchen platforms and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing of the exposed face complete all as specified and directed. |
| 24 | M&L for machine cut kota stone slab flooring 20- 25mm thick over and including 20mm screed bed CM(1:4) cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. |
| 25 | Mirror polishing on marble/granite/Kota stone/stone work where ever required to give high gloss finish and including minor grindig complete all as specified and directed. |
| 26 | M&L for rendering 15mm thick on stone masonary surfaces other than fair faces of brick surfaces work or stone surfaces in CM 1:6 finished even and smooth without using extra cement including taking down of cement plaster complete all as specified and directed. |
| 27 | M&L for rendering 15mm thick in CM 1:4 on brick/stone surfaces finished even and smooth without using extra cement including taking down of cement plaster complete all as specified and directed. |
| 28 | All as per srl item no 27 above but 10mm thick in CM 1:3 as in ceiling complete all as specified and directed. |
| 29 | M&L for preparation newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed. |
| 30 | M&L for preparation newly plastered surfaces of wall and applying two coats of cement base paint over a coat of primer of same make over external wall surfaces complete all as specified and directed. |
| 31 | M&L for preparing new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer of same make over a thin layer of wall care putty complete all as specified and directed. |
| 32 | M&L for preparing old plastered surfaces of walls and applying two coats of oil bound distemper over 1mm thick wall care putty including complete removal of existing treatment of any layer on wall complete all as specified and directed. |
| 33 | M&L for preparing old plastered or unplastered surfaces of walls and applying two coats of oil bound distemper complete all as specified and directed. |
| 34 | M&L for preparing old plastered or unplastered surfaces of walls and applying one coat of oil bound distemper complete all as specified and directed. |
| 35 | M&L for preparing old plastered surfaces of ceiling and applying one coat of oil bound distemper complete all as specified and directed. |
| 36 | M&L for preparation of old plastered surfaces of wall/Ceiling by brooming/wire brushing/removal of loose scales/dusts/unwanted particles manually/mechaincally and applying one coat of white wash complete all as specified and directed. |
| 37 | M&L for preparing old plastered surface of walls and applying one coat of cement based paint complete all as specified and directed. |
| 38 | complete all as specified and directed. removal of old decorated surface of wall preparation old plastered surfaces of wall and applying Finishing walls with Acrylic Smooth exterior paint of required shade, Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified and directed. |
| 39 | M&L for preparation of old steel surfaces of any description and applying one coat of synthetic enamel paint of selected colour complete all as specified and directed. |
| 40 | M&L for preparation of old wooden surfaces of any description and applying one coat of synthetic enamel paint of selected colour complete all as specified and directed. |
| 41 | DismantlingWall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillet complete all as specified and directed. |
| 42 | M&L for 8 mm thick one side laminated gypsum ceiling board for false ceiling of size 600 x600x mm on GI powder coated grid work 60 cm x 60 cm with using 36.5 mm x 23.5 mm x1.5 mm thick main tee, 23.5 x 23.5 mm x 1.28 cross tee and 25 x 25x 1.5 mm angles fixed to perimeter of wall for false ceiling including necessary supporting hanger with 4.0 mm dia GI wire and 'J' bolts washer nuts for securing frame work to ceiling suspended @ 120 cm C/C both ways, size of grid shall be 605 x 605 mm, complete all as specified and directed. |
| 43 | M&L for 12mm thick Seamless calcium silicate ceiling made of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seamless finish with and including Gl frame work size of grid (605 mm x 605 mm) direction of Engr-in-charge as per site reqmt seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre with and incl thin layer of putty with gypsum binder, sanding the sufrace till smooth surface is obtained and applying two coats of oil bound distemper over acoat of primer complete all as specified and directed. |
| 44 | S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick, AZ-150 grade of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including dismantiling of sheets as in roofing/cladding complete all as specified and directed. |
| 45 | S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick, AZ-150 grade of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, bent to shape as required and directed fixed with self tapping screws including dismantling of sheets in roofing/cladding complete all as specified and directed. |
| 46 | S&F 2mm thick fibre glass reinforced translucent sheeting fixed with coach screw and washer in roof/wall cladding etc including dismantling of sheets as in roofing/cladding complete all as specified and directed. |
| 47 | Dismantling timber scantling, framed in post, rafters, purlines etc over 40 sqcm in section where necessary complete all as specified and directed. |
| 48 | M&L for MS structural steel work, framed as in trusses purlins, rafter, post etc conforming to grade E-250 (Fe-410W, quality A) including shaped washers including necessary cutting required length, notching drilling, riveting and or welding or connecting with nut bolts with angle cleats, fish plat, gusset plate and also erecting in true position complete all as specified and directed. |
| 49 | S&F 15 mm dia steel water GI tube medium grade with all fittings/connections & MS clamps/clips and necessary screwing as reqd and fixed with or without concealed to walls & surface of roof slab with and including making good to required surfaces by using white cement and including taking up or down 15mm bore steel/composite/UPVC tubing and connection from any position concealed/exposed complete all as specified and directed. |
| 50 | S&F 20 mm dia steel water GI tube medium grade with all fittings/connections & MS clamps/clips and necessary screwing as reqd and fixed with or without concealed to walls, ceilings or laid in floors including taking up or down 20mm bore steel/composite/UPVC tubing and connection from any position concealed/exposed complete all as specified and directed. |
| 51 | S&F rotational moulded polythene water storage tank 500 ltrs (cylindrical vertical with closed top) hoisted and fixed in position incl dismantling of existing water tank of any capacity all as specified in SSR Part-I complete all as specified and directed. |
| 52 | S&F rotational moulded polythene water storage tank 1000 ltrs (cylindrical vertical with closed top) hoisted and fixed in position incl dismantling of existing water tank of any capacity all as specified in SSR Part-I complete all as specified and directed. |
| 53 | S&F in repair vitreous china single piece pedestal pattern water closet white 'P' or 'S' trap, matching sheet cover and connection to trap . including making good to floor, complete all as specified and directed. |
| 54 | S&F in repair 15mm bore chromium plated bib cock fancy type complete all as specified and directed. |
| 55 | S&F in repair 15mm bore chromium plated angle cock fancy type complete all as specified and directed. |
| 56 | S&F in repair Brass CP wall mixer 3-in-1 for mixing hot & cold water with provision for both hand shower and overhead shower complete all as specified and directed. with 115mm long bend pipe, connecting legs & wall flange and fixed complete all as specified and directed. |
| 57 | S&F in repair brass chromium plated overhead shower 100mm round shape single flow with rubit cleaining system fitted to steel pipe or union complete all as specified and directed. |
| 58 | S&F in repair 15mm bore chromium plated pillar cock fancy type complete all as specified and directed. |
| 59 | S&F in repair health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.00 metre long flexible tube and wall hook including making connections and fixed in position complete all as specified and directed. |
| 60 | S&F in repair for Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 10cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed. |
| 61 | S&F in repair chromium plated soap dish approximate size 120x 120x28mm complete all as specified and directed. |
| 62 | S&F in repair tubular towel rail, 20mm dia, D type, 60cm longv between flanges complete all as specified and directed. |
| 63 | S&F in repair 2-way Bib cock with flange complete all as specified and directed. |
| 64 | S&F 15 mm dia PVC connections, 450 mm long with PTMT nuts of suitable size at two end complete all as specified and directed. |
| 65 | Supply and fixed in repair 20mm bore PVC brass valve, high pressure with polythene float and fly nut complete all as specified and directed. screwed for iron pipe or brass ferrule complete all as specified and directed. |
| 66 | Supply and fixed in repair 20mm dia gun metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 67 | S&F Stainless Steel Kitchen rack (Overall size 24x24x10”) complete all as specified and directed. Make : Cat No. P-310 of Prayag/Blue Star/Nirali |
| 68 | S&F in repair vitreous China, squatting pan, Orissa Pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) with PTMT trap of suitable size ( P or S type) including connection to trap and to flushing pipe, anti syphonic pipe etc complete including provision of cement concrete bedding & making good to floor complete all as specified and directed. |
| 69 | S&F in repair 10 Ltr capacity PVC valveless syphonic action type flushing cistern low level white, with inlet, ball valve, float and handle including PVC flush pipe and brackets fixed in wall and floor to trap of WC as reqd complete all as specified and directed. |
| 70 | Supply and fixing in repair 600mm X 450mm bevelled edge mirror of selected quality mounted on plastic frame covered back with commercial and fixed on wooden plug with chromium plated brass screws and cup washer complete all as specified and directed. |
| 71 | Supply and fixed in repair sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to arf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 72 | Supply and fixed in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed. |
| 73 | S&F in repair Vitreous China wash basin, white/coloured, flat back, size 550x400mm excluding taps, waste chain & plug & porcelain stopper but including brackets and 32mm dia 1mtr long PVC waste pipe complete all as specified and directed. |
| 74 | S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern & flush pipe) including health faucet complete all as specified and directed. |
| 75 | Dismantling cast iron work of any de scription and in any position complete all as specified and directed. |
| 76 | S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. |
| 77 | All as per srl item no 76 above but 75mm bore. |
| 78 | S&F 110mm PVC (SWR) bands complete all as specified and directed. |
| 79 | S&F 75mm PVC (SWR) bands complete all as specified and directed. |
| 80 | S&F PVC (SWR) Nahani trap 75mm bore with SS grating with or without holes incl jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed. |
| 81 | S&F PVC (SWR) cowl 75/100mmdia as required complete all as specified and directed. |
| 82 | S&F 110mm bore PVC (SWR) junction double, (double T) equal or unequal with access door complete all as specified and directed. Please Enable Macros to View BoQ information |
