|
| 1 | SH: WOOD & PVC WORK |
| 2 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: |
| 3 | 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 4 | SH: STEEL WORK |
| 5 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. |
| 6 | Using flats 30x6mm for diagonal braces and central cross piece |
| 7 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. |
| 8 | Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size). |
| 9 | SH: ROOFING |
| 10 | Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 11 | 0.63 mm thick with zinc coating not less than 275 gm/ m* |
| 12 | Providing and fixing on wall face unplasticised Rigid PVC soil, waste & vent pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, |
| 13 | Single socketed pipes. |
| 14 | 110 mm diameter |
| 15 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 16 | Single tee with door |
| 17 | 110x110x110 mm |
| 18 | Single tee without door |
| 19 | 110x110x110 mm |
| 20 | Bend 87.5° |
| 21 | 110 mm bend |
| 22 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. |
| 23 | 110 mm |
| 24 | SH: FINISHING |
| 25 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer, of required shade and colour all complete : |
| 26 | New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre |
| 27 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : |
| 28 | Two or more coats on new work. |
| 29 | Distempering with 1st quality acrylic distember (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade : |
| 30 | Old work (One or more coats) |
| 31 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : |
| 32 | One or more coats on old work. |
| 33 | SH: REPAIRS TO BUILDING |
| 34 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 metres lead : |
| 35 | With cement mortar 1:4 (1cement: 4 coarse sand). |
| 36 | Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: |
| 37 | Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm). |
| 38 | Providing & fixing White vitreous china water closet squatting pan (Indian type) along with \\"S\\" or \\"P\\" trap including dismantling of old WC seat and \\"S\\" or \\"P\\" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge. |
| 39 | Orissa pattern W.C Pan of size 580x440 mm |
| 40 | SH: SANITARY INSTALLATION |
| 41 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 42 | Semi rigid pipe |
| 43 | 32 mm dia |
| 44 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. |
| 45 | 10 litre capacity - White |
| 46 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete |
| 47 | SH: WATER SUPPLY |
| 48 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. : Internal work - Exposed on wall |
| 49 | 20 mm nominal outer dia. Pipes. |
| 50 | 25 mm nominal outer dia .Pipes. |
| 51 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 52 | Providing and fixing PTMT bib cock of approved quality and colour. |
| 53 | 15mm nominal bore, 86 mm long. Weighing not less than 88 gms. |
| 54 | Providing and fixing PTMT stop cock of approved quality and colour. |
| 55 | 15 mm nominal bore, 86 mm long. Weighing not less than 88 gms. |
| 56 | Providing and fixing PTMT pillar cock of approved quality and colour . |
| 57 | 15mm nominal bore, 107 mm long. Weighing not less than 110 gms. |
| 58 | Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. |
| 59 | 15 mm nominal bore with 45 cm length. |
| 60 | SH: MISC WORK |
| 61 | Cleaning of manholes of sewer line i/c removing & disposal of sludge upto dumping ground in the campus as per direction of Engineer-in-charge. |
| 62 | Cleaning of sewer lines i/c removing & disposal of sludge upto dumping ground in the campus as per direction of Engineer-in-charge. |
| 63 | Cleaning of septic tank by removing night soil, mud etc. by municipal tanker and disposal of sludge upto municipal dumping ground all complete as per direction of Engineer-in-charge. |
| 64 | Providing and fixing aluminium sheet over door shutter of approved quality with required size nails. |
| 65 | Uprooting and removing plants from the surface of the walls, parapet etc. and making good the damages with concrete (1:2:4) as per the direction of Engineer-in-charge. |
| 66 | Small plant of girth of exposed stem upto 75mm lift upto 12 metres. |
| 67 | P/F PVC water storage tank cover of standard quality with locking arrangement as per direction and satisfaction of Engineer-in-charge. Please Enable Macros to View BoQ information |
