|
| 1 | Taking down shutters of any description exc. 1.00 Sqm and n exc. 2.00 Sqm each, complete all as specified. |
| 2 | Taking down Chowkats or Frame (without taking off shutter from the frame) n exc. 1.50 Sqm, complete all as specified. |
| 3 | Taking down Chowkats or Frame (without taking off shutter from the frame) exc. 1.50 Sqm but n exc 4.00 Sqm each, complete all as specified. |
| 4 | Repair to existing aluminium door by replacing of rubber beading, aluminium beading, screws, replacement of glass and other accessories like door closer, hinges as reqd and making door functional incl taking down if reqd and refix after reassembling door complete all as specified and directed.Note- door closer, floor spring, glasspanes will be measured separately. |
| 5 | Repair to existing sliding/openable aluminium window by replacing of rubber beading, aluminium beading, of same colour, if any, screws, replacement of glass and other accessories like aluminium snap beading, rubber gasket glazing clips, hinges as reqd and making window functional incl taking down if reqd and refi after reassembling window complete all as specified and directed.Note- Glass panes will be measured separately. |
| 6 | M&L for Mild Steel 150 mm ordinary rat tail rod pattern spring including roller and roller plate complete with welding etc and making good the disturbed portion complete all as specified. |
| 7 | M&L in repair Mild Steel 150 mm ordinary rat tail rod pattern spring including roller and roller plate complete with welding etc and making good the disturbed portion complete all as specified. |
| 8 | S&F Floor door stopper of 140mm aluminium alloy body and tongue, anodised, with hard drawn steel spring, complete all as specified. |
| 9 | S&F 40 mm thick flush shutter solid core construction, with block board core and plywood face panels commercial type on both side complete all as specified. |
| 10 | S&F 35mm thick 2nd class hard wood Glazed and Skelton Shutter open rebated and prepared to receive glass gauze etc (without shas bar) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of numbers of shutter as specified in SSR Pt I Section 8, clause 8.24 (a) complete all as specified and as directed. |
| 11 | M &L for preparation of new wooden surfaces of any description over 10 cm width or girth and applying 02 coats of synthetic enemel paint over incl one coat of primer complete all as specified. |
| 12 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified. |
| 13 | S&F Factory made Solid Panel PVC Door Shutter 30 mm thick consisting of frame made out of MS tubes for Top & bottom nails MS framed shall be covered with neat moulded plain coloured PVC 'C' channel having PVC sheet ship if 20 mm width stuck inside with solvant cement for style and plain colour PVC shutters for top rail lock rail and bottom rail on edges side & gap insert for top rail bottom rail panelling of plain colour PVC sheet truck and nail with suitable PVC sheet bedding and jointed to shutter with solvent gear supply and fixing in the frame at site complete all as specified. |
| 14 | M&L for Factory made Steel Window 1.25mm thick box type (primer coated) ERW hollow P section of size 60mm x 25mm including grill using 10Sqmm bar double rebated both gauge and glass shutter comprised gauged glazed Skelton shutter of ERW section 50mm x 20mm and 1.0mm thick with two openable leafs having two Nos sash bar of T Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T- Section of size 60mm x 25mm and 1.25mm thick including cutting holes and good dismantled portion in PCC (1:2:4) type B-1 four Nos for each window including following fittings welded to frame shutter complete all as specified and as directed:- (a) Hold Fast, 150mm long of Flat Iron 12mm x 3mm made to shape 04 Nos per window . (b) Handle of Z-Section 20mm x 25mm, 100mm Long 01 No per Leaf . (c) MS Tower bolt 150mm long - 02No per leaf . (d) Z-section 20mm x 25mm, 100mm Long Stopper 1 No per Leaf .(e) Cleat 55mm Long of Hollow Square 15mm x 20mm x 63mm welded to Hinge 01 No per Leaf .(f) MS Pintal hinges of size 75mm x 12mm 02 Nos per Leaf including Stainless Steel Wire Cloth, 0.25mm to 0.36mm nominal dia of wire & average width of aperture 1.40mm to 02mm & fixed with aluminium wire staples and glass pane 3mm thick fixed with MS pin and oil putty including two coats of synthetic enamel paint complete and incl taking down the existing old windows. |
| 15 | S&F factory made mild steel ventilators box type with upper top hung shutters and bottom fixed type shutters including pintol hinges, steel peg stay and one shop coat of red oxide primer incl taking down old, complete all specified. Note :- (i) The ventilator shall be fabricated as per Drg No CEUZ/TD/1302/2009 Sheet 1/3 to 3/3. (ii) Glazing, wire gauge shall be measured and paid separately. |
| 16 | S&F 100mm long Butt Hinges extruded aluminium alloy with Galvanised mild steel hinge pin, anodised and fixed complete all as specified and as directed. |
| 17 | S&F in repairs 150mm long Extruded aluminium alloy Handles, fabricated type, anodisedcomplete all as specified and as directed. |
| 18 | S&F 150mm long Extruded aluminium alloy Handles, fabricated type, anodised complete all as specified and as directed. |
| 19 | S&F 150mm long extruded Brass handles, cast type,polished bright complete all as specified and as directed. |
| 20 | S&F in repairs 200mm long Aluminium anodised, barrel Tower Bolts of extruded section and fixed complete all as specified and as directed. |
| 21 | S&F 200mm long Aluminium anodised, barrel Tower Bolts of extruded section and fixed complete all as specified and as directed. |
| 22 | S&F 300mm long Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and as directed. |
| 23 | S&F in repairs 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed. |
| 24 | S&F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed. |
| 25 | S&F aluminium (diecast body) door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and as directed. |
| 26 | S&F for galvanised stainless steel wire cloth, 0.56 mm nominal dia wire and average width of aperture 1.18 mm and fixed with tinned tacks or stainless steel wire staple complete all as specified. |
| 27 | S&F in repair galvanised stainless steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or stainless steel wire staple complete all as specified. |
| 28 | S&F aluminum powder coated of any colour (thickness of powder coating not less than 50 micron), in frame for doors, window, ventilators, partition wall etc, with one or more rabates, shutters, inlcuding joining cleat for fixing etc. complete all as specified and as directed. |
| 29 | S&F powder coated aluminium doors shutters, (thickness of powder coating not less than 50 micron) aluminium section weighing exc 0.55 Kg/m including necessary joining cleats, glazing clips rubber neoprene packing, handle 2 Nos in each door, fixed with floor hinges/ spring (measured separately), 4 lever brass mortice lock vertical type (1 No ), powder coated snap beading, screws etc complete all as specified and directed. |
| 30 | S&F anodized, powder coated aluminium window and ventilator shutters hung type/sliding, (thickness of powder coating not less than 50 micron) aluminium section weighing exc 0.55 Kg/m including necessary joining cleats, glazing clips rubber neoprene packing, handle in each shutter, including locking arragement anodised aluminium snap beading screws etc complete all as specified and directed. |
| 31 | S & F in repairs Sheet Glass, 4.0mm thick glazing with Beads or Oil Putty, not exc. 0.5 Sqm in Each Pane, complete all as specified and as directed. (Note:- At any height) |
| 32 | All as per serial item No 42 above but 4.00 mm thick Figured glass, pinhead type in squares n exc 0.5 sqm each pane complete all as specified and as directed. |
| 33 | S&F 4.8 mm thick sheet tinted sheet glass fixed to doors and window all as specified and directed. |
| 34 | M&L for double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, govering pivot made of brass, other parts made of mild steel heavy duty and fixed. |
| 35 | S & F mortice lock brass 4 levers vertical type, size 100mm complete all as specified and as directed. |
| 36 | S & F in repairs mortice lock brass 4 levers vertical type, size 100mm complete all as specified and as directed. |
| 37 | S & F in repairs aluminium (die cast) body door closer hydraulically regulated designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed. |
| 38 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for, complete all as specified and directed. |
| 39 | Demolition of stone slabs and tiles of any description or thickness in floors,walls, aprons etc |
| 40 | M & L for Cement concrete type B-0, 1:2:4 (12.5 mm graded aggregate) 25mm thickness as in floor for laying tiles brushing with neat cement slurry @ 3.00 Kg/Sqm complete all as specified and as directed. |
| 41 | M&L for chequred cement concrete tiles of size 30cm X 30 cm X 25mm thick, laid over 15mm thick screed bed or bedding layer in cement mortar 1:6 with grey cement and pigments, set, jointed and pointed in neat cement slurry in floors complete all as specified and directed. |
| 42 | M&L for Non-skid Coloured Ceramic Tiles (Square/rectangular) area of each tile exceeding 0.11 sqm but nexc 0.18 sqm, 7-8mm thick in floors etc set & jointed in neat cement slurry & pointed in white or coloured cement to match including screed bedding layer of 15 mm thick in CM 1:6, complete all as specified and as directed. |
| 43 | M&L for Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bedding layer of 15 mm thick in CM 1:6, complete all as specified and as directed. |
| 44 | M&L for Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in dado/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface including 10 mm thick in CM 1:3, complete all as specified and as directed. |
| 45 | M & L for Glazed coloured ceramic tiles in vertical surface 450x300x7 mm/350x 250x7mm / 450x350x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10mm thk screed bed in CM 1:3, complete all as specified and as directed. |
| 46 | Dismantling structural steel work including doors, gates of opening area n.exc 30.00 sqm each but excluding framed truss etc. complete all as specified and as directed. |
| 47 | S & F steel rolling shutters 1.25mm thk of laths push pull or manual type of opening area n.exc 30.00 sqm each ,without ball bearing,as specified including top cover, anchoring rod, hasp and staple and , erected in position as indicated complete all as specifeid and as directed. |
| 48 | S & F steel rolling shutters 1.25mm thk of laths gear operated type of opening area n.exc 30.00 sqm each with bevel gear box and crank handle as specified including top cover, anchoring rod, hasp and staple and , erected in position as indicated complete all as specifeid and as directed. |
| 49 | Repairs to existing steel rolling shutters without ball bearing by taking down top cover, anchoring rod,spring etc and providing new springs and achoring rod,replacing the worn out strips of shutters and welding of handle,hasp stapel and other broken articles etc, greasing the spring,guide eail,shaft etc and making functional and errecting in position, including refixing of top cover/hood etc., opening n exc 10 Sqm each finally painting with two coat of synthetic enamel paint complete all as spefied. |
| 50 | Demolition of brick work or stone masonry built in cement mortar including all quoines arches, pillar etc but excluding ashlar facing , dressed stone work and precast concrete articles complete all as specified. |
| 51 | M&L brick work with sub class B bricks straight or curved on plan exc 6m redius in CM 1:6 complete all as specified and as directed. |
| 52 | Taking down cement plaster of any description on brick, concrete or stone walls or ceiling including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off complete all as specified and as directed.(Note: Height of the work upto 20.00 m) |
| 53 | M&L for rendering 15 mm thick CM 1:6 on fair faces of brickwork or concrete surfaces finished even & smooth w/o using extra cement complete all as specified and as directed.(Note: Height of the work upto 20.00 m) |
| 54 | M & L for Rendering 15mm thick in cement mortar 1:4 on other than fair faces of Brick walls or on concrete surfaces plastered surfaces finished even and smooth without using extra cement complete all as specified and as directed. (Note: Height of the work upto 20.00 m) |
| 55 | M&L Rendering 5mm thick on fair faces of brick work or concrete surfaces in CM (1:3) in ceiling complete all as specified and as directed. |
| 56 | M&L for two coats of Cement base paint on new plaster surfaces as per the existing surfaces including preparation of surfaces complete all as specified and as directed.(Note : Pattern of cement base paints to be match with existing surfaces surrounding areas.) |
| 57 | M & L for preparing New Surfaces of Walls and applying two Oil Bond distemper including 2 mm thick wall care putty complete all as specified and as directed. |
| 58 | M & L for two coats of white wash on newly plaster surfaces of ceiling incl preparation of surfaces complete all as specified and as directed. |
| 59 | Taking up or down 15mm bore of CPVC tubing with connections for cleaning for refixing or removing to store/yard complete all as specified . |
| 60 | Supplying and laying of CPVC pipes SDR 11 of 16mm outer diameter of pipe & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) all as specified. |
| 61 | S&F in repairs vitreous china wash down Water Closet white squatting pan Orissa pattern size 580x440mm with integral foot rest incl making necessary connections to soil pipes and flushing cistern complete all as specified and as directed. |
| 62 | S & F in repair Vitreous china wash down water closet Pan (pedestal Pattern) white colour (excluding fixing bolt, flushing cistern and flush pipe) size 580 x 440mm with integral foot rest connecting flushing cistern and flush pipe complete all as specified and as directed. |
| 63 | S&F in repair seat and cover for pedestal pan white / black closed pattern with flat bottom and cover and MS chromium plated aluminium hinge devic, complete all as specified and as directed. |
| 64 | S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed. |
| 65 | S&F in repair Vitreous china Wash Hand Basin size 550x400mm (flat back or angle back type) including 32mm dia brass chromium plated waste fitting a pair if cast iron bracket duly painted/erecting stand including cutting and pinning in ends making good disturbed surfaces in CM 1:3 including taking down unserviceable wash hand basin and connected items of any description, complete all as specified. |
| 66 | M&L for PVC Flushing Cistern 10 litre capacity low level valve less, symphonic action type white with inlet, ball valve, flaoat and handle including 32mm dia PVC Flush pipe a pair of cast iron brackets duly painted/erecting stand including cutting and pinning in ends, making good disturgbed surfaces in cement mortar 1:3 including taking down unserviceable flushing cistern complete all as specified and directed. |
| 67 | S&F in repair angular Stop/Angle valve fancy type chromium plated,screwed down, high pressure with crutch or butterfly handle 15mm bore, complete all as specified and as directed. |
| 68 | S&F in repair Brass chromium plated WHB center hole single lever mixer for mixing hot & cold Water screwed down for iron pipe 15mm bore complete all as specified and as directed. |
| 69 | S&F in repair, Bib taps cast copper alloy 15mm bore, fancy type Chromium Plated , screwed down high pressure with crutch or butterfly handle, screwdd both ends for iron pipe or for unions, complete all as specified and as directed. |
| 70 | S&F in repairs Pillar cock 15mm bore fancy type chromium plated, screwed down high pressure with or without lettered HOT or COLD with long screwed and fly-nuts screwed for iron pipe or brass ferrule complete all as specified and as directed. |
| 71 | S&F in repair Looking mirror 600 x 450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers all as specified and directed. |
| 72 | S&F in repair CP Grating doom 100mm dia complete all as specified and directed. |
| 73 | M&L for PVC Conncetions 15mm size with PTMT Nuts of length 450mm and fixed including taking down unserviceable PVC Connections, complete all as specified and as directed. |
| 74 | S&F in repairs High density polyethylene (HDPE) pipes of 32mm bore of pressure rating 6 kgf/sq. cm complete all as specified and as directed. |
| 75 | S&F in repairs Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) |
| 76 | S&F in repairs Vitreous China half stall urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs withand including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) |
| 77 | S&F in repairs Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed in 15 mm pipe complete. |
| 78 | Demolition of stone slabs and tiles of any description or thickness in floors,aprons laid dry |
| 79 | M & L 18-20 mm thick granite(of any type) work (table rubbed and polished) in steps, jambs,pillars,window cills,cooking platforms and the like in CM 1:4 incl pointing in white cement(1:2) using marble dust with admixture of pigment to match with shade of granite |
| 80 | M&L machine cut Kota stone slab flooring 18-20mm thick, laid over and incl 15mm thick cement screed /rendering in CM 1:6 ,laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl cutting, rubbing, grinding and polshing to achive mirror finish complete all as spd. |
| 81 | M&L machine cut Kota stone slab in riser of steps,skirting,dado and pillar, 15mm thick, mixed with pigment to match the shade of the slab incl 10mm thick cement screed /rendering in CM 1:4 incl cutting, rubbing, grinding and polshing to achive mirror finish complete all as spd. |
| 82 | Providing edge moulding to 18-20mm thick granite stone any description of counters vanities etc including machine polishing to edge to give high gloss finish etc all as specified and as directed . |
| 83 | M&L for dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as speified and directed. |
| 84 | S&F plain tile false ceiling on 24mm 'T' framework of module 600mm x 600mm at a height 10 to 20 mtr from average ground level. Panel shall be manufactured of size 575mm x 575mm made out of 0.50mm TCT thick GI (galvanised steel) powder coated of not less than 55-60 micron in white colour. Grid system for fixing ceiling tiles shall be comprises of Tees. The 24mm main tee runners of size 3000mm shall be suspended at an interval of 1200mm c/c. The 24mm cross runners of size 600mm shall be suspended at 600mm c/c and further supported with 24mm cross tee at 600mm c/c with interlocking arrangement form grid of 600mm x 600mm. The main tee shall be supported by means of 4mm GI rod from slab/roof with the help of anchor. The suspension shall be provided at 1200mm c/c complete all as specified and as directed. Make - OCULUS Building products Pvt Ltd or any equivalent. |
| 85 | Providing & fixing in repairs false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles with semi perforated 12 mm thick nicro tegular edged GRG false ceing tiles of size 595 x 595 mm of approved texture, designand patterns having moisture content less than 2%, humidity resistance of 99%,NRCO 0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476(part 4)-1970 and light reflectance of 85%(minimum) to be laid in true horizontal level suspended on iterlocking metal T-Grid of hot dippped galvanised iron section of 0.33 mm thick(galvanised @120 grams per Sqm including both sides) comprising of main T runners of size 15 x 32 mm of length 3000 mm, cross T of size 15 x 32 mm of length 600 mm to form grid module of size 600x 600 mm,suspended from ceiling using galvanised mild steel items(galvanised @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners,6 mm dia fully threaded hangar rod upto 1000 mm length and L-shape level adjuster of size 85 x 25 x 2mm. Galvanised iron perimeter wall angle of size 24 x 24 x 0.40 mm of length 3000 mm to be fixed on periphery wall/partition with the help of plastic rawl plugs at 450 mm centre to centre and 40 mm long dry wall wood screws/ suspended from MS frame work complete all as specified. |
| 86 | S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing. |
| 87 | S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing. |
| 88 | Dismantling boarding, any description, fixed in any position with nails complete all as specified and as directed. |
| 89 | S&F wooden flooring with 21mm thick teak wood planks (i.e. African imported) grade AB of size 450mm to 1500mm length and 50mm to 90mm wide fixed over treated pine runner of size 70mm x 45mm laid over existing subbase of floor @350mm c/c in bothways. The wooden runner to be treated with anti termite chemical. The wooden runners to be fixed with existingnsubbase of floor by suitable fastener at the interval of 500mm c/c. The planks to be joined to each other with tongue and groove method and fixed on 10mm thick rubber air cushioned pads stappled through the two wings @ 350mm c/c in bothways. The top surface of wooden flooring finally finished with PU polishing water based polyurethane lacquer complete all as specified and as directed. |
| 90 | Supply and fixing 21mm thick teak wood planks (i.e. African imported) grade AB of size 450 to 1500mm length and 50 to 90mm wide fixed to wall with necessary screws as in skirting including finish the top surface with PU polishing water based polyurethane lacquer complete all as specified and as directed. |
| 91 | Dismantling of AC (Corrugated, Semi Corrugated etc)/CGI or any type of sheets in roof covering complete.(Note: Work will be carried out up to a height of 22 m from GL). |
| 92 | S&F plain, Aluminium sheeting, Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (length and girth as fixed) complete all as specified and as directed.(Note: Work will be carried out up to a height of 22 m from GL). |
| 93 | Pre-painted galvalume corrugated aluminum zinc coating GI based steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified(Note: Work will be carried out up to a height of 22 m from GL). |
| 94 | M&L for anti-termite treatment of soil under existing floors using emulsion @1 litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar (1:2) to match the existing floors complete all as specified and as directed. |
| 95 | M&L for anti-termite treatment for points of contract of wood work by chemcial emulsion (in oil kerosene based solution) @0.5 litre per hole drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and as directed. |
| 96 | Dismantling wrought iron or mild steel work of any description not otherwise provided for any height |
| 97 | Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion from Concrete and making good disturbed ground complete. |
| 98 | S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified.(Fe 410 -W (Gde- E- 250) quality- AFe) |
| 99 | S&F Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated)(Fe 410 -W (Gde- E- 250) quality- AFe) complete all as specified and directed. |
| 100 | S&F Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment.(Fe 410 -W (Gde- E- 250) quality- AFe) complete all as specified and directed. |
| 101 | M&L for Preparation of new steel and iron surfaces of any description over 10 CM width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed. |
| 102 | Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and naturalfibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws and including making the surface good after the installation of frame all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S Sscrews shall be paid separately) |
| 103 | Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 100 mm/65 x 125mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 104 | S&F in repairs galvanised. 2 strand, steel Barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails , including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and as directed. |
| 105 | Dismantling fencing wire mesh, any type complete all as specified and as directed. |
| 106 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and as directed. |
| 107 | Supply only Chain link MS galvanisd fencing, any size or type complete all as specified and as directed. |
| 108 | Excavation in post holes( or similar holes) each n exc 0.5 cum , getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm in any type of soil,complete all as specified and as directed. |
| 109 | M&L for PCC 1:3:6 Type C-2 (using 40mm graded Agg) as in foundations, filling and mass concrete, complete all as specified and as directed. |
| 110 | Mild steel work for Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes,notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc. and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed. |
| 111 | M&L for Mild steel round bars 10mm dia and over , cut to length, bent to shape reqd, including cranking, bending for tieing of chain link fencing of Gd.I, IS-432 (Part-I), complete all as specified and as directed. |
| 112 | Demolition of cement concrete (unreinforced) as in ground floor & paving n exc 15cm thick below or above ground level complete all as specified and as directed. |
| 113 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid dry or laid dry and pointed in ant type of mortar complete all as specified and as directed by Engineer-in-Charge. |
| 114 | M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade withgrey cement and pigment complete all as specified and as directed |
| 115 | M&L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade with topping of cement mixed with grey cement and pigment complete all as specified and as directed |
| 116 | M&L for sand cushioning 50mm thick under floor or in foundation including watering and consolidation, complete all as specified and as directed. |
| 117 | M&L for PCC 1:4:8 type D-2 75 mm thick (using 40mm graded aggregate) as in sub base layer, complete all as specified and as directed. |
| 118 | Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete. complete all as specified and as directed |
| 119 | Providing and fixing factory made uPVG white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steelFrame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile tobe inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware[Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mmnominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories and making surface good after the installation of window. Net Opening will be measured lor payment purpose.)(A) Area not exceeding 2.00 sqm each |
| 120 | S&F of aluminium deco grill outside window, complete in all respect, including frame, grill members, fixing accessories, labour and all incidental works complete all as specified and as directed. Please Enable Macros to View BoQ information |
