|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m All kinds of soil. |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 3 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 4 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar |
| 5 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 6 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm. |
| 7 | Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge. |
| 8 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 9 | Brick work with clay fly ash F.P.S. (non modular) brick of class designation 3.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand). |
| 10 | Brick work with clay fly ash F.P.S. (non modular) brick of class designation 3.5 in superstructure above plinth level up to floor one level in: Cement mortar 1:6 (1 cement : 6 coarse sand). |
| 11 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 12 | Reinforced cement concrete work in beams, suspended foors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 13 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars |
| 14 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 15 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. |
| 16 | 12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand). |
| 17 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 18 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bar etc.including priming coat with approved steel primer all complete.Fixed to steel window by welding. |
| 19 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 20 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 21 | Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm) |
| 22 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks). |
| 23 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick. |
| 24 | Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts. |
| 25 | Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform. |
| 26 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections ……………...all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :Powder coated aluminium (minimum thickness of powder coating 50 micron). |
| 27 | Providing and fixing ACP in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With ACP panes of 4.0 mm thickness ( For DooR ). |
| 28 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness ( For Window ) |
| 29 | Providing and Fixing ( Thickness : 16-18 Gauge,) Heavy duty Domal Three track Sliding Windows including 5 mm thick toughned Glass of high quality and mosquito net all complete set of approved brand such as jindal or equivalent as per instructions of Engg. inchage. |
| 30 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 31 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content.With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre |
| 32 | Finishing walls with Acrylic Smooth exterior paint of required shade: Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface. |
| 33 | Finishing walls with water proofing cement paint of required shade :Old work (one or more coats @ 2.20 kg/10 sqm) complete. |
| 34 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete size of tile 600 X 600 mm. |
| 35 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 36 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 37 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :125 mm. |
| 38 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : (copper oxidized as per IS: 1378) 300x16 mm |
| 39 | Providing and fixing bright finished brass door latch with necessary screws etc. complete : 300x16x5 mm. |
| 40 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 300x10 mm. |
| 41 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 42 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work. |
| 43 | Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid . |
| 44 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. |
| 45 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively. |
| 46 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 47 | Providing and fixing white vitreous china wash basin including makin gall connections but excluding the cost of fittings : Flat back wash basin of size 630x450 mm |
| 48 | Providing and fixing PTMT bib cock of approved quality and colour.15mm nominal bore, 86 mm long, weighing not less than 88 gms. |
| 49 | Providing and fixing PTMT stop cock of approved quality and colour.15 mm nominal bore, 86 mm long, weighing not less than 88 gms. |
| 50 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter |
| 51 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 75 mm diameter |
| 52 | Providing and fixing 100 mm sand cast Iron grating for gully trap. |
| 53 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore |
| 54 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 55 | Constructing soak pit 1.20x1.20x1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. |
| 56 | Providing and fixing uplasticised PVC connection pipe with brass unions : 30 cm length |
| 57 | White washing with lime to give an even shade : Old work (two or more coats). |
| 58 | Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, filling the joints with fine sand etc. allcomplete as per the direction of Engineer-incharge. |
| 59 | Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50mm including strengthening with 2mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge.Made of G.I. wire of dia 4mm |
| 60 | Providing and fixing concertina coil fencing with punched tapeconcertina coil 600 mm dia 10 metre openable length (total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Springcore (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocksshall be paid separately) |
| 61 | Providing and fixing 2 SEATER ARC SWING Specification Main structurePipe- structure made of MS Pipe OF 60 od and 25 od pipe OF 3 to 4 mm thickness Seats- structure made of Bucket seat and FRP pata OF 3 TO 4 mm Thickness. Paint – Powder Coated (Thickness 90 micron) The aforementioned item should be having a minimum of 01 years of warranaty and should be implemented all complete as per the direction of engineer in charge, |
| 62 | Providing and fixing Straight FRP Slide (8 Feet) Specification Main structurePipe- structure made of ms. Pipe OF 48 od, 32 od and 25 od pipe and box pipe are ½” x 2”pipe. Slide- structure made of FRP Paint – Powder Coated (Thickness 90 micron) The aforementioned item should be having a minimum of 01 years of warranaty and should be implemented all complete as per the direction of engineer in charge, |
| 63 | Providing and fixing WAVE Slide (8 Feet) Specification Main structurePipe- structure made of ms. Pipe OF 48 od, 32 od and 25 od pipe and box pipe are ½” x 2”pipe. Slide- structure made of FRP Paint – Powder Coated (Thickness 90 micron) The aforementioned item should be having a minimum of 01 years of warranaty and should be implemented all complete as per the direction of engineer in charge, |
| 64 | Providing and fixing DOUBLE SEE SAW/DOUBLE BAR FOUR SEATER SEE SAW Main structurePipe- structure made of M.S. Pipe OF 60 OD, 48od and 42od pipe OF 2 to 3 mm thickness Seats - structure made of LLDP Handrails - structure made of M.S. 1” Pipe Round Pipe. Paint – POWDER COATING The aforementioned item should be having a minimum of 01 years of warranaty and should be implemented all complete as per the direction of engineer in charge, |
| 65 | Providing and fixing DOME CLIMBER Main structureMain Pipe- structure made of M.S. Pipe OF 50 OD OF 2 TO 3 mm thickness Stairs- structure made of heavy duty M.S. Pipe of 32 OD of 2 to 3 mm thickness.Handrails - structure made of M.S. 1” Round Pipe. Paint – POWDER COATING. The aforementioned item should be having a minimum of 01 years of warranaty and should be implemented all complete as per the direction of engineer in charge, |
| 66 | Providing and fixing Rainbow Climer Main structure Main Pipe- structure made of M.S. Pipe OF 50 OD OF 2 TO 3 mm thicknessStairs- structure made of heavy duty M.S. Pipe of 32 OD of 2 to 3 mm thickness.Handrails - structure made of M.S. 1” Round Pipe.Paint – POWDER COATING . The aforementioned item should be having a minimum of 01 years of warranaty and should be implemented all complete as per the direction of engineer in charge, |
| 67 | Providing and fixing FABRO NET CLIMBERMain structureMain Pipe- structure made of M.S. Pipe OF 50 OD OF 2 TO 3 mm thickness Climbing Sheet- structure made of FRP(4 TO 5 MM THICKNESS) Rope – Made of Nylon of 16 mm Thickness Handrails - structure made of M.S. 1” Round Pipe. Paint – POWDER COATING. The aforementioned item should be having a minimum of 01 years of warranaty and should be implemented all complete as per the direction of engineer in charge, |
| 68 | Providing and fixing S CLIMBER Main structureMain Pipe- structure made of M.S. Pipe OF 50 OD OF 2 TO 3 mm thickness Stairs- structure made of heavy duty M.S. Pipe of 32 OD of 2 to 3 mm thickness. Handrails - structure made of M.S. 1” Round Pipe. Paint – POWDER COATING.The aforementioned item should be having a minimum of 01 years of warranaty and should be implemented all complete as per the direction of engineer in charge, |
| 69 | Providing and fixing at site inclusive of all the charges of material transportation and placing/fixing, with premium finishing of equipments all complete as per the direction of engineer in charge- Chest Press And Shoulder Press Specification Main structure- Pipe- structure made of GI Pipe OF 4” OD , 42 OD AND 32 OD OF 3 to 4 mm thickness Arm – structure made of GI Pipe 32 OD 4 mm thickness. Bearing – Ball bearing (6205) Bearing Caps - Made up of HDPE Material. Seats- structure made of M.S. SEAT OF 2 mm Thickness. Pole Caps – Made up of HDPE Material. Paint – Powder Coated (Thickness 90 micron). |
| 70 | Providing and fixing at site inclusive of all the charges of material transportation and placing/fixing, with premium finishing of equipments all complete as per the direction of engineer in charge Leg Extension Specification Main structure- Pipe- structure made of GI Pipe OF 60od 42 OD AND 32 OD OF 3 to 4 mm thickness Bearing – Ball bearing (6205) Bearing Caps - Made up of HDPE Material. Seats- structure made of GI SHEET OF 2 mm Thickness. Pole Caps – Made up of HDPE Material. Paint – Powder Coated (Thickness 90 micron). |
| 71 | Providing and fixing at site inclusive of all the charges of material transportation and placing/fixing, with premium finishing of equipments all complete as per the direction of engineer in charge Leg Press Double Specification Main structure- Pipe- structure made of GI Pipe OF 4” OD and 42 OD OF 3 to 4 mm thickness Bearing – Ball bearing (6205) Bearing Caps - Made up of HDPE Material. Seats- structure made of M.S. SEAT OF 2 mm Thickness. Pole Caps – Made up of HDPE Material. Paint – Powder Coated (Thickness 90 micron. |
| 72 | Providing and fixing at site inclusive of all the charges of material transportation and placing/fixing, with premium finishing of equipments all complete as per the direction of engineer in charge Double Shoulder Wheel Specification Main structure- Pipe- structure made of GI Pipe OF 4” OD AND 32 OD OF 3 to 4 mm thickness Pole Caps – Made up of HDPE Material. Paint – Powder Coated (Thickness 90 micron) |
| 73 | Providing and fixing at site inclusive of all the charges of material transportation and placing/fixing, with premium finishing of equipments all complete as per the direction of engineer in charge Double Standing And Seating Twister Specification Main structure- Pipe- structure made of GI Pipe OF 4” OD, 42 OD AND 32 OD pipe OF 3 to 4 mm thickness Twister Plate - structure made of M.S. SEAT OF 5 mm Thickness with LLDPE PLATE/SHEET. Seats- structure made of GI SHEET OF 2 mm Thickness. Pole Caps – Made up of HDPE Material. Paint – Powder Coated (Thickness 90 micron) |
| 74 | Providing and fixing at site inclusive of all the charges of material transportation and placing/fixing, with premium finishing of equipments all complete as per the direction of engineer in charge PARALLEL BAR Specification Main structure- Pipe- structure made of GI Pipe OF 3” and 32 OD OF 3 to 4 mm thickness Paint – Powder Coated (Thickness 90 micron). |
| 75 | Providing and fixing at site inclusive of all the charges of material transportation and placing/fixing, with premium finishing of equipments all complete as per the direction of engineer in charge Air Walker Double Specification Main structure- Pipe- structure made of GI Pipe OF 4” od and 42 OD OF 3 to 4 mm thickness Arm – structure made of GI Pipe 32 OD 4 mm thickness. Bearing – Ball bearing (6205) Foot Rest - structure made of GI SHEET OF 2 mm Thickness. Bearing Caps - Made up of HDPE Material. Pole Caps – Made up of HDPE Material. Paint – Powder Coated (Thickness 90 micron) |
| 76 | Providing and fixing at site inclusive of all the charges of material transportation and placing/fixing, with premium finishing of equipments all complete as per the direction of engineer in charge Double Surfboard Specification Main structure- Pipe- structure made of GI Pipe OF 4” OD and 42 OD OF 3 to 4 mm thickness Arm – structure made of GI Pipe 32 OD 4 mm thickness. Bearing – Ball bearing (6205) Foot Rest - structure made of GI SHEET OF 2 mm Thickness. Bearing Caps - Made up of HDPE Material. Pole Caps – Made up of HDPE Material. Paint – Powder Coated (Thickness 90 micro. |
| 77 | 6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand) |
| 78 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. One coat sqm |
| 79 | Total impact of GST for the purpose of CTC Please Enable Macros to View BoQ information |
