Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) over areas (exceeding 30cm in depth,1.5m in width as well as10sqm on plan) including getting out and disposal of excavated earth lead upto 50m and liftupto1.5m, as directed by Engineer-in-charge.All kinds of soil |
| 2 | Filling availableexcavatedearth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm indepth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 3 | Supply and stacking of Fly ash conforming to IRC- 58 at site, including carriage, loading , unloading & stacking up to any lead (measured stacks will be reduced by 20% for payment). |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : a) 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 5 | b) 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 6 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 7 | Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size). |
| 8 | Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil. |
| 9 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement- All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 10 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size) |
| 11 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). |
| 12 | Steel reinforcement for R.C.C.work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 13 | Centering and shuttering including strutting, propping etc. and removal of form for a) Foundations, footings, bases of columns, etc. for mass concrete |
| 14 | b) Suspended floors, roofs, landings, balconies and access platform |
| 15 | c) Lintels, beams, plinth beams, girders, bressumers and cantilevers |
| 16 | d) Columns, Pillars, Piers, Abutments, Posts and Struts |
| 17 | d) Shelves (Cast in situ) |
| 18 | e) Weather shade, Chajjas, corbels etc., including edges |
| 19 | f) Arches, domes, vaults up to 6 m span |
| 20 | g) Small surfaces suchas cantilever ends, brackets andendsof steps, caps and bases to pilasters and columns and the like |
| 21 | h) Small lintelsnotexceeding1.5mclear span,mouldingas incornices,window sills, string courses, bands, copings, bed plates, anchor blocks and the like |
| 22 | Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement :6 coarse sand: 12 graded stone aggregate 20 mm nominal size) upto plinth level with :Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 23 | Providing and fixing up to floor five level precast cement concrete solid block, including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering complete :1:3:6 (1 Cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 24 | Providing and fixing up to floor five level precast cement concrete solid block, including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering complete :1:3:6 (1 Cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 25 | Stone work (machine cut edges)forwall liningetc. (veneer work) upto 10 metre height, backing filled with a grout of average12mm thick cement mortar 1:3(1 cement :3 coarse sand) including pointing in white cement mortar 1:2(1 white cement: 2 stone dust) with an admixture of pigment matching the stone shade: (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) : White sand stone - exposed face fine dressed with rough backing . 30 mm thick |
| 26 | Stone work, plain in copings, cornices, string courses and plinth courses, upto 75mm thick in Cement mortar 1:6 (1 cement : 6 coarse sand), including pointing with white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixtureof pigment matching the stone shade.Red sand stone |
| 27 | Providing and fixing 18mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade,colour and texture laid over 20mm thick base cement mortar 1:4(1cement: 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high glossfinish etc. complete at all levels. Granite of any colour and shadeArea of slab upto 0.50 sqm |
| 28 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. |
| 29 | Providing and fixing ISI marked flush door shutters conforming to IS:2202 (PartI) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:a) 35mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 30 | b) 30mm thick including ISI marked Stainless Steel butt hingeswith necessary screws |
| 31 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick |
| 32 | uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length(shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic capsand necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at allcorners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware'sand drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall befilled with weather proof silicon sealant over backer rod of required size and of approved quality, allcomplete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes andsilicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth& width of profile shall be acceptable.uPVC profile should be tested by BSI(UK) & SKZ(Germany) @25000 weathering hours Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wallthickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.) |
| 33 | Providing and fixing factory made uPVC white colour sliding glazed window upto1.50 m in heightdimension comprising of uPVC multi-chambered frame with in built roller track and sash extrudedprofiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll formingprocess of required length (shape & size according to uPVC profile), appropriate dimension of uPVCextruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powdercoated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 41kg), G.I fasteners 100 x 8mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holesfinished wall shall be filled with weather proof silicon sealent over backer rod of required size and ofapproved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single /double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profiledimension in higher side shall be accepted but no extra payment on this account shall be made. Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm bothhaving wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriatedimension . (Area of window above 1.75 sqm upto 2.50 sqm). |
| 34 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5.50 mm thickness |
| 35 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc.complete :300x16 mm |
| 36 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc.complete :300x10 mm |
| 37 | Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.125 mm |
| 38 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC10 as per IS:1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper |
| 39 | Providing and fixing traditionally carved wood work (Shingstak) over doors and windows including all accessories as per the direction of the Engineer in-charge, complete with;2nd class kail wood |
| 40 | Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercialProfile BFixing with adjustable lugs with split end tail to each jamb |
| 41 | Steel work welded in builtup sections/framed work, including cutting, hoisting, fixing in position and In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 42 | Providing and fixing stainless steel (Grade304) railing made of Hollow tubes, channels, plates etc.including welding ,grinding, buffing, polishingand making curvature (wherever required) and fitting the same withnecessary stainless steel nuts and bolts complete ,including fixing the railingwith necessary accessories and stainless steel dash fasteners, stainless steelbolts etc. of required size, on the top of the floor or the side of waist slabwith suitable arrangement as per approval of Engineer-in-charge, (forpayment purpose only weight of stainless steel members shall be consideredexcluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 43 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent |
| 44 | Providing & fixing in position Phenol bonded Bamboowood flooring with planks of sizes 14mm thick,minimum 1800mm length and minimum 100 mm wide, in approved colour, texture and finish, havingPerformance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council(BMTPC). The flooring shall be fixed with tongue and groove interlocking system, with underlayment of4mm thick expanded polyethylene foam sheets having density 40kg/cum, over prepared surface withnecessary quarter round planks of size 1900mm x 18mm and door reducer of size 1900mm x 44mm,wherever required.The Hardness 1000 Kgf. with Eco friendly UV coating, all complete as per direction of the Engineer in-bamboowood planks shall have minimum density of 1000 Kg/cum & minimum charge. |
| 45 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm |
| 46 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. |
| 47 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @3.3kg per sqm, including pointing in white cement mixed with pigment ofmatching shade complete. |
| 48 | Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :In 75x75 mm deep chase |
| 49 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 50 | Providing and fixing onwall face unplasticised Rigid PVC rain water pipes conforming to IS:13592 TypeA, including jointing with seal ring conforming to IS: 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diametre |
| 51 | Providing and fixing on wall face unplasticised-PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS:5382, leaving 10mm gap for thermal expansion. a) Single tee with door 110x110x110 mm |
| 52 | b) Shoe (Plain) 110 mm Shoe |
| 53 | Providing and fixing unplasticised-PVC pipe clips of approved design to unplasticised-PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4(1 cement: 4 coarse sand) and making good the wall etc. complete. 110 mm |
| 54 | Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15cm diametre and weighing not less than 440 grams. |
| 55 | 12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand) |
| 56 | 15 mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1 cement: 6 coarse sand) |
| 57 | 6 mm cement plaster of mix :1:3 (1 cement : 3 fine sand) |
| 58 | Providing and applying white cement based putty of average thickness 1 mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 59 | Finishing walls with Acrylic Smooth exterior paint of required shade :Newwork (Twoormorecoat [email protected] ltr/10 sqmover and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) |
| 60 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :Newwork (two or more coats)over and including water thinnable priming coat with cement primer |
| 61 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture |
| 62 | Providing and applying high performance, pure polyurethane based, single component, low VOC, elastomeric, seamless, moisture curing, waterproof membrane, for waterproofing treatment to the RCC Structure in roof slab with, applied in 2 coats with roller at a total consumption of 1.5 Kgs/Sqmt, having specific gravity of minimum 1.30, having an elongation capacity of over 400 %, with tensile strength of > 2.00 Mpa, Adhesion to concrete surface over 2.00 N/mm 2, Shore A Hardness of 75, Fire resistance EURO Class-F, with Anti-root propertise, with a service temperature range of -40 deg C to 80 deg C, with solids content of around 90%, to be applied by brush/raller over the RCC slab and on the vertical surfaces upto 300 mm above FFL, thereafter ponding with water for 3 days etc. complete. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guaranteed for 10 years against any leakage. |
| 63 | Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat cover, and cistern fittings,nuts, bolts and gasket etc complete. |
| 64 | Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan. |
| 65 | Providing and fixing 8mm dia C.P./S.S. Jet with flexible tube upto1metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 66 | Providing and fixing wash basin with C.I.brackets, 15mm C.P.brass pillar taps, 32mm C.P. brasswaste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :White Vitreous China Wash basin size 630x450mm with a pair of 15mm C.P.brass pillar taps. |
| 67 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink with drain board 17.10.1.1 510x1040 mm bowl depth 250mm. 510x1040 mm bowl depth 225mm. |
| 68 | Providing and fixing cockroach trap S.S grating of approved design for floor traps etc. including setting in floor with cement mortar. 100mm dia |
| 69 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15mm nominal bore. |
| 70 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. |
| 71 | Providing and fixing C.P.brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.15mm nominal bore. |
| 72 | Supplying, installation, testing and commissioning approved make 15mm CP health faucet with CP flexible tube 1.2m long and wall hook (model no. HF 1801 Acquaviva make). Having high quality plating in compliance with DIN and EN standards including CP crutch, nozzie and 2 way bib cock with wall flange etc complete. HF-1812. (Make: kitch/jaquar/cardin). |
| 73 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing : Rectangular shape 453x357mm |
| 74 | Providing and fixing 3 layer PP-R(Polypropylene Random copolymer) pipes SDR 7.4UV stabilized & anti-microbial fusion welded, having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes testing of joints complete as per direction ofEngineer inCharge. (Internal work exposed on wall) a) PN - 16 Pipe, 25mm OD (SDR-7.4) |
| 75 | b) PN - 16 Pipe, 32mm OD (SDR-7.4) |
| 76 | Providing and fixing 3 layer PP-R (Polypropylene Random copolymer)pipes SDR 7.4UV stabilized & anti-microbial fusion welded, having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings i/c fixing the pipe with clamps at 1.00m spacing.This includes the cost of cutting chases and making good the same including testingof joints complete as per direction of Engineer in Chajge.(Concealed work including cutting chases and making good the walls etc.,)PN-16 Pipe, 20 mm OD (SDR-7.4) |
| 77 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end):a) 25 mm nominal bore |
| 78 | b) 32 mm nominal bore. |
| 79 | Providing and fixing brass ferrule with C.I.mouth cover including boring and tapping the main : 20 mm nominal bore |
| 80 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI :12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and over flow pipes but without fittings and the base support for tank |
| 81 | Providing and fixing ball valve (brass) of approved quality complete: High or low pressure with plastic floats: 25 mm nominal bore |
| 82 | Providing and fixing unplasticised-PVC poly vinyl chloride (UPVC) SWR pipes fittings type B for sewage waste discharge system (IS:13592 : 1992 marked) of approved quality/make supreme, jain pipes, sudhakar, prince or equivalent a) 100mm dia |
| 83 | b) 75mm diameter |
| 84 | Providing and fixing unplasticized poly vinyl chloride (UPVC) SWR pipes fittings type B for sewage waste discharge system (IS:13592: 1992 marked) of approved quality/make Bend of required degree with access door a) 100mm dia |
| 85 | b) 75mm dia |
| 86 | plain bend of required degree a) 100mm dia |
| 87 | b) 75mm dia |
| 88 | Heel rest sanitary bend a) 100mm dia |
| 89 | b) 75mm dia |
| 90 | Providing and fixing square-mouth S.W. gully trapgrade ‘A” complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300mm size (inside) the weight of cover to be not less than 4.50kg and frame to be not less than 2.70 kg as per standard design : 180x150 mm size P typeWith common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 91 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 92 | Providing and layingn on-pressure NP 2 class (light duty) R.C.C.pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2(1 cement:2 fine sand) including testing of joints etc. complete : a) 150mm dia. R.C.C. pipe |
| 93 | b) 250 mm dia. R.C.C. pipe |
| 94 | Providing and fixing of material for the insulation of pipe with nitrile tube , tapping with cello tape , Rockwood 6 inch per side, wire mesh, polythene , tapping with cello tape aluminum sheet 26 gauge cladding with dia . complete job including carriage. 19 mm thick, 50 mm dia (OD) ( PPR 32 mmm) |
| 95 | Providing and fixing of material for the insulation of pipe with nitrile tube , tapping with cello tape for inner wall fittings . complete job including carriage. 19 mm thick, 50 mm dia (OD) ( PPR 25 mmm) |
| 96 | Providing and fixing of material for the insulation of Water Storage Tank of with nitrile sheet , tapping with cello tape , Rockwood 6 inch per side, wire mesh, polythene , aluminum sheet 26 gauge cladding with dia of , complete job. 19 mm thick nitrile sheet |
| 97 | Providing and fixing heat tape 33Watt on PPR pipes made of denforced or chromelox or equivalent make, as approved by Engineer InCharge , complete Job |
| 98 | Carriage of material from source to site including loading, unloading and stacking complete job. A) Cement an average lead of 25km |
| 99 | b) Sand an average lead of 25km |
| 100 | c) Stone aggregate an average lead of 25km |
| 101 | d) Stone an average lead of 15km |
| 102 | Trenching in ordinary soil upto a depth of 60cm including removal and stacking of serviceable materials and then disposing of by spreading and neatly levelling with in a lead of 50m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or/and manure before and after flooding trenchwith water (excluding cost of imported earth, sludge or manure). |
| 103 | Supply and installation of pop up sprinklers pop up Impact rotors 3/4\\" inlet an radius ranging from 7-12m with interchangeable nozzles with check valve and all accessories complete as per BIS standard specifications and setting flow rate as directed. |
| 104 | Supplying and stacking of good earth at site including royalty and carriage upto 1km (earth measured in stacks will be reduced by 20% for payment). |
| 105 | Supplying and stacking sludge at site including royalty and carriage upto 1km (sludge measured in stacks will be reduced by 8% for payment), |
| 106 | Supplying and stacking at site dump manure from Badli or other approved source, including carriage upto1km manure measured in stacks will be reduced by 8% for payment):Screened through sieve of I.S. designation 20mm |
| 107 | Fine dressing the ground. |
| 108 | Mixing earth and sludge or manure in proportion specified or directed. |
| 109 | Spreading of sludge, dump manure or/and good earth in required thickness (Cost of sludge, dump manure or/ and good earth to be paid separately). |
| 110 | Grassing with ‘Doob’ grass including watering and maintenance of the lawn for 30days or more till the grass forms a thick lawn free from weeds and fit for mowing including supplying good earth if needed (the good earth shall be paid for separately). In rows 5 cm apart in either direction. |
| 111 | Providing and fixing selection no.1 grass turf with earth 50mm to 60mm thickness and ramming with required wooden tools, rolling with light roller to make the surface smooth and even |
| 112 | Renovating lawns including weeding, cheeling the grass, forking the ground, top dressing with sludge or manure, mixing the same with forked soil, watering and maintaining the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for mowing and disposal of rubbish as directed, including supplying good earth if needed but excluding the cost of sludge or manure (the good earth shall be paid for separately). |
| 113 | Preparation of beds for hedging and shrubbery by excavating 60cm deep and trench- ing the excavated base to a further depth of 30cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, levelling etc. includingstacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling as directed, within a lead of 50m lift upto 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately). |
| 114 | Planting flower beds including digging 30 cm deep bed sqm and refilling of beds with excavated soil and FYM 0.0508 cum per sqm , Fertilizer DAP 50 gms and insecticides chlorpyriphos 10ml per sqm , planting of F1 hybrid well bloomed flower saplings to be supplied in polybags at 25cm distance from plant to plant and row to rowminimum 15 no . plants per sqm |
| 115 | Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) Holes 60 cm dia and 60 cm deep. |
| 116 | Supply and Planting rare and specimen tree plants in already prepared pits (Ficus starlight 150 cm height , Terminalia 210 cm height, menatalis , Michelia champaca hybrid more than 180 cm height, Cyprus (Golden juniperous) more than 180 cm height, topiary of 1 O to 12 no. well trimmed bolls of more than 30cm size of Ficus nuda, Ficus retusa, Ficus long island , Ficus panda more than 180 cm height, Golden bottle brush , casurina equistefolia , Bottle palm with stem circumference at base more than 40cm ,Washingtonia palm of healthy clear stem height below leaf more Thant 90 cm) including , fertilizer and insecticides chlorpyriphos 20 ml per pit, planting of 180cm to 210cm tall sapling in position and flooding with water .specie of plant will be decided by engineer in charge. |
| 117 | Providing and displaying of Areca Palm plant, having ht. 2.40 m to 2.70 m with 12 to 14 suckers, well developed, fresh and healthy with lush green foliage in 35 cm size of poly bag & as per direction of the officer-in-charge. |
| 118 | Supply and stacking of Plumeria alba plant of height 165-180 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge. |
| 119 | Providing and displaying of Raphis Palm plant, having ht. 75 cm to 90 cm with 15 to 18 equal suckers, well developed, full of fresh and healthy leaves from bottom to top in 35 cm PVC Pots/C.Pots & as per direction of the officer-in-charge. |
| 120 | Providing and fixing M.S. flat iron tree guard 60cm dia. and 2m height above ground level formed of 4 nos. 25x6mm and 8 nos. 25x3mm vertical M.S. flats rivetted to 3 nos. 25x6mm M.S. flat iron rings in two halves, bolted together with 8mm dia. and 30mm long bolts including painting two coats with paint of approved brand and manufacture over a coat of priming, complete in all respects. |
| 121 | Providing and fixing of Tuflex Garden fencing Hexagonal net/or equivalent of green colour having contents ( Weight grams/sqm. 510 (+/- 8%)) in width of 60 cm. with bamboo of 90 cm. length. The bamboo should be painted with green colour paint of approved brand and manufacture (two or more coats) and fixed 30 cm. below ground level and 60 cm. above ground level at a distance of 1.50 mtrs. The net and bamboo should be binded with 2 mm. G.I. Wire at three places properly as per direction of Engineer-in-charge. |
| 122 | Supply and stacking of Allamanda cathartica plant of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge. |
| 123 | Supply and stacking of Bougainvillea (Variety Butiana, Lady Mary Baring, Mahara, Mohan, Scarlet Queen, Varigata, Glabra Formosa, Peruviana Odissi, Partha, Subhra,Thimma, Spectabilis L.N Birla, Refulgens) plant of height 30 cm. to 45 cm. with 2-3 branches in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge. |
| 124 | Providing and fixing vertical garden panels on aluminium tube (50 x25 x 1.5 mm) frame, or 1 B.85 kg per sqm weight MS angle and MS pipe frame fixed on wall, with growing media of coco peat, perlite and vermiculite 2:1:1, amended with fertilizers and plants as specified by the engineer in charge including drip irrigation of Netafem, Harvel, Hunter, Rain bird, Jain irrigation systems minimum BIS Standard material , planter used should be virgin plastic, , plants supplied should in coco peat and vermiculite medium and every plants should be of permanent decorative quality height of plants should be 30cm to 45 cm .complete. Outdoor vertical garden |
| 125 | Chair type garden bench with L-shaped sides made of reinforced concrete (M30), thickness 100 mm, overall height 1000 mm, base width 620 mm. Back and seat shall consist of 5 Nos. reinforced concrete planks 1500 mm x 100 mm x 50 mm one plank 1500 mm x 200 mm x 50 mm. Seating height of the bench shall be 450 mm. The bench shall be fixed with nuts on concrete mount, all holes sealed after assembly and installation. All materials required to be as per BIS specifications. |
| 126 | Rectangular garden bench with h-shaped sides made of reinforced concrete (M30), thickness 100 mm, back height 750 mm, base width 450 mm. Back and seat shall consist of rectangular reinforced concrete planks 1500 mm x 350 mm x 50 mm. Seating height of the bench shall be 450 mm. The bench shall be fixed with nuts on concrete mount, all holes sealed after assembly and installation. All materials required to be as per BIS specifications. |
| 127 | Providing and fixing pair of Plastic dustbins 100 litre volume each, of two different colours, for dry and wet waste, made of virgin plastic to be mounted on MS rectangular hollow section 50 x 25 x 3 mm frames pivoted on 3 MS square hollow section verticals, 1 m above ground, one 35 cm RHS welded to each vertical member at base and grouted in 180 x 40 x 30 cm 1:2:4 cement concrete. |
| 128 | Earth work in surface excavation not exceeding 30cm in depth but exceeding 1.5m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50m and lift upto1.5m, as directed by Engineer-in Charge:All kinds of soil |
| 129 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 130 | Extra for compaction of earth work inembankment under optimum moisture conditions to give at least 95% of the maximum dry density (proctor density). |
| 131 | Brick edging in full brick width and half brick depth including excavation, refilling and disposal of surplus earth lead upto 50 metres.With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 132 | Brick edging laid lengthwise with half brick depth including excavation, refilling and disposal of surplus earth lead upto 50 metresWith common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 133 | Providing and laying 75 mm thick compacted bed of dry brick aggregate of 40 mm thick nominal size including spreading, well ramming, consolidating and grouting with jamuna sand, including finishing smooth etc. complete as per direction of Engineer-in-charge. |
| 134 | Providing, laying and making kerb channel 30 cm wide and 50 mm thick with cement concrete 1:3:6 (2 cement: 3 coarse sand:6 graded stone aggregate 20mm nominal size) over 75mm bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth etc. complete and as per direction of Engineer-in-charge. |
| 135 | Providing and laying gang saw cut 18 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1cement : 5 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction ofEngineer-in-Charge.With granite stone of area less than 0.50 sqm. |
| 136 | Providing and laying matt finished vitrified tile of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (2 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge. |
| 137 | Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS:15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matchingpigments etc. complete as per direction of Engineer-in-Charge. |
| 138 | Providing and laying 60mm thick factory made cement in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid joints with line sand etc. all complete as per the direction of Engineer-in-charge. |
| 139 | Providing and fixing 10x10x7.50 cm Granite stone block hand cut and chisel dressed on top, for paving in floors, drains etc. laid over 20mm thick base mortar 1:4 (1 cement : 4 coarse sand) with joints 10mm wide filled with same mortar including ruled pointing etc. complete as per direction of engineer-in-charge. |
| 140 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). |
| 141 | Providing & making Gabion structure with Mechanically Woven Double Twisted Hexagonal Shaped Wire mesh Gabion Boxes as per IS 16014:2012,MORTH Clause 2500, of required size, Mesh Type 10x13 (D=100 mm with tolerance of ± 2%) Zinc coated, Mesh wire diametre 3.0 mm, mechanically edged/selvedged with partitions at every 1m interval and shall have minimum 10 numbers of openings per metre of mesh perpendicular to twist, tying with lacing wire of diametre 2.2mm, supplied @ 3% by weight of Gabion boxes, filled with boulders with least dimension of 200 mm, as per drawing, all complete as per direction of Engineer in-charge. |
| 142 | Providing and making wooden pergola over pathway with teakwood frames section including polishing as per design |
| 143 | The main frame of AERIAL STROLLER is to be made up of 80 NB G.I. pipes with G.I. plating up to 40 micron thickness. Two vertical pipes are to be supported by 80 NB G.I. Pipe. Suitably designed mounting flange assembly having circular flange of 130mm dia with 16mm thickness is to be provided for footrest assembly. Foot rest bend pipe is to be made up of 40 NB G.I. pipes. Foot rest is to be made with the help Aluminum casting. Bearings used are to be of oil sealed, self-lubricating. Make of bearing shall be as per approved make list. Handle is t o b e made by 25 NB G.I. pipes. All pipes is to be uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe are to be close by GI / PVC caps for user safety against entrapment. |
| 144 | 100NB GI main vertical support pipe of CHEST PRESS is to be fixed over 10mm thick base plate. Base plate shall have dia of 250mm & 10mm thick clamping plates is to be attached to main frame to hold the rest of assemblies. Seat should be of HDPE and it is to be fixed over seat frame. Seat frame is to be made of 40NB bend GI pipes. 25NB GI pipe is to be attached to seat frame to form a foot rest. The seat frame is to be hinged over vertical support pipe through 40NB GI pipe links with the help of specially designed bearing housings. Bearings used are to be of oil sealed, self-lubricating. Make of bearing shall be as per approved make list. Connecting link plates is to be 8mm thick. The handle is t o b e made of 25NB & 20NB GI pipes with PVC / rubber handle grip at its both ends. Handle is to be linked to the seat with 40NB connecting link which is to be hinged to main vertical support pipe with the help of bearing assembly. All pipes are to be uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe are to be close by GI / PVC caps for user safety against entrapment. |
| 145 | Wheel /Shoulder Twirl 25NB Galvanized pipe is to be bend to form ring and spokes consists of 15NB G.I. pipes which is to connected each other to form a wheel of Shoulder Twirl which having two quantities. This wheel is to be fixed to 80 NB main support galvanized pipe with the help of 40NB connector pipe with bearing housing. Bearings used are to be of oil sealed, self-lubricating. Make of bearing shall be as per approved make list. Nylon knobs are to be provided on the wheels for gripping purpose. All pipes are to be uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe are to be close by GI / PVC caps for user safety against entrapment. |
| 146 | Hand Rower - HDPE (High Density Poly Ethylene) seat with backrest is t o b e fixed over 40NB Galvanized bend pipe. This bend pipe is t o b e further linked to 80NB base pipe with help of connecting links. Connecting links s h a l l b e of 25NB G.I. pipes with bearing housings at ends. The paired 25NB pipe handle with rubber/PVC handgrip at the end is t o b e fixed over one of the connecting link. Connecting links is to be hinged in between seat frame and base frame with bush bearings. A suitable PVC/ rubber grip is t o b e provided for foot rest on seat frame. All pipes are to be uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe are to be closed by GI / PVC caps for user safety against entrapment. |
| 147 | The main frame of the Back Extension is to be made in 80 NB G.I. Pipes. The handle frame is to be made up of 25 NB G.I. pipe which is hinged to main frame by a suitably designed clamp. Rectangular pipe of size 50x25x3 mm thick is to be provided as supporting structure for Thigh Rest. Thigh rest or seats is to be made up of HDPE material. Foot rest is to be made up of HDPE material and attached to main frame with the help of 40 NB G.I. pipes. All pipes are to be uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe are to be close by GI / PVC caps for user safety against entrapment. |
| 148 | 100NB GI main vertical support pipe of SHOULDER EXECISER is to be fixed over base plate 250mm dia with 10mm thick base plate. 10mm thick clamping plates are to be attached to main frame to hold the rest of assemblies. HDPE seat is to be fixed over seat frame. Seat frame is to be made of 40NB bend GI pipes. 25NB GI pipe is to be attached to seat frame to form a foot rest. This seat frame is to be hinged over vertical support pipe through 40NB GI pipe links with the help of suitably designed bearing housings. Connecting link plates i s t o b e 8mm thick. The handle is t o b e made of 25NB & 20NB GI pipes. Handle is t o b e linked to the seat with 40NB connecting link which is to be hinged to main vertical support pipe with the help of bearing assembly. All pipes are to be uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe are to be closed by GI / PVC caps for user safety against entrapment. |
| 149 | Provising and fixing of AERIAL STROLLER is to be made up of 80 NB G.I. pipes with G.I. plating up to 40 micron thickness. Two vertical pipes are to be supported by 80 NB G.I. Pipe. Suitably designed mounting flange assembly having circular flange of 130mm dia with 16mm thickness is to be provided for footrest assembly. Foot rest bend pipe is to be made up of 40 NB G.I. pipes. Foot rest is to be made with the help Aluminum casting. Bearings used are to be of oil sealed, self-lubricating. Make of bearing shall be as per approved make list. Handle is t o b e made by 25 NB G.I. pipes. All pipes is to be uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe are to be close by GI / PVC caps for user safety against entrapment. |
| 150 | The main frame of ABS BOARD is to be made up of 50 NB G.I. pipes with leg support structure. The back rest is to be fixed over 40NB back rest frame. Back rest is to be made up of rectangular pipes of 50 X 25 X 3 mmthick. 3mm thick H D P E sheet is to be bolted on back rest to give an extra support. All pipes are to be uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe are to be closed by GI / PVC caps for user safety against entrapment. Two ABS Board has to be connected to spacer attachment with center support of 100nb G.I Pipe. |
| 151 | The main frame of Leg Press Double shall consist of 80 NB G.I. pipes with two suitably designed brackets attached on it. Brackets have to be made of M.S. material with G.I. plating. The moving frame of Leg Press is to be made of 40NB G.I. pipes which is to be mounted to the main frame with the help of suitably designed, machined shaft and bearing housing. Bearings used are to be of oil sealed, self-lubricating. Make of bearing shall be as per approved make list. Foot rest is to be hinged to the main frame with the help of suitably designed G.I. plated clamp and 25 NB G.I. pipes. Gusset plates have to be provided to give extra strength to foot rest. Foot rest is to made of high quality HDPE material. Suitably designed HDPE pads has to be provided at the bottom of moving frame. Seat and back rest provided has to be made of HDPE.. All pipes are to be uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe is to be close by GI / HDPE caps for user safety against entrapment. |
| 152 | The main frame of Double Hip Twister consists of 100 NB G.I. pipes with handle attached on it. Handle is to be made up of 25 NB and 15 NB G.I. pipes which forms a shape of wheel. The rotating discs is to be made from M.S. material with G.I. plating is to be supported over 80NB G.I. pipes stands with the help of suitably designed heavy duty bearings. The discs have to be bolted to main frame with the help of 40NB G.I. pipe. Three foundation stands, made of 80 NB G.I. pipes and G.I. plated M.S. round plates are provided All pipes is to be uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe are to be closed by GI / PVC caps for user safety against entrapment. |
| 153 | The main frame of Surf Board shall be of 100 NB G.I. pipes with handle attached on it. Handle pipe is to be made up of 25 NB G.I. pipes. Circle of 130mm dia & 16 mm thk is to be fixed to main frame in opposite direction to each other with the help of 50NB GI pipe. Bearing mounting assembly is attached this circular plate. . Bearings used are to be of oil sealed, self-lubricating. Make of bearing shall be as per approved make list.. Two handrails have to be attached to handle frame. These handrails have to be made of 40NB G.I. pipe. Foot rest is to be mounted on main frame with the help of suitably designed bearing for its free movement. Foot rest bend pipe is to be made up of 40 NB G.I. pipes. The Foot rest is to be made up of Aluminium casting. Extra plate is provided at bottom side of foot rest pad. All pipes is to be uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe is to be close by GI / PVC caps for user safety against entrapment. |
| 154 | The main frame of SKY WALKER is to be made in two parts, one from 80NB & 40NB Galvanized pipe & vertical pipe with 80NB pipe structure. The handle pipe is to be of 25NB GI pipes with PVC/rubber grip on top end. This handle pipes is to be hinged over 80NB main frame with the help of suitably designed heavy duty bearings assembly. Bearings used are to be of oil sealed, self-lubricating. Make of bearing shall be as per approved make list. The handle pipe is to be further extended to the rectangular tube of 50 x 50 mm on both sides with 40NB galvanized pipe links. Paired rectangular tubes with four foot rests has to be linked to main frame. Foot rest is to be made with the help of high quality Aluminium Casting material. The total structure is to be supported on Foundation stand which shall be of 80NB pipe. All pipes are to be uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe are to be closed by GI / PVC caps for user safety against entrapment. |
| 155 | Supply and installation of Children Play equipment ,Kids Platform merry go round of 1.20m dia including cross bars, 25mm NB pipes, with Base of Aluminum chequered sheet, Bearing: Triple heavy duty Bearing with water sealant (permanently Lubricated) including cost and conveyance of all materials, painting with corrossive resistance paint, labours, incidental charges etc., complte. |
| 156 | Supply and installation of Children Play equipment:Junior jungle Gym with Main Frame 1`` NB Pipe Support ¾ `` NBArea :A 4 x 5 x 6Area: B 5 x 6 x 7Area: C 6 x 7 x 8(Area: 1m*1.4m,1.2m*1.8m,Swing: 20mm NB pipe, Mainframe: 20mm NB pipes,Support: 15mm NBpipe) including cost and conveyance of all materials, painting with corrossive resistance paint, labours, incidental charges etc., complte |
| 157 | Supply and installation of Children Play equipment:Missile mast climber 8ft ht Area: 0.9m*0.9m, Height: 2.1m, Vertical support: 25mm NB pipe, Horizontal bars: 20mm NB pipe including cost and conveyance of all materials, painting with corrossive resistance paint, labours, incidental charges etc., complete |
| 158 | Supply and installation of Children Play equipment :Kids double swing 5ft ht with FRP bucket seat with Main Frame Work 2 `` NB ; Top Bar 2`` NB Pipe Bucket seat plastic; rubberized chain`` (Area 8 Feet x 4 Feet)( Area: 1.5m*1.5m, Main Frame: 25mm NB pipe, Top Bar: 35mm NB pipe, Seats: FRP seat, Bearing: Heavy duty ball bearing, Suspension: 5mm electro Galvanized chain including cost and conveyance of all materials, painting with corrossive resistance paint, labours, incidental charges etc., complete. |
| 159 | Supply and installation of Children Play equipment:Rocking boat Area: 1.2m*0.5m, Mainframe: 25mm NB pipe, Spacers: 15mm NB pipe, Seat: Moulded FRP including cost and conveyance of all materials, painting with corrossive resistance paint, labours, incidental charges etc., complete. |
| 160 | Supplying & Installation of centrifugal self priming Submersible pump with high hydraulic efficiency, chemical resistant and ultra quiet operation. Each pump integrated along with IP-55 protection- class F continuous rating. Pump shall be of one piece body of durable composite material, with SS Shaft and mechanical seal. Also have large capacity strainer with fast opening translucent lid,SucXDel-80mmX80mm Impeller : Bronze Horse power : 3 HP Phase : 3 phase 380-240V Flow rate = 32.4m³/hr @ 14m water head. Make:Kirloskar/Crompton |
| 161 | Supplying & Installation 40mm dia. Inlet Anti-Turbolent Nozzle in SS 304 , Make-himalaya |
| 162 | Providing and fixing sumbersimble insulated cable with earthing wire complete including necessary cable tray excavation & refilling wherever required.Make-Finolex/Polycab with conduit. 2 core 2.5 sqmm (from panel to Lights) |
| 163 | Providing and fixing sumbersimble insulated cable with earthing wire complete including necessary cable tray excavation & refilling wherever required.Make-Finolex/Polycab with conduit. 3 core 4 sqmm (from panel to recirculation pumps) |
| 164 | Providing and fixing and laying of Upvc 10Kg/cm2 pipes with screwed/ welded fitting i.e Tee. Elbows. Bush, MTA, FTA etc with Clamps, hangers anchor fashner, structure steel supplort as required with flow indicators, Puddle flange. Make-Supreme a) 25mm dia |
| 165 | b) 32mm dia |
| 166 | c) 40mm dia |
| 167 | Providing and fixing of ball valve(srews end) with adoptor union fitting complete in all respects. Make-Zoloto a) 25mm dia |
| 168 | b) 32mm dia |
| 169 | c) 40mm dia |
| 170 | Providing and fixing of Gun Metal non return valves of approved quality(screwed end)Make-Zoloto: 40 mm dia |
| 171 | Design, Fabrication, assembling, wring, supply, installation, testing and Commissioning of MCC Panel shall be fabricated out of 14 gauges CRCA sheet in cubicle in 3 b formation with reinforcemint of suitable size angle iron, channel `T` sectons irons |
| 172 | Installtion of Floor Mounted Type SS304 under water LED lights: IP68. 12V,18W Lights. Make: Himalaya or equivalent. |
| 173 | Supply & Installation of power supply 21A/12 V output, DC Driver Type. Make: Himalaya or equivalent. |
| 174 | Supply and Installation of Sculpture for fountain in 40mm thick Z-Black granite of minimum Height 1.5 Mtrs. with all internal arrangement for cascade flow of water over the sculpture and necessary accesories and fixtures required to install as per design and drawing. The design and shape will be as decided by customer. All inclusive excluding civil works. |
| 175 | Supply and Installation of 5m3/hr FRP sand filter with top mounted multiport valve and 1 HP pump with necessary plumbing , vaccum & inlet nozzles . Make-Emaux or equivallent. |
| 176 | Earth work in excavation by mechanical means (Hydraulic excavator) over areas (exceeding 30cm in depth, 1.5m in width as well as10sqm on plan) including getting out and disposal of excavated earth lead upto 50m and liftu pto1.5m, as directed by Engineer-in-charge.All kinds of soil |
| 177 | Filling availableexcavatedearth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm indepth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 178 | Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.All kinds of soil |
| 179 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 180 | Centering and shuttering including strutting, propping etc. and removal of form for a) Foundations, footings, bases of columns, etc. for mass concrete |
| 181 | b)Walls (anythickness) including attached pilasters, butteresses, plinth and string courses etc.. |
| 182 | c) Suspended floors, roofs, landings, balconies and access platform |
| 183 | Steel reinforcement for R.C.C.work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. |
| 184 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement- All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 185 | Brick work with common burnt clay F.P.S. (nonmodular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 186 | Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete asspecified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent |
| 187 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 188 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. |
| 189 | Providing and mixing integral crystalline admixture for waterproofing treatment to RCC structures like basement raft, retaining walls, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc. at the time of transporting of concrete into the drum of the ready-mix truck, using integral crystalline admixture @0.80% (minimum) to the weight of cement content per cubic meter of concrete) or higher as recommended by the manufacturer's specification in reinforced cement concrete at site of work. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e. by reducing permeability of concrete by more than 90%, compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure. The crystalline admixture shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the Engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. |
| 190 | System Head - Supply & installation, Jointing, testing of 2.5\\" Twin Disk Filter (Make - Jain 0r equivalent) |
| 191 | System Head - Supply & installation of 1\\" ARI Vac release valve (Make Jain or equivalent) |
| 192 | System Head - Supply & installation of Pressure Gauge (Make Jain or equivalent) |
| 193 | System Head - Supply & installation of By Pass Assembly (Make Jain or equivalent) |
| 194 | System Head - Supply & installation of 2\\" Pressure Relief Valve (Make Jain or equivalent) |
| 195 | Network - Supply & installation, Jointing, testing of 20mm UPVC Self fit pipe of 6 Kg Pressure minimum confirming to IS 13592 (Make Finolex, Supreme, Jain or equivalent) |
| 196 | Network - Supply & installation, Jointing, testing of 50mm UPVC Self fit pipe of 6 Kg Pressure minimum confirming to IS 13592 (Make Finolex, Supreme, Jain or equivalent) |
| 197 | Network - Supply & installation, Jointing, testing of 63mm UPVC Self fit pipe of 6 Kg Pressure minimum confirming to IS 13592 (Make Finolex, Supreme, Jain or equivalent) |
| 198 | Network - Supply & installation, Jointing, testing of 75mm UPVC Self fit pipe of 6 Kg Pressure minimum confirming to IS 13592 (Make Finolex, Supreme, Jain or equivalent) |
| 199 | Emitting System - Supply & installation of Professional Gear driver Rotor (Make Jain or equivalent) |
| 200 | Emitting System - Supply & installation of 3/4\\" Swing Joint Assembly Make Jain or equivalent) |
| 201 | Emitting System - Supply & installation, testing of approved make Sprinkler spout-part circle-TE2 type for shrubs (Make Jain or equivalent). |
| 202 | Emitting System - Supply, Installation & testing commissioning of approved make Impact Popup sprinkler Micro and spray jet with 360 & 180 adjustable angles (Make Jain or equivalent) |
| 203 | Emitting System - Supply & installation of 1/2\\" Swing Joint Assembly Make Jain or equivalent) |
| 204 | Emitting System - Supply & installation of 63mm Automated ball valve (Make Jain or equivalent) |
| 205 | Emitting System - Supply & installation of 6\\" Round valve box with cover (Make Jain or equivalent) |
| 206 | Emitting System - Supply & installation of Quick coupling valve with key (Make Jain or equivalent) |
| 207 | Supply and installation of all fittings and accessories like drip caps, Tees, Bends, Offsets etc. including MS angle with G.I. clamps complete required for completion of System Head, Network and Emitting System |
| 208 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C |
| 209 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 210 | Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 211 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. a) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 212 | b) 2 X 16 sq. mm + 1 X 6 sq. mm earth wire |
| 213 | Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required. A) 5/6 amps switch |
| 214 | b) 15/16 A switch |
| 215 | c) 3 pin 5/6 A socket outlet |
| 216 | d) 6 pin 15/16 A socket outlet |
| 217 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 218 | Supplying and fixing metal box of 180mm X 100mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 & 15/16 A socket outlet and 15/16 A piano type switch, connections, painting etc. as required. |
| 219 | Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 100 A, 16 KA,TPMCCB |
| 220 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way , Double door |
| 221 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door |
| 222 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. A) Single pole |
| 223 | b) Single pole and neutral |
| 224 | c) Double pole |
| 225 | Supplying and fixing TP sheet steel enclosure on surface/ recess along with 16/25/32 A 415 V \\"C\\" curve TP MCB complete with connections, testing and commissioning etc. as required. |
| 226 | Supply, fitting, wiring, testing and commissioning of 40 W 2X2 RECESS MOUNTED LED LIGHT all accessories as required. (Wipro Item Model Number DG24065) |
| 227 | Supply ,fixing , testing and commissioning of 10 W LED CEILING ROUND LIGHT all accessories as required. |
| 228 | Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. |
| 229 | Supplying, testing of Exhaust Fan with mounting frame, blades AC 230-250 complete connection and including, frame bolt/ Anchor hole fastners etc. complete finished of approved as required |
| 230 | 450 mm Dia Exhaust Fan (Make: Syska , Ventil Air - /Crompton/Almonard) |
| 231 | 375 mm Dia Exhaust Fan (Make: Syska , Ventil Air - /Crompton/Almonard) |
| 232 | S/I/T/C of Complete LED Tube fitting 20 watt ( Crompton , Havells & Phillips) |
| 233 | Supplying and laying 6 S.W.G. GI. Wire at 0.50m below ground level as strip earth electrode including thimbles, soldering etc. as required. |
| 234 | Supplying and layoing 25mm x 5mm G.I. strip at 0.5 metre below ground as strip earth. |
| 235 | Providing and fixing 25mm x 5mm copper strip in 40mm dia G.I. Pipe from earth electrode as required. |
| 236 | (xiv) (117.00+350%) Pdg. And fixing 25mm x 5 mm copper strip on surface or in recess for connections etc. as required with all labour and material. |
| 237 | Laying of underground cable 0.75 metre below ground level covered with sand and bricks including excavation and refilling of trenches.:- a) 185 sqmm to 240 sqmm 3 to 3½ Core |
| 238 | b) 50 Sq mm to 150 sqmm 2 to 4 Core |
| 239 | c) 300 sqmm to 400 sqmm 3 to 3½ Core |
| 240 | d) 2.5 Sq mm to 10 Sq mm 2 to 4 Core |
| 241 | e) 16 Sq mm to 35 sqmm 2 to 4 Core |
| 242 | Supply and erection of suitable compression type brass cable glands for underground cable:- a) 10 sqmm to 16 sqmm cable 2 to 4 Core |
| 243 | b) 25 sqmm to 50 sqmm cable 2 to 4 Core |
| 244 | c) 70 sqmm to 95 sqmm cable 3 to 3½Core |
| 245 | d) 120 sqmm to 185 sqmm cable 3 to 3½Core |
| 246 | e) 240 sqmm to cable 3 to 3½ Core |
| 247 | f) 300 sqmm to 400 sqmm cable 3 to 3½Core |
| 248 | Supply and erection of aluminium lugs heavy duty including crimping etc. upto the entire satisfaction of the Engineer-in-charge of the work. A) 10 sqmm |
| 249 | b) 16 sqmm |
| 250 | c) 25 sqmm |
| 251 | d) 35 sqmm |
| 252 | e) 70 sqmm |
| 253 | f) 120 sqmm |
| 254 | f) 185 sqmm |
| 255 | g) 240 sqmm |
| 256 | h) 300 sqmm |
| 257 | Supply, fixing, testing & commisioning 1X70W single piece deep drawn Street light fixture with silverized aluminium housing and clear PMMA diffuser. Suitable to use with Retrofit CFL lamp for 7m Pole including all required accessories as per (PHILIPS CAT NO. SRX066 1xSON-1-70W) or equivalent |
| 258 | SIT and comminssioning Outdoor ,1X18W decorative shape Bollard Luminaire with complete driver set in White or Warm White colour including all required as per accessories as per engineer incharge (PHILIPS CAT NO. HCS370 1xPL-L18W GR ) |
| 259 | SOLAR GARDEN LIGHT VEENA ENTERPRISES - PRODUCT CODE:VI-GLASS CUBEHOUSING S.S & GLASS HEIGHT : 10” DIA : 4.5” SOLAR PANEL - 4W TOP MOUNT BATTERY : LITHIUM ION BANK 8800mAh DUSK TO DAWN - ELECTRONIC CIRCUIT AUTOMATIC SWITCHING ADDITIONAL BUILT IN MANUAL SWITCH |
| 260 | SOLAR GARDEN LIGHT VEENA ENTERPRISES- PRODUCT CODE: VI - TRI CROWN HOUSING M.S. & SHEET METAL HEIGHT : 4.5 FEET DIA : 11” SOLAR PANEL - 4W TOP MOUNT BATTERY : LITHIUM ION BANK 8800 mAh DUSK TO DAWN ELECTRONIC CIRCUIT AUTOMATI SWITCHING ADDITIONAL BUILT IN MANUAL SWITCH |
| 261 | SOLAR GARDEN LIGHT VEENA ENTERPRISES - PRODUCT CODE:VI-SS CONICAL (STEPS) HOUSING P.C. & S.S HEIGHT : 11” DIA : 9” SOLAR PANEL - 4W TOP MOUNT BATTERY : LITHIUM ION BANK 8800mAh DUSK TO DAWN - ELECTRONIC CIRCUIT AUTOMATIC SWITCHING ADDITIONAL BUILT IN MANUAL SWITCH |
| 262 | Supply of flowing size of XLPE insulated PVC sheated aluminium conductor armoured cable of 1.1 KV grade on existing cable tray / surface including saddle , clamp ect. Commplete as required . a) 4CX25sqmm.(Aluminium) |
| 263 | B) 31/2CX35sqmm.(Aluminium) |
| 264 | C) 31/2CX70sqmm.(Aluminium) |
| 265 | D) 31/2CX120sqmm.(Aluminium) |
| 266 | E) 31/2CX240sqmm.(Aluminium) |
| 267 | Supply, installation , testing and commissioning of cubical type floor mounted panel suitable for 415 V , 3 Phase , 4wire 50 Hz AC supply system fabricated in compartmentalized design from CRCA sheet steel of 2mm thick for frame work and covers, 3 mm thick for gland plate i/c cleaning complete with 7 tank process for powder coating in approved shade, having 200 Amp capacity extensible type TPN Aluminium alloy bus bars of high conductivity , DMC / SMC bus bar supports with short circuit withstand capacity of 31 mva for 1 set with 2 no earth stud solid connections from main bus bar to switch gears withrequired size of AI bus bar and control wiring with 1.5sqmm PVC insulated FRLS copper conductor single core cable alleys, cable gland plates on two haff, i.c additional NO/NC contacts in all outgoing starters and provding and fixing following switch gears :-(make Indoasian) ACB 1000AMP. 4P, 50KA MANUAL DRAW-OUT TYPE (MDO) MICROPROCESSOR BASED RELEASE SETTING WITH O/L, SHORT CURCUIT PROTECTION 3 mbs Phase indication LED lamps with 2 Amp MCB test terminal block set circuit as per standard practic etc as required VAF digital electronic meter with inbuilt selector switch and class 1.0 accurancy with suitable rating CT's etc complete with wiring , connection etc Bus Bar :- 200 Amp TPN AI, extensible type Outgoings 63 Amp 4 Pole MCB - 10 KA - 6 Nos 40 Amp 4 Pole MCB - 10 KA - 7 Nos 63 Amp 2 Pole MCB - 10 KA -2 Nos 40 Amp 2 Pole MCB - 10 KA - 3 Nos All MCCB's shall be provided with rotary operated mechanism and padlocking arrangement. |
| 268 | Supply , installation , testing and commissioning of cubical type floor mounted panel suitable for 415 V , 3 phase , 4wire 50 Hz AC supply system of minimum depth 300mm fabricated in compartmentalized design from CRCA sheet steel of 3mm. Thick for frame work and covers , 3mm thick for gland plate i/c cleaning complete with 7 tank process for powder coating in approved shade , having 150 Amp capacity extensible type TPN Aluminium alloy bus bars of high conductivity , DMC / SMC bus bar supports ,with short circuit withstand capacity of 31 mva for 1 set . with 2 no. earth stud , solid connections from main bus bar to switch gears with required size of Al. bus bar making interconnection etc providing and fixing following switch gears :-(Cable entry from bottom ) make indoasian 63 Amp 4 Pole MCCB with 25 KA breaking capity - 1 set . b) 3 Nos. Phase indication LED lamps with 2 Amp back up MCB , Breaker 'ON/OFF' indicating light with 2 Amp MCB ,test terminal block set circuit as per standard practic etc as required . 00 Amp. TPN Al. extensible type ii) 20 Amp Industrial socket with 2 Pole MCB ( IP 66 )- 10 KA - 2 Nos. iii) 70 Amp TP contactor with NO /NC Contacts - 1 Nos. iv) 24 Hour Time - 1 No. |
| 269 | Supply & Installation VANASPATI ENTERPRISES of Lighting Fittings System (4x22 Ft. Pole) |
| 270 | Mobile Charging Unit: Tender Technical Specification Supply of prewired compact Mobile Charging Unit made of virgin CRCA Sheet with min. thickness 1.2mm. It shall be equipped with 2 charging Points (each point comprising of ISI marked modular 6A 1W Switch & modular 6A Sockets). Mobile Charging Unit Shall have 4nos of Modular 3Amp rated 2module Type A+C USB charging ports switched with 6A modular switch. Unit shall have ISI marked overcurrent protection device in incoming. Charging DB shall have detachable type front tray with fixing arrangements & also have detachable type 4Nos. pockets on both sides. It shall have key mounting holes to make it suitable for wall mounting. Mobile charging unit shall be treated with anticorrosive coating, finally epoxy powder coated & have IP20 degree of protection. To ensure the safety of user unit shall have proper size neutral & earth links & earthing stud on body also. Complete unit shall be manufactured at a plant certified with QMS & EMS certifications like ISO9001, ISO14001 & ISO45001 to ensure good quality product. Makes: Indoasian, Legrand, Schneider. |
| 271 | Supply of 1080p IR Outdoor camera with 1/2.8‑inch CMOS, Total sensor pixels 1920 (H) x 1080 (V); 30fps Sensitivity – Measured according to IEC 62676 Part 5 (1/30, F1.6), Color 0.06 lx, Mono 0.02 lx, With IR 30 Meter 0.0 lx, 128dB WDR, H.265; H.264; M- JPEG, Automatic Electronic Shutter (AES); Intelligent Dynamic Noise Reduction, Intelligent Defog, Rule based alarms and tracking, Line crossing, Enter / leave field, Follow route, Loitering, Idle / removed object, People counting, Crowd density estimation, 3D tracking based on Duration, Size, Aspect ratio v/h, Speed, Direction, Color, Object classes (Upright persons, Bikes, Cars, Trucks) Privacy Masking, Pixel counter, Memory card slot, IR Range 30mtr, Automatic Varifocal 3.2 to 10 mm, Alarm Input 1/1, Audio Input/output, RJ45, G.711, Audio Streaming Full-duplex / half duplex, ONVIF Profile S, G & T, IP66, IK10, PoE, CE, FCC, UL certified. SD card support up to 2TB. FTP, Dropbox and e-mail applications MAKE LIST- (Bosch / Mobotix / Geutebruck /Avigilon) |
| 272 | Supply, installation, testing and commissioning of DVR-20-CH, 400/480fps display, 400f/480ps recording, H.264, Recording @704x480 (100/120ips)/ 704x240 (200/240ips)/ 352x240 (400/480ips), 8Audio In/ 1 Out, 16 Alarm In, 4 Relay Out, Network Port available for Remote View S/W with transmission up to 120 IPS @ 352x288 PAL, along with 3 TB HDD, complete all as specified with 230VAC power supply complete in all respects as per specifications as per engineer in charge. |
| 273 | SITC of Network Video recorder to manage and control all the cameras from control room. Software shall support maximum 32 channel . Recording resolution and playback reolution should be upto 5Mp ,System should support 16 slots for HDD with 1 eSata port,RAID 0/1/5/10,should have compatibility of network redundancy,N+1 Failover, System shall support WAN connectivity.All channel synchronous Playback.Shall support GUI should support digital zoom in defined area should be UL listed Recording should be of 45 days at 2mp.HDD required.Model No TVN-2232-000 Makes :- Interlogix/CBC Ganz/Pelco |
| 274 | Supply Installation Testing & Commissioning of Managed Switch with Power on Ethernet (PoE) enabled, with 24 no's 10/100 /1000 base Tx PoE port, 1 no. Gbe Port for copper/fiber uplink |
| 275 | Supply Installation Testing & Commissioning of 9U Rack with glass front door, steel rear door, power supply, MCB, cable manager, drawer shelves and wiring channels to accommodate CCTV systems equipment and accessories as mentioned in the BOQ above Floor Standing Rack 9U (600 x 800) |
| 276 | Supply Installation Testing & Commissioning of 24 Port fully Loaded Jack/patch Panels with all required accessories and all required accessories and required CAT6E patch cords to connect to switches |
| 277 | Supply Installation Testing & Commissioning of 72 inch Full HD LED monitors |
| 278 | Supply & laying of CAT 6 cable for communication in existing 25 mm dia MS conduit |
| 279 | Supply & laying of 25 mm dia PVC conduit as required to connect and operate the system Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
