|
| 1 | Total of Schedule-A OEW-2213 APPENDIX- 3A PROFORMA FOR STATEMENT OF MINOR DEVIATIONS (Refer Clause C 2.2(d) and C 15.1 of ITT) 1. The following are the particulars of minor deviations from the requirements of the Tender Document: Sr. No Clause Deviations Price reduction for each deviation/s Note : 1. The Tenderer shall indicate price reduction against each deviation in Appendix-3A of BOQ. This price is the price which the tenderer shall reduce from this tender price if deviation(s) is/are accepted by the Employer. 2. Where there is no deviation, the statement should be returned duly signed with an endorsement indicating ‘No Deviations’. In case, Performa of deviations is not submitted or submitted as blank, it will be construed that the tenderer has not proposed any deviations from tender documents. 3. It shall be noted that in case Nil/Zero/NA Price quoted by Tenderer in Appendix-3A then it shall mean that contractor has quoted same price for deviation and undeviation bid. 4. If the tenderer proposes deviations in tender documents, and/or any other terms and conditions of the tender, other than in this Appendix, it will have no effect. Signature of authorized signatory On behalf of Tenderer OEW-2213 S.NO Preamble |
| 2 | The Bill of Quantities shall be read in conjunction with Notice Inviting Tenders, Instructions to Tenderers, General and Special Conditions of Contract, Employer's Requirement and Technical Specification and other relevant documents. |
| 3 | BoQ1 consists of only one schedules i.e. Schedule-A. |
| 4 | Tenderers shall quote their offer in Indian Rupees (₹) only. Tenderers are required to quote percentage (%) Excess/Less for Schedule-A in figures in the appropriate highlighted cells in the BoQ1 sheet. |
| 5 | The rates and prices to be tendered in the unit Priced Bill of Quantities are for completed and finished items of works and complete in all respect. It will be deemed to include Duties, Taxes, Octroi, Royalty etc., cost of all plants, labour, supervision, materials, transport, all temporary works, erection, maintenance, utility identification, contractor’s profit and establishment/overheads, together with preparation of design and drawings, all general risks, insurance liabilities, compliance of labour laws and obligations set out or implied in the contracts. For taxes and duties refer clause C2.4 & C2.5 of ITT & clause 10 of SCC . |
| 6 | The price offer in the BOQ shall be given without considering any deviation mentioned in Appendix-3 of FOT i.e. price in the box shall be quoted as per tender conditions without any deviation. |
| 7 | If the tenderer fails to quote rates against any item, the tender may be treated as incomplete and non-responsive and shall be rejected. |
| 8 | Errors will be corrected by the employer for any arithmetical errors in computation or summation as per contract conditions. |
| 9 | The Financial Proposal (as per BOQ) shall be uploaded online on the website https://etenders.gov.in/eprocure/app The rates shall be quoted in the excel file provided in the bid documents. The tenderer shall download the excel file and quote the rates in BoQ1. After quoting their rates the excel file shall be uploaded accordingly. The rates shall not be offered/quoted elsewhere in the technical submission/ tender submission. |
| 10 | The actual work executed against all the BOQ as detailed in tender document would be paid as per clause 12 of SCC or Clause-22 of ER. |
| 11 | The contractor may raise their “On Account” payments on monthly basis as per the status of work on the last day of the respective month as per clause 12 of SCC. Please Enable Macros to View BoQ information DELHI METRO RAIL CORPORATION Bill of Quantity (BOQ) Contract: OEW-2213: “Rehabilitation of electrical work over L-3E&4 including modification in electrical panel at Metro Niketan staff Quarter”. Sl. No. DESCRIPTION Unit Qty Rate (₹) (Excl. GST) Amount (₹) Schedule-A |
| 12 | SITC of Common area Electrical panel for feeding the electrical supply to Lift of different towers at Metro Niketan Staff quarter with following items Incoming side:- a MCCB ,FP, 630A 36KA, Microprocessor based Release for O/C & S/C (02 Nos), Make-SCH CVS or approved Empanelled make of DMRC b MCCB ACC ROT. HANDLE EXTENDED FOR CVS/NSX 400-630 (02 No's), Make- Schneider or approved Empanelled make of DMRC c MCCB ACC SPREADER 4P FOR NSX400/630 1SET for each MCCB (02 Set), Make- Schneider or approved Empanelled make of DMRC d MCCB ACC AUX. CONTACT 1C/O FOR CVS 100-630A/NSX/NS (04 No's), Make- Schneider or approved Empanelled make of DMRC e MCCB ACC U/V REL. 220-240V AC FOR EASYPACT CVS 100-630A/NSX (02 No's), Make- Schneider or approved Empanelled make of DMRC ELITE 30A f MFM METER CL-1 WITH RS485 AUX 44-300VAC 96 SQMM (02 No's), Make- Secure or approved Empanelled make of DMRC g CT METERING 630/5A 15VA CL-1 ID-80x40 OD-135x95x35MM (06 No's), Make- GNM or approved Empanelled make of DMRC h INDICATING LIGHT RED 220V AC 22.5MM DIA (04 No's), Make- Schneider or approved Empanelled make of DMRC i INDICATING LIGHT YELLOW/ AMBER 220V AC 22.5MM DIA (04 No's), Make- Schneider or approved Empanelled make of DMRC j INDICATING LIGHT BLUE 220V AC 22.5MM DIA (02 No's), Make- Schneider or approved Empanelled make of DMRC k INDICATING LIGHT GREEN 220V AC 22.5MM DIA (02 No's), Make- Schneider or approved Empanelled make of DMRC l MCB SP 6A 10KA C-CURVE (14 No's), Make- Schneider or approved Empanelled make of DMRC OUTGOING side m MCCB, TP, 160A, 36KA, TM REL FOR O/C & S/C (06 No's), Make- SCH CVS or approved Empanelled make of DMRC n MCCB ACC ROT. HANDLE EXTENDED FOR CVS/NSX100/160/250 (06 No's), Make- Schneider or approved Empanelled make of DMRC o MCCB ACC SPREADER 3P FOR NSX100/160/250 1SET for each MCCB (06 Set), Make- Schneider or approved Empanelled make of DMRC p INDICATING LIGHT RED 220V AC 22.5MM DIA (06 No's), Make- Schneider or approved Empanelled make of DMRC q MCB SP 6A 10KA C-CURVE (06 No's), Make- Schneider or approved Empanelled make of DMRC O/G-MCB FEEDER r MCB FP 63A 10KA C-CURVE (02 No's), Make- Schneider or approved Empanelled make of DMRC s MCB DP 63A 10KA C-CURVE (02 No's), Make- Schneider or approved Empanelled make of DMRC |
| 13 | SITC of 160A ATS DB PANEL in machine room for feeding the supply to Lift panel a ATS 160A FP ATySA with controller (01 No's each DB), Make- Socomec or approved Empanelled make of DMRC SOURCE 1 & 2 b INDICATING LIGHT RED 220V AC 22.5MM DIA (02 No's Each DB), Make- Schneider or approved Empanelled make of DMRC c INDICATING LIGHT YELLOW/ AMBER 220V AC 22.5MM DIA (02 No's each DB), Make- Schneider or approved Empanelled make of DMRC d INDICATING LIGHT BLUE 220V AC 22.5MM DIA (02 No's each DB), Make- Schneider or approved Empanelled make of DMRC SOURCE ON e INDICATING LIGHT RED 220V AC 22.5MM DIA (02 No's Each DB), Make- Schneider or approved Empanelled make of DMRC f MCB SP 6A 10KA C-CURVE (8 No's each DB), Make- Schneider or approved Empanelled make of DMRC |
| 14 | Modification in Existing DG Sync panel to feed the supply to common area electrical panel INCOMER side a MCCB FP 630A 50KA MP REL FOR O/C, S/C & E/F, (01 No's), Make- SCH-NSX or approved Empanelled make of DMRC b MCCB ACC ROT. HANDLE EXTENDED FOR CVS/NSX 400-630, (01 No's), Make- Schneider or approved Empanelled make of DMRC c MCCB ACC AUX. CONTACT 1C/O FOR CVS 100-630A/NSX/NS (01 No's), Make- Schneider or approved Empanelled make of DMRC d MCCB ACC FIXED REAR CONNECTOR LONG (2 No's), Make- Schneider or approved Empanelled make of DMRC e MCCB ACC FIXED REAR CONNECTOR SMALL (2 No's), Make- Schneider or approved Empanelled make of DMRC f MCCB ACC TERMINAL SHIELD 4P FOR NSX/CVS 400/630, (2 No's), Make- Schneider or approved Empanelled make of DMRC g CT METERING 630/5A 15VA CL-1 ID-80x40 OD-135x95x35MM (03 No's), Make- GNM or approved Empanelled make of DMRC |
| 15 | Modification in electrical panel for operation of DG in event of failure of one trasnformer supply a AUX RELAY220/240VDC 2C/O 2NO+2NC, Make - Omron or approved Empanelled make of DMRC b RELAY ACC BASE - 8PIN FOR MY, Make - Omron or approved Empanelled make of DMRC c AUX RELA 24VDC 2C/O 2NO+2NC, Make - Schneider or approved Empanelled make of DMRC d TERMINAL-POLYAMIDE 2WAY SCREWLESS GREY FOR 2.5SQMM WIRE, Make - Connectwell or approved Empanelled make of DMRC e TERMINAL-POLYAMIDE 2WAY SCREWLESS GREY FOR 1.5SQMM WIRE, Make - Connectwell or approved Empanelled make of DMRC f WIRE 2.5 SQ MM GREY FRLS, Make - Bonton or approved Empanelled make of DMRC g WIRE 1.5 SQ MM RED FRLS, Make - Bonton or approved Empanelled make of DMRC h WIRE 1.5 SQ MM BLACK FRLS, Make - Bonton or approved Empanelled make of DMRC i TUBE INDOMAX FARUL SLEEVE 2.5MM NORMAL, Make - Reptued or approved Empanelled make of DMRC j TUBE INDOMAX FARUL SLEEVE 1.5MM NORMAL, Make - Reptued or approved Empanelled make of DMRC k PLC PROGRAMING IN LT PANEL, Make - Reptued or approved Empanelled make of DMRC l ACCESSORIES, Make - Reptued or approved Empanelled make of DMRC m Fire Panel starter Modification, Make - TEL or approved Empanelled make of DMRC |
| 16 | Supply and Laying of 3.5core X 300 sqmm Aluminium, Armoured, XLPE, 1.1 KV grade, FRLS cable Including Heavy Duty Clamp, Cable tie and connections etc as per requirement the site conditions. Make: Polycab/KEI/Havelles & Cards Cable or approved Empanelled make of DMRC |
| 17 | Supply and Laying of different size of XLPE, FRLS, Armoured Aluminium Conductor Cables as per IS-7098-{part 1/1988} Make:Polycab/KEI/Ducab/Cards or approved Empanelled make of DMRC a 3.5C X 70 sqmm Metre 1500.0 1200.0 1800000.0 |
| 18 | Supplying and making end termination with brass double compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. Make:- approved Empanelled make of DMRC a 3.5X70 sqmm (38mm) NOS. 20.0 5000.0 100000.0 b 3½ X 300 sq. mm (70mm) NOS. 4.0 9000.0 36000.0 |
| 19 | providing and fixing 25mm X 5mm GI strip on surface or in recess for connections etc as required. Make- approved Empanelled make of DMRC |
| 20 | SITC OF LED based flood light made of Aluminum Die Cast housing. The fixture should have minimum system efficacy of 120 lumens per watt and a mimimum system lumen putput of 3600 lumens and maximum system wattage of 30 WATT. Degree of protection-IP65, Nominal voltage- 220VAC, CCT-5700 to 6500K, Surge Protection>4kV, THD<10%. Make- approved Empanelled make of DMRC |
| 21 | Supplying and installing following size of perforated hot dipped galavanised iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5% in convenient sections, joined with connectors, suspended from the ceiling with GI suspnders including GI bolts and nuts etc as required. Make- approved Empanelled make of DMRC a 150mm width X50mm depth X1.6MM thickness Metre 40.0 404.72 16188.8 b 300mm width X50mm depth X1.6mm thickness Metre 30.0 544.34 16330.2 |
| 22 | SITC of 9.0 Meter hot dipped galvanised Octagonal with single arm & with foundation bolts, base plate complete with foundation, entry and exit pipes, control JB with connector or as per requirement of site conditions. Make- approved Empanelled make of DMRC |
| 23 | SITC OF LED Street light single piece pressure Die Cast Aluminum housing (LM6 Alloy) . The fixture should have minimum system efficacy of 120 lumens per watt and a mimimum system lumen putput of 8400 lumens and maximum system wattage of 70 WATT. Degree of protection-IP65, Nominal voltage- 220VAC, CCT-5700 to 6500K, Surge Protection>4kV, THD<10%. |
| 24 | 3.5 Meter high, 65mm dia MS c class straight tubular pole with base plate and weather proof M.S junction box (made of 16 SWG CRCA sheet having 2 No. 6A DP MCB, 15A rating connecting terminals for 3 Nos 1 phase cables, wiring from junction box to light fitting with 2 run 3x2.5 swmm FR PVC insulated copper wires, the box shall be painted with stove enamelled paint over two coats of primer, installed at 300mm above surface and required welding of base plate from existing structure and support from one or two location for firmly fix the pole or as per requirement of site conditions |
| 25 | Supply, installation testing and commissioning of wiring of LED street light fitting with 2X2.5 sq.mm+1X1.5 sq.mm FRLS, CU multi strand wire duly laid in conduit/pole/ flexible pipe including proper clamping t & connection . Make of wire- approved Empanelled make of DMRC |
| 26 | Supply and installation of IP-65 junction box suitable for mounting on street light pole and cable entry/exit. |
| 27 | providing and fixing of 6 SWG dia. G.I. wire on surface or in recess for loop earthing alongwith existing surface /recessed conduite/submain wiring/cable as required on site condition |
| 28 | SITC of chemical earthing having value value less than 1ohm, length 3.0 meter including chemical dozing if required for improvement of earthing value. The electrode may of copper or GI, which should have higly conductive and resistant to corrosion. Bentonite or charcol may used as backfill material to enhance the soil conductivity and compound should have a resistivity of 0.24 ohm-m and allow leakage current to flow without hinderance . |
| 29 | SITC of DOL starter panel for pump capacity upto 2 HP having protection from Overload and short circuit. Make- approved Empanelled make of DMRC |
| 30 | SITC of Star Delta starter panel from 3HP to 10 KW pump having protection from single phasing, overload and short circuit. Make- approved Empanelled make of DMRC |
| 31 | SITC of MCCB 200A, 4P, 36KA, Model No-DPX3 250, Make- Legrand including dismantling of defective MCCB and associated accessories. Make- approved Empanelled make of DMRC |
| 32 | Developmentof vacant feeder with SITC of 400A MCCB make- schneidere, 4P, 36KA, including Aux contact,UVR, Spreader link, Rotary Handle, indicator and associated accessories like connecting bus bar i/c and o/g side, wiring etc required to complete the work in all respect. Make- approved Empanelled make of DMRC |
| 33 | Developmentof vacant feeder with SITC of 250A MCCB make- schneidere, 4P, 36KA, including Aux contact,UVR, Spreader link, Rotary Handle, indicator and associated accessories like connecting bus bar i/c and o/g side, wiring etc required to complete the work in all respect |
| 34 | Supplying and fixing of 40A to 63A rating, 240/415B, 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commisioning . Make Legrand, ABB, Schneider, Havells or Equivalent or approved Empanelled make of DMRC a 40-63A, 4 pole MCB, 9/10 KA NOS. 5.0 4070.0 20350.0 b 40-60A, 3 Pole MCB, 9/10 KA NOS. 5.0 3160.0 15800.0 |
| 35 | Supply and drawing following sizes of FRLS PVC Insulated copper conductor, single core cable in the existing surface/recessed GI conduit as required. Make- approved Empanelled make of DMRC a wire size 2 X 2.5 sqmm + 1 X 2.5 sqmm earth wire Metre 180.0 42.69 7684.2 |
| 36 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel/GI conduit as required. Make- approved Empanelled make of DMRC a 2X1.5 sqmm + 1X1.5 sqmm earth wire Mtr 250.0 118.39 29597.5 b 2X2.5 sqmm + 1X2.5 sqmm earth wire Mtr 300.0 130.34 39102.0 Total of Schedule A (Exclusive of GST) 5804064.2 GST@18% 1044731.56 Total Schedule A (Inclusive of all, GST@18%) 6848795.76 |
