|
| 1 | Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : DSR 2.10 |
| 2 | All kinds of soil DSR 2.10.1 |
| 3 | Pipes, cables etc. exceeding 80 mm dia. DSR 2.10.1.1 |
| 4 | Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia DSR 2.10.1.2 |
| 5 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : DSR 6.4 |
| 6 | Cement mortar 1:4 (1 cement : 4 coarse sand) DSR 6.4.1 |
| 7 | 12 mm cement plaster of mix : DSR 13.4 |
| 8 | 1:4 (1 cement: 4 coarse sand) DSR 13.4.1 |
| 9 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : DSR 17.3 |
| 10 | W.C. pan with ISI marked white solid plastic seat and lid DSR 17.3.1 |
| 11 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: DSR 17.7 |
| 12 | White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps DSR 17.7.3 |
| 13 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. DSR 17.16A |
| 14 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. DSR 17.28 |
| 15 | Flexible Pipe DSR 17.28.2 |
| 16 | 32 mm dia DSR 17.28.2.1. |
| 17 | Providing and fixing soil, waste and vent pipes : DSR 17.35 |
| 18 | 100 mm dia |
| 19 | Centrifugal Sand cast iron S&S pipe as per iS : 3989 DSR 17.35.1.2 |
| 20 | 75 mm dia DSR 17.35.2 |
| 21 | Centrifugal Sand cast iron S&S pipe as per iS : 3989 DSR 17.35.2.2 |
| 22 | Providing and fixing heel rest sanitary bend DSR No. 17.40 |
| 23 | 100 mm dia as per DSR No. 17.40.1.2 |
| 24 | Providing and fixing collar DSR 17.57 |
| 25 | 100mm diaSand cast iron S&S as per IS: 3989 DSR 17.57.1.2 |
| 26 | 75mm diaSand cast iron S&S as per IS: 3989 DSR 17.57.2.2 |
| 27 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : DSR 17.60 |
| 28 | 100 mm inlet and 75 mm outlet DSR 17.60.2 |
| 29 | Sand cast iron S&S as per IS : 3989 DSR 17.60.2.1 |
| 30 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.: DSR 18.10 |
| 31 | 15 mm dia. nominal bore DSR 18.10.1 |
| 32 | 20 mm dia. nominal bore DSR 18.10.2 |
| 33 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : |
| 34 | size 20mm i/d DSR 18.17.1A |
| 35 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : DSR 18.18 |
| 36 | 20 mm dia. nominal bore DSR 18.18.2 |
| 37 | Providing and fixing uplasticised PVC connection pipe with brass unions : DSR 18.21 |
| 38 | 45 cm length DSR 18.21.1 |
| 39 | 15 mm nominal bore DSR 18.21.2.1 |
| 40 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) DSR 18.46 |
| 41 | 15 mm nominal bore DSR 18.46.1 |
| 42 | 20 mm nominal bore DSR 18.46.2 |
| 43 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank DSR 18.48 |
| 44 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : DSR 18.49 |
| 45 | 15 mm nominal bore DSR 18.49.1 |
| 46 | Providing and fixing C.P. brass long body bib cock of approved quality |
| 47 | 15 mm nominal bore DSR 18.51.1 |
| 48 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. DSR 18.52 |
| 49 | 15 mm nominal bore. DSR 18.52.1 |
| 50 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 DSR 18.53 |
| 51 | 15 mm nominal bore DSR 18.53.1 |
| 52 | Providing and fixing of Extension nippple upto 1-1/2\\" length DSR 18.53A |
| 53 | Cutting holes up to 30x30 cm in walls including making good the same: DSR 18.76 |
| 54 | With common burnt clay F.P.S. (non modular) bricks DSR 18.76.1 |
| 55 | Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. DSR 18.77 |
| 56 | Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc. DSR 18.78 |
| 57 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than .70 kg as per standard design: DSR 19.4 |
| 58 | 100 x 100 mm size P-type DSR 19.4.1 |
| 59 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 DSR 19.4.1.1 |
| 60 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: |
| 61 | Inside dimensions 455x610 mm and 45 cm deep for single pipe line : DSR : 19.30.1.1 |
| 62 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 DSR:19.30.1.1 |
| 63 | Construction of Curb consisting of cement concrete 1:2:4 including cost of C.P. hinged grating and cost of sand bajri etc. |
| 64 | Providing drip seal joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter : |
| 65 | 100 mm |
| 66 | 75 mm |
| 67 | Providing and fixing of CP Brass/SS/ABS overhead shower with swiveling Joint , 125mm dia (min) with C.P Brass/ S.S Shower Arm and flange to the satsifaction of EIC of approved make ESSCO Model No. 536A & 542A or equialent Model of CERA /Kerovit/ Jal |
| 68 | Providing and fixing of C.P. cup heavy duty make of approved make |
| 69 | Prov. & fixing of looking mirror of size 450x600mm made with 5mm thick (minimum) superior quality glass including cost of hard board, PVC beading and C.P. Screw etc. to satisfaction of EIC of approved make |
| 70 | Providing and fixing of CP Brass/SS Towel Rail 600mm of with screws etc. to the satsifaction of EIC of approved make Jal Model No. 36520 Warna or equialent Model of CERA /Kerovit/ ESSCO |
| 71 | Providing and fixing of CP Brass/SS/ABS Soap Tray made of Plastic including glass bowl of approved make Jal Model No. 36540 or equialent Model of CERA /Kerovit/ ESSCO |
| 72 | Providing and fixing of CP Brass/SS Towel Ring with screws etc. to the satsifaction of EIC of approved make Jal Model No. 36524 Warna or equialent Model of CERA /Kerovit/ ESSCO |
| 73 | Providing and fixing of C.P. Brass Nossel Tap for Gardening Please Enable Macros to View BoQ information |
