|
| 1 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and as directed. |
| 2 | M & L Glazed ceramic coloured tiles of 600 x 300 x 7mm thick or 450 x350mm size 7-8mm thick in vertical surfacethick set and jointed in neat cement slurry and pointed in white or colour cement to match over including screeding 10 mm thick in CM 1:4 on wall complete in all respect as specified. Colour and pattern approved by EIC).Make :- Somany or equivalent in Kajaria/Johnsion |
| 3 | M&L for Vitrified Ceramic coloured tiles 10 mm thick (square/rectengular) polished, size of each tiles is 600x600mm as in floors, over 15 mm thick screed bed in CM 1:4 and joint shall be kept as 3mm filled with epoxy. to attain the best result 3mm thick tile spacers to be used, Masking tape shall be put before putting the eposy grout & the grout shall be throughly cleaned immendiatly. complete all as specified and directed. |
| 4 | M&L for joint free non skid, ceramic “coloured” tiles 7 to 8 mm thick area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm thick, in floor, shelves etc, set and jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles over and including 15mm thick screed bed or bedding layer in cement mortar 1:6, complete of item all as directed. |
| 5 | M&L for joint free non skid, ceramic “coloured” tiles 7 to 8 mm thick area of each tile exceeding 0.18 Sqm but not exceeding 0.36 Sqm thick, in floor, shelves etc, set and jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles over and including 15mm thick screed bed or bedding layer in cement mortar 1:6, complete of item all as directed. |
| 6 | M&L for heavy duty coloured (approved colour) fully vitrified paving tiles of size exc 0.09 but not exc 0.16 sqm ,12mm thick, set and jointed in neat cement slurry and pointed in coloured or white cement to match the shade of tiles over and including 15 mm thick screed in cement mortar 1:6 complete all as specified and directed. |
| 7 | Dismantling of Machine pressed precast conctete interlocking paver block any shape, size and thickness for refixing of good paver blocks complete all as specified and directed. |
| 8 | Demolition of cement concrete (unreinforced) in ground floor and in paving not exceeding 15 cm thickness (below or above ground level) and disposal of all bldg Materials to out side MOD land as per NGT guide line complete all as specified & directed. |
| 9 | M&L for 75mm PCC type D -2 (1:4:8) using 40 mm graded crushed stone aggregate as in Sub base complete all as specified and directed. |
| 10 | M&L for cement concrete type B1 1:2:4 using 20mm graded stone aggregate as in coping, kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates complete all as specified and directed. |
| 11 | M&L for 80mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 30mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer for cushioning through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 12 | M&L for 60 mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 25mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer for cushioning through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 13 | M&L 75 mm thick PCC 1:3:6, type C-2, using (40mm graded stone aggregate) as in plinth protection and finished the surface even and smooth without using extra cement, laid in panel, including filling the joints with sand mixed with bitumen in 1:1 ratio complete all as specified and as directed. |
| 14 | Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc. |
| 15 | M & L for Granite (of any type) 18-20mm work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platform sand like in over and incl 15 mm thick screed beeding layer in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite all as specified by Engr-in-charge |
| 16 | Dismantling of water tanks of capacity exc 2000 ltrs and not exc 5000 ltrs complete all as specified and directed |
| 17 | Dismantling of water tanks of capacity exc 1000 ltrs and not exc 2000 ltrs complete all as specified and directed |
| 18 | Dismantling of water tanks of capacity exc 500 ltrs and not exc 1000 ltrs complete all as specified and directed |
| 19 | Dismantling of water tanks of capacity exc 250 ltrs and not exc 500 ltrs complete all as specified and directed |
| 20 | S&F rotational moulded,multilayer HDPE water storage tank of 5000 ltrs capacity(Cylindrical vertical with closed top) ISI marked fixed in position on existing places complete all as specified including 02 Nos 20mm dia full threaded GI tank niple, 20 mm dia PTMT float valve epoxy coated Aluminium rod with high density plastic float ball( of minium weight 210 gms ) and refixing of inlet, outlet & overflow pipe etc, complete all as specified and as directed. |
| 21 | S&F rotational moulded,multilayer HDPE water storage tank of 2000 ltrs capacity(Cylindrical vertical with closed top) ISI marked fixed in position on existing places complete all as specified including 02 Nos 20mm dia full threaded GI tank niple, 20 mm dia PTMT float valve epoxy coated Aluminium rod with high density plastic float ball( of minium weight 210 gms) and refixing of inlet, outlet & overflow pipe etc, complete all as specified and as directed. |
| 22 | S&F rotational moulded,multilayer HDPE water storage tank of 1000 ltrs capacity(Cylindrical vertical with closed top) ISI marked fixed in position on existing places complete all as specified including 02 Nos 20mm dia full threaded GI tank niple, 20 mm dia PTMT float valve epoxy coated Aluminium rod with high density plastic float ball( of minium weight 210 gms ) and refixing of inlet, outlet & overflow pipe etc, complete all as specified and as directed. |
| 23 | S&F rotational moulded,multilayer HDPE water storage tank of 500 ltrs capacity(Cylindrical vertical with closed top) ISI marked fixed in position on existing places complete all as specified including 02 Nos 20mm dia full threaded GI tank niple, 20 mm dia PTMT float valve epoxy coated Aluminium rod with high density plastic float ball( of minium weight 210 gms) and refixing of inlet, outlet & overflow pipe etc, complete all as specified and as directed. |
| 24 | S&F in repair 20 mm bore dia Gun metal gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed. |
| 25 | Taking up or down 15mm bore, steel tubing and connection including cleaning for refixing or removal from site. |
| 26 | Taking up or down 20mm bore, steel tubing and connection including cleaning for refixing or removal from site. |
| 27 | S&F 20 mm OD CPVC pipes SDR 11 with concealed & Brass fittings ( incl Brass Elbow, Brass Elbow (3/4 X ½) mm,Brass Tee, Male Brass Threaded Adaptor (MTA/ MBTA),Female Brass Threaded Adaptor (FTA/ FBTA, Brass Union,) for all points on walls/ ceiling or laying in floors complete all as specified and directed. |
| 28 | S&F 25 mm OD CPVC pipes SDR 11 and concealed & Plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors complete all as specified and directed. |
| 29 | Dismantling of CI pipes/PVC pipe & fitting of any description & position up to 110 mm dia complete all as specified & directed. |
| 30 | S&F 75 mm bore PVC (SWR) pipe single socket in any length with rubber ring joints fixed to walls. |
| 31 | S&F 100 mm bore PVC (SWR) pipe single socket in any length with rubber ring joints fixed to walls. |
| 32 | S&F PVC (SWR) Bend 75mm dia. |
| 33 | S&F PVC (SWR) Bend 110 mm dia. |
| 34 | M&L mild steel work as in bands, straps, supports or stays for rain water, ventilating pipes including bolts, if required, hooks (stay) heavy for large gates, hooks and pintle hinges, large hasp and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans and similar articles conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 35 | S & F in repair plastic water closet seat cover white, closed pattern with flat bottom and mild steel chromium plated hinging device complete all as directed and as specified. |
| 36 | S & F in repairs Vitreous china floor/wall mounted WC ( Cascade) one piece type (off white) complete including connecetion in drain etc incl water closet seat cover , flushing cistern, with P or S trap with all fitting and fixture complete all as specified and as directed. (Make : Jaquar or equivalent as per approved make list). |
| 37 | S&F in repair Vitreous China squatting pan 'Orissa' pattern size 580 x 440 mm white, with integral foot rests with connection to trap , and to flushing pipe antisyphonage pipe including trap set in and including concrete etc complete including making good to floor all as specified and dirtected by Engr-in-Charge . |
| 38 | S&F as in repair Wash down water closet (Pedestal pattern) using vitreous china with ‘P’ or ‘S” trap, front or back inlet and foot rests, any pattern (excluding flushing cistern ), complete with & including Flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern, Plastic water closet seat, white, recessed bottom pattern including seat cover and mild steel chromium plated or aluminised hinging device |
| 39 | S&F as in repair Vitreous China urinals, half stall type complete including providing and fixing plugs,waste coupling, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe using vitreous China Urinal, Half stall type, white with & including waste pipe etc complete all as specified. |
| 40 | S&F in repair 15 mm CP Brass Urinal spreader with Hex heavy quality for urinal complete all as specified and directed. |
| 41 | S & F in repairs for Brass chromium plated bottle traps 32mm for wash basins & urinals with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed with concealed PVC pipe of 32mm/ 40 mmm dia. |
| 42 | S & F in repairs 32 mm dia waste Pipe, for WHB & urinals complete all as specified and directed. |
| 43 | S&F in repairs basin/ urinal partition of size 900x450 mm curved shaped with frosted glass 8-10mm thick with chrome finished and all necessory fittings complete all as specified and as directed. |
| 44 | S & F 10 ltrs capacity PVC valveless syphonic action type flushing cistern low level white with inlet ball valve, float, chain and pull and brackets etc complete. (Make: Hindware /Parryware /Cera 0r equvalent) |
| 45 | S & F repair white wash basin with full pedestal of size 560 x415 x 820 mm complete all as specified and directed .Make prayag/cera/parryware/Hindware |
| 46 | S&F as in repair oval type wash hand basin China of 560x410mm size, fixed in stone/granite complete. |
| 47 | S & F as in repair 32 mm dia Waste fittings, brass, chromium plated for wash hand basins etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed. |
| 48 | S & F as in repairs PVC connections 15 mm size with PTMT nuts both ends including PVC washers of length 450mm |
| 49 | S&F as in repairs Pillar taps with swan neck, cast copper alloy, with capstan heads, chromium plated, Fency type, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed Make:- Jaquar or equivalent |
| 50 | S&F in repairs 5 mm thick bevelled edge looking mirror 600 x 450 mm size of selected quality glass with aluminium frame of channel alround mounted on 4 mm thick commercial ply or AC building board fitted to wooden plug with CP brass screws complete all as specified and directed. |
| 51 | S&F in repairs sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long. |
| 52 | S &F brass chromium plated tubular towel rail 20mm dia, D type, 60cm long between flanges all as specified. Make:- Jaquar/equivalent |
| 53 | S & F for 15 mm bore chromium plated fancy bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule.Make:- cera/Jaquar or equivalent |
| 54 | S & F as in repair 15 mm bore chromium plated fancy type two way bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule. (Make:- Jaquar/equivalent) |
| 55 | S&F15 mm bore angle stop valves cast copper alloy chromium plated screwed down high pressure with crutch or butterfly handle screwed withr iron pipe of union. |
| 56 | S&F Grating doom 125 mm dia with waste hole of ptmt/fency type.(Minimum weight 40gms) |
| 57 | S&F as in repairs CP grab bar 300mm dia compete all as specified and directed (Make : Prayag or jaquar/equivalent) |
| 58 | S&F as in repair CP soap dish compete all as specified and directed (Make : Prayag or jaquar/equivalent) |
| 59 | S&F CP health faucet with 1 mtr flexible tube and hook compete all as specified and directed (Make : Prayag or jaquar/equivalent). |
| 60 | S&F as in repair CP paper holder fixing to wall with ss screw compete all as specified and directed (Make : Prayag or jaquar/equivalent ). |
| 61 | S&F as in repair Chromium plated shower roses with swivel joints, 65mm size, including fixing to steel pipe or union Make:- Jaquar/equivalent |
| 62 | Taking down chowkat or frames with shutters (without taking off shutters from the frames) area exc1.5 but not exc 4 Sqm each. |
| 63 | Taking down chowkat or frames with shutters (without taking off shutters from the frames) area n exc 1.5 Sqm each. |
| 64 | S&F solid PVC moulded door frame of size 50x47mm, made out of 5mm thick one side prelaminated and other side plain colour PVC sheet & edges will be painted to match with prelaminated sheet, reinforced with MS square tube fixed with screw/plugs to brick walls complete all as specified and as directed. |
| 65 | S&F Factory made Solid PVC Moulded Door Shutter 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing, supplying & fixing in the frame at site as per specification & drawing complete all as specified and as directed. |
| 66 | S&F powder coated Anodised aluminium frame for doors, windows ,ventilators, partitions with one or more rebates including joining cleat for fixing etc. complete shall as specified. |
| 67 | S&F powder coated Anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified |
| 68 | S&F powder coated Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.) hinge type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified |
| 69 | S&F 5.5 mm sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 Sqm in each pane complete all as specified and as directed. |
| 70 | S & F in repair 10mm th Toughened glass as in partition / fixed window incl diamond edging all sided , attaching , lining and by sand blasting . Incl CP \\"L' or \\"U\\" heavy duty clamps suitable for fixing of glass , min 4 nos per Sqm all as specified and directed by Engr-in-charge. |
| 71 | S & F in repair 10mm thick Toughened frosted glass door shutters of size area exc 1.50 Sqm but n.exc 3 sqm incl necessary floor spring hydraullically regulated, otherwise fixed on pivot.CP fitting and fixtures , CP handles , CP locking arrangement , necessary cutting & holes moulding and fixed in complete as specified and directed by Engr-in-charge. |
| 72 | M & L for Structural steel, rolled section suchas joist, beam, channel, angle, tee,in available lengths |
| 73 | S&F 35mm thick pre-laminated designer factory made flush shutter of laminate or equivaqlent including necessary hardware and fittings all as specified and directed |
| 74 | Providing and fixing factory made uPVC white color Sliding window Two track made of extruded profiles with wall thickness of 2.3mm (+ 0.2mm). Window profile with hollow section with multi chamber, Frame (60mm x 62mm). sash (42mm x 67mm). Sliding Interlock (One vertical length in each shutters) (45.5mm x 28mm). Glazing bead (24.5mmx 16mm) will he mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc.. making arrangement for fixing of hardware. EPDM gasket 1.2 +0.2mm thick galvanized steel frame (30mm x 21.5mm), Sash (30mm x 18mm), profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners. Hardware : [Touch Lock of zinc alloyed (white powder coated), steel roller system including 5mm thick glazing with selected quality glass, aluminum track on bottom rail for two track sliding frame, wool pine for Sliding sash and interlock.] (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose) & Area exceeding 2.00 sqm each |
| 75 | Providing and fixing factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm ( + 0.2mm). Window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (Onevertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 +0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) [and 5mm thick glazing with selected quality glass.(Note: The unit rate quoted by contractor includes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) |
| 76 | S&F in repairs floor door stopper overall length of cover plate 150 mm of aluminium alloy body and tongue, anodised,with hard drawn steel spring complete all as specified and directed. |
| 77 | S&F in repairs double action floor spring hydraulically regulated made up of min 1.25mm thick Al alloy sheet foundation box,main body with stianless steel cover,governing pivot made of brass, other parts ,made of MS heavy duty and fixed complete for glass/Al door as directed |
| 78 | S&F in repairs Door closer Aluminium (extruded section) body hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed. |
| 79 | S&F stainless steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm, fixed with stainless steel screws complete all as specified and as directed. |
| 80 | M & L for Cement concrete 1:3:6 type C-1 using 20 mm graded stone aggregate in bed block for hold fast complete all as specified and directed |
| 81 | S&F 200 mm long aluminium anodized barrel tower bolt of extruded section complete all as specified and directed |
| 82 | S & F aluminium bow handle,cast type,anodised 125mm long complete fixed with steel screws. |
| 83 | S&F Aluminium sliding door bolts plate type stove enamelled black with bright bolt not less than 12mm dia with & including a min of 6 bolts & nuts four on bolt plate & two on staple plate & fixed 250 mm long |
| 84 | S&F 100mm long Aluminium butt hinges of extruded aluminium alloy with galvanized mild steel hinge , pin anodized complete all as specified |
| 85 | S&F 150 mm long aluminium anodized barrel tower bolt of extruded section complete all as specified and directed |
| 86 | S&F in repair Powder coated aluminium (minimum thickness of powder coating 50 micron) partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions,plain/frosted glass, pvc laminated board with suitable size, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed echanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge |
| 87 | Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets and frame work etc complete all as specified and as directed. |
| 88 | Providing and fixing semi perforated 12mm thick micro tengular edged GRG false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) with semi perforated 12mm thick micro tegular edged false ceiling tiles of size 595 x 595mm of approved texture, design and pattern having moisture content less than 2%, humidity resistance of 90%, NRCO 0.50 to 0.75 as per IS 8225:1987, Nocumbustible as per BS 476 (Part-4) -1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspende on interlocking metal T Grid of hot dipped galvanised iron section of 0.33mm thick (Galvanised @ 120 Grams per sqm including both side) comprising of main T runners of size 15 x 32mm length 3000mm, cross T of size 15 x 32mm length 1200mm and secondary intermediate cross -T of size 15 x 32mm of length 600mm to form grid module of size 600 x 600mm, grid system hanges by 6 mm dia GI wire to purlin, trusses; RCC slab of the roof etc. with hold down clips, butterfly clips, height fixtures etc, Galvanised iron parimeter wall angle of soze 24 x 24 x 0.40mm of length 3000mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per sepcifications, drawing and as per direction of Engineer-in-Charge. (Make: DIAMOND/ GYPROC/ USG BORAL/ KNAUF/ ARMSTRONG) |
| 89 | S&F G.I. Hangers, 6 mm dia, (up to 1200mm length) adjusting level, fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size, 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and as directed. |
| 90 | S & F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to termediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. |
| 91 | M&L for 6mm th Non asbestos fibre cement building boards fixed to GI frame work in ceiling surface. |
| 92 | M&L for false ceiling using powder coated grid system of GI modular grid size 600 x 600 mm with runner 38x24x07 mm cross tee 25x24x0.7 mm and wall angle 24x24x7-8 mm thick PVC laminated Gypsum tiles of size 600 x 600 mm of different designs with rear side MPL film fitted in the grid, grid system hanges by 6 mm dia GI wire to purlin, trusses; RCC slab of the roof etc. with hold down clips, butterfly clips, height fixtures etc, complete all as specified and directed. |
| 93 | S & F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as per specified and as directed. |
| 94 | S&F 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall to make PVC frame as per specification and drawing completed all as specified and as directed. |
| 95 | S & F PVC fluted wall panels of approved make,design,shad, made from rigid PVC extruded with vertical/ribbed/fluted profile,having a thickness not less than 10mm( confirming to IS 12406 and laminated panels confirming to IS 14587) fixed over a prepared surface using suitable adhesive,screws or concealled clip sys as per manufactures specification complete all as specified and directed. |
| 96 | Demolition of brick work built in cm or cement lime mortar |
| 97 | M&L for brick work with fly ash old size bricks straight or curved on plan exc 6 m mean radius built in cm (1:6) complete all as specified and directed at site. |
| 98 | Taking down cement/grit plaster brick wall or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. & removing debris out side MoD land Complete. |
| 99 | M & L 15 mm thick rendering on brick work or concrete surface in cement mortar 1:4 mixed with water proofing compound, (minium 2% by weight of cement or as manufacturer instruction) surface finished even and smooth complete all as specified and as directed. Note : Water proofing compound shall be measured and paid separately as supply only. |
| 100 | M&L for Rendering 5 mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete |
| 101 | Material & labour for preparation of new plastered surfaces of wall and applying two coats of Oil bound distemper over a coat of alkali resistant primer . |
| 102 | M&L for Preparation new plastered or unplastered surfaces of ceiling and applying two coats of oil bound distemper over a coat of alkali resistent primer complete. |
| 103 | M&L for preparing old decorated surfaces of ceiling including cornices etc by washing rubbing down and stopping of distempered surfaces and applying one coat of oil emulsion distemper white or tinted of approved shade complete all as specified and directed. |
| 104 | M&L for complete removal of existing treatment of wall surfaces including cornices etc by washing rubbing down and stopping of distempered surfaces and applying Two coats of oil emulsion distemper white or tinted of approved shade over a coat of wall care putty complete all as specified and directed. |
| 105 | M&L for preparing old painted surfaces of wood or wood base materials of any description not otherwise described, surfaces exc 10 cm width or girth and applying Two coats of synthetic enamel paint complete all as specified and directed. |
| 106 | M&L for preparing old painted surfaces of steel of any description not otherwise described, surfaces exc 10 cm width or girth and applying Two coats of synthetic enamel paint complete all as specified and directed. |
| 107 | M&L for complete removing existing wall finishes any type by vigorously wire brushing brooming, dusting & finally washing with water to clear the cracks absolutely free from any kind of existing finishes & foreign materials, making good minor surface imperfections such as holes, dents cracks etc in cement mortar 1:3 and applying wall care putty 2 to 3mm thick and making surface absolutely smooth applying two coats of exterior emulsion paint (Apex/Weather coat) white or tinted as approved over a coat of primer complete all as specified and directed. |
| 108 | S&F in replacement stainless steel (Grade 304) railing vertical/horizontal made of hollow tubes,channels,plates chains etc,incl welding,grinding,buffing,polishing and making curvature(where ever reqd) and fitting the same with necessary stainless steel nuts and bolts complete,incl fixing the railing with necessary accesories and stainless steel dash fastners,stainless steel bolts ,etc,of reqd size,on top of floor or the side of waist slab with suitable arrangement. |
| 109 | Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed. |
| 110 | Dismantling timber scantlings 40 sq. cm and over in section, in any position (framed work) complete all as specified and as directed. |
| 111 | S&F steel work in tubular column, purline, rafter etc using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St-240 including one shop coat of zinc chromate primer (including preparation of surface) at Contractor’s workshop before fabrication complete all as specified and as directed. |
| 112 | S&F mild steel plate (plain or chequered), channels, square cut or notched (ordinary and counter sunk) forming holes with welded attachment to GI pipe in base/ connections etc. including one shop coat of zinc chromate primer (including preparation of surface) at Contractor’s workshop before fabrication Fe 410 -W (Gde-E- 250) quality-A complete all as specified and as directed. |
| 113 | M&L preparation of new steel surface over 10cm width/girth and applying two coats of synthetic enamel paint complete all as specified and as directed. |
| 114 | S&F in position Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. |
| 115 | S&F Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridge/valley gutter, roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. |
| 116 | Note :- Contractor shall arrange all required machinery & tools, equipments like Hydra, Scaffolding, weling machine, MS pipe bending machine etc and the cost for the same is deemed to be included in the quoted unit rates.Note :- Removing building materials /old waste unwanted existing material of any description or any type etc.on alternate day to a distance of 5km or beyond out side MOD Land and the cost for the same is deemed to be included in the quoted unit rates. Please Enable Macros to View BoQ information |
