|
| 1 | Dismantling floor, hearth or wall tiling including cement motar bedding (but not backing), removing serviceable tiles to stores and rubbish of the premisses complete all as specified by directed by Engineer-in-Charge |
| 2 | M & L for Non-Skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tiles over and incliding screed bed 15cm in CM (1:6) complete all as specified and directed. |
| 3 | Material and labour for glazed ceramic tiles coloured of size 350 x 450 x 7mm thick in walls etc, set & jointed in neat cement slurry and pointed in white or colours cement to match the colour of tiles over and including 10mm thick rendring in CM (1:4) complete all as specified and directed. |
| 4 | Demolition of Brickwork or Stone Boulder Masonary, Bulit in Cement Mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed by Engnr-in-Charge |
| 5 | M & L for brickwork with sub-class `B` bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and as directed by the Engineer-in-Charge |
| 6 | Demolition of cement concrete (reinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level ) complete. |
| 7 | Demolition of cement concrete (reinforced) Concrete of any description and in any position not otherwise specifically provided for |
| 8 | Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level ) complete. |
| 9 | Material and labour for 100 mm thick PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) and finishing surfaces of concrete in sub-floors, sub-bases, etc. even and rough to receive the topping layer. complete all as specified and directed. |
| 10 | Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons or Platforms laid bedded in any type of mortar complete all as specified and as directed by Engnr-in-Charge etc. |
| 11 | M&L Granite of 20 mm thick (of any type and colour) work (table rubbed/grinding/ moulding and polished) in steps, jambs, pillars, window cills, cooking platforms, wash basin counter and like over and including 20 mm screed bed in CM 1:3 all as specified and directed. |
| 12 | Providing edge moulding to 18-20mm thick Granite Stone of any Type stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete. |
| 13 | Material and Labour for Machine cut kota stone slab flooring 20-25mm thick over cement screed base of 15 mm thick in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed by Engineer-in-Charge |
| 14 | S & F in Repair, Table top Ceramic Wash Basin Wash Basin of Make Cera of size 600 x 400 x 160 mm or equivalent including Supply and Fix in Repair Bottle Trap of CP bottle traps of Dia 32 mm, for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed, Including PVC connections 15 mm size with PTMT nuts of length 600 mm, including waste pipe complete all as specified and as specified and as directed by Engnr-in-Charge |
| 15 | S & F in Repair, CP Waste coupling of (half or full threaded) (Minimum weight 32 mm 45 gms/40 mm-60 gms), Bore dia of only fixed in discharge pipe (mm) |
| 16 | S & F in Repair ISI marked 15 mm bore stop valves/angle valve cast copper alloy fancy type chromium plated with long shank and cup (concealed type), screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified. |
| 17 | S&F in repairs Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc. (excluding flushing cistern & flush pipe) complete in all respect all as specified.(Pedestal pan and trap, including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc..complete |
| 18 | Supply and fixing in repair Vitreous China squatting pan “Orissa pattern” size 580x440mm white with integral foot rest (excluding flushing cistern and flush pipe) with CI ‘P’ trap of long arm of suitable size including connection to flush pipe, anti symphonic pipes and bed concrete etc complete |
| 19 | Supply and fixingin repair PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets of 10ltrs capacity |
| 20 | Supply only Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern concealed type complete all as specified and as directed. |
| 21 | Supply and fixing for ISI marked 15mm bore, fancy type bib tap of cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed by the Engineer-in-Charge. |
| 22 | Supply and fixing in repair of fancy type pillar taps cast copper alloy with capstan heads, chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed shank supply and fixing ly nuts for iron pipe of 15mm bore fancy type. |
| 23 | S&F in repair two way bib tap 15mm dia complete all as specified and as directed by Engineer-inCharge |
| 24 | S&F in repairs PVC (SWR) floor trap, plain with grating including jointing with solvent cement of outer outlet dia of 75 mm, complete all as specified and as directed by Engnr-in-Charge. |
| 25 | S&F in repir Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified including Health faucet fixing in pipe etc. complete all as specified and as directed. |
| 26 | S&F in repair of Toilet paper holder chromium plated recessed type fixing complete all as specified and directed by engr in charge. Make: Prayag or equivalent |
| 27 | S&F in repair 600mmx450mm Looking mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers |
| 28 | Supply and Fix Chromium plated Tumbler Holder brass screws and wooden/plastic cleats (Minimum weight 300gms) complete all as specified and as directed by Engineer in Charge. |
| 29 | Supply and fixing in repair aluminium hat pegs, solid body 175mm to 250 mm , peg sets of 6 Nos peg set of good quality complete all as specified and directed |
| 30 | S & F Chromium Plated Tubular towel rail, 20 mm dia, D type, 60cm long between flanges complete all as specified and as directed by the Engineer-in-Charge |
| 31 | S & F in repairs Vitreous China Urinal, Flat Back Type of Minimum length 610 mm, white including connecting all the fittings necessary for the functioning of the Urinal complete all as specified and as Directed by Engineer-in-Charge. ( Flat Back Urinal may be choosen by the user from the catalogue of approved make) |
| 32 | Supply and Fix in repair Push tap, suitable for urinals, any colour high pressure of Chromium Plated screwed for iron pipe and fixed, (Minimum weight 15mm-47gms/ 20mm- 75gms) 15 mm bore dia of pipe in complete all as specified and as directed. |
| 33 | Supply and Fix in Repairs, Waste coupling of Chromium Plated suitable for urinals and 32 mm bore dia of discharge pipes (half or full threaded) . (Minimum weight 32mm 45gms/40mm-60 gms |
| 34 | Supply and Fix in Repair, Urinal spreader of Chromium Plated any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) |
| 35 | Supply and Fix in Repair Bottle trap of Chromium Plated having minimum water seal of 25mm .(Minimum weight 32mm-260gms/ 40mm-270 gms) complete all as specified and as directed. |
| 36 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sq. m each complete all as specified and as directed by the Engineer-in-Charge |
| 37 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.5 sq. m but not exc 4 sq. m each complete all as specified and as directed by the Engineer-in-Charge |
| 38 | Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 90 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 39 | S& F of Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 40 | S & F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed by the Engineer-in-Charge. |
| 41 | S&F for 150 mm aluminium handles, cast type, anodised complete all as specified. |
| 42 | S&F for ISI Marked 150mm long aluminium, anodized, barrel tower bolts of extruded section complete all as specified. |
| 43 | S&F 300mm long aluminium allooy anodised sliding door bolts with hasp and staple (bolt type) & fixing clip of sheet cast or extruded section & fixing bolt & sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed. |
| 44 | S&F for 100mm Mild steel butt hinge complete all as specified and directed. |
| 45 | S&F new Door closer hydraulically regulated of Aluminium (extruded section) body,designation No. 3,universal type, suitable for door shutters of 851to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed. |
| 46 | S&F Providing and fixing factory made uPVC white colour casement (Openable) window made of extruded profiles with wall thickness of 2.3mm ( + – 0.2mm). Window profile with hollow section with multi chamber, frame (60mm x 58mm), sash (60mm x 73mm), T profile (One vertical length in between two shutters) (60mm x 74mm), Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 +– 0.2mm thick, galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27.5mm). T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall with 8 mm x 100mm long fasteners. Hardware: [casement handle made of zinc alloyed (white powder coated), But Hinges of'zinc alloyed (white powder coated), transmission gear made of mild steel with multi point locking system] and 5mm thick glazing with selected quality glass.complete all as specified and directed.(Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.) Area of Window not exceeding 1.00 sqm each. |
| 47 | S&F 5.0 mm thick figured glass, pin headed type and glazed oil putty in square not 0.50 sqm in each pane complete all as specified and directed by Engr in charge. |
| 48 | Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified. |
| 49 | Supplying and laying of GI tubing Dia 15 mm medium weight incl fittings on walls / ceilings or Laying in floors complete all as specified. |
| 50 | Taking up or down 20 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified. |
| 51 | Supplying and laying of GI tubing Dia 20mm medium weight incl fittings on walls / ceilings or Laying in floors complete all as specified. |
| 52 | Material and Labour for Cutting chases, pinning in Brick Wall making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and as directed by Engineer-in-Charge |
| 53 | M&L for 10 mm thick rendering in CM 1:6 on fair face of brick/ concrete surfaces finished fair and even without using extra cement complete all as specified and directed. |
| 54 | M&L complete removal of old decorated surface of wall and applying two coat of oil emulsion white/coloured over and including one coat of white cement based putty all as specified and directed by Engr-in-Charge. |
| 55 | M&L for prepration of old ceiling surfaces of any material, applying two coat ofoil emulsion over a coat of white base putty on ceiling all as specified. |
| 56 | Supply & fixing in repair PVC (SWR) pipes single socketed in any length with rubber rings joints laid in fixed to walls including clamps complete all as specified and directed. of the following bore of pipe:- |
| 57 | (a) 110mm |
| 58 | (b) 75mm |
| 59 | Supply & fixing PVC (SWR) junction single (single `T') equal or unequal with accessable door inculding cutting out wall /concrete and finishing of surface to match existing surface complete all as specified and as directed of the following bore:- |
| 60 | (a) 75mm |
| 61 | (b) 110mm |
| 62 | Supply & fixing PVC (SWR) PVC (SWR) vent cowl inculding cutting out wall /concrete and finishing of surface to match existing surface complete all as specified and as directed of the following bore:- |
| 63 | (a) 75mm |
| 64 | (b) 110mm |
| 65 | Supply & fixing PVC (SWR) double (double Y) equal or unequal with accessable door inculding cutting out wall /concrete and finishing of surface to match existing surface complete all as specified and as directed of the following bore:- |
| 66 | (a) 75mm |
| 67 | (b) 110mm |
| 68 | Supply & fixing in repair PVC (SWR) pipe bend with accessable door inculding cutting out wall /concrete and finishing of surface to match existing surface complete all as specified and as directed of the following bore:- |
| 69 | (a) 75mm |
| 70 | (b) 110mm |
| 71 | Material and labour for sunken floor treatment as follows:- |
| 72 | (i) Demolition of cement concrete in sunken floors incl. removing dubrish outside MD land complete all as specified and directed. |
| 73 | (ii) Brushing neat cement slurry with 3.0kg of cement per sq. metre mixed with WPC @ 3% by weight of cement as per manufacturer's instruction to fill all hole and crack complete all as specified and as directed. Note:- Water tightness testing should be done after 24 hours |
| 74 | (iii) Material and labour for PCC (1:2:3) type B-0 using 12.5 mm graded stone aggregate with integral water proofing compound as per manufacturer instructions on bottom of sunken portion with proper slope towards spout and all pipe fixing.Note : Water proofing compound will be measured and paid separately. |
| 75 | (iv)Material and labour for plastering on vertical sides and top surface of CM (1:3) 15 mm thick mixed with water proofing compound as per manufacturer instructions. Plaster shall be extended over PCC coving when the same is green i.e. PCC & plaster be carried out at the same time. Note : Water proofing compound will be measured and paid separately. |
| 76 | (v) Material and labour for 2 coats of Dr. Fixit krystalline waterproofing coating compound shall be applied after laying sewage/ plumbing pipes with fixtures in position. |
| 77 | (vi)Material and labour for filling the sunken floor with PCC ( 1:5:10) type E-2 using bk aggregate over the treated surface. |
| 78 | (vii) Material and labour spouts of 50mm dia GI pipe light grade projecting 450mm clear of face outer wall with PVC mosquito proof cap on inner face of pipe shall be provided to drain out seepage water , if any. |
| 79 | Note : Water tightness testing should be done after applying Dr Fixit epoxy compound, by pounding water for 72 hours & rectify defects if any till total elimination of defect. Dubrish to be removed outside MD land. |
| 80 | Supply and Fix 18 mm thick WPC board exterior grade, decorative both side fixed with screws to timber frame work or with appropriate nails if fixed to the wall and Provn of Locker as directed complete all including Stainless Steel accessories like Magnet Catcher, Knobs, Handles, Pedestal or Cylindrical Type Lock complete all as specified and as directed by Engineer-inCharge |
| 81 | Supply and Fix Hettich Sensys 8645i, 0 Crank Thick Door Hinge For Door Thickness 15 -24 mm With Mounting Plate for overlay Doors, Cupboard Doors, Modular Kitchen Cabinet, Fixed on Mounting Plates, Steel Nickel Plated, with an opening angle of 110 Degree complete all as specified and as directed by Engineer-inCharge |
| 82 | S&F 100mm size Mild steel pressed handles, oval type complete all as specified and as directed by Engineer-inCharge |
| 83 | S&F mild steel, magnetic catches for cabinets of size 50mm complete with striking plate & magnetic stud complete all as per approved sample etc. complete fitting |
| 84 | Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Chief (~1.55Kg/m) |
| 85 | S&F Rough cast, wired figured glass, 6.4mm thick and glazing with oil putty in squares/rec exc .75 but n exc. 1 sqm in each pane complete all as specified and directed |
| 86 | S&F Aluminum composit pannels upto 10mm thick in squares/rec exc .75 but n exc. 1 sqm in each pane complete all as specified and directed |
| 87 | S&F in repair of 50 Watt LED Flood Light fitting, IP-65 or higher protection, die-cast aluminium housing with powder coated finish, toughened glass front cover, complete with high efficiency LED driver, suitable for 230 V, 50 Hz AC supply, including necessary MS mounting bracket/clamp, fixing arrangement on wall/structure/pole, connection with suitable size PVC insulated copper conductor cable, including drilling, nuts, bolts, rawl plugs, and all accessories required for proper installation and operation, complete all as specified and directed by Engineer-in-Charge. |
| 88 | Supply, laying, testing and commissioning of PVC insulated, PVC sheathed, galvanised steel strip/wire armoured electric control cable (heavy duty) with stranded copper conductor of size 3 core × 2.5 sq mm, 1100 volts grade, conforming to relevant IS specifications, laid in existing trench / duct / on wall / ceiling / cable tray / pipe as directed, including dressing of cable, providing and fixing suitable size aluminium cable lugs, double compression brass cable glands, nuts, bolts, washers, making necessary end terminations, crimping, connection to switchgear / DB / light fittings / equipment including earthing continuity, identification ferrules, insulation tape, testing with megger, and commissioning complete all as specified and directed by Engineer-in-Charge. |
| 89 | Supply and fixing steel tubular swaged pole type 410 SP-22 (9 metre long) conforming to relevant IS specifications, complete with cast iron base plate, pole cap, bolts, nuts and washers, including excavation for foundation, PCC foundation (1:3:6) of suitable size, fixing the pole in true vertical position, providing cement concrete coping (1:2:4) around the pole base including curing and dressing the site, painting with one coat of red oxide primer and two coats of aluminium paint, and providing GI strip 25 mm × 4 mm for earthing connection from pole to earth electrode / pit including necessary nuts, bolts, washers and connection, complete all as specified and directed by Engineer-in-Charge. |
| 90 | S&F in repair of LED Building Security light 01 x 30 W new generation energy saving and envirnoment friendly long life made up of pressure die-cast aluminium housing with high power LED as lighting source and lens embedded PC cover in the front and lens for batwing light distribution or having TOP opening seprate driver compartment with IP 66 protection and impact resistance of IK07 for mounting existing bracket complete including all accessories pre-wired with 3 X 1.5 Sqmm single core multistrain copper condutor cable up to celing rose/ terminal box and proper earthing connection must be provided, all as specified and directed by Engr-in-Charge. |
| 91 | Supply, installation, testing and commissioning of 70 Watt LED Flood Light fitting, (only MES approved brand) IP-65 or higher protection, die-cast aluminium housing with powder coated finish, toughened glass front cover, complete with high efficiency LED driver, suitable for 230 V, 50 Hz AC supply, including MS mounting bracket/clamp, fixing arrangement on pole/structure, connection with suitable size PVC insulated copper conductor cable, including drilling, nuts, bolts, rawl plugs and all accessories complete all as specified and directed by Engineer-in-Charge. |
| 92 | Supply and fixing GI pipe medium grade 40 mm dia for protection of cable, including cutting, bending, threading, clamps, saddles, excavation and refilling complete all as specified and directed by Engineer-in-Charge. |
| 93 | Supply and fixing weatherproof junction box made of CRCA sheet steel / polycarbonate enclosure of suitable size with hinged door and rubber gasket, including 6–10 Amp SP MCB, neutral link, earth terminal, terminal connectors and internal wiring, fixed on pole / wall with suitable clamps, nuts, bolts and washers, including connection of incoming cable and outgoing wiring to flood light using PVC insulated copper conductor cable 3 core × 1.5 sq mm, including cable lugs, glands, ferrules, insulation tape, drilling, fixing and making proper terminations, testing and commissioning complete all as specified and directed by Engineer-in-Charge. |
| 94 | Supply, installation, testing and commissioning of 200 Watt LED flood light fitting, IP-65 or higher protection, die-cast aluminium housing with powder coated finish and toughened glass front cover, complete with high efficiency LED driver, suitable for 230 V, 50 Hz AC supply, including providing and fixing suitable MS mounting bracket/clamp on pole/structure, connection of flood light with PVC insulated copper conductor cable from junction box to light fitting, including cable lugs, glands, ferrules, insulation tape, nuts, bolts and washers, making proper terminations and testing, complete all as specified and directed by Engineer-in-Charge. |
| 95 | Supplying laying in trenches and fixing along the poles or passing through pipes or laid under floor of through walls etc jointing and testing LT Cross Linked Polythene Insulated(XLPE insulated) galvanized steel strip armored electric cable 1100 volt grade heavy duty ISI marked with aluminium conductor and overall served with an outer sheath of PVC, of cross sectional area including cable glands made out of finned brass double compression type of size 10 Sqmm 4 Core. Note :- Excavation/road cutting, earthwork, Sand Cushioning, Cable covers, Pipe for cable protection to be measured and paid for separately. |
| 96 | Supplying laying in trenches and fixing along the poles or passing through pipes or laid under floor of through walls etc jointing and testing LT Cross Linked Polythene Insulated(XLPE insulated) galvanized steel strip armored electric cable 1100 volt grade heavy duty ISI marked with aluminium conductor and overall served with an outer sheath of PVC, of cross sectional area including cable glands made out of finned brass double compression type of size 6 Sqmm 3 Core. Note :- Excavation/road cutting, earthwork, Sand Cushioning, Cable covers, Pipe for cable protection to be measured and paid for separately. |
| 97 | Supply and fixing weatherproof junction box of suitable size made of CRCA sheet steel / polycarbonate enclosure with hinged door and rubber gasket, suitable for outdoor installation on lighting pole, including 6–10 Amp SP MCB, neutral link, earth terminal and terminal connectors, complete with internal wiring, fixing on pole with MS clamps, nuts, bolts and washers, including providing and fixing double compression brass cable glands, aluminium lugs, ferrules, identification tags, making necessary incoming and outgoing cable terminations for 3 core armoured cable and connection to flood lights, testing and commissioning complete all as specified and directed by Engineer-in-Charge. |
| 98 | Supply and fixing weatherproof distribution board of suitable size made of CRCA sheet steel with powder coated finish, IP-65 protection, suitable for outdoor installation, including 32 A TPN MCB as incomer and 5 Nos 6 A SP MCB as outgoing feeders, complete with tinned copper busbars, neutral link, earth bar, DIN rail, internal wiring, cable glands, gland plate, phase indication lamps (R-Y-B), circuit identification, hinged door with locking arrangement and mounting arrangement, complete all as specified and directed by Engineer-in-Charge. |
| 99 | Supply and fixing weatherproof distribution board of suitable size made of CRCA sheet steel with powder coated finish, IP-65 protection, suitable for outdoor installation, including 32 A TPN MCB as incomer and 3 Nos 6 A SP MCB as outgoing feeders, complete with tinned copper busbars, neutral link, earth bar, DIN rail, internal wiring, cable glands, gland plate, phase indication lamps (R-Y-B), circuit identification, hinged door with locking arrangement and mounting arrangement, complete all as specified and directed by Engineer-in-Charge. |
| 100 | Excavation or road cutting in trenches not exc 1.5m wide and not exc 1.5M depth for laying of cable, getting out including forming bottom surface to required level and gradient in hard/dense soil.complete all as specified and directed. |
| 101 | M&L for Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in hard/dense soil. complete all as specified and directed. |
| 102 | Removing excavated material/soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.50m above the starting point complete all as specified and directed. |
| 103 | Material and labour for sand cushioning with dry river sand in trenches for cushioning of underground cable line including spreading, leveling, well ramming completed all as specified and directed.Note : Punned thickness only shall be measured and paid. |
| 104 | M & L Bricks laid in trenches flat with width equal to length of brick for cable protection well burnt sub class 'B' laid across the cable complete all as specified. |
| 105 | Supply and fixing in repair of 200 Watt LED Flood Lights suitable for indoor badminton court lighting, having die-cast aluminium housing, high efficiency LED driver, toughened glass cover and IP-66 protection, complete with adjustable wall mounting MS brackets, nuts, bolts and washers for fixing on existing wall, including supply and laying of 3 core 2.5 sqmm copper PVC insulated FRLS cable in 25 mm dia heavy duty PVC conduit with saddles, bends and accessories from nearest lighting distribution board to the fittings, including weatherproof junction boxes, cable glands, lugs, connectors, insulation tape and all minor accessories required for installation, complete with connection, testing, commissioning and proper focusing/aiming of flood lights for uniform illumination of double indoor badminton court, complete all as specified and directed by Engineer-in-Charge |
| 106 | M&L for earthing complete with galvanised steel earth plate 60cmx60cmx6.3 mm thick burried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level connected to galvanised mild steel earthing lead strip 32X6mm by means of bolts nuts check-nuts and washers of galvanized iron or steel as shown in electrical plate No 3 of MES schedule Part-I connecting to earthing test point and testing on completion with including 15mm bore light grade GI protection pipe and watering pipe shall be 20 mm bore, medium grade including excavation & earth work in any type of soil & disposal of soil, providing alternate layers of charcoal and common salt, construction of PCC earth chamber in 1:3:6 type C-1 with 40mm thick RCC 1:2:4 type B-1 cover, reinforced with 8mm TMT bars 100mm C/C both ways with life hook made out oof 8mm dia bars, watering arrangement with funnel & wire mesh, complete all as specified and directed. Note:- (i) The concrete pit shall be PCC (1:3:6) type C-1, 40 mm thick pre cast cover slab of RCC (1:2:4) type B-1 using 20mm graded stone aggregate reinforced with 8mm TMT bars @ 10 cm C/C on both sides with suitable cast iron handle shall be provided in lieu of cast iron cover shown in electrical plate No 3 of MES SSR Part-I.(ii) The unit rate includes the cost of GI pipe light grade for protection of earth strip and earh strip upto 7.5 M. (iii) PCC pit shall be provided at least 500 mm away from the pit and not on the earth pit itself Please Enable Macros to View BoQ information |
