|
| 1 | Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft and loose soil complete all as specified and directed. |
| 2 | Excavating in trenches, n exc 1.5 mtr wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 mtr in depth and getting out in hard/dence type of soil all complete all as specified and directed. |
| 3 | Returning filling in including spreading, levelling, watering and well ramming in layers not exc 25cm soil complete all as specified and directed. |
| 4 | Removing surplus excavated material (soil) to distance not exc. 50 mtr and depositing where directed at a level not exc. 1.50 mtr above the starting point complete all as specified and directed. |
| 5 | Material and Labour for plain cement concrete, 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed. |
| 6 | Material and Labour for Reinforced cement concrete (design mix) in M-25 (20mm graded stone aggregates) Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. |
| 7 | Material and Labour for Reinforced cement concrete (design mix) in M-25 (20mm graded stone aggregates) Columns, pillars, piers, posts and struts complete all as specified and directed. |
| 8 | Material and Labour for Reinforced cement concrete (design mix) in M-25 (20mm graded stone aggregates) roof Beams, cantilevers, bressummers, lintels over 1.5mtr span complete all as specified and directed. |
| 9 | Material and Labour for Reinforced cement concrete (design mix) in M-25 (20mm graded stone aggregates) in roof Slab supported in walls beams and columns in roof ,Landing, balconies, deck slabs and in shelves and similar work complete all as specified and directed. |
| 10 | Material and Labour for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surfaces complete all as specified and directed. |
| 11 | Material and Labour for Formwork to sides of pillars, posts, struts, piers, columns and stanchions Square, Circular rectangular on plan or polygonal complete all as specified and directed. |
| 12 | Material and Labour for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.on flat rough surface complete all as specified and directed. |
| 13 | Material and Labour for Formwork to soffits of suspedded slabs such as roof slabs, floor slabs landings and similar work ,vertical or to batter for rough finished flat surfaces of concrete complete all as specified and directed. |
| 14 | Material and Labour for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished even and smooth (without using extra lime or cement) complete all as specified and directed. |
| 15 | Material and Labour for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth (without using extra cement) complete all as specified and directed. |
| 16 | Material and Labour for rendering 10mm thick in cement mortar 1:3 on ceiling surface, finished even and smooth without using extra cement complete all as specified and directed. |
| 17 | Material and Labour for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all complete all as specified and directed. |
| 18 | Material and Labour for mild steel TMT bars 6 mm to 8 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete complete all as specified and directed. |
| 19 | Material and Labour for Precast cement concrete block masonry type C1 1:3:6 (20mm graded stone aggregate) with solid blocks, exc. 10 cm in width and, setting in cement mortar 1:6 complete all as Specified and directed. |
| 20 | Material and Labour for PCC 1:2:4 type B-0 (using 12.50 mm graded stone aggregate), as in lintels upto 1.5 mtr clear span, cills, steps,seismic and other similar bands, plinth course, string courses, lacinng courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed. |
| 21 | Material and Labour for Moorum filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed. |
| 22 | Material and Labour for Hardcore of broken stone or boulder gauge exc 63mm but n. exc 100mm, deposited , spread and levelled in layers n.exec 15 cm thick, watered and rolled/rammed to a tue surface complete all as specified and directed. |
| 23 | Material and Labour for 100 mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) in sub base of floor is to be rough finished complete all as specified and directed. |
| 24 | Material and Labour for 75 mm thick, PCC (1:3:6), Type C-1, using 20 mm graded stone aggregate as in Plinth protection etc surface finished even and fair without using extra cement including necessary form work if required, provision of vertical joints at 2 mtr centre to centre complete all as specified and directed by Engr -in- charge. |
| 25 | Material and Labour for Non Skid Ceramic tiles, Coloured, of size exceeding 0.06 Sqm and not exceeding 0.11 Sqm,7 to 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:6 complete all as specified and directed. |
| 26 | Material and Labour for Glazed Ceramic Coloured tiles of size 300mmX600mmX7mm as in Vertical Surfaces such as Skirting, dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over backing coat of 10mm thick in cement mortar 1:4 complete all as specified and directed. |
| 27 | Supply and Fixing aluminium louvered ventilators of section size 100mmx25mmx1.50mm including frosted glass 4mm thick fixed in half portion & adjustable type louvers in another half and stainless steel wire mesh 0.36mm nominal dia & 1.40 mm avg width of aparture fixed type on outside frame etc. including taking down existing steel ventilator incl taking down old ventilator complete all as specified and directed by Engr-in-Charge. |
| 28 | Supply and Fixing aluminium powder coated window sliding type (3 track) with frame size 100x35x1.20mm and shutter 39.40mmx17.70mmx1.20mm with two glass shutter and one stainless steel wire mesh shutter including necessary jointing cleats, glazing clips, rubber packing powder coated aluminium snap beading screws with and includings 4mm thick plain float glass and 0.36mm dia SS wire mesh, and avg width of aparture 1.40 mm fittings etc, and necessary locking arrangements and including making good the jambs and painting with matching type and shade including taking down existing steel window complete all as specified and directed by Engr-in-Charge. |
| 29 | Material and Labour for Providing and fixing 30mm thick FACTORY MADE MOULDED DOOR SHUTTER - WOOD FREE consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 25mm x 25mm for stiles, top and bottom rails. M.S. frame shall have a coat of steel primers. The inner panel shall consist of 25m thick EPS of Density 23 Kg / Cbm. bonded with 2mm thick termite proof, water proof and fire resistant moulded PVC sheet manufactured by an ISO-9001-2015 certified company, with 2,4,6 raised panel design in different plain and / or prelam colours after routing the Moulded design on one side & 2mm plain and / or prelam PVC sheet on other side of EPS. The edge of panel to be sealed with lipping of 15 mm wide PVC sheet baton (made by sticking 2mm rigid foam PVC sheets of 5mm (+0.25) thickness using PVC solvent cement) and stile sides 25mm (5mm x 5Nos) thick and 30mm width PVC sheet fitted along M.S tube for hardware provision & for lock 25mm thick (5mm x 5Nos). PVC sheet of size 150mm x 200mm fixed with inner side of EPS Panel etc complete all as per specification & drawing and as directed by Engineer-in-Charge. |
| 30 | Supply and Fixing Aluminium anodised barrel tower Bolt of size 150 mm size of extruded section complete all as specified and directed. |
| 31 | Supply and Fixing Aluminium cast type anodised Handle, size 150mm long complete all as specified and directed. |
| 32 | Supply and Fixing 100 mm size, heavy weight Butt Hinges, cold rolled, mild steel including fixtures complete all as specified and directed. |
| 33 | Supply and Fixing Aluminum anodised sliding door bolts, bearing ISI mark, 300mm long with hasp and staple(bolt type) and fixing clips of sheets ,cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed. |
| 34 | Material and Labour for applying two coats of cement base paint on plastered surfaces of walls including preparation of new surface complete all as specified and directed. |
| 35 | Material and Labour for applying three coats of white wash to newly plastered surface of ceiling including preparation complete all as specified and directed. |
| 36 | Material and Labour for applying two coats of oil bound distemper over a coat of primer to newly plastered surface including preparation of new plastered surfaces to wall complete all as specified and directed. |
| 37 | Supply and Fixing 20mm bore GI tubes, medium grade, galvanised , with all fitting & fixed complete to walls & ceilings or laid in floors complete all as specified and directed. |
| 38 | Supply and Fixing 15 mm bore tubes, medium grade, galvanised, with all fitting & fixed complete to walls & ceiling or laid in floors, all as specified and directed [The rate is deemed to be included for concealing of GI tubes wherever required and directed]. |
| 39 | Supply and Fixing for looking mirror of any size n.exc 2.00 sqm & 5mm thick mirror of selected quality glass,,mounted on 6mm thick commercial plywood and bevelled edge fixed on wall with six nos. stainless steel studs decorative type complete all as specified and directed by the Engineer-in-Charge (make Modi Guard/Saint Gobin.) |
| 40 | Supply and Fixing fancy type two way Bib cock 15mm dia , fancy type, chromium plated with capstan or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and suitable for 15 bore of pipe fixed all complete all as specified and directed (Make :Jaquar/Hindware/Cera/Prayag ). |
| 41 | Supply and Fixing for fancy type CP brass angular stop cock 15 mm dia complete all as specified and directed. (Make :Jaquar/Hindware/Cera/Prayag). |
| 42 | Supply and Fixing PVC connection of 600 mm length, suitable for 15 mm bore pipe with PTMT nuts, complete all as specified and directed. |
| 43 | Supply and Fixing fancy type heavy duty health faucet chromium plated (ABS Body) with 8mm Dia, 1 Meter Long Flexible Tube & Wall Hook fixing to 15 mm bore of pipe complete all as specified and directed.(Make :Jaquar/Hindware/Cera/Prayag). |
| 44 | Supply and Fixing CP grating ring or frame square or round 100 mm size complete all as specified and directed. |
| 45 | Supply and Fixing Vitreous china wash hand basin (550mmX400mm) white with pedestal , flat back excluding taps but including brackets & CP waste coupling 32mm, LDPE waste pipe 32 mm upto floor complete all as specifed and directed. |
| 46 | Supply and Fixing Vitreous china Urinal half stall type white, with grating and union for discharge pipe fixed including all reqd necessary fittings as instructions of manufacturers, bottle trap , fixing to existing wall complete all as specified and directed.Make : Jaquar/ Cera/Hindware/ Parryware or equivalent. |
| 47 | Supply and Fixing PVC (SWR) pipes 75mm dia ,single socketed in any length with rubber ring joints laid in trenches or floor & wall complete all as specified and directed. |
| 48 | Supply and Fixing PVC (SWR) pipes 110 mm dia ,single socketed in any length with rubber ring joints fixed and laid in trenches or floor/ceiling and wall complete all as specified and directed. |
| 49 | Supply and Fixing 15 mm dia Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed. |
| 50 | Supply and Fixing PVC (SWR) bends any radius, 75mm dia pipe complete all as specified and directed. |
| 51 | Supply and Fixing PVC (SWR) branch piece 110 mm bore, single Y equal or unequal complete all as specified and directed. |
| 52 | Supply and Fixing PVC (SWR) junction 110mm bore single T equal or unequal complete all as specified and directed. |
| 53 | Supply and Fixing in Powder coated Aluminium grill of approved pattern using channel of required size, screwed to windows & ventilators with self tapping screws complete all as specified and directed. |
| 54 | Cutting chases, pinning in concrete block walls, making good to facing where required and pointing in cement mortar (1:3) and making good , cutting n.exc 10cm girth complete all as specified and directed. |
| 55 | Supply and Fixing for towel ring chromium plated brass fancy type complete all as specified and directed by the Engineer-in-Charge. (Make :Jaquar/Hindware/Cera/Prayag). |
| 56 | Supply and fix for sheet glass shelf assembly consisting of 5.5 mm thick sheet glass 12 cm wide with CP bracket guard and railing 60 cm long complete all as specified and directed. |
| 57 | Supply and Fixing Rotational moulded Polythene [HDPE] Water Tanks, Cylindrical & Vertical Type 500 Liters Capacity triple layered 'ISI' marked, hoisted and fixed in position including provision of 40mm/25mm dia spouts for connecting inlet, outlet, over flow and washout pipes complete all as specified and directed. |
| 58 | Supply and Fixing 20 mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 455 gms) complete all as specified and directed. |
| 59 | Material and Labour for applying roof treatment as under :-(i) Providing 10 mm thick (average) rendering in cement mortar 1:3 mixed with WPC as per manufacturer's instruction (to be measured separately as supply only) for levelling to a true surface and to receive new roof treatment complete.(ii) Providing a coat of bitumen primer @ 0.40 Litre/Sqm over plastered surfaces of roof including parapet surfaces.(iii) Providing one layer of APP based polymeric membrane of approved manufacturer, 3mm thick, weight not less than 3.50 Kgs per Sqm, reinforced with polyester non woven fabric (weighing not less than 150 Gms/Sqm). Polymeric membrane shall be taken to a height 60cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. (Note:(a) Laying of APP based polymeric membrane shall be done by torch application method or as per manufacturar's instruction. (b) Side overlaps shall be minimum 75mm and end laps shall be minimum 100mm and sealing all overlaps and joints as manufacturer's instructions. (c) The make of polymeric membrane shall be as per PS Specification of CA.(iv) Applying two coats of bituminous aluminium paint on top of APP membrane. |
| 60 | Supply and Fixing (any type & size of door) powder coated aluminium anodised door with frame and shutter and glazing with and including 5 mm thick tinted glass and 12 mm thick powder coated prelaminated particle board exterior grade in panels, rubber gasket, aluminium glazing clips, mortice lock, Aluminium stopper cleat, hydraulic double action floor door spring, iron mongary etc. section of aluminium door including powder coating of any colour (min thickness of powder coating 50 micron) shall be of following sizes:-Frame : 100 x 44 x 1.80 mm thick with rawal plugMiddle lock rail: 100 x 44 x 1.80 mm thickBottom rail : 100 x 44 x 1.80 mm thickTop rail / Style: 46 x 44 x 1.80 mm thickGlazing beading: 0.70 mm thickAluminium handle 'D' type: 150 mm Aluminium tower bolt 9.9 mm dia shoot 200 mm long Mortice lock – 100 mm 4 lever,Aluminium stopper cleat Note :- (i) Making good of wall surface with matching to existing surface complete all complete all as specified and directed.(ii) Making good floor surface after fixed hydraulic double action floor door spring with matching to existing surface complete all as specified and directed. |
| 61 | Excavation in trenches not exceeding 1.50 mtr wide and 1.50 mtr depth for foundation, etc., for Shaft wells, Manholes etc not exceeding 10sqm on plan and not exceeding 1.50 mtr in depth and getting out in soft / loose soil complete all as specified and directed. |
| 62 | Material and Labour for PCC M-7.5 grade nominal mix using 40 mm graded stone aggregate as in concrete bed to drain pipes including packing under and haunching against sides of pipes with concrete after they are laid and bedded dia of pipe 150 mm complete all as specified and directed. |
| 63 | Material and Labour for 150 mm dia RCC drain pipes class NP2 laid in trenches and jointed with in cement mortar complete all as specified and directed. |
| 64 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing coat) complete all as specified and directed. |
| 65 | Material and Labour for 25 mm thick PCC 1 :2 : 4 type B0 ( Using 12.5 mm graded stone aggregate ) as in base of floors complete all as specified and directed by Engineer-in-Charge. |
| 66 | Material and Labour for Non Skid Ceramic tiles, Coloured, of size exceeding 0.18 Sqm and not exceeding 0.38 Sqm,7 to 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 complete all as specified and directed. |
| 67 | Material and Labour for applying two coats of white wash to old plastered surface of ceiling including preparation complete all as specified and directed. |
| 68 | Taking up or down 15 mm bore steel tubing and connections including disconnection of fittings and cleaning for refixing where required, complete all as specified and directed. |
| 69 | Ditto-all as above Item No. 68 but 20 mm dia pipe etc. |
| 70 | Supply and Fixing Buttoned looking mirror of any size n.exc 2.00 sqm & 5mm thick mirror of selected quality glass,,mounted on 6mm thick commercial plywood and bevelled edge fixed on wall with six nos. stainless steel studs decorative type complete all as specified and directed by the Engineer-in-Charge (make Modi Guard/Saint Gobin.) |
| 71 | Supply and Fixing two way Bib cock 15mm dia , golden finish, fancy type, chromium plated with capstan or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and suitable for 15 bore of pipe fixed all complete all as specified and directed (Make :Jaquar/Hindware/Cera/Prayag). |
| 72 | Supply and Fixing in repairs chromium plated golden finish single lever basin mixer without popup waste system with 450mm long braided hoses complete all as specified and directed by the Engineer-in-Charge. Make : Jaquar/ Cera/Hindware/ Parryware . |
| 73 | Supply and Fixing for fancy type , golden finish CP brass angular stop cock 15 mm dia complete all as specified and directed. (Make :Jaquar/Hindware/Cera/Prayag). |
| 74 | Supply and Fixing fancy type heavy duty health faucet chromium plated, golden finish (ABS Body) with 8mm Dia, 1 Meter Long Flexible Tube & Wall Hook fixing to 15 mm bore of pipe complete all as specified and directed.(Make :Jaquar/Hindware/Cera/Prayag). |
| 75 | Material and Labour for 75 mm dia cast iron floors trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1(20mm graded stone aggregate), complete all as specified and directed. |
| 76 | Supply and Fixing wash down water closet EWC vitrious china white in colour one piece (incl flush cistern , seat cover) with all fitting Supply and Fixing complete and fixing with outlet pipe complete all as specified and directed by the Engineer-in-Charge. Make : Jaquar/ Cera/Hindware/ Parryware. |
| 77 | Supply and Fixing for table top vitreous china wash hand basin white size 460mmx 342mm/ 560mmx450mm or above miniumum depth 155 mm or above under counter oval type including bottel trap, coupling making good complete all as specified and directed.and all connecting accessories, etc (first quality) complete all as specified and directed by Engineer-in-Charge.Make : Jaquar/ Cera/Hindware/ Parryware. |
| 78 | Supply and Fixing Vitreous china Urinal half install type white, with grating and union for discharge pipe fixed icluding all reqd necessary fittings as per instructions of manufacturers, bottal trap , fixing to existing wall complete all as specified and directed. Make : Jaquar/ Cera/Hindware/ Parryware. |
| 79 | Supply and Fixing in repairs 20mm dia bore Gun metal, globe or gate valves with Iron wheel head, screwed both ends for Iron pipes and fixed complete all as specified and directed. |
| 80 | Supply and Fixing in repairs Powder coated Aluminium grill of approved pattern using channel of required size, screwed to windows & ventilators with self tapping screws complete all as specified and directed. |
| 81 | Supply and Fixing Paper holder with flap gaurd CP brass, golden finish (Make : CERA/Jaquar/Somany) complete fixing to wall with fittings complete all as specified and directed. |
| 82 | Supply and Fixing Towel Rack 600mm long CP Brass, golden finish (Make : CERA/Jaquar/Somany) complete fixing to wall with fittings complete all as specified and directed. |
| 83 | Material and Labour for Dismantling of old stone slab of any description complete all as specified and directed. |
| 84 | Material and Labour for 20mm thick Granite work (table rubbed and polished) in steps, jambs, cills, WHB platforms,counter tops and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over and including 20mm Screed bed in CM 1:4, all complete all as specified and directed. |
| 85 | Supply and Fixing in repairs for towel ring chromium plated brass fancy type, golden finish complete all as specified and directed by the Engineer-in-Charge. (Make :Jaquar/Hindware/Cera/Prayag). |
| 86 | Supply and Fixing in repairs for sheet glass shelf assembly consisting of 5.5 mm thick sheet glass 12 cm wide with CP bracket guard and railing 60 cm long complete all as specified and directed. |
| 87 | Material and Labour for 15 mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces including finishing the surface with a thin layer of sagol complete all as specified and directed. |
| 88 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed. |
| 89 | Supply and Fixing coloured UPVC door having thickness 2.3 mm with frame size 67mm x 64mm and shutter size 67mm x 110mm and glazing with 5 mm thick tinted / frosted glass or ACP sheet 4mm thick in panels, uPVC extruded glazing beads of appropriate dimension,EPDM gasket, zinc alloy hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, necessary stainless steel screws etc including taking down old door with chowkhat complete all as specified and directed by Engr- in- charge Note :- (i) Making good of wall surface with matching to existing surface complete all as specified and directed. |
| 90 | Supply and Fixing switch piano type 250 volts single pole one way 6 Amp complete all as specified and directed by Engr in Charge |
| 91 | Material and Labour for Cutting PP-R pipes any dia and reducing to required length before laying and for insertion of new Tees, Branches, JP Joints with nut & bolts etc. complete all as specified and directed. |
| 92 | Supply & laying pipe galvanised medium grade of 25 mm dia including all fitting ( such as bends, elbows, tees required for reduce size as per site requirment, short pieces, connectors, back-nuts, diminishing pieces, caps, plugs and unions, etc) and fixing complete with clips, wall hooks, wooden plug, or laying in trenches or fixed to wall /floor/roof including cutting screwing etc, complete all as specified and directed. |
| 93 | Supply and fix PPR Gate Valves (Brass Insert) of 25 mm bore complete all as specified and directed. |
| 94 | Supplying, laying, jointing, commissioning and testing XLPE insulated screened PVC bedded, armoured, heavy duty underground electric cable with stranded aluminium conductor 1100 volts grade confirming to IS-7098 (Part-I-1988) laid in trenches/ducts/wall / floor / pipes/ poles including cable glands and aluminium lugs of appropriate size, pvc sleeve etc complete all as specified and directed by Enginner in -Charge of size 10 Sqmm 2 core . Make :- Havells / Gloster / Finolex / Polycab (Cable to be laid from nearest LT Panel to TPN DB/Metering panel) |
| 95 | Material and Labour for riddled earth cushioning to under ground cable in trenches / existing cable trenches/ducts in layers of 8 cm deep before laying the cable and 15 cm deep after laying and stretching the cable complete all as specified and directed by Engr in charge. Note:- Measurement shall be taken after gentling punning. |
| 96 | Material and Labour for Brick \\" class B \\"protection for under ground cable complete all as specified and directed . |
| 97 | Supply and Fixing light grade GI pipe of size 40 mm dia conforming to IS 1239 (Part-1): 2004 laid in trenchs or under floors or fixed on pole for cable protection complete all as specified and directed by Engr - in - Charge. |
| 98 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc complete all as specified and directed. |
| 99 | Material and Labour for point wiring complete with 1.5 Sqmm single core FRLS PVC insulated unsheathed cable 1100 V grade multi stranded copper conductor drawn through non metallic rigid PVC conduit and accessories concealed in walls including 1.5 Sqmm dia multistranded copper cable as earth continuity conductor connected to common earth dolly, including pressed steel terminal boxes to provision of Modular switches to house switch/regulators etc including Modular Plate and Covers for one fan/light /bell point controlled by one switch/bell push complete all as specified and directed. Note: Two runs of 1.5 sq mm(Phase and Neutral)and one runs of 1.5 sqmm(Earth) cable along with conduit shall be measured as one length. |
| 100 | All as per item No 99 above for one 3 pin 5 Amps socket on same board controll with other switches on same board complete all as specified and directed. |
| 101 | All as per Item No 99 .here-in- before but with 2.5 Sqmm PVC insulated multistranded copper conductor with 2.5 sqmm cable as earth continuity conductor for Power Socket/Geysers on independent board complete all as specified and directed. |
| 102 | Supply and fix modular socket 6A 2/3 pin combined 2 module complete all as specified and directed. |
| 103 | Supply and fix modular switch 1 way 6A 1 module complete all as specified and directed. |
| 104 | Supply and Fixing PVC ceiling rose surface type three terminals type complete all as specified and directed by Engr in Charge. |
| 105 | Supply and fixing in repair LED lights fitting 1x 20W, 220V,AC, decorative box type with driver, holder incl LED tube light connecting up with flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. |
| 106 | Supply and fixing in repair LED Light fitting mirror type with high output diffuser 2 feet , 1 X 10 watt 220 V AC decorative type with driver holder and LED lamp, Alluminium housing, including connecting up with flexible copper conductor cable of suitable size complete all as specified and directed. |
| 107 | Material and Labour for submain wiring in PVC conduit with two runs of 4 sq mm and one runs of 4 sqmm for earth continuity 1100 v grade PVC insulated unsheathed FRLS grade copper conductor cable single core multistranded ISI marked (IS 694) drawn through and including 25 mm dia PVC rigid connduit medium grade ISI marked (IS 9537 Part III) includung accessories such as bends, supports etc all complete all as specified and directed. Note: Two runs of 4 sq mm (Phase &Neutral) and one runs of 4 sqmm (Earth) cable along with conduit of size 25mm shall be measured as one length. |
| 108 | Taking down old unservicable Exhaust fan and depositing it to MES store and Supply & fix Exhaust fan steel body AC single phase , 230 volts of size 300 mm sweep with blades and frame and louvers complete all as specified and directed.Note : (i) To be Fixed in Existing Toilet window (ii) The rates are inclusive of any civil work required to fix the exhaust fan. |
| 109 | Supply & fix in repair water heater of capacity 25 ltr. storage type with copper inner tank, complete along with heating element, thermostat, indicator lamp, hot and cold water flexible stainless steel water pipe connection including necessary gate valve/stop valve, fastners, complete all as specified and directed by Eng-in-charge. |
| 110 | Supply and fix single pole and neutral enclosure with a two pin and earth plug and socket complete with 20 Amp DP MCB complete all as specified and directed ( For Gyeser/AC ) |
| 111 | Supply and Fixing distribution board factory made SPN 4 way in, 240 Volt, Double door metal type suitable for fixing MCBs as out going and including SPN MCB 32 Amps as main incoming complete all as specified and directed. Make; Legrand / L&T / ABB. |
| 112 | Supply and Fixing MCB SPN 32 Amps 'C' series 10 KA with two position DIN Rail clamp. Make; Legrand / L&T /ABB complete all as specified and directed. |
| 113 | Supply and Fixing MCB SP 5 to 30 Amps 'B' series 10 KA with two position DIN Rail clamp. Make; Legrand / L&T / ABB complete all as specified and directed. Please Enable Macros to View BoQ information |
